SIG

NAL

CO

ND

ITION

ERS

82

Analog Input Ranges ±150mV, ±1.5V, ±15V, ±150V(Two Isolated Channels) ±2.5mA, ±25mAAnalog Maximum Overload 200V DC for voltage inputs; 170mA DC and/or

(continuous) 60V DC maximum for current inputs (self-resetting fuse)Analog Output Ranges 0-20mA, 0-10V, ±10VAnalog Output Drive 0-20mA: 12VDC compliance. (600Ω maximum)

Voltage ranges: 10mA drive (1000Ω load minumum)Analog Output Accuracy ±0.005% of the FS Input Range (±0.05% on 150 volts

range), plus ±0.05% of the FS Output Range (±0.1% for output loads <200Ω)

Analog Response Time 750msec max. (10-90%)Analog Input Impedance ≥100kΩ on voltage ranges > 1.5V,

≥10MΩ on voltage ranges <1.5V70Ω typical (non-overload) on all current ranges

Analog Output Impedance Less than 3Ω on voltage output ranges≥ 500kΩ on current output ranges

Frequency Input One channel with two voltage range inputs: 150mV to 50Vrms with 5Vp noise suppression, or 0.5V to 150Vrms with 20Vp noise suppression, 2Hz to 10kHz in software selectable ranges.

Frequency Output ±0.1%, 2Hz to 10kHz in software selectable rangesOpen collector pulled up through 20k to 18V, with 1mA drive.Sinks up to 20mA from 24V external supply.

Discrete Input Input active to Common, with soft pull-up (1mA) to +18VCMR (DC to 60Hz) ≥90dB for 60Hz and 120dB @ DCPower Requirements 9-30VDC, 2.5 watts maxIsolation Input to Input to Output to Power, 1800VDCSize DIN rail case (0.88" x 4.0" x 4.59")Operating Temperature 0°C to + 55°C (32 to 131°F)

Q498-0000 DC–Frequency IsolatorC698-0000 Configuration Software & PC Serial CableH902 0.2Amp, 24VDC Power SupplyH910 1Amp, 24VDC Power SupplyH915 2.3Amp, 24VDC Power Supply

The model T798 is a programmable temperature transmitter that can be factory or field configured using the optional 1 or 2 linealphanumeric display.

The model T798 is Highway Addressable Remote Transducer(HART) based, temperature transmitter that can be factory or fieldconfigured using an optional 1 or 2 line alphanumeric display,optional PC based modem and software. Alternatively an HC275Hand-Held Communicator loaded with the Action T798 DeviceDescription from the Hart Foundation Library can be used.

Both the T798 and T797 accept thermocouple (B, C, E, J, K, L, N, R, S, T, U & special) and 2, 3, or 4 wire Platinum RTDs (385 or 392alpha) as well as millivolt (mV) and resistance inputs.

Action Instruments™ IsolatingTwo-Wire Transmitter

Linearization: Thermocouple and RTD linearization to ±0.05°C. Output: Analog, two-wire 4-20 mATransmitter Accuracy: ±0.05% of the millivolt or ohm equivalent input

reading, or the value from the Accuracy Table, whichever is greater; plus ±0.05% of the span. For thermocouples, add ±0.5°C (0.9°F) for cold junction compensation.

Output Analog Zero: 100% of Sensor range —- Non-interacting

Adjustments: Analog Full-scale: Normal or Reverse Acting Operating Temperature: Electronics & Display (with reduced visibility):

-40°C to 85°C, (-40°F to +185°F)Display (full visibility): -20°C to +70°C, (-4°F to +158°F)

SPECIFICATIONS

T797-0000 Temperature Transmitter, Non IST797-1000 Temperature Transmitter, IS-FM/CSAT798-0000 Temperature Transmitter, Hart, Non IST798-1000 Temperature Transmitter, Hart, IS-FM/CSADisplays & OptionsT79D-2000 Two Line Alphanumeric DisplayT79D-1000 One line alpha-numeric DisplayT79E-1000 Weather Proof Head-Mount EnclosureT79A-P000 Pipe Mount Bracket for T79E-0/D onlyT79A-D000 DIN Rail Mounting KitT79A-M000 T797 Configuration ModemT79A-MH00 T798 Hart Configuration ModemT79A-C000 Configuration Software for T797 & T798

ORDERING INFORMATION

Action Instruments™ DC Input, Field Configurable Isolator with Math Functions

SPECIFICATIONS

ORDERING INFORMATION

• Isolated, Linearized Current Loop Output

for an RTD or Thermocouple Input

• HART Compatible or Field

Configurable with Optional Display

• Intrinsically Safe Operation or with

Display and EP Enclosure

• Programmable for 11 T/C Types,

6 RTD Types, mV or Ohm inputs

• Multi-Function, Multi-Channel Input.• DC-Frequency or Frequency-DC

Conversion for Totalization/Integration Applications.

• Math Capability Supports Many Process Control Functions.

• Switch Selectable or PC Programmable Ranges.

The Q498 is a DC powered, DIN rail mount, DC input signal conditioner. The unit is fully isolated to 1800V between input, output and power. Two isolated analog inputs each accept either aDC voltage or current. One analog output delivers either DC bi-polarvoltage or uni-polar current. The Q498 also has a separated frequency input channel and a frequency output, as well as a discrete input and output channel.

The Q498 can perform single or double input math calculations onthe input values. The available operators are: +, -, *, /, Sq, Sqroot& Average. Process control functions include Hi/Lo Select, Rate ofChange Limiter and Track & Hold. The frequency input can alsohave the math functions applied. A 25-point linearization function is available for Channel 1 Analog input only. All output math andprocess control functions require the C698 software.

T79D

SIG

NAL

CON

DIT

ION

ERS

8855

Action Instruments™ Low Profile Signal Conditioners

Pyromation Temperature Transmitters• Wide Operating Temperature Range

• Factory or Field Configurable

• Sensor Break & Short Circuit Detection

• T/C Head Mounting (441 & 442) Industrial or Explosion Proof Housing (642)

• FM & CSA Approved Intrinsically Safe & Non-Incendive

441

642

PM/441 Temperature Head Transmitter PM/442 Temperature Head Transmitter with HART® protocolPM/642A Programmable HART® Transmitter PM/642AT Programmable HART® Transmitter with digital displayPM/642C Programmable HART® Transmitter, explosion proof housingFor factory configuration, specify input type & range (°C or °F); for fieldconfiguration, order communication cable & software

ORDERING INFORMATION

Input: T/C J,K,T,E,R,S,B,N,L,U,C,DRTD Pt or Ni, 100/500/1000, 2/3/4-wire DC -10 to 100mVResistance 400Ω, 2000Ω

Accuracy: 0.2°C (Pt100), 1°C (K T/C)Output: 2-wire, 4-20mA or 20-4mAMaximum Load: (Vsupply - 8V)/25maPower Supply: 8-30V DC (40V max on 642 models)Operating Temperature: -40 to 85°C, condensing allowableDimensions (441, 442): 1.73" dia x 0.9" (44x23mm)Galvanic Isolation: 3.75kV AC

SPECIFICATIONS

• Input, Output, Isolation, Power Supply and Special Functions Combined in One Low Cost Modular Unit

• Field-Settable Range, Span and Configuration

• Fuse Protected Linear Power

• UL Recognized

• High Impact, Flame Retardant Polycarbonate Case

The Series 8000 signal conditioners are designed with a modular architecture to allow full input, output, andspecial function selectability and interchangeability. They can also be used as isolators, signal amplifiers, andtransmitters.

8000-1-1

NLS Series 8000 Signal Conditioners

• Low Power• Higher Accuracy• Field Configurable• E-Mail Alarm Notification

SlimPak II

Output: 0-10V, 0-20mA, 4-20mAAccuracy (In/Out): ±0.015% rng / ±0.05% rng Isolation: 1800V AC/DC, In/Out/PowerOperating Temp: 0 to 60°C, <95% RHPower: 9-30VDC, 1W typ.Alarm: 2 SPDT, 5A@120VACSize: 0.5" wide DIN rail caseApprovals: UL508, CSA C22.2, CE

SPECIFICATIONS

Model Function RangeWV408-2000 DC ±150mV, 1.5/15/150V,

2.5/25mA +reverseWV418-2000 RTD 2/3/4 wire: Pt100, Cu10WV428-2000 T/C J,K,T,R,S,E,B,N,C,BWV438-2000 Potentiometer 100Ω to 100kΩWV448-2000 Bridge ±5/10/20/50/100/200mV

(1-10VDC, 120mA excitation)WV468-2000 AC 50/150/500mV,

5/20/50/150/250V,20/100mA +reverse (40-400Hz)

WV478-2000 Frequency 0-10kHz (150mV-150V)WVC16-2000 Communication Up to 32 modules to

Ethernet 10Base-TC650-2000 Software Includes serial cableWV905 Power Supply 24VDC @0.5AAlso available as Limit Alarms with latching relays & reset switch

ORDERING INFORMATION

TEST

EQU

IPM

ENT

167

Fluke 705 Loop Calibrator• Simultaneous mA and % Readout• Fast “Span Check”• Selectable Slow Ramp,

Fast Ramp & Step• 24V Internal Loop Supply

Fluke 707 Loop Calibrator705 Features, Plus:• Output Adjustment Dial• HART™ Mode• 0.015% Accuracy

Fluke 787 Process Meter• DMM and Loop Calibrator• Backlit LCD• 1000V Overload Protection on V, Ohms,

Frequency

Fluke 789 Process Meter787 Features, Plus:• 24V Loop Power Supply• HART™ Mode• Fast “Span Check”

Fluke 715 Volt/mA Calibrator• Measure loop Currents and Process

Voltages• Source Loop Currents to 24mA• Source Voltage to 10V

Fluke Process Loop Calibrators

Fluke Temperature Calibrators

Functions Fluke 705 and 707 Fluke 715 Fluke 787 and 789

Voltage measurement

Range 0-28 V dc 0-100 mV 0-10 V 0-1000 V ac or dc

Resolution 0.001V 10 µV 1 mV 0.1mV to 1.0V

Accuracy 705: 0.025% Rdg + 1 LSD 0.02% Rdg + 2 LSD 0.1% Rgd + 1 LSD (VDC)707: 0.015% Rdg + 2 LSD

Current measurement

Range 0-24 mA 0-24 mA 0-1A dc 0-30 mA dc

Resolution 0.001 mA 0.001 mA 1mA dc 0.001 mA dc

Accuracy 705: 0.02% Rdg + 2 LSD 0.015% + 2 LSD 0.2%+2 LSD 0.05%+2 LSD707: 0.015% Rdg + 2 LSD

Current sourcing

Range 0-20 mA or 4-20 mA1 0-20 mA or 4-20 mA1 0-20 mA or 4-20 mA1

Accuracy 705: 0.025% Rdg + 2 LSD 0.015% Rdg + 2 LSD 0.05% of span707: 0.015% Rdg + 2 LSD

Drive capability 705: 1000Ω @ 24 mA 1000Ω @ 24 mA 787: 500Ω @ 24 mA707: 1200Ω @ 24 mA 789: 1200Ω @ 24 mA

Loop power while 24V 24V 24V (789 only)measuring mA

Voltage sourcing N/A 0-100 mV or 0-10V N/A

Resistance N/A N/A to 40MΩ, 0.2% + 1 LSDmeasurement

Frequency N/A N/A to 19.999 kHz,0.005% + 1 LSD

Diode test N/A N/A 2.4 V shows diode voltage drop

Continuity N/A N/A Beeps for resistance <100 ohms

Display current Yes mA or % Yesand % of span

Auto step, auto ramp Yes No Yes

Span Check Yes No 789 only1Will over-range to 24 mA

SPECIFICATIONS

Fluke 712 RTD Calibrator• Rosemount® pulsed transmitter

compatible (pulses >100ms)• Measure temperature from RTD output• Simulate RTD output• Operates with seven types of RTD• Measure additional RTDs using Ohms

measurement function• Simulate additional RTDs using Ohms

source function• °F or °C selectable• Four shrouded banana jacks

Fluke 714 Thermocouple Calibrator• Measure temperature from TC output• Simulate TC output• Operable with nine types of

thermocouples• Calibrate linear TC transmitter with

mV source function• Selectable °F or °C• Thermocouple mini-jack termination• Available as accessories: Fluke 700TC1

and TC2 Thermocouple Mini-plug Kits

SPECIFICATIONSModel Function Range Resolution Accuracy NotesFluke-712 Measure/simulate -200 to 800°C 0.1°C, 0.1°F 0.33°C, 0.6°F Pt; 100 200 500 1000 (385);

RTD (Pt 100) (Pt 100) Pt 100 (392); Pt 100 (392) JIS;Ni 120 (672)

Measure/simulate 15 Ω to 3200Ω 0.1Ω 0.1Ω to 1 ΩResistance

Fluke-714 Measure/simulate -200 to 1800°C, 0.1°C or °F 0.3°C + 10 µV 9 TC types; J K T E R S B per NISTThermocouple depending on type (1°C or °F; BRS) 175 and ITS-90 L U per DIN

(K,-200 to 1370°C) 43710 and PTS-68Measure/simulate -10 to 75 mV 0.01 mV 0.025%

mV + 1 count

712

787

705

TESTE

QU

IPMEN

T

166

Martel Beta Process CalibratorsMulti-Function• Measure and source T/Cs, RTDs, Ohms,

current, voltage, frequency; source pulse trains• Isolated mA/V read-back for

complete transmitter calibration• Pressure module communication port • Built-in 24 V supply drives 4–20mA loops • Direct entry of custom RTD coefficients • All source modes can be programmed with

setpoints to speed linearity tests• Highest accuracy in class (to 0.015% rdg.)

MC–1200

Read and Source Voltage Current (mA)Source 0.000 to 20.000 VDC 0.000 to 24.000 mARead Isolated 0.000 to 30.000 VDC 0.000 to 24.000 mARead Non-isolated 0.000 to 20.000 VDC 0.000 to 24.000 mAAccuracy ±0.015% of rdg ±2 µV ±0.015% of rdg ±2 µA

SPECIFICATIONS

Universal Temperature• Calibrate thermocouples and RTDs with

one unit• Works with smart (pulsed) transmitters• Direct keyboard entry or scroll control• 9 user-defined setpoints for each type• Rugged NEMA 4X case• High accuracy ±0.4°C J T/C,

±0.3°C 4w RTD• Auto step function PTC–8001

SPECIFICATIONSRead & Source RangeJ -200.0 to 1200.0 K -200.0 to 1370.0T -200.0 to 400.0 E -200.0 to 950.0 R -20.0 to 1750.0 S -20.0 to 1750.0 B 600.0 to1800.0 L -200.0 to 900.0 U -200.0 to 400.0 N -200.0 to 1300.0mV -10.0 to 75.00

NI120 (672) -80.0 to 260.0 Pt 100 (385) -200.0 to 800.0 Pt 100 (3926) -200.0 to 630.0 Pt 100 (3916) -200.0 to 630.0 Pt 200 (385) -200.0 to 630.0 Pt 500 (385) -200.0 to 630.0 Pt 1000 (385) -200.0 to 680.0Cu10 -100.0 to 250.0YSI400 15.0 to 50.0 Ohms 0.0 to 400.0,

400 to 3200plus Pt 392, JIS, Ni120

Connectors: Standard mini-plug for T/C, banana jack for RTDsOperating Temp.: -10 to +50 °CDimensions: 8.7" H x 4.2" W x 2.3" D

ResolutionVoltage: 0.01 mV, 0.0001 V, 0.001VCurrent: 0.001 mA

Accuracy: ±0.015% of reading, ±2 count; 18 °C to 28 °C

Temp. Stability: ±0.005% FS/°CLoad Capability

Voltage: ±1 mA for rated accuracyCurrent: 1kΩ

Output Protection: Current limited internal RESETOperating Temp: -10 °C to +55 °CDimensions: 1.43" x 3.15" x 5.7"

SPECIFICATIONS

Voltage/Current Calibrator• 0.015% of reading

accuracy• 200 mV, 2 V, 20 V and

24 mA ranges• 24 V supply can drive

4-20 mA loops • 2 stored setpoint values• Intuitive, easy-to-use

controls IVC-222HPII

Operating Temperature: -10 °C to +50 °C Stability: ±0.005% of reading/ °C outside 18-28 °C Dimensions 8.7" x 4.2" x 2.3"

MA/MC-1200 Multi-Function Calibrator with test leads, 4 AA batteries, NIST certificate

MA/PTC8001 Universal Temperature Calibrator with test leads, 4 AA batteries, NIST certificate

MA/IVC-222 HP11 Voltage/Current Calibrator with test leads, carrying case, 9V battery, NIST certificate

MA/TC-100 Thermocouple Calibrator with 9V battery, NIST certificate

MA/LC-100 Loop Calibrator with test leads, 9V battery, NIST certificate

MA/CC572 Carrying Case for PTC8001, MC-1200A variety of temperature probes are available.

ORDERING INFORMATION

Thermocouple Calibrator• 10 T/C types plus mV• ±0.3°C accuracy (type J)• Accepts T/C mini-plug

& bare T/C wires• 3 setpoints for each T/C type• MIN/MAX recall in

measure mode• Input protection to 240 VAC TC-100

Voltage Source & MeasureRange: -10 to +75.000 mVResolution: 1 µVAccuracy: ±0.007% of reading,

±10 µVOutput Impedance: ≤1 ΩInput Impedance: >1 MΩ

Thermocouple Source/MeasureTypes: J, K, T, E, R, S, B, L, U, CResolution: 0.1°C or °F source

0.01°C or °F measureOperating Temp: -10 °C to +55 °CDimensions: 5.7" x 3.15" x 1.43"

SPECIFICATIONSCurrent Source & Measure

Range: 0.000 to 24.000 mA, -25 to +125 %

Voltage (Reading): 0 to 28 VDCInput Protection: Fuseless, up to 250 VACDrive Capability: 1200Ω without Hart,

950Ω with HartLoop Supply: 24 VDCRange Select: Decade Incremental to

0.001 mA stepsResolution: 1 µAAccuracy: ±0.015% of reading ± 2 µAOperating Temp.: -10 to +55 °CDimensions: 5.7" x 3.15" x 1.43"

SPECIFICATIONS

Loop Calibrator• Simulates, powers & measures

two-wire transmitters• Five preset outputs

(4, 8, 12, 16, 20 mA)• 0.001 mA resolution • Adjustment level knob• % Error function eliminates

manual calculation• Measures loop power &

Hart devices LC-100

Thermocouple mVRead & Source -10.000 to +75.000 mVAccuracy ±0.02% of rdg, ±10 µVOhmsSource 5.0 to 4000ΩRead 0.00 to 4000.0ΩRead and Source Range (Accuracy) °CNi120 (672) -80.0 to +260.0 (0.2)Pt100 (385) -200.0 to +800.0 (0.2)Pt100 (3926) -200.0 to +630.0 (0.2)Pt100 (3916) -200.0 to +630.0 (0.2)Pt200 (385) -200.0 to +630.0 (0.8)Pt500 (385) -200.0 to +630.0 (0.4)Pt1000 (385) -200.0 to +630.0 (0.2)Cu10 -100.0 to +260.0 (1.4)YSI400 +15.00 to +50.00 (0.1)Cu50 -180 to +200 (0.4)Cu100 -180 to +200 (0.3)Pt385-10 -200 to +800.0 (1.4)Pt385-50 -200 to +800.0 (0.4)

Frequency (1-20 V amplitude)CPM Source & Read 2.0 to 600.0 CPMHz Source & Read 1.0 to 1000.0 HzkHz Source & Read 1.0 to 10.00 kHzPulse Source (1-20 V amplitude)Pulses 1 to 30,000.0 Rate 2 CPM to 10 kHz Read and Source Range (Accuracy) °CJ -200.0 to +1200.0 (0.2)K -200.0 to +1370.0 (0.3)T -200.0 to +400.0 (0.2)E -200.0 to +950.0 (0.2)R -20.0 to +1750.0 (1.2)S -20.0 to +1750.0 (1.2)B +600.0 to +1800.0 (1.2)C 0 to +2316.0 (0.6)XK -200.0 to +800.0 (0.2)BP 0 to +2500.0 (0.9)L -200.0 to +900.0 (0.2)U -200.0 to +400.0 (0.25)N -200.0 to +1300.0 (0.4)

SIG

NAL

CO

ND

ITION

ERS

86

10AI Model 10 Auto-Isolator10AI-EXP Model 10 in Explosion Proof Housing

SPECIFICATIONS

ORDERING INFORMATION

Pyragon Loop Isolator• Signal Powered CMOS Circuitry

• Precise Duplication of Input Signals

• 4–20 or 10–50 mA, Same Unit

• High Common Mode Rejection

• 1500 VRMS Isolation

• Mounts on Bulkhead or in 3" Conduit Box

Provides the Necessary Signal Isolationfor Noisy Process CircuitsIf your process signals are influenced byground loops, high common mode noise, orother interference, you need the TransmationModel 10 Auto-Isolator. Requiring no separatepower supply, Auto-Isolator operates efficientlyfrom input signal current, and preciselyretransmits the current applied to the inputwith an accuracy of ±0.1% of span.

Usable with milliamp signal ranges of 4–20,10–50, or other ranges between 4 and 50 mA. The instrument can be bulkhead-mounted or installed in a 3-inch cast conduit box. A trim potentiometer, accessible through the instrument’s top plate, permits preciseadjustment of current transfer as a function of load resistance up to 500 ohms at 20 mA,and 250 ohms at 50 mA.

Input: 4–20 mA, 10–50 mA, or other spans within range of 4–50 mAOutput Ratings: 4–20 mA with loads from 0–500 ohms

10–50 mA with loads from 0–250 ohmsAccuracy: ±0.1% of spanSize/Weight: 2.95" diameter, 1.88" high/6 oz

10AI

2800T Universal Temperature Transmitter, Digital Display (NI FM Approved)

2800T-EXP 2800T in Explosion Proof Housing2850T 2800T with HART Protocol100665-651 32 mm DIN Rail Adaptor—2800T100665-652 35 mm DIN Rail Adaptor—2800T

ORDERING INFORMATION

• Configurable for Eight T/Cs, 12 RTDs, Millivolts, Ohms

• Unmatched Programmability: Input Type, Range, Zero, Span, Linear Output, EngineeringUnits; Calibration Runs

• Exceptionally Economical: Reduces Inventory and Maintenance Costs

• Built for Reliability: RFI Protected, Isolated, Environmentally Tough, Five-Year Warranty

SPECIFICATIONSInput Types

Thermocouple: Types J, K, T, E, R, S, N, BRTD: Pt DIN 43760 (50, 100, 200, 500Ω); Pt JIS C 1604 (100Ω);

Pt Burns 0.003902α (100, 200, 500Ω); Ni Bristol’s 7NA(110Ω); Ni Minco (120Ω); Cu Minco (10Ω); Cu China0.00428α (50Ω)

mV: -100 to + 100 mVResistance: 0 to 1000Ω Accuracy: ±0.05% of span ±1 digitInput Span Limits: Any span within range limitsInput Resolution: 0.1°, 1 µV, 0.005ΩOutput Range: 4 to 20 mA, calibrated; 3.7 to 22 mA, maximumOutput Resolution: 0.002 mARTD Excitation Current: 200 µA, typicalTemperature Effect

T/C and mV: ±0.2 µV/°C max ±0.005% of input reading/°CRTD and Ω: ±0.002 Ω/°C max ±0.005% of input reading/°C

Loop Supply Voltage: 13V + (load resistance x 20 mA), min; 48V, maxSize 3.10 x 1.75 x 3.77" HWD

Pyragon Universal Temperature Transmitters

2800T