PV SURGE ARRESTERS – CLASS I+II/T1+T2 PVB12.5 ......T1+T2/Class I+II PV SPD per IEC...
1
T1+T2 (IEC/EN) Surge Protective Device (SPDs) are designed for PV/Photovoltaic system dc-side protection against the damaging from surges and spikes caused by lightning and other electrical sources. ■ T1+T2/Class I+II PV SPD per IEC 61643-31/EN50539-11 ■ Prewired Y protection circuit, for common mode and differential mode protection ■ Surge capacity up to 100kA 8/20μs per pole ■ Lightning impulse current 12.5kA 10/350μs per pole ■ Reliable supervision due to disconnection device; ■ Degradation indication and optional alarm signal optional PV SURGE ARRESTERS – CLASS I+II/T1+T2 PVB12.5/1500-MVCDR Type In accordance with Category IEC/VDE Protection Mode Max. continuous operating voltage Nominal discharge current(8/20μs) Max. discharge current(8/20μs) Lightning impulse current (10/350μs) per pole Total Discharge Current (10/350us) Voltage protection rating Response time Short circuit withstand capacity (Iscpv) Operating temperature range Cross-section of connection wire Mounting Enclosure material Degree of protection Installation width Thermal disconnector Remote alarm contact Additional data for Remote Alarm Contacts Remote alarm contact type Switching capability Un/In Max. Size of connecting wire Ucpv In Imax Iimp Itotal (10/350) Up PVB12.5/1500-MVCDR EN50539-11; IEC61643-31 I+II/B+C Common mode & Differential mode 1500Vdc 30kA 100kA 12.5kA 25kA <5.5kV ≤25 ns 1000A - 40°C ~ + 85°C Single-strand 35mm 2 ; multi-strand 25mm 2 35mm DIN-rail in accordance with EN 50022/DIN46277-3 thermoplastic; extinguishing degree UL94 V-0 IP20 6 modules, DIN 43880 Internal green – normal ; red - failure Yes Isolated Form C AC: 250V/0.5A DC: 250V/0.1A; 125V/0.2A; 75V/0.5A Max. 1.5mm 2 (or # 16AWG) Dimension drawing Basic circuit diagram JD Auspice Co.,Ltd. TEL: 886-2-8991-2796 FAX: 886-2-8991-9298 [email protected] www.jdauspice.com 日煬科技有限公司 JD Auspice Co., Ltd JDA PVB12.5/1500-MVCDR
Transcript of PV SURGE ARRESTERS – CLASS I+II/T1+T2 PVB12.5 ......T1+T2/Class I+II PV SPD per IEC...
T1+T2 (IEC/EN) Surge Protective Device (SPDs) are designed for PV/Photovoltaic system dc-side protection against the damaging from surges and spikes caused by lightning and other electrical sources.
■ T1+T2/Class I+II PV SPD per IEC 61643-31/EN50539-11■ Prewired Y protection circuit, for common mode and di�erential mode protection■ Surge capacity up to 100kA 8/20μs per pole■ Lightning impulse current 12.5kA 10/350μs per pole■ Reliable supervision due to disconnection device;■ Degradation indication and optional alarm signal optional
PV SURGE ARRESTERS – CLASS I+II/T1+T2PVB12.5/1500-MVCDR
TypeIn accordance withCategory IEC/VDEProtection ModeMax. continuous operating voltageNominal discharge current(8/20μs)Max. discharge current(8/20μs)Lightning impulse current (10/350μs) per poleTotal Discharge Current (10/350us)Voltage protection rating Response timeShort circuit withstand capacity (Iscpv)Operating temperature rangeCross-section of connection wireMountingEnclosure materialDegree of protectionInstallation widthThermal disconnectorRemote alarm contactAdditional data for Remote Alarm ContactsRemote alarm contact typeSwitching capability Un/InMax. Size of connecting wire
UcpvIn
ImaxIimp
Itotal (10/350)Up
PVB12.5/1500-MVCDREN50539-11; IEC61643-31I+II/B+CCommon mode & Di�erential mode1500Vdc30kA100kA12.5kA25kA<5.5kV≤25 ns1000A- 40°C ~ + 85°CSingle-strand 35mm2 ; multi-strand 25mm2
35mm DIN-rail in accordance with EN 50022/DIN46277-3thermoplastic; extinguishing degree UL94 V-0IP206 modules, DIN 43880Internal green – normal ; red - failureYes
Isolated Form CAC: 250V/0.5A DC: 250V/0.1A; 125V/0.2A; 75V/0.5AMax. 1.5mm2(or # 16AWG)
Dimension drawingBasic circuit diagram
JD Auspice Co.,Ltd. TEL: 886-2-8991-2796 FAX: 886-2-8991-9298 [email protected] www.jdauspice.com
日煬科技有限公司JD Auspice Co., Ltd
JDA PVB12.5/1500-MVCDR
