Gasket factors Dichtungsfaktoren - Klinger Service...Spiral wound gasket (graphite filler) Metal...
1
KLINGERSIL ® Type KLINGERSIL ® C-4300 KLINGERSIL ® C-4400 KLINGERSIL ® C-4409 KLINGERSIL ® C-4430 KLINGERSIL ® C-4500 KLINGERSIL ® C-4509 KLINGERSIL ® C-8200 KLINGERtop-chem and top-graph Type KLINGERtop-chem 2000 KLINGERtop-chem 2003 KLINGERtop-chem 2005 KLINGERtop-graph 2000 KLINGERgraphit Laminate Type PSM 100 PSM 200 PSM 300 SLS 100 SLS 200 SLS 300 Metal gaskets Type Spiral wound gasket (graphite filler) Metal clad gasket (soft iron) thick- ness mm 1 2 3 1 2 3 1 2 1 2 3 1 2 3 1 2 1 2 3 thick- ness mm 1 2 3 2 2 2 thick- ness mm 1 2 3 1 2 3 σ VO MPa 25°C 158 120 48 240 240 63 240 240 >240 >240 133 220 180 100 280 180 225 150 75 σ VO MPa 25°C 253 210 100 >110 >110 >160 σ VO MPa 25°C 210 140 95 195 125 80 σ Vu 0,1 MPa 25°C 15 18 20 18 23 24 39 43 22 29 29 23 26 28 24 28 17 19 21 σ Vu 0,1 MPa 25°C 21 21 21 13 28 25 σ Vu 0,1 MPa 25°C 30 20 20 20 20 20 MPa 50°C 120 80 40 195 110 53 215 110 260 240 97 195 110 80 195 110 160 110 55 MPa 50°C 214 185 87 110 50 120 MPa 50°C 210 140 95 180 110 75 MPa 100°C 63 52 29 95 80 41 176 80 145 120 65 120 110 55 140 110 70 53 26 MPa 100°C 150 150 60 28 35 80 MPa 100°C 200 130 90 160 100 70 MPa 200°C 39 33 18 50 42 24 120 42 81 73 40 68 59 33 120 59 44 34 17 MPa 200°C 125 125 50 15 22 70 MPa 200°C 195 120 85 130 90 60 MPa 300°C 38 30 80 30 65 56 31 51 43 23 97 43 MPa 250°C 75 75 33 10 15 60 * * 300°C MPa 300°C 190 110 80 110 75 50 k 1 mm 1.1 x b D 1.1 x b D 1.1 x b D 1.1 x b D 1.1 x b D 1.1 x b D 1.1 x b D 1.1 x b D 1.1 x b D 1.1 x b D 1.1 x b D 1.1 x b D 1.1 x b D 1.1 x b D 1.1 x b D 1.1 x b D 1.1 x b D 1.1 x b D 1.1 x b D k 1 mm 1.1 x b D 1.1 x b D 1.1 x b D 1.1 x b D 1.1 x b v k 1 mm 3xb D 2xb D 2xb D 2xb D 2xb D 2xb D K O xK D (N/mm) 22xb D 22xb D 22xb D 22xb D 22xb D 22xb D 28xb D 28xb D 22xb D 22xb D 22xb D 22xb D 22xb D 22xb D 28xb D 28xb D 22xb D 22xb D 22xb D K O xK D (N/mm) 25xb D 25xb D 25xb D 22xb D 22xb D K O xK D (N/mm) 30xb D 10xb D 7xb D 6xb D 6xb D 6xb D ”m” factor 2.7 3.0 3.3 3.2 3.5 3.9 3.2 3.5 4.5 5.0 5.5 3.5 4.0 4.5 3.5 4.0 3.5 4.0 4.5 ”m” factor 4.7 5.0 5.2 2.8 10.0 4.0 ”m” factor 3.0 2.0 2.0 2.0 2.0 2.0 ”m” factor 3.0 3.0 ”y”Stress MPa 15.0 15.0 15.0 20.0 20.0 20.0 30.0 30.0 25.0 25.0 25.0 25.0 25.0 25.0 30.0 30.0 22.5 22.5 22.5 ”y”Stress MPa 10.0 10.0 10.0 5.0 10.0 25.0 ”y”Stress MPa 30.0 10.0 6.0 6.0 6.0 6.0 ”y”Stress MPa 68.9 31.0 Gasket factors σ BO (7.2.2) DIN 28090/DIN 28091 DIN 2505 ASTM σ BO (7.2.2) DIN 28090/DIN 28091 DIN 2505 ASTM σ BO (7.2.2) DIN 28090/DIN 28091 DIN 2505 ASTM The evaluation of these characteristic datas are based on the rules of DIN 28090. The use of this values will not guarantee the performance of the gasket. Application conditions not in the control of the gasket material manufacturer can influence the operation of the gasket. A deducation of liability claims of any nature is therefore not possible. As further investigations are continuosely carried out we reserve the right of appropriate updates. The design factors ”m” and ”y” according to the ASME Code are based on a maximum leakage rate of 1 ml/min. approx. 0.1 mg/sec x m measured according to DIN 28090 at different gas pressures and different gasket stresses. The DIN 2505 and the ”y” and ”m” concept itself now being questioned as a valid design tool. Subject to technical alterations. Status: October 2002 KLINGER GmbH P.O. Box 1370, D-65503 Idstein Rich.-Klinger-Straße, D-65510 Idstein Tel +49 (0) 61 26 950-0 Fax +49 (0) 61 26 950 340/341 e-mail: [email protected] http://www.klinger-gmbh.de
Transcript of Gasket factors Dichtungsfaktoren - Klinger Service...Spiral wound gasket (graphite filler) Metal...
KLINGERSIL®
Type
KLINGERSIL® C-4300
KLINGERSIL® C-4400
KLINGERSIL® C-4409
KLINGERSIL® C-4430
KLINGERSIL® C-4500
KLINGERSIL® C-4509
KLINGERSIL® C-8200
KLINGERtop-chem and top-graphType
KLINGERtop-chem 2000
KLINGERtop-chem 2003KLINGERtop-chem 2005KLINGERtop-graph 2000
KLINGERgraphit LaminateType
PSM 100PSM 200PSM 300SLS 100SLS 200SLS 300
Metal gasketsTypeSpiral wound gasket (graphite filler)Metal clad gasket (soft iron)
thick-nessmm
1231231212312312123
thick-nessmm
123222
thick-nessmm
123123
σVO
MPa25°C
15812048
24024063
240240
>240>24013322018010028018022515075
σVO
MPa25°C
253210100
>110>110>160
σVO
MPa25°C
21014095
195125
80
σVu 0,1
MPa25°C
15182018232439432229292326282428171921
σVu 0,1
MPa25°C
212121132825
σVu 0,1
MPa25°C
302020202020
MPa50°C
1208040
19511053
21511026024097
195110
8019511016011055
MPa50°C
214185
87110
50120
MPa50°C
21014095
18011075
MPa100°C
635229958041
17680
14512065
12011055
140110
705326
MPa100°C
150150
60283580
MPa100°C
200130
90160100
70
MPa200°C
393318504224
12042817340685933
12059443417
MPa200°C
125125
50152270
MPa200°C
19512085
1309060
MPa300°C
3830
80306556315143239743
MPa250°C
7575331015
60 ** 300°C
MPa300°C
190110
801107550
k1
mm1.1 x bD
1.1 x bD
1.1 x bD
1.1 x bD
1.1 x bD
1.1 x bD
1.1 x bD
1.1 x bD
1.1 x bD
1.1 x bD
1.1 x bD
1.1 x bD
1.1 x bD
1.1 x bD
1.1 x bD
1.1 x bD
1.1 x bD
1.1 x bD
1.1 x bD
k1
mm1.1 x bD
1.1 x bD
1.1 x bD
1.1 x bD
1.1 x bv
k1
mm3 x bD
2 x bD
2 x bD
2 x bD
2 x bD
2 x bD
KOx KD
(N/mm)22 x bD
22 x bD
22 x bD
22 x bD
22 x bD
22 x bD
28 x bD
28 x bD
22 x bD
22 x bD
22 x bD
22 x bD
22 x bD
22 x bD
28 x bD
28 x bD
22 x bD
22 x bD
22 x bD
KOx KD
(N/mm)25 x bD
25 x bD
25 x bD
22 x bD
22 x bD
KOx KD
(N/mm)30 x bD
10 x bD
7 x bD
6 x bD
6 x bD
6 x bD
”m”factor
2.73.03.33.23.53.93.23.54.55.05.53.54.04.53.54.03.54.04.5
”m”factor
4.75.05.22.8
10.04.0
”m”factor
3.02.02.02.02.02.0
”m”factor
3.03.0
”y”StressMPa15.015.015.020.020.020.030.030.025.025.025.025.025.025.030.030.022.522.522.5
”y”StressMPa10.010.010.0
5.010.025.0
”y”StressMPa30.010.0
6.06.06.06.0
”y”StressMPa68.931.0
Gasket factors
σBO (7.2.2)DIN 28090/DIN 28091 DIN 2505 ASTM
σBO (7.2.2)DIN 28090/DIN 28091 DIN 2505 ASTM
σBO (7.2.2)DIN 28090/DIN 28091 DIN 2505 ASTM
The evaluation of these characteristic datasare based on the rules of DIN 28090. Theuse of this values will not guarantee the performance of the gasket. Application conditions not in the control of the gasketmaterial manufacturer can influence the operation of the gasket. A deducation of liability claims of any nature is therefore not possible. As further investigations arecontinuosely carried out we reserve the rightof appropriate updates.
The design factors ”m” and ”y” according tothe ASME Code are based on a maximumleakage rate of 1 ml/min. approx. 0.1 mg/sec x m measured according to DIN 28090 at different gas pressures anddifferent gasket stresses. The DIN 2505 and the ”y” and ”m” conceptitself now being questioned as a validdesign tool.
KLINGERSIL®
Typ
KLINGERSIL® C-4300
KLINGERSIL® C-4400
KLINGERSIL® C-4409
KLINGERSIL® C-4430
KLINGERSIL® C-4500
KLINGERSIL® C-4509
KLINGERSIL® C-8200
KLINGERtop-chem u. top-graphTyp
KLINGERtop-chem 2000
KLINGERtop-chem 2003KLINGERtop-chem 2005KLINGERtop-graph 2000
KLINGERgraphit LaminatTyp
PSM 100PSM 200PSM 300SLS 100SLS 200SLS 300
Metallische DichtungenTypSpiraldichtungen(Graphitfüllband)Metallummantelte Dichtungen (Weicheisen)
Dicke
mm1231231212312312123
Dicke
mm123222
Dicke
mm123123
σVO
MPa25°C
15812048
24024063
240240
>240>24013322018010028018022515075
σVO
MPa25°C
253210100
>110>110>160
σVO
MPa25°C
21014095
195125
80
σVu 0,1
MPa25°C
15182018232439432229292326282428171921
σVu 0,1
MPa25°C
212121132825
σVu 0,1
MPa25°C
302020202020
MPa50°C
1208040
19511053
21511026024097
195110
8019511016011055
MPa50°C
214185
87110
50120
MPa50°C
21014095
18011075
MPa100°C
635229958041
17680
14512065
12011055
140110
705326
MPa100°C
150150
60283580
MPa100°C
200130
90160100
70
MPa200°C
393318504224
12042817340685933
12059443417
MPa200°C
125125
50152270
MPa200°C
19512085
1309060
MPa300°C
3830
80306556315143239743
MPa250°C
7575331015
60** 300°C
MPa300°C
190110
801107550
k1
mm1,1 x bD
1,1 x bD
1,1 x bD
1,1 x bD
1,1 x bD
1,1 x bD
1,1 x bD
1,1 x bD
1,1 x bD
1,1 x bD
1,1 x bD
1,1 x bD
1,1 x bD
1,1 x bD
1,1 x bD
1,1 x bD
1,1 x bD
1,1 x bD
1,1 x bD
k1
mm1,1 x bD
1,1 x bD
1,1 x bD
1,1 x bD
1,1 x bv
k1
mm3 x bD
2 x bD
2 x bD
2 x bD
2 x bD
2 x bD
KOx KD
(N/mm)22 x bD
22 x bD
22 x bD
22 x bD
22 x bD
22 x bD
28 x bD
28 x bD
22 x bD
22 x bD
22 x bD
22 x bD
22 x bD
22 x bD
28 x bD
28 x bD
22 x bD
22 x bD
22 x bD
KOx KD
(N/mm)25 x bD
25 x bD
25 x bD
22 x bD
22 x bD
KOx KD
(N/mm)30 x bD
10 x bD
7 x bD
6 x bD
6 x bD
6 x bD
”m”factor
2,73,03,33,23,53,93,23,54,55,05,53,54,04,53,54,03,54,04,5
”m”factor
4,75,05,22,8
10,04,0
”m”factor
3,02,02,02,02,02,0
”m”factor
3,03,0
”y”StressMPa15,015,015,020,020,020,030,030,025,025,025,025,025,025,030,030,022,522,522,5
”y”StressMPa10,010,010,0
5,010,025,0
”y”StressMPa30,010,0
6,06,06,06,0
”y”StressMPa68,931,0
Dichtungsfaktoren
σBO (7.2.2)DIN 28090/DIN 28091 DIN 2505 ASTM
σBO (7.2.2)DIN 28090/DIN 28091 DIN 2505 ASTM
σBO (7.2.2.)DIN 28090/DIN 28091 DIN 2505 ASTM
Die Evaluierung dieser charakteristischenDaten wurde nach den Regeln der DIN28090 durchgeführt. Die Einsatzfähigkeitvon Dichtungen wird durch die Anwendungdieser Werte nicht garantiert. Die Ableitungvon Gewährleistungsansprüchen, gleichwelcher Art, ist aus den genannten Gründennicht möglich. Weiterführende Untersuchun-gen auf diesem Gebiet machen eine zukünf-tige Aktualisierung der Werte möglich bzw.
wahrscheinlich. Wir behalten uns das Rechtfür solche Anpassungen vor.Die Dichtungsfaktoren „m” und „y” nachASME Code wurden bei einer max. Leckratevon1 ml/min. entspricht ca. 0,1 mg/sek. x mnach DIN 28090 bei unterschiedlichenInnendrücken und Flächenpressungengemessen. Die Berechnung nach DIN 2505sowie die „y” und „m” Werte werden künftigdurch andere Regelwerke ersetzt.
Subject to technical alterations.Status: October 2002
KLINGER GmbHP.O. Box 1370, D-65503 IdsteinRich.-Klinger-Straße, D-65510 IdsteinTel +49 (0) 61 26 950-0Fax +49 (0) 61 26 950 340/341e-mail: [email protected]://www.klinger-gmbh.de
Änderungen vorbehalten.Stand: Oktober 2002
KLINGER GmbHPostfach 1370, D-65503 IdsteinRich.-Klinger-Straße, D-65510 IdsteinTel (06126) 950-0Fax (06126) 950340/ 950341e-mail: [email protected]://www.klinger-gmbh.de
![ISOPERIMETRIC ESTIMATES ON SIERPINSKI GASKET TYPE FRACTALS€¦ · discussed in the physical sciences literature under the name \chemical dimension" [HB], and in the mathematics literature](https://static.fdocument.org/doc/165x107/5f976f52ec6fec41746b1c22/isoperimetric-estimates-on-sierpinski-gasket-type-fractals-discussed-in-the-physical.jpg)
