FEATURES DESCRIPTIO U - analog.com · VO Maximum Output RL = 50k ±12.8 ±13.4 ±12.8 ±13.4 V...
12
Click here to load reader
Transcript of FEATURES DESCRIPTIO U - analog.com · VO Maximum Output RL = 50k ±12.8 ±13.4 ±12.8 ±13.4 V...
LT1102
11102fb
■ Slew Rate: 30V/μs■ Gain-Bandwidth Product: 35MHz■ Settling Time (0.01%): 3μs■ Overdrive Recovery: 0.4μs■ Gain Error: 0.05% Max■ Gain Drift: 5ppm/°C■ Gain Nonlinearity: 16ppm Max■ Offset Voltage (Input + Output): 600μV Max
– Drift with Temperature: 2μV/°C■ Input Bias Current: 40pA Max■ Input Offset Current: 40pA Max
– Drift with Temperature (to 70°C): 0.5pA/°C
The LT®1102 is the first fast FET input instrumentationamplifier offered in the low cost, space saving 8-pinpackages. Fixed gains of 10 and 100 are provided withexcellent gain accuracy (0.01%) and non-linearity (3ppm).No external gain setting resistor is required.
Slew rate, settling time, gain-bandwidth product,overdrive recovery time are all improved compared tocompetitive high speed instrumentation amplifiers.
Industry best speed performance is combined withimpressive precision specifications: less than 10pA inputbias and offset currents, 180μV offset voltage. Unlikeother FET input instrumentation amplifiers, on the LT1102there is no output offset voltage contribution to total error,and input bias currents do not double with every 10°C risein temperature. Indeed, at 70°C ambient temperature theinput bias current is only 40pA.
Wideband Instrumentation Amplifierwith ±150mA Output Current
High Speed, Precision,JFET Input Instrumentation Amplifier
(Fixed Gain = 10 or 100)
FEATURES
TYPICAL APPLICATIO
U
DESCRIPTIO
U
Slew Rate
■ Fast Settling Analog Signal Processing■ Multiplexed Input Data Acquisition Systems■ High Source Impedance Signal Amplification from
High Resistance Bridges, Capacitance Sensors,Photodetector Sensors
■ Bridge Amplifier with < 1Hz Lowpass Filtering
APPLICATIO SU
V+ = 15V
LT1102
BIAS
R6
3
5
7
4
8
21
OUTLT1010
V – = –15V
OUTPUT = ±10V INTO 75Ω TO 330kHz (R = 50Ω)±10V INTO 200Ω TO 330kHz (R = 200Ω)DRIVES 2.2nF CAP LOAD
GAIN = 10, DEGRADED 0.01% DUE TO LT1010 LT1102 • TA01
–
+
FPO
5V/D
IV
FPOLT1102 • TA02G = 10 0.5μs/DIV
, LT, LTC and LTM are registered trademarks of Linear Technology Corporation.
LT1102
21102fb
Supply Voltage ...................................................... ±20VDifferential Input Voltage ....................................... ±40VInput Voltage ......................................................... ±20V
Consult LTC Marketing for parts specified with wider operating temperature ranges.
(Note 1)ABSOLUTE AXI U RATI GS
W WW U
PACKAGE/ORDER I FOR ATIOU UW
Output Short-Circuit Duration .......................... IndefiniteOperating Temperature Range
LT1102I .............................................. –40°C to 85°CLT1102AC/LT1102C ................................ 0°C to 70°CLT1102AM/LT1102M (OBSOLETE).....–55°C to 125°C
Storage Temperature Range ................. –65°C to 150°CLead Temperature (Soldering, 10 sec).................. 300°C
TOP VIEW
OUTG = 10
OUTPUT
REFG = 10 +IN
90R
90R RR
9R
9R
V+–IN
V– (CASE)
GROUND(REF)
8
7
6
53
2
1
4
H PACKAGE8-LEAD TO-5 METAL CAN
+–
+–
ORDER PARTNUMBER
LT1102AMHLT1102MHLT1102ACHLT1102CH
LT1102IN8LT1102ACN8LT1102CN8
OUTG = 10
OUTPUT
REFG = 10
+IN
V+
–IN
V–
GROUND(REF) 8
7
6
5
3
2
1
4
TOP VIEW
N8 PACKAGE8-LEAD PDIP
J8 PACKAGE8-LEAD CERDIP
LT1102
90R90R
9 = 1.8k
RR 9R9R
+–
+–
ORDER PARTNUMBER
LT1102MJ8LT1102CJ8
LT1102 • POI01
TJMAX = 100°C, θJA = 130°C/W
OBSOLETE PACKAGEConsider the N8 Package for Alternate Source
OBSOLETE PACKAGEConsider the N8 Package for Alternate Source
Order Options Tape and Reel: Add #TRLead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBFLead Free Part Marking: http://www.linear.com/leadfree/
LT1102
31102fb
LT1102AM/AC LT1102M/I/CSYMBOL PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS
GE Gain Error VO = ±10V, RL = 50k or 2k 0.010 0.050 0.012 0.070 %
GNL Gain Nonlinearity G = 100, RL = 50k 3 14 4 18 ppmG = 100, RL = 2k 8 20 8 25 ppmG = 10, RL = 50k or 2k 7 16 7 30 ppm
VOS Input Offset Voltage 180 600 200 900 μV
IOS Input Offset Current 3 40 4 60 pA
IB Input Bias Current ±3 ±40 ±4 ±60 pA
Input Resistance Common Mode VCM = –11V to 8V 1012 1012 Ω
VCM = 8V to 11V 1011 1011 Ω
Differential Mode 1012 1012 Ω
en Input Noise Voltage 0.1Hz to 10Hz 2.8 2.8 μVP-P
Input Noise Voltage fO = 10Hz 37 37 nV/√HzDensity fO = 1000Hz (Note 2) 19 30 20 nV/√Hz
Input Noise Current fO = 1000Hz, 10Hz (Note 3) 1.5 4 2 5 fA/√HzDensity
lnput Voltage Range ±10.5 ±11.5 ±10.5 ±11.5 V
CMRR Common Mode 1k Source Imbalance, VCM = ±10.5V 84 98 82 97 dBRejection Ratio
PSRR Power Supply VS = ± 9V to ±18V 88 102 86 101 dBRejection Ratio
IS Supply Current 3.3 5.0 3.4 5.6 mA
VO Maximum Output RL = 50k ±13.0 ±13.5 ±13.0 ±13.5 VVoltage Swing RL = 2k ±12.0 ±13.0 ±12.0 ±13.0 V
BW Bandwidth G = 100 (Note 4) 120 220 100 220 kHzG = 10 (Note 4) 2.0 3.5 1.7 3.5 MHz
SR Slew Rate G = 100, VIN = ±0.13V, VO = ±5V 12 17 10 17 V/μsG = 10, VIN = ±1V, VO = ±5V 21 30 18 30 V/μs
Overdrive Recovery 50% Overdrive (Note 5) 400 400 ns
Settling Time VO = 20V Step (Note 4)G = 10 to 0.05% 1.8 4.0 1.8 4.0 μsG = 10 to 0.01% 3.0 6.5 3.0 6.5 μsG = 100 to 0.05% 7 13 7 13 μsG = 100 to 0.01% 9 18 9 18 μs
ELECTRICAL CHARACTERISTICS VS = ±15V, VCM = 0V, TA = 25°C, Gain = 10 or 100, unless otherwise noted.
LT1102
41102fb
LT1102AM LT1102M/ISYMBOL PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS
GE Gain Error G = 100, VO = ±10V, RL = 50k or 2k 0.10 0.25 0.10 0.30 %G = 10, VO = ±10V, RL = 50k or 2k 0.05 0.12 0.06 0.15 %
TCGE Gain Error Drift G = 100, RL = 50k or 2k 9 20 10 25 ppm/°C(Note 6) G = 10, RL = 50k or 2k 5 10 6 14 ppm/°C
GNL Gain Nonlinearity G = 100, RL = 50k 20 70 24 90 ppmG = 100, RL = 2k 28 85 32 110 ppmG = 10, RL = 50k or 2k 9 20 9 24 ppm
VOS Input Offset Voltage 300 1400 400 2000 μV
ΔVOS/ΔT Input Offset Voltage Drift (Note 6) 2 8 3 12 μV/°C
lOS Input Offset Current 0.3 4 0.4 6 nA
IB Input Bias Current ±2 ±10 ±2.5 ±15 nA
CMRR Common Mode VCM = ±10.3V 82 97 80 96 dBRejection Ratio
PSRR Power Supply VS = ±10V to ±17V 88 100 84 99 dBRejection Ratio
IS Supply Current TA = 125°C 2.5 2.5 mA
VO Maximal Output RL = 50k ±12.5 ±13.2 ±12.5 ±13.2 VVoltage Swing RL = 2k ±12.0 ±12.6 ±12.0 ±12.6 V
ELECTRICAL CHARACTERISTICS VS = ±15V, VCM = 0V, Gain = 10 or 100, –55°C ≤ TA ≤ 125°C for AM/M grades,–40°C ≤ TA ≤ 85°C for I grades, unless otherwise noted.
LT1102AC LT1102CSYMBOL PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS
GE Gain Error G = 100, VO = ±10V, RL = 50k or 2k 0.04 0.11 0.05 0.14 % G = 10, VO = ±10V, RL = 50k or 2k 0.03 0.09 0.04 0.12 %
TCGE Gain Error Drift G = 100, RL = 50k or 2k 8 18 9 22 ppm/°C(Note 6) G = 10, RL = 50k or 2k 5 10 6 14 ppm/°C
GNL Gain Nonlinearity G = 100, RL= 50k 8 30 9 40 ppm G = 100, RL= 2k 11 36 12 48 ppm G = 10, RL= 50k or 2k 8 18 8 22 ppm
VOS Input Offset Voltage 230 1000 280 1400 μV
ΔVOS/ΔT Input Offset Voltage Drift (Note 6) 2 8 3 12 μV/°C
IOS Input Offset Current 10 150 15 220 pA
ΔIOS/ΔT Input Offset Current Drift (Note 6) 0.5 3 0.5 4 pA/°C
IB Input Bias Current ±40 ±300 ±50 ±400 pA
ΔIB/ΔT lnput Bias Current Drift (Note 6) 1 4 1 6 pA/°C
CMRR Common Mode VCM = ±10.3V 83 98 81 97 dBRejection Ratio
PSRR Power Supply VS = ±10V to ±17V 87 101 85 100 dBRejection Ratio
IS Supply Current TA = 70°C 2.8 2.9 mA
VO Maximum Output RL = 50k ±12.8 ±13.4 ±12.8 ±13.4 VVoltage Swing RL = 2k ±12.0 ±12.8 ±12.0 ±12.8 V
VS = ±15V, VCM = 0V, Gain = 10 or 100, 0°C ≤ TA ≤ 70°C, unless otherwise noted.
LT1102
51102fb
ELECTRICAL CHARACTERISTICSNote 1: Stresses beyond those listed under Absolute Maximum Ratingsmay cause permanent damage to the device. Exposure to any AbsoluteMaximum Rating condition for extended periods may affect devicereliability and lifetime.Note 2: This parameter is tested on a sample basis only.Note 3: Current noise is calculated from the formula:in = (2qIB)1/2
where q = 1.6 • 10–19 coulomb. The noise of source resistors up to 1GΩswamps the contribution of current noise.
Note 4: This parameter is not tested. It is guaranteed by design and byinference from the slew rate measurement.Note 5: Overdrive recovery is defined as the time delay from the removalof an input overdrive to the output’s return from saturation to linearoperation.50% overdrive equals VIN = ±2V (G = 10) or VIN = ±200mV (G = 100).Note 6: This parameter is not tested. It is guaranteed by design and byinference from other tests.
TYPICAL PERFOR A CE CHARACTERISTICS
UW
Small Signal Response, G = 10(Input = 50mV Pulse)
Small Signal Response, G = 100(Input = 5mV Pulse)
Slew Rate, G = 100(Input = ±130mV Pulse)
Settling Time, G = 10(Input From –10V to 10V)
Settling Time, G = 10(Input From 10V to –10V)
Settling Time, G = 100(Input From –10V to 10V)
2μS/DIV
100m
V/DI
V
FPOLT1102 • TPC01
2μS/DIV
100m
V/DI
V
FPOLT1102 • TPC02
2μS/DIV
5V/D
IVFPOLT1102 • TPC03
2μS/DIV
5mV/
DIV
AT S
UM N
ODE
FPOLT1102 • TPC07
1μS/DIV
5mV/
DIV
AT S
UM N
ODE
FPOLT1102 • TPC04
1μS/DIV
5mV/
DIV
AT S
UM N
ODE
FPOLT1102 • TPC05
2μS/DIV
5mV/
DIV
AT S
UM N
ODE
FPOLT1102 • TPC06
Settling Time, G = 100(Input From 10V to –10V)
LT1102
61102fb
Capacitive Load Handling Output Impedance vs Frequency
TYPICAL PERFOR A CE CHARACTERISTICS
UW
LT1102 • TPC08
CAPACITIVE LOAD (nF)
40OVER
SHOO
T (%
) 80
120
20
60
100
0.1 10 100 10000
1
VS = ±15VTA = 25°C
G = 100
G = 10
LT1102 • TPC09
FREQUENCY (Hz)1k
0.1
OUTP
UT IM
PEDA
NCE
(Ω)
1
10
100
10k 100k 1M
VS = ±15VTA = 25°C
G = 100
G = 10
Gain vs Frequency
Voltage Noise vs FrequencyUndistorted Output vs FrequencyInput Bias Current Over theCommon Mode Range
Common Mode Range vsTemperatureWarm-Up Drift
LT1102 • TPC10
FREQUENCY (Hz)10k
–1.5
GAIN
ERR
OR (%
)
GAIN (dB)
–0.5
0.5
100k 1M 10M
0
–1.0
–1.5
–0.5
–1.0
0
20
30
10
40VS = ±15VTA = 25°C
G = 100
G = 10
LT1102 • TPC11
FREQUENCY (Hz)10k
PEAK
-TO-
PEAK
OUT
PUT
SWIN
G (V
)
20
30
100k 1M 10M0
10
VS = ±15VTA = 25°C
G = 10RL = 2k
G = 10RL = 50k
G = 100RL = 2k OR 50k
LT1102 • TPC12
FREQUENCY (Hz)
RMS
VOLT
AGE
NOIS
E DE
NSIT
Y (n
V√Hz
)
50
40
100
70
30
103 10 30 100 300 1k 3k 10k
20
1/f CORNER = 28Hz
VS = ±15VTA = 25°C
COMMON MODE VOLTAGE (V)–15 –10 0
0.8
INPU
T BI
AS C
URRE
NT, T
A =
125°
C (n
A)
INPUT BIAS CURRENT, TA = 25°C TO 70°C (pA)
1.0
1.4
1.6
1.8
5 10
2.6
1.2
–5 15
2.2
2.0
2.4
–20
0
40
60
80
160
20
120
100
140
LT1102 • TPC13
TA = 25°C
TA = 70°C
TA = 125°C
VS = ±15V
TIME AFTER POWER ON (MINUTES)0
CHAN
GE IN
OFF
SET
VOLT
AGE
(μV)
30
40
50
4
20
10
01 2 3 5
LT1102 • TPC14
VS = ±15VTA = 25°C
N PACKAGE
H AND J PACKAGE
TEMPERATURE (°C)–50
–15
COM
MON
MOD
E RA
NGE
(V)
–14
–12
–11
10
15
12
0 50
–13
13
14
11
100
LT1102 • TPC15
VS = ±15V
G = 10 OR 100
G = 100
G = 10
Supply Current vs Temperature
TEMPERATURE (˚C)–50
SUPP
LY C
URRE
NT (m
A)
4
6
25 75
2
–25 0 50 100 1250
LT1102 • TPC16
VS = ±15V
VS = ±10V
LT1102
71102fb
Short-Circuit Current vs Time Distribution of Offset Voltage
TYPICAL PERFOR A CE CHARACTERISTICS
UW
TEMPERATURE (°C)–50
0
GAIN
ERR
OR (%
)
0.04
0.10
0 50 75
0.02
0.08
0.06
–25 25 100 125
LT1102 • TPC19
VS = ±15VRL ≥ 2k
G = 100
G = 10
Gain Error vs TemperatureGain Nonlinearity OverTemperature
TIME FROM OUTPUT SHORT TO GROUND (MINUTES)0
–50
SHOR
T-CI
RCUI
T CU
RREN
T (m
A)
–40
–20
–10
0
50
20
1 2
–30
30
40
10
3
LT1102 • TPC17
TA = 25°C
TA = 25°C
TA = –55°C
TA = –55°C
TA = 125°C
TA = 125°CVS = ±15V
TEMPERATURE (°C)–50
GAIN
NON
LINE
ARIT
Y (p
pm)
16
40
0 50 75
8
32
24
–25 25 100 125
LT1102 • TPC20
G = 100RL = 2k
G = 100RL = 50k
G = 10RL = 2k OR 50k
INPUT OFFSET VOLTAGE (mV)
0
PERC
ENT
OF U
NITS
5
15
20
25
35
–0.8 0 0.4
10
30
0.8–0.4
LT1102 • TPC18
VS = ±15VTA = 25°C
950 UNITS TESTEDIN ALL PACKAGES
LT1102
81102fb
In the two op amp instrumentation amplifier configura-tion, the first amplifier is basically in unity gain, and thesecond amplifier provides all the voltage gain. In theLT1102, the second amplifier is decompensated for gainof 10 stability, therefore high slew rate and bandwidth areachieved. Common mode rejection versus frequencyis also optimized in the G = 10 mode, because thebandwidths of the two op amps are similar. When G = 100,this statement is no longer true; however, by connectingan 18pF capacitor between pins 1 and 2, a common modeAC gain is created to cancel the inherent roll-off. From200Hz to 30kHz, CMRR versus frequency is improved byan order of magnitude.
Input Protection
Instrumentation amplifiers are often used in harshenvironments where overload conditions can occur.The LT1102 employs FET input transistors, consequentlythe differential input voltage can be ±30V (with ±15Vsupplies, ±36V with ±18V supplies). Some competitiveinstrumentation amplifiers have NPN inputs which areprotected by back-to-back diodes. When the differentialinput Voltage exceeds ±13V on these competitive devices,input current increases to milliampere level; more than±10V differential voltage can cause permanent damage.
When the LT1102 inputs are pulled below the negativesupply or above the positive supply, the inputs will clampa diode voltage below or above the supplies. No damagewill occur if the input current is limited to 20mA.
Common Mode Rejection Ratiovs Frequency
Gains Between 10 and 100
Gains between 10 and 100 can be achieved by connectingtwo equal resistors (= RX) between pins 1 and 2 and pins7 and 8.
The nominal value of R is 1.84kΩ. The usefulness of thismethod is limited by the fact that R is not controlled tobetter than ±10% absolute accuracy in production.However, on any specific unit, 90R can be measuredbetween Pins 1 and 2.
APPLICATIO S I FOR ATIO
WU UU
Gain = 10 +RX
R + RX/90
FREQUENCY (Hz)1
0
COM
MON
MOD
E RE
JECT
ION
RATI
O (d
B)
20
40
60
80
120
10 100 1k 10k 100k 1M
100
LT1102 • AI01
VS = ±15VTA = 25°C
G = 10018pF PIN 1TO PIN 2
G = 10
G = 100
LT1102
91102fb
Gain = 20, 110, or 200 Instrumentation Amplifiers
Differential Output
Multiplexed Input Data Acquisition
Single Ended Output
Voltage Programmable Current Source is Simple and Precise Dynamic Response of the Current Source
APPLICATIO S I FOR ATIO
WU UU
LT1102 • AI03
OUTPUT
AO A1
DECODER
EN
509 OREQUIVALENT
S1A4 CHANNELS
OFDIFFERENTIAL
INPUT
S4A
S1B
S4B
–
+LT1102
DA
800kHz SIGNALS CAN BE MULTIPLEXED WITH LT1102 IN G = 10
DB
HORIZ. = 20μs/DIV
A = 5V/DIV
FPOLT1102 • AI05
B = 5mA/DIV–
+
LT1102 • AI04
LT1006
–
+LT1102A = 100
0.05μF
10k
LOAD
0 ±10V
IK
VIN
IK =VIN
R • 100R10Ω*
LT1102 • AI02
8
6
3
8
1
6
3
OUT
–
+IN
GAIN = 200, AS SHOWNGAIN = 20, SHORT PIN 1 TO PIN 2, PIN 7 TO PIN 8 ON BOTH DEVICESGAIN = 110, SHORT PIN 1 TO PIN 2, PIN 7 TO PIN 8 ON ONE DEVICE,NOT ON THE OTHERINPUT REFERRED NOISE IS REDUCED BY √2 (G = 200 OR 20)
–
+LT1102
–
+LT1102
8
1
1
6
3
8
1
6
3 –
+LT1102
–
+IN
–
+OUT
–
+LT1102
LT1102
101102fb
Basic Connections
Offset NullingSettling Time Test Circuit
TYPICAL APPLICATIO S
U
INPUT
65
8
7
41
2NC
NC
V –
V+
REF
3OUT
GAIN = 100
INPUT
65
8
7
41
2V –
V+
REF
3OUT
GAIN = 10 LT1102 • TA03
LT1102
–
+
LT1102
–
+
1
8
56
3
4
15V
–15V
R1
5.0k
5.1k
FET PROBE
HP5082-2810
20VP-PFLAT-TOP INPUT
LT1102 • TA04
LT1102
–
+
200Ω
R1 = 910Ω, G = 10R1 = 10k, G = 100
100Ω
6
3
4
1
8
5
15V
–15V
2k
R2
OUT
2k
10k1.8k
LT1102 • TA05
LT1102
–
+
R2 = 3.3Ω, G = 10R2 = 30Ω, G = 100NULL RANGE = ±1mVGAIN DEGRADATION ≈ 0.018%
LT1102
111102fb
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-tation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
U
PACKAGE DESCRIPTIO
J8 Package8-Lead CERDIP (Narrow .300 Inch, Hermetic)
(Reference LTC DWG # 05-08-1110)
OBSOLETE PACKAGES
.050(1.270)
MAX
.016 – .021**(0.406 – 0.533)
.010 – .045*(0.254 – 1.143)
SEATINGPLANE
.040(1.016)
MAX .165 – .185(4.191 – 4.699)
GAUGEPLANE
REFERENCEPLANE
.500 – .750(12.700 – 19.050)
.305 – .335(7.747 – 8.509)
.335 – .370(8.509 – 9.398)
DIA
.230(5.842)
TYP
.027 – .045(0.686 – 1.143)
.028 – .034(0.711 – 0.864)
.110 – .160(2.794 – 4.064)
INSULATINGSTANDOFF
45°TYP
H8 (TO-5) 0.230 PCD 0801
LEAD DIAMETER IS UNCONTROLLED BETWEEN THE REFERENCE PLANE AND THE SEATING PLANE
FOR SOLDER DIP LEAD FINISH, LEAD DIAMETER IS.016 – .024
(0.406 – 0.610)
*
**
PIN 1
J8 0801
.014 – .026(0.360 – 0.660)
.200(5.080)
MAX
.015 – .060(0.381 – 1.524)
.1253.175MIN
.100(2.54)BSC
.300 BSC(7.62 BSC)
.008 – .018(0.203 – 0.457)
0° – 15°
.005(0.127)
MIN
.405(10.287)
MAX
.220 – .310(5.588 – 7.874)
1 2 3 4
8 7 6 5
.025(0.635)
RAD TYP.045 – .068
(1.143 – 1.650)FULL LEAD
OPTION
.023 – .045(0.584 – 1.143)
HALF LEADOPTION
CORNER LEADS OPTION (4 PLCS)
.045 – .065(1.143 – 1.651)NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE
OR TIN PLATE LEADS
H Package8-Lead TO-5 Metal Can (.230 Inch PCD)
(Reference LTC DWG # 05-08-1321)
LT1102
121102fb
Linear Technology Corporation1630 McCarthy Blvd., Milpitas, CA 95035-7417(408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com
LT 0507 REV B • PRINTED IN USA
© LINEAR TECHNOLOGY CORPORATION 1991
U
PACKAGE DESCRIPTION8 Package
8-Lead PDIP (Narrow .300 Inch)(Reference LTC DWG # 05-08-1510)
N8 1002
.065(1.651)
TYP
.045 – .065(1.143 – 1.651)
.130 ± .005(3.302 ± 0.127)
.020(0.508)
MIN.018 ± .003(0.457 ± 0.076)
.120(3.048)
MIN
1 2 3 4
8 7 6 5
.255 ± .015*(6.477 ± 0.381)
.400*(10.160)
MAX
.008 – .015(0.203 – 0.381)
.300 – .325(7.620 – 8.255)
.325+.035–.015+0.889–0.3818.255( )
NOTE:1. DIMENSIONS ARE
INCHESMILLIMETERS
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm)
.100(2.54)BSC
