ZANUSSI BST6A ΦΟΥΡΝΟΣ

8/3/2019 ZANUSSI BST6A

1/14


2/14


3/14


4/14


5/14


6/14


7/14


8/14


9/14


10/14

11

The Oven Door GasketThe correct operation of the oven is ensured by a gasketplaced round the edge of the oven cavity.

Periodically check the condition of this gasket. Ifnecessary, clean it without using abrasive cleaningproducts.

If the gasket shows to be damaged, call you localZanussi Service Centre. Do not use the oven until ithas been repaired.

The Hinged GrillThis model has been fitted with a hinged grill element,to enable you to clean the roof of the oven easily.

Before proceeding, ensure the oven is isolated fromthe electricity supply. Then undo the screw which holdsthe grill in place. (see Fig. 10)Gently pull the grill downward to allow access to theoven roof. (see Fig. 11).Clean the oven roof with a suitable cleaner and wipe

dry before replacing the hinged grill element.Gently push up the grill element into place and firmlyscrew into place the holding nut.

NOTE: Ensure the grill holding nut is firmly in placeto avoid the grill falling down during operation.

FO O781

FO O778

Grease Filter

When cooking meat, the grease filter must be fittedover the oven fan by clipping it over the vents in theback panel. This will prevent a built-up of fat on the fanimpellor. Do not use abrasive materials to clean theseal. The grease filter is dishwasher proof.

When cooking is completed and the oven has cooleddown, remove the filter by pushing the protrudingtongue on the filter upward. (See Fig. 12)

Fig. 12

FO 0018

Fig. 10

Fig. 11


11/14


12/14

13

If after the checks listed in the previous chapter, theappliance still does not work correctly, contact yourlocals Zanussi Service Centre, specifying the type ofmalfunctioning, the appliance model (Mod.), the

product number (Prod. No.) and the serial number(Ser. No.) marked on the identification plate.This plate is placed on the front external edge of theoven cavity, as indicated in Fig. 14.

Original spareparts,certified by the productmanufacturer andcarrying this symbol areonly available at ourService Centre andauthorized sparepartsshops.

You new appliance is under guarantee. You will findattached here the guarantee certificate. If it is missing,ask for it to your retailer, stating the date of purchase,the model number and the serial number marked onthe appliance's identification plate.

Keep the guarantee certificate with the proof ofpurchase, and show them at the request of our techicalpersonnel, otherwise they will have to make a charge.

8. Techical Assistance and Spare Parts

9. Guarantee

Fig. 14

The Zanussi Service Force, through its numerousauthorized centres, provides assistance to the mostimportant brands of electrical domestic appliances. Ifnecessary, contact the nearest Centre by consulting thetelephone directory under the name Zanussi, or theyellow pages in the section Electrical Domestic Applaines/Repair.

SER.NO.

Mod.

PROD.NO.

SER. NO.

Mod.

PROD.NO.

FO1147


13/14

14

10. Technical Data

Recessin coloumn: 580 mm

dimensions height { undertop: 591 mmwidth 560 mmdepth 550 mm

Internal height 325 mmoven width 440 mmdimensions depth 390 mm

oven capacity 53 l.

Oven ratings

Top-Bottom heating elements 2000 W

Grill element 1800 W

Fan ducted oven element 2500 W

Oven light 15 W

Cooling fan 20 W

Convection fan 30 W

Total rating 2570 W

Electric rate (50Hz) 230 V

11. Installation

Fig. 15 - Oven Dimensions

Fig. 16 - Coloumn Built-in Recess Dimlensions

Fig. 17 - Undertop Built-in Recess Dimensions

Building In

It is important that the dimensions and materials of thesurround or cabinet into which the oven will be built arecorrect and will withstand a temperature increase.A correct installation will have to ensure a properprotection against contact with electric parts or merely

functionally isolated parts.All the units meant to ensure protection have to be fitted

not to be taken away without using any tool.We recommed not to install the appliance nearrefrigerators or freezer, since the heat could affect theperformance of these appliances.

FO 0414 FO 0292

FO 0276


14/14

15

Terminal block

The oven has an easily accessible terminal block,which is meant to work with an electric single-phaserate of 220-230 V.

(Fig. 20)

The manufacturer disclaims any

responsability should all the safetymeasures not be carried out.

Fig. 20

Fig.19

Fig. 18

Securing the Oven to the Cabinet

Fit the appliance into the cabinet recess.Open teh oven door and secure the oven to the kitchencabinet with four wood screws, which fit the holesprovided in the oven frame (Fig.18-19).When installing an electric plate hob over the oven, thehob's electrical connection and the oven's one have tobe carried out separately, for security reasons and to letthe oven be taken off the unit easier, if necessary.

Electric Connection

Before the appliance is connected:

1) check that the main fuse and the domestic installationcan support the load;

2) check that the power supply is properly earthed incompliance with the current rules;

3) check the socket or the double pole switch used forthe electrical connection can be easily reached withthe appliance built in the forniture unit.

The appliance is supplied with a connection cable. Thishas to be provided with a proper plug, able to support theload marked on the identification plate. The plug has tobe fitted in a proper socket.

If connecting the appliance directly to the electric system,it is necessary that you install a double pole switchbetween the appliance and the electricity supply, with aminimum gap of 3 mm. between the switch contacts andof a type suitable for the required load in compliancewith the current rules.The connection cable has to be placed in order that, ineach part, it cannot reach a temperature 50 C higher

than the room temperature.After the connection is carried out, test the heatingelements for about 3 minutes.

FO 0039

FO 0986

FO 0279

ZANUSSI BST6A ΦΟΥΡΝΟΣ

Documents

Transcript of ZANUSSI BST6A ΦΟΥΡΝΟΣ