St type Implant - Brain Base · Φ1.9mm Φ2.1mm Φ2.5mm Φ4.0mm series Φ4.3mm series Φ5.0mm...
Transcript of St type Implant - Brain Base · Φ1.9mm Φ2.1mm Φ2.5mm Φ4.0mm series Φ4.3mm series Φ5.0mm...
St‐type Implant
BBC Implant
St‐type Implant
Platform changing
Reverse taper
Fine edge
Internal 8゚ Morse taper
Internal HEX connection
Φ 1.9mm Φ 2.1mm Φ 2.5mm
Φ 4.0mm series Φ 4.3mm series Φ 5.0mm series
St4008SSt4010SSt4012SSt4014S
St4308SSt4310SSt4312SSt4314S
St5008SSt5010SSt5012S
Φ 4.0mm Φ 4.0mm
Φ 4.0mm Φ 5.0mmΦ 4.3mm
Φ 4.0mm
*The diameter of the implant-abutment connecting part is φ 3.5mm.
St‐type Implant
Drilling Sequences
* Do drilling 1.0mm deeper than the full length of an Implant.
In case of St4010S
Soft Bone(Type IV)
Normal Bone(Type III-II)
Hard Bone(Type I)
● St4008S: Drilling length=4mm ● St4010S: Drilling length=6mm● St4012S: Drilling length=8mm ● St4014S: Drilling length=10mm
Drilling Rotation 1000rpm 800rpm 500rpm 500rpm
▲ This step can skip over in case of Hard Bone.
Drilling Sequences
Guide Drill 20Spiral Drill 25Spiral Drill 28Spiral Drill 32Spiral Drill 35Spiral Drill 38Spiral Drill 41Spiral Drill 45
Guide Drill 20Spiral Drill 25Spiral Drill 28Spiral Drill 32Spiral Drill 35Spiral Drill 38
Guide Drill 20Spiral Drill 25Spiral Drill 28Spiral Drill 32St50**S
Guide Drill 20Spiral Drill 25Spiral Drill 28Spiral Drill 32Spiral Drill 35Spiral Drill 38
Guide Drill 20Spiral Drill 25Spiral Drill 28Spiral Drill 32
Guide Drill 20Spiral Drill 25
St43**S
Guide Drill 20Spiral Drill 25Spiral Drill 28Spiral Drill 32Spiral Drill 35
Guide Drill 20Spiral Drill 25Spiral Drill 28
Guide Drill 20
St40**S
Hard Bone(Type I)
Normal Bone(TypeIII-II)
Soft Bone(TypeIV)
St-typeImplant
* Do drilling 1.0mm deeper than the full length of an Implant.
● Do drilling 4.0mm shorter than the full length of an Implant.
Drilling SequencesIn case of St4310S
Soft Bone(Type IV)
Normal Bone(Type III-II)
Hard Bone(Type I)
● St4308S: Drilling length=4mm ● St4310S: Drilling length=6mm● St4312S: Drilling length=8mm ● St4314S: Drilling length=10mm
* Do drilling 1.0mm deeper than the full length of an Implant.
Drilling Rotation 1000rpm 800rpm 500rpm 500rpm 500rpm
▲ This step can skip over in case of Hard Bone.
Drilling SequencesIn case of St5010S
Soft Bone(Type IV)
Normal Bone(Type III-II)
Hard Bone(Type I)
* Do drilling 1.0mm deeper than the full length of an Implant.
● St5008S: Drilling length=4mm ● St5010S: Drilling length=6mm● St5012S: Drilling length=8mm
Drilling Rotation 1000rpm 800rpm 500rpm 500rpm 500rpm
▲ This step can skip over in case of Hard Bone.