OAA160 R4 4 - rtellason.comrtellason.com/chipdata/oaa160.pdf · DS-OAA160-R4.4 1 OAA160 Dual Pole...
Click here to load reader
Transcript of OAA160 R4 4 - rtellason.comrtellason.com/chipdata/oaa160.pdf · DS-OAA160-R4.4 1 OAA160 Dual Pole...
www.clare.comDS-OAA160-R4.4 1
OAA160Dual Pole OptoMOS® Relays
Part # DescriptionOAA160 8 Pin DIP (50/Tube)OAA160P 8 Pin Flatpack (50/Tube)OAA160PTR 8 Pin Flatpack (1000/Reel)OAA160S 8 Pin Surface Mount (50/Tube)OAA160STR 8 Pin Surface Mount (1000/Reel)
OAA160 UnitsLoad Voltage 250 VLoad Current 50 mAMax RON 100 Ω
Applications
Features
Description
Approvals
Ordering Information
Pin Configuration
Switching Characteristics ofNormally Open (Form A) Devices
CONTROL
LOAD
10ms
10% 10%
90%
+
TONTOFF
+
+
• Telecommunications• Telecom Switching• Tip/Ring Circuits• Modem Switching (Laptop, Notebook, Pocket
Size)• Hookswitch• Dial Pulsing• Ground Start• Ringing Injection
• Instrumentation• Multiplexers• Data Acquisition• Electronic Switching• I/O Subsystems• Meters (Watt-Hour, Water, Gas)
• Medical Equipment-Patient/Equipment Isolation• Security• Aerospace• Industrial Controls
• Small 8 Pin DIP Package• Low Drive Power Requirements (TTL/CMOS
Compatible)• No Moving Parts• High Reliability• Arc-Free With No Snubbing Circuits• 3750VRMS Input/Output Isolation• No EMI/RFI Generation• Machine Insertable, Wave Solderable• Surface Mount and Tape & Reel
Versions Available
OAA160 is a 250V, 50mA, 20Ω dual 1-Form-A relay.This high performance product provides the fastest(0.125ms) switching available for two independentForm-A relays in a single package.
• UL Recognized: File Number E76270• CSA Certified: File Number LR 43639-10• Certified to:
• EN 60950• EN 41003
1
2
3
4
8
7
6
5
AC/DC Configuration
OAA160 Pinout
+ Control - Pole #1
– Control - Pole #1
+ Control - Pole #2
– Control - Pole #2
Normally Open - Pole #1
Normally Open - Pole #2
www.clare.com2
OAA160
Rev. 4.4
Parameter Conditions Symbol Min Typ Max Units
Output Characteristics @ 25°C
Load Voltage (Peak) - VL - - 250 VLoad Current* (Continuous)
AC/DC Configuration - IL - - 50 mAPeak Load Current 10ms ILPK - - 100 mAOn-Resistance
AC/DC Configuration IL=50mA RON - 50 100 ΩOff-State Leakage Current VL=250V ILEAK - - 0.025 µASwitching Speeds
Turn-On IF=10mA, VL=10V TON - - 0.125 msTurn-Off IF=10mA, VL=10V TOFF - - 0.125 ms
Output Capacitance 50V; f=1MHz COUT - 5 - pFInput Characteristics @ 25°C
Input Control Current IL=50mA IF 10 - 50 mAInput Dropout Current - IF 0.4 0.7 - mAInput Voltage Drop IF=10mA VF 0.9 1.2 1.4 VReverse Input Current VR=5V IR - - 10 µAInput to Output Capacitance - CI/O - 3 - pF*NOTE: If both poles operate simultaneously load current must be derated so as not to exceed the package power dissipation value.
Parameter Min Typ Max Units
Input Power Dissipation - - 1501 mWInput Control Current - - 50 mA
Peak (10ms) - - 1 AReverse Input Voltage - - 5 VTotal Power Dissipation - - 8002 mWIsolation Voltage
Input to Output 3750 - - VRMS
Soldering TemperatureDIP Package - - +260 °CSurface Mount Package - - +220 °C(10 Seconds Max.)
Operational Temperature -40 - +85 °CStorage Temperature -40 - +125 °C1 Derate Linearly 1.33 mw/˚C2 Derate Linearly 6.67 mw/˚C
Absolute Maximum Ratings are stress ratings. Stresses inexcess of these ratings can cause permanent damage tothe device. Functional operation of the device at conditionsbeyond those indicated in the operational sections of thisdata sheet is not implied.
Absolute Maximum Ratings (@ 25˚ C)
Electrical Characteristics
OAA160
www.clare.com 3Rev. 4.4
PERFORMANCE DATA*
The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our applicationdepartment.
OAA160Typical On-Resistance Distribution(N=50 Ambient Temperature = 25°C)
(Load Current = 50mADC; IF = 10mADC)35
30
25
20
15
10
5
042.5 44.5 46.5 47.543.5 45.5
On-Resistance (Ω)
Dev
ice
Co
un
t (N
)
OAA160Typical LED Forward Voltage Drop
(N=50 Ambient Temperature = 25°C)IF = 10mADC
35
30
25
20
15
10
5
01.17 1.19 1.21 1.23 1.25
LED Forward Voltage Drop (V)
Dev
ice
Co
un
t (N
)
OAA160Typical Blocking Voltage Distribution(N=50 Ambient Temperature = 25°C)
35
30
25
20
15
10
5
0367.5 381.5 395.5 402.5374.5 388.5
Blocking Voltage (V)
Dev
ice
Co
un
t (N
)
OAA160Typical IF for Switch Operation
(N=50 Ambient Temperature = 25°C)(Load Current = 50mADC)
2.075 2.9751.625 2.525 3.425 3.875
LED Current (mA)
Dev
ice
Co
un
t (N
)
25
20
15
10
5
0
OAA160Typical IF for Switch Dropout
(N=50 Ambient Temperature = 25°C)(Load Current = 50mADC
25
20
15
10
5
02.075 2.9751.625 2.525 3.425 3.875
LED Current (mA)
Dev
ice
Co
un
t (N
)
)
OAA160Typical Leakage vs. Temperature
(Measured across Pins 5 & 6 or 7 & 8)
Temperature (°C)
Lea
kag
e (µ
A)
-40
0.014
0.012
0.010
0.008
0.006
0.004
0.002
0-20 0 20 40 60 80 100
OAA160Typical Turn-On Time
(N=50 Ambient Temperature = 25°C)(Load Current = 50mADC; IF = 10mADC)
0.05 0.09 0.13 0.150.07 0.11
Turn-On (ms)D
evic
e C
ou
nt
(N)
30
25
20
15
10
5
0
OAA160Typical Turn-Off Time
(N=50 Ambient Temperature = 25°C)(Load Current = 50mADC; IF = 10mADC)
0.012 0.022 0.032 0.0370.0270.017
Turn-Off (ms)
Dev
ice
Co
un
t (N
)
25
20
15
10
5
0
OAA160Typical Load Current vs. Temperature
Temperature (°C)
Lo
ad C
urr
ent
(mA
)
100
90
80
70
60
50
40
30
20
10
0-40 -20 0 20 40 60 80 120100
30mA20mA10mA
OAA160Typical Blocking Voltage vs. Temperature
Temperature (°C)
Blo
ckin
g V
olt
age
(VR
MS)
-40
400
395
390
385
380
375
370
365-20 0 20 40 60 80 100
OAA160Typical Turn-On vs. Temperature
(Load Current = 50mADC)
Temperature (°C)
10mA
20mA
Tu
rn-O
n (
ms)
-40
1.50
1.25
1.00
0.75
0.50
0.25
0-20 0 20 40 60 80 100
OAA160Typical Turn-Off vs. Temperature
(Load Current = 50mADC)
Temperature (°C)
Tu
rn-O
ff (
ms)
-40
0.0500.0450.0400.0350.0300.0250.0200.0150.0100.005
0-20 0 20 40 60 80 100
10mA
www.clare.com4
OAA160
Rev. 4.4
PERFORMANCE DATA*
The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our applicationdepartment.
OAA160Typical Turn-On vs. LED Forward Current
(Load Current = 50mADC)
LED Forward Current (mA)
Tu
rn-O
n (
ms)
0 5 10 15 20 25 30 35 40 45
0.18
0.16
0.14
0.12
0.10
0.08
0.06
0.04
0.02
050
OAA160Typical LED Forward Voltage Drop
vs. Temperature
Temperature (°C)
LE
D F
orw
ard
Vo
ltag
e D
rop
(V
) 1.8
1.6
1.4
1.2
1.0
0.8-40 -20 0 20 40 60 80 120100
50mA30mA20mA10mA5mA
OAA160Typical Turn-Off vs. LED Forward Current
(Load Current = 50mADC)
LED Forward Current (mA)
Tu
rn-O
ff (
ms)
0 5 10 15 20 25 30 35 40 45 50
0.040
0.035
0.030
0.025
0.020
0.015
OAA160Typical On-Resistance vs. Temperature(Load Current = 50mADC; IF = 10mADC)
Temperature (°C)
On
-Res
ista
nce
(Ω
)
-40
70
60
50
40
30
20
10
0-20 0 20 40 60 80 100
OAA160Typical IF for Switch Operation
vs. Temperature(Load Current = 50mADC)
Temperature (°C)
LE
D C
urr
ent
(mA
)
-40
5.000
4.500
4.000
3.500
3.000
2.500
2.000
1.500
1.000
0.500
0-20 0 20 40 60 80 100
OAA160Typical IF for Switch Dropout
vs. Temperature
Temperature (°C)L
ED
Cu
rren
t (m
A)
-40
5.0004.5004.0003.5003.0002.5002.0001.5001.0000.500
0-20 0 20 40 60 80 100
OAA160Typical Load Current vs. Load Voltage
(Ambient Temperature = 25°C)IF = 10mADC
Load Voltage (V)
Lo
ad C
urr
ent
(mA
)
50
40
30
20
10
0
-10
-20
-30
-40
-50-3 -2 -1 0 1 2 3
OAA160Energy Rating Curve
Time
Lo
ad C
urr
ent
(A)
10µs
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
01ms100µs 100ms 1s10ms 10s 100s
OAA160
www.clare.com 5Rev. 4.4
Dimensionsmm
(inches)
MECHANICAL DIMENSIONS
4.445 ± 0.127(0.175 ± 0.005)
3.302(0.130)
7.620 ± 0.254(0.300 ± 0.010)
6.350 ± 0.127(0.250 ± 0.005)
8.077 ± 0.127(0.318 ± 0.005)
2.540 ± 0.127(0.100 ± 0.005)
9.525 ± 0.254(0.375 ± 0.010)
0.457 ± 0.076(0.018 ± 0.003)
0.254 TYP.(0.010 TYP.)
0.635 TYP.(0.025 TYP.)
8 Pin DIP Surface Mount (“S” Suffix)9.652 ± 0.381(0.380 ± 0.015)
PC Board Pattern (Top View)
6.350 ± 0.127(0.250 ± 0.005)
2.540 ± 0.127(0.100 ± 0.005)
7.620 ± 0.127(0.300 ± 0.005)
7.620 ± 0.127(0.300 ± 0.005)
8-0.800 DIA.(8-0.031 DIA.)
7.239 TYP.(0.285 TYP.)
3.302(0.130)
7.620 ± 0.254(0.300 ± 0.010)
9.144 TYP.(0.360 TYP.)
6.350 ± 0.127(0.250 ± 0.005)
9.652 ± 0.381(0.380 ± 0.015)
2.540 ± 0.127(0.100 ± 0.005)
9.144 ± 0.508(0.360 ± 0.020)
0.457 ± 0.076(0.018 ± 0.003)
8.077 ± 0.127(0.318 ± 0.005 )
8 Pin DIP Through Hole (Standard)
PC Board Pattern (Top View) 2.540 ± 0.127
(0.100 ± 0.005)
8.305 ± 0.127(0.327 ± 0.005)
1.905 ± 0.127(0.075 ± 0.005)
1.498 ± 0.127(0.059 ± 0.005)
PC Board Pattern (Top View)
2.540 ± 0.127(0.100 ± 0.005)
8.763 ± 0.127(0.345 ± 0.005)
1.193(0.047)
0.787(0.031)
8 Pin Flatpack (“P” Suffix)
7.620 ± 0.254(0.300 ± 0.010)
2.159 TYP.(0.085 TYP.)
2.286 MAX.(0.090 MAX.)
9.398 ± 0.127(0.370 ± 0.005)
6.350 ± 0.127(0.250 ± 0.005)
9.652 ± 0.381(0.380 ± 0.015)
2.540 ± 0.127(0.100 ± 0.005)
8.077 ± 0.127(0.318 ± 0.005)
0.457 ± 0.076(0.018 ± 0.003)
0.203(0.008)
0.635 ± 0.127(0.025 ± 0.005)
Clare, Inc. makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptionsat any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in Clare’s Standard Terms and Conditions of Sale, Clare, Inc. assumes no liability whatsoever, anddisclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.
The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to sup-port or sustain life, or where malfunction of Clare’s product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. Clare, Inc. reserves the right to discontinue ormake changes to its products at any time without notice.
Specification: DS-OAA160-R4.4©Copyright 2003, Clare, Inc.OptoMOS® is a registered trademark of Clare, Inc.All rights reserved. Printed in USA.1/23/03
For additional information please visit our website at: www.clare.com
Dimensionsmm
(inches)
MECHANICAL DIMENSIONS
Tape and Reel Packaging for 8 Pin Flatpack Package
User Direction of FeedEmbossment
Embossed Carrier
Top CoverTape Thickness0.102 MAX.(0.004 MAX.)
330.2 DIA.(13.00 DIA.)
1 8
K1= 2.00(0.079)
Top CoverTape
K0= 2.70(0.106)
P = 12.00(0.472)
W = 16.30 max(0.642 max)
Bo = 10.30(0.406)
Ao = 10.30(0.406)
NOTE: Tape dimensions not shown, comply with JEDEC Standard EIA-481-2
Tape and Reel Packaging for 8 Pin Surface Mount Package
K1= 4.2
(0.165)
Top CoverTape
P = 12.00(0.472)
User Direction of Feed
W = 16.30 max(0.642 max)
Bo = 10.30(0.406)
Embossment
Embossed Carrier
Top CoverTape Thickness0.102 MAX.(0.004 MAX.)
Ao = 10.30(0.406)
330.2 DIA.(13.00 DIA.)
1 8
K0= 4.90(0.193)
NOTE: Tape dimensions not shown, comply with JEDEC Standard EIA-481-2