Contact Area : 50μ” Gold

Spec No.

GTD0001-00

Update Date

2015/7/14

Revision

E

UDE P/N：

10G Base-T

LED:L-Green;R-Green

Description： RJ45 1x1 Table Up

To：

Customer P/N：

Through Hole

GTD-1C00VS14

Approved Checked Prepared

Spec No. : GTD0001-00 GTD-1C00VS14

1. MECHANICAL DIMENSION

1.1 Product Dimension

www.ude-corp.com

General Tolerance :X.X :

X.XX :

± 0.38

± 0.20

- 1 -

Spec No. : GTD0001-00 GTD-1C00VS14

1.2 Recommended PCB Layout

Component Side of Board

All dimension tolerance are ±0.05mm unless otherwise specified

www.ude-corp.com- 2 -

Spec No. : GTD0001-00 GTD-1C00VS14

1.3 Panel Cutout

www.ude-corp.com- 3 -

Spec No. : GTD0001-00 GTD-1C00VS14

1.4

- All dimensions follow :

FCC subpart F, 68,500, Figure (C)(2)(i) & (C)(2)(ii) & (C)(3)(i)

IEC 60603-7

- All plugs must be meeting the requirements of plug Go & No-Go gauge.

Gauge follow : FCC subpart F, 68,500, Figure (C)(4)(i) & (C)(5)(i)

- There must be no damage to Housing and Locking Latch.

- There must be no nicks and cuts in cable.

- Durability : 750 cycles generally

www.ude-corp.com

Standard RJ45 Plug Specification

- 4 -

Spec No. : GTD0001-00 GTD-1C00VS14

2. REQUIREMENTS

2.1 Design and Construction

2.2 Material

2.2.1 Terminal Parts ( Terminal：Underplating :50μ" min. Nickel overall )

2.2.1.1 RJ Terminal : PH. Bronze, Thickness=0.30mm

Finish : Contact Area :50μ" Gold

Solder Tail : 120μ" min. Mt.Tin

2.2.1.3 Input Terminal : Brass, Thickness=0.35mm

Finish : 120μ" min. Mt.Tin

2.2.1.4 Module Terminal : Brass, Thickness=0.30mm

Finish : 120μ" min. Tin

2.2.2 Plastic Parts <UL94V-0>

2.2.2.1 Housing : LCP, Black

2.2.2.2 Case : PA6T, Black

2.2.2.3 Spacer : PA6T,Black

2.2.3 Shield Parts

2.2.3.1 Shield : Stainless steel, Thickness=0.20mm, Pre-soldering

www.ude-corp.com- 5 -

Product shall be of design, construction and physical dimensions specified

on applicable.

Spec No. : GTD0001-00 GTD-1C00VS14

2.3 Operating and Storage Temperature

2.4 RJ45 specifications

2.5 Performance and Test Description

2.6 Packaging and Packing

www.ude-corp.com

Operating Temperature :

44N max

Insulation Resistance :

Locking Force of Plug Latch :

Storage Temperature :

Product is designed to meet electrical, mechanical and environmental

performance requirements specified in below table. All tests are performed

at ambient environmental conditions per MIL-STD-1344A and EIA-364

unless otherwise specified.

All parts shall be packaged and packed to protect against physical

damage、corrosion and deterioration during shipment and storage.

2500 cycles

500MΩ min.

Durability :

50N min. @ 60+/-5 sec

- 6 -

Removal force with the latch depressed :

0°C to +70°C

Insertion force with the latch depressed : 22N max

-40°C to +85°C

Spec No. : GTD0001-00 GTD-1C00VS14

3. ELECTRICAL CHARACTERISTICS

3.1 Schematic

www.ude-corp.com

Green

Emitting Color λp (nm) Vf @If=20mA Ir @Vr=5V

- 7 -

565 1.7 ~2.6 V 10μA max.

INPUT RJ45 OUTPUT

C1 TRP1+

C2 TRP1-

C3 TRP2+

C6 TRP2-

C4 TRP3+

C5 TRP3-

C7 TRP4+

C8 TRP4-

2KV 1000pF

Shield

300Ω

75Ω

75Ω

75Ω

1 : 1

1 : 1

1 : 1

1 : 1

TRD1+ R8 TRCT1 R7 TRD1- R9

TRD2+ R2 TRCT2 R1 TRD2- R3

TRD3+ R4 TRCT3 R6 TRD3- R5

TRD4+ R10 TRCT4 R12 TRD4- R11

1 : 1 IET+ R13

IET- R14 IETCT R15

Green

L1

L2

Green

L3

L4

Spec No. : GTD0001-00 GTD-1C00VS14

3.2 Transmitter filter & Receiver filter

Type : Balance low pass 100Ω impedance

Insertion Loss

5MHZ -0.55 dB Max

200MHZ -0.77 dB Max

400MHZ -1.41 dB Max

3.3 Return Loss

100MHz -24 dB Min load 100Ω

200MHz -18 dB Min load 100Ω

300MHz -15 dB Min load 100Ω

400MHz -10 dB Min load 100Ω

500MHz - 8 dB Min load 100Ω

3.4 Reflected CM to Diff Conversion(REF)

50MHZ -30 dB Min

100MHZ -27 dB Min

200MHZ -24 dB Min

300MHZ -22 dB Min

400MHZ -21 dB Min

500MHZ -20 dB Min

www.ude-corp.com- 8 -

Spec No. : GTD0001-00 GTD-1C00VS14

3.5 Reflected Diff to CM Conversion(REF)

1MHZ -48 dB Min

100MHZ -35 dB Min

400MHZ -24 dB Min

500MHZ -24 dB Min

3.6 CM to DM Conversion(REF)

50MHZ -48 dB Min

100MHZ -42 dB Min

200MHZ -36 dB Min

300MHZ -33 dB Min

400MHZ -30 dB Min

500MHZ -28 dB Min

3.7 CM to CM Attenuation

1MHZ -22 dB Min

500MHZ -20 dB Min

800MHZ -20 dB Min

1000MHZ -17 dB Min

3.8 Cross Talk

1 MHz -34 dB Min

350 MHz -23 dB Min

500 MHz -23 dB Min

www.ude-corp.com- 9 -

Spec No. : GTD0001-00 GTD-1C00VS14

3.9 5th channel common mode pick up

Line side D CM to PHY side E diff: 1-400MHz - 7dB Max

( must be between 0dB and -7dB)

3.10 Inductance @ 100KHz, 0.1V 8mA DC BIAS

Input (R8-R9), Input(R2-R3), Input (R4-R5), Input(R10-R11): 160 μH min.

Input (R13-R14): 40 μH min.

3.11 HiPot Test

Input(R8-R9) To Output(C1-C2) : 1500Vac 60s or 2250Vdc 60s

Input(R2-R3) To Output(C3-C6) : 1500Vac 60s or 2250Vdc 60s

Input(R4-R5) To Output(C4-C5) : 1500Vac 60s or 2250Vdc 60s

Input(R10-R11) To Output(C7-C8) : 1500Vac 60s or 2250Vdc 60s

www.ude-corp.com- 10 -

Spec No. : GTD0001-00 GTD-1C00VS14

4. ORDER INFORMATION

G T D - 1 C 00 4

A B D

A. LED Code :

B. Mechanical Code :

C. Schematics Code :

D. Plating Code :

A : 1 :

C : 6 :

B :

D : 2 :

F : 3 :

G : 4 :

www.ude-corp.com

C

VS1

- 11 -

15μ " gold 15μ " gold

30μ " gold

w/ UDE Small logo, w/ T&S Spring

30μ " gold

50μ " gold 50μ " gold

10μ " gold

50μ " min. Nickel overall

120μ " min. Matted Tin

Gold Flash

120μ " min. Bright Tin

Gold Flash

Contact Area

6μ " gold6μ " gold

VS1 : VS1 circuit

Underplating

Solder Tail

L-Green;R-Green. <Refer to Schematic of LED>

Spec No. : GTD0001-00 GTD-1C00VS14

5. IR REFLOW TEMPERATURE PROFILE

www.ude-corp.com- 12 -

Spec No. : GTD0001-00 GTD-1C00VS14

6. Revision History

www.ude-corp.com- 13 -

Issue Date Revision Comments Operator

2013/12/17 A Initial Release . Bin

2014/11/24

2015/7/2 D Update High Frequence SPEC Jeffrey

2014/12/4 C KenUpdate Panel Cutout Drawing

2015/7/14 EChange General Tolerance

from .X :± 0.38;..XX ± 0.25 to .X :± 0.38; ..XX ± 0.20

,product width from 17.78 to 17.53,and update Panel Cutout

Poter

B Update Mechanical Drawing Ken