Scope of AccreditationADNOC DISTRIBUTION TESTING LABORATORY- NAL 005

Sas Al Nakheel-Abu Dhabi

Page 1 of 2

- Chemical Testing

Product Tested Type of Test and PropertiesMeasured

Test Method(Standard No. &

issue date)

Lubricating Oil

Test method for Flash and Fire Points by Cleveland Open Cup Tester ASTM D 92 – 05a

Test method for Flash Point by Pensky-Martens Closed CupTester.

ASTM D 93 – 02a

Test method for Water in Petroleum Products and BituminousMaterials by Distillation.

ASTM D 95 – 05 έ1

Test method for Pour Point of Petroleum Products. ASTM D 97 – 05a

Test method for Corrosiveness to of copper from petroleumproducts by the copper strip test.

ASTM D 130 – 04 έ1

Test method for Kinematic Viscosity of Transparent andOpaque Liquids (and the Calculation of Dynamic Viscosity).

ASTM D 445 – 04 έ2

Test method for Ash from Petroleum Products. ASTM D 482– 03

Test method for Rust-Preventing Characteristics of InhibitedMineral Oil in presence of Water

ASTM D 665– 03

Test method for Foaming Characteristics of Lubricating Oils. ASTM D 892 – 03

Test method for pH of Engine Coolants and Antirusts. ASTM D 1287 –91(02)

Test method for ASTM colour of petroleum products(ASTM colourscale).

ASTM D 1500 – 04a

Practise for Calculating Viscosity Index from KinematicViscosity at 40° and 100°C.

ASTM D 2270 – 04

Test method for Oxidation Stability of Steam Turbine Oils byRotating Pressure Vessel.

ASTM D 2272 – 02

Test method for Base Number of Petroleum Products byPotentiometric Perchloric Acid Titration.

ASTM D 2896 – 05

Test method for Air Release Properties of Petroleum Oils. ASTM D 3427 – 03

Test method for Determination of Additive elements inLubricating Oils by inductively coupled plasma atomicemission spectrometry.

ASTM D 4951 – 02

Scope of AccreditationADNOC DISTRIBUTION TESTING LABORATORY- NAL 005

Sas Al Nakheel-Abu Dhabi

Page 2 of 2

Product Tested Type of Test and PropertiesMeasured

Test Method(Standard No. &

issue date)

Lubricating Oil

Test method for Determination of Additive elements, WearMetals and Contaminants in used Lubricating Oils andDetermination of selected Elements in Base Oils byInductively Coupled Plasma Atomic Emission Spectrometry(ICP-AES).

ASTM D 5185 – 05

Test method for Apparent Viscosity of Engine Oils Between -5and -30°C Using the Cold-Cranking Simulator.

ASTM D 5293 – 05

Grease

Test method for Cone Penetration of Lubricating Grease. ASTM D-217 – 02

Test method for Determining the Water WashoutCharacteristics of Lubricating Greases.

ASTM D- 1264–03 έ 1

Test method for Dropping Point of Lubricating Grease OverWide Temperature Range.

ASTM D- 2265–00

Fuels

Test method for Distillation of Petroleum Products at AtmosphericPressure.

ASTM D-86 – 05

Test method for Flash Point by Pensky-Martens Closed CupTester.

ASTM D-93 – 02a

Test method for Water in Petroleum Products and BituminousMaterials by Distillation.

ASTM D-95 – 05 έ 1

Test method for Pour Point of Petroleum Products. ASTM D-97 – 05a

Test method for Corrosiveness to of copper from petroleumproducts by the copper strip test.

ASTM D-130 – 04 έ1

Test method for Kinematic Viscosity of Transparent andOpaque Liquids (the Calculation of Dynamic Viscosity).

ASTM D-445 – 04 έ2

Test method for Smoke Point of Kerosene and Aviation Turbine Fuel. ASTM D-1322 –97(2002) έ1

Prepared by: Eng. Oraib Al-Dmour