PSD:3006 HF Drivers · 2016. 2. 10. · 80W (AES500 specification w/ xover ≥ 500Hz @ 12dB/octave)...
1
PSD:3006 HF Drivers ** Multiple units exceeded published power rating evaluated under AES noise sources and test standards while mounted on Eminence’s H2EA horn in a non-temperature controlled environment. *** The average on axis output across the entire usable frequency range when mounted to the H2EA horn and applying 1W/1m into the nominal impedance, i.e. 2.83V/8Ω, 4V/16Ω. Eminence response curves are measured under the following conditions: All speakers are tested at 1W/1m using a variety of test set-ups for the appropriate impedance | LMS using 0.25” supplied microphone (software calibrated) mounted 1m from wall/baffle | 2ft x 2ft baffle is built into the wall with horn front mounted | Carver PM-120 amplifier | 2700ft3 chamber with fiberglass on all six surfaces (three with custom-made wedges). Throat Size Nominal Impedance Power Rating** Free Air Resonance Usable Frequency Range Recommended Crossover Sensitivity*** Magnet Weight Voice Coil Diameter Re Minimum Impedance 2”, 50.8mm 8 or 16 ohms 100W (AES) 470Hz 800Hz-20kHz 12dB/oct @800Hz 109dB (1W/1m across 800Hz-20kHz on axis on H2EA horn) 80 oz. 3”, 76.2mm 4.8 ohms 7.1 ohms @3.4kHz Specification Overall Diameter Mounting Holes Diameter Mounting Holes B.C.D. Mounting Thread Depth Weight Volume 7.9”, 200.7mm 4X 1/4-20 4”, 101.6mm N/A 3.1”, 78.7mm 13.5 lbs, 6.1 kg 83.11 cu.in. Mounting Information Available in bolt-on format only Materials of Construction Voice Coil Former Diaphragm Material Magnet Composition Polyimide Titanium w/ geodesic design for increased strength and break up control Ferrite PSD:3006 measured on Eminence H2EA horn.
Transcript of PSD:3006 HF Drivers · 2016. 2. 10. · 80W (AES500 specification w/ xover ≥ 500Hz @ 12dB/octave)...
PSD:3006 HF Drivers
** Multiple units exceeded published power rating evaluated under AES noise sources and test standards while mounted on Eminence’s H2EA horn in a non-temperature controlled environment.
*** The average on axis output across the entire usable frequency range when mounted to the H2EA horn and applying 1W/1m into the nominal impedance, i.e. 2.83V/8Ω, 4V/16Ω. Eminence response curves are measured under the following conditions: All speakers are tested at 1W/1m using a variety of test set-ups for the appropriate impedance | LMS using 0.25” supplied microphone (software calibrated) mounted 1m from wall/baffle | 2ft x 2ft baffle is built into the wall with horn front mounted | Carver PM-120 amplifier | 2700ft3 chamber with fiberglass on all six surfaces (three with custom-made wedges).
Throat SizeNominal ImpedancePower Rating**Free Air ResonanceUsable Frequency RangeRecommended CrossoverSensitivity***
Magnet WeightVoice Coil DiameterReMinimum Impedance
2”, 50.8mm8 or 16 ohms100W (AES)
470Hz800Hz-20kHz
12dB/oct @800Hz109dB (1W/1m across 800Hz-20kHz on
axis on H2EA horn)80 oz.
3”, 76.2mm4.8 ohms
7.1 ohms @3.4kHz
Specification
Overall DiameterMounting Holes DiameterMounting Holes B.C.D.Mounting ThreadDepthWeightVolume
7.9”, 200.7mm4X 1/4-20
4”, 101.6mmN/A
3.1”, 78.7mm13.5 lbs, 6.1 kg
83.11 cu.in.
Mounting InformationAvailable in bolt-on format only
Materials of ConstructionVoice Coil FormerDiaphragm Material
Magnet Composition
PolyimideTitanium w/ geodesic design for increased
strength and break up controlFerrite
PSD:3006 measured on Eminence H2EA horn.
