Cal. VD36B - Quality Watch Movement | TMI | TIME MODULEIssued on : 01. March. 2018 ψ 29. 50 mm H...
Transcript of Cal. VD36B - Quality Watch Movement | TMI | TIME MODULEIssued on : 01. March. 2018 ψ 29. 50 mm H...
Issued on : 01. March. 2018
ψ 29. 50 mm
H 3.97 mm
Specification - 1
Specification - 2
Appearance
Casing
Hand Fitting
Hand Setting Stem
Dial
Assembly Plan - 1
Assembly Plan - 2
Hands
SII Products
Cal. VD36B
Version 1
Version 1
Version 1
Version 1
Version 1
Version 1
Version 1
Version No.Item
Version 1
Version 1
Version 1
MOVEMENT SPECIFICATION - 1
1. MOVEMENT DIMENSIONS
· Outside diameter ψ29.50mm (12H~6H) x 26.00mm (3H~9H)
· Casing diameter ψ28.80mm (12H~6H)
· Total height 3.97 mm
· Dimensions of small hands away from center 7.50 mm
2. TIME STANDARD
· Type of quartz oscillator Tuning fork
· Frequency of quartz oscillator 32,768 Hz
· Accuracy Monthly rate: Less than 20 seconds per month at
normal temperature range
· Regulation device Nil
· Regulation hands unbalance Hour hand : Less than 0.60 µN·m ( 60mg·mm )
Minute hand : Less than 0.90 µN·m ( 90mg·mm )
Second hand : Less than 0.09 µN·m ( 9mg·mm )
Dual time hand : Less than 0.05 µN·m ( 5mg.mm )
· Additional function Dual time hour (24 hours)
Dual time minute (60 minutes)
3. BATTERY
· Type Silver oxide battery
· Size ψ9.5 x t 2.0 ( mm )
· Battery life Approx. 3 years
· Recommended battery SR920SW ( SEIZAIKEN )
4. STEPPING MOTOR
· Number of units 3 pieces
· Type Two pole stepping motor
· Step 180° every second
5. JEWEL 0 jewel
6. ANTIMAGNETISM ≧1600 A / m ( Will not affected by general household appliance )
( direct current magnetic field )
7. SHOCK RESISTANCE On equal level with general quartz movement
8. OPERATING TEMPERATURE RANGE From - 5 ℃ to + 50 ℃
9. TEST OF ACCURACY
· Equipment to be used SEIKO Quartz Tester QT - 99
Greiner Quartz Timer - C
Witschi Q-Tester 4000
· Duration of measurement 10 seconds
· Microphone to be used Electromagnetic detection type
10. ATTACHED PARTS
* All specifications are subject to change without notice.
SII Products Version: 1
0351-1780 (Normal)
Three Hands with 2 Eyes (Regulator Dual Time of 24H & 60M)
CAL.VD36B 12 3 / 4 Ligne Quartz Movement
3013 - 14G0
0110 - 3400
Parts Name
Hand setting stem
Sticker
Silver oxide battery
Parts Code
Movement Specification - 2
OPERATION
Version 1
SII Products
CAL. VD36B
3 step motors ( 3 hands, dual time of 24 hour )
24H hand
3 hands
First click position
Minute hand
Dual time
Free
Dual time correction
-1 hour / PUSH
Dual time correction
+1 hour / PUSH
Normal position
First click positionDual time zero position reset mode
( AC finished = Reset relieved )
Dual time correction
-1 minute / PUSH
( Keep pushing :
hand moving fast )
Dual time correction
+1 minute / PUSH
( Keep pushing :
hand moving fast )
Time setting
Reset switch
Second setting device
Dual time (24H) correction
+1 step / PUSH
( Keep pushing :
hand moving fast )
Dual time (minute) correction
+1 step / PUSH
( Keep pushing :
hand moving fast )
*Hands demonstration while AC reset :
Dual time of 24 hour hand : 1 cycle
Dual time of minute hand :
Counter clockwise 1/2 cycle,
Clockwise 1/2 cycle.
Time setting
Reset switch
Second setting device
*After the Dual time hand reset to the [0:00]
position, push the crown back to normal position.
AC functions
(Keep buttons
"A" & "B"
pressed at the
same time for
2 seconds,
and then release
the buttons)
Center post 中心柱位
Maximum height from main plate surface 與機芯平面之最大高度
Total height incl. movement 機芯總高度
Type M 一般針高
Type L 高針
Type M 一般針高
Type L 高針
Hour wheel 時針輪
Center wheel 分針輪
Fourth wheel 秒針輪Dual 24 hour wheel 兩地時間24小時針輪
Dual small minute wheel 兩地時間小分針輪
Type M 一般針高 Type L 高針
Type M 一般針高
Type L 高針