MS5803-14BA Miniature 14 bar Module · MS5803-14BA Miniature 14 bar Module DA5803-14BA_005 ...

MS5803-14BA Miniature 14 bar Module

DA5803-14BA_005 www.meas-spec.com September 7, 2012 000058031641 ECN1703 1/20

• High resolution module, 0.2 mbar • Fast conversion down to 1 ms • Low power, 1 µA (standby < 0.15 µA) • Integrated digital pressure sensor (24 bit ΔΣ ADC) • Supply voltage 1.8 to 3.6 V • Operating range: 0 to 14 bar, -40 to +85 °C • I2C and SPI interface (Mode 0,3) • No external components (Internal oscillator) • Excellent long term stability • Hermetically sealable for outdoor devices

DESCRIPTION

The MS5803-14BA is a new generation of high resolution pressure sensors with SPI and I2C bus interface. It is optimized for depth measurement systems with a water depth resolution of 1cm and below. The sensor module includes a high linear pressure sensor and an ultra low power 24 bit ΔΣ ADC with internal factory calibrated coefficients. It provides a precise digital 24 Bit pressure and temperature value and different operation modes that allow the user to optimize for conversion speed and current consumption. A high resolution temperature output allows the implementation of a depth measurement systems and thermometer function without any additional sensor. The MS5803-14BA can be interfaced to any microcontroller. The communication protocol is simple, without the need to programming internal registers in the device. The gel protection and antimagnetic stainless steel cap protects against 30 bar overpressure water resistant. This new sensor module generation is based on leading MEMS technology and latest benefits from the Intersema’s proven experience and know-how in high volume manufacturing of pressure modules have been widely used for over a decade. This sensing principle employed leads to very low hysteresis and high stability of both pressure and temperature signal.

FEATURES

FIELD OF APPLICATION TECHNICAL DATA

• Mobile water depth measurements systems Sensor Performances (VDD = 3 V)

• Diving computers Pressure Min Typ Max Unit

• Adventure or multi-mode watches Range 0 14 bar

FUNCTIONAL BLOCK DIAGRAM

VDD

GND

PS

SCLK

SDO

SDI/SDA

Meas. MUX

ADC

DigitalInterface

Memory(PROM)128 bits

SENSOR

SGND

+IN

-INdig.

Filter

SensorInterface IC

PGA

CSB

ADC 24 bit

Resolution (1) 1 / 0.6 / 0.4 / 0.3 / 0.2 mbar

Accuracy 0°C to +40°C, 0 to 6 bar (2) -20 +20 mbar

Accuracy -40°C to + 85°C 0 to 6 bar (2) -40 +40 mbar

Response time 0.5 / 1.1 / 2.1 / 4.1 / 8.22 ms

Long term stability -20 mbar/yr

Temperature Min Typ Max Unit

Range -40 +85 °C

Resolution <0.01 °C

Accuracy -0.8 +0.8 °C Notes: (1) Oversampling Ratio: 256 / 512 / 1024 / 2048 / 4096 (2) With autozero at one pressure point



PERFORMANCE SPECIFICATIONS

ABSOLUTE MAXIMUM RATINGS Parameter Symbol Conditions Min. Typ. Max Unit Supply voltage VDD -0.3 +4.0 V Storage temperature TS -40 +125 °C Overpressure Pmax ISO 6425 30 bar Maximum Soldering Temperature Tmax 40 sec max 250 °C

ESD rating Human Body Model -4 +4 kV

Latch up JEDEC standard No 78 -100 +100 mA

ELECTRICAL CHARACTERISTICS

Parameter Symbol Conditions Min. Typ. Max Unit Operating Supply voltage VDD 1.8 3.0 3.6 V Operating Temperature T -40 +25 +85 °C

Supply current (1 sample per sec.) IDD

OSR 4096 2048 1024

512 256

12.5 6.3 3.2 1.7 0.9

µA

Peak supply current during conversion 1.4 mA Standby supply current at 25°c 0.02 0.14 µA VDD Capacitor From VDD to GND 100 nF

ANALOG DIGITAL CONVERTER (ADC)

Parameter Symbol Conditions Min. Typ. Max Unit Output Word 24 bit

Conversion time tc

OSR 4096 2048 1024

512 256

7.40 3.72 1.88 0.95 0.48

8.22 4.13 2.08 1.06 0.54

9.04 4.54 2.28 1.17 0.60

ms



PERFORMANCE SPECIFICATIONS (CONTINUED)

PRESSURE OUTPUT CHARACTERISTICS (VDD = 3 V, T = 25°C UNLESS OTHERWISE NOTED) Parameter Conditions Min. Typ. Max Unit Operating Pressure Range Prange Full Accuracy 0 14 bar

Absolute Accuracy, Temperature range 0 … 40 °C

0 … 6 bar 0 … 10 bar 0 … 14 bar

-20 -60

-150

+20 +20 +20

mbar

Absolute Accuracy, Temperature range -40 … 85 °C

0 … 6 bar 0 … 10 bar 0 … 14 bar

-40 -120 -200

+40 +80

+100 mbar

Maximum error with supply voltage (1) VDD = 1.8 V … 3.6 V -20 +20 mbar

Long-term stability -20 mbar/yr

Resolution RMS

OSR 4096 2048 1024

512 256

0.2 0.3 0.4 0.6 1.0

mbar

(1) With autozero at 3V point TEMPERATURE OUTPUT CHARACTERISTICS (VDD = 3 V, T = 25°C UNLESS OTHERWISE NOTED)

Parameter Conditions Min. Typ. Max Unit

Absolute Accuracy 0 …10 bar -20..85°C -40..85°C

-0.8 -2.0 -4.0

+0.8 +2.0 +4.0

°C

Maximum error with supply voltage (1) VDD = 1.8 V … 3.6 V -0.5 +0.5 °C

Resolution RMS

OSR 4096 2048 1024

512 256

0.002 0.003 0.005 0.008 0.012

°C

(1) With autozero at 3V point



PERFORMANCE SPECIFICATIONS (CONTINUED)

DIGITAL INPUTS (PS, CSB, DIN, SCLK, SDA, SCL) Parameter Symbol Conditions Min. Typ. Max Unit Serial data clock SCLK SPI protocol 20 MHz Serial data clock SCL I2C protocol 400 kHz Input high voltage VIH Pins CSB 80% VDD 100% VDD V Input low voltage VIL 0% VDD 20% VDD V Input leakage current I leak25°C at 25°c 0.15 µA CS low to first SCLK rising tCSL 21 ns CS low from last SCLK falling tCSH 21 ns

PRESSURE OUTPUTS (DOUT, SDA, SCL)

Parameter Symbol Conditions Min. Typ. Max Unit Output high voltage VOH Isource = 0.6 mA 80% VDD 100% VDD V Output low voltage VOL Isink = 0.6 mA 0% VDD 20% VDD V Load capacitance CLOAD 16 pF



FUNCTIONAL DESCRIPTION

Figure 1: Block diagram of MS5803-14BA

GENERAL The MS5803-14BA consists of a piezo-resistive sensor and a sensor interface IC. The main function of the MS5803-14BA is to convert the uncompensated analogue output voltage from the piezo-resistive pressure sensor to a 24-bit digital value, as well as providing a 24-bit digital value for the temperature of the sensor. FACTORY CALIBRATION Every module is individually factory calibrated at two temperatures and two pressures. As a result, 6 coefficients necessary to compensate for process variations and temperature variations are calculated and stored in the 128-bit PROM of each module. These bits (partitioned into 6 coefficients W1 to W6) must be read by the microcontroller software and used in the program converting D1 and D2 into compensated pressure and temperature values. The 2 coefficients W0 and W7 are for factory configuration and CRC. SERIAL INTERFACE The MS5803-14BA has built in two types of serial interfaces: SPI and I2C. Pulling the Protocol Select pin PS to low selects the SPI protocol, pulling PS to high activates the I2C bus protocol. Pin PS Mode Pins used High I2C SDA, SCL, CSB Low SPI SDI, SDO, SCLK, CSB SPI MODE The external microcontroller clocks in the data through the input SCLK (Serial CLocK) and SDI (Serial Data In). In the SPI mode module can accept both mode 0 and mode 3 for the clock polarity and phase. The sensor responds on the output SDO (Serial Data Out). The pin CSB (Chip Select) is used to enable/disable the interface, so that other devices can talk on the same SPI bus. The CSB pin can be pulled high after the command is sent or after the end of the command execution (for example end of conversion). The best noise performance from the module is obtained when the SPI bus is quiet and without communication to other devices during the ADC conversion in progress.

VDD

GND

PS

SCLK / SCL SDO SDI / SDA

Meas. MUX

ADC

Digital Interface

Memory (PROM) 128 bits

SENSOR

SGND

+IN

-IN dig.

Filter

Sensor Interface IC

PGA

CSB



I2C MODE The external microcontroller clocks in the data through the input SCLK (Serial CLocK) and SDA (Serial DAta). The sensor responds on the same pin SDA which is bidirectional for the I2C bus interface. So this interface type uses only 2 signal lines and does not require a chip select, which can be favourable to reduce board space. In I2C-Mode the complement of the pin CSB (Chip Select) represents the LSB of the I2C address. It is possible to use two sensors with two different addresses on the I2C bus. The pin CSB shall be connected to VDD or GND (do not leave unconnected!). Pin CSB Address (7 bits) High 0x76 (1110110 b) Low 0x77 (1110111 b) COMMANDS The MS5803-14BA has only five basic commands:

1. Reset 2. Read PROM (128 bit of calibration words) 3. D1 conversion 4. D2 conversion 5. Read ADC result (24 bit pressure / temperature)

Size of each command is 1 byte (8 bits) as described in the table below. After ADC read commands the device will return 24 bit result and after the PROM read 16bit result. The address of the PROM is embedded inside of the PROM read command using the a2, a1 and a0 bits.

Command byte hex value Bit number 0 1 2 3 4 5 6 7 Bit name PR

M COV - Typ Ad2/

Os2 Ad1/Os1

Ad0/Os0

Stop

Command Reset 0 0 0 1 1 1 1 0 0x1E Convert D1 (OSR=256) 0 1 0 0 0 0 0 0 0x40 Convert D1 (OSR=512) 0 1 0 0 0 0 1 0 0x42 Convert D1 (OSR=1024) 0 1 0 0 0 1 0 0 0x44 Convert D1 (OSR=2048) 0 1 0 0 0 1 1 0 0x46 Convert D1 (OSR=4096) 0 1 0 0 1 0 0 0 0x48 Convert D2 (OSR=256) 0 1 0 1 0 0 0 0 0x50 Convert D2 (OSR=512) 0 1 0 1 0 0 1 0 0x52 Convert D2 (OSR=1024) 0 1 0 1 0 1 0 0 0x54 Convert D2 (OSR=2048) 0 1 0 1 0 1 1 0 0x56 Convert D2 (OSR=4096) 0 1 0 1 1 0 0 0 0x58 ADC Read 0 0 0 0 0 0 0 0 0x00 PROM Read 1 0 1 0 Ad2 Ad1 Ad0 0 0xA0 to

0xAE

Figure 2: Command structure



PRESSURE AND TEMPERATURE CALCULATION

Size [1]

[bit] min max

C1 Pressure sensitivity | SENS T1 unsigned int 16 16 0 65535 46546

C2 Pressure offset | OFF T1 unsigned int 16 16 0 65535 42845

C3 Temperature coefficient of pressure sensitivity | TCS unsigned int 16 16 0 65535 29751

C4 Temperature coefficient of pressure offset | TCO unsigned int 16 16 0 65535 29457

C5 Reference temperature | T REF unsigned int 16 16 0 65535 32745

C6 Temperature coefficient of the temperature | TEMPSENS unsigned int 16 16 0 65535 29059

D1 Digital pressure value unsigned int 32 24 0 16777216 4311550

D2 Digital temperature value unsigned int 32 24 0 16777216 8387300

dTDifference between actual and reference temperature [2]

dT = D2 - T REF = D2 - C5 * 2 8 signed int 32 25 -16776960 16777216 4580

2015

= 20.15 °C

OFFOffset at actual temperature [3]

OFF = OFFT1 + TCO * dT = C2 * 216 + (C4 * dT ) / 27 signed int 64 41 -8589672450 12884705280 2808943928

SENSSensitivity at actual temperature [4]

SENS = SENST1 + TCS * dT = C1 * 2 15 + (C3 * dT ) / 28 signed int 64 41 -4294836225 6442352640 1525751591

10005

= 1000.5 mbar

Notes[1][2][3][4]

Calculate temperature compensated pressure

8500-4000TEMP 41

Convert calibration data into coefficients (see bit pattern of W1 to W4)

Variable Example /Typical

ValueRecommendedvariable typeDescription | Equation

signed int 32Actual temperature (-40…85°C with 0.01°C resolution)TEMP = 20°C + dT * TEMPSENS = 2000 + dT * C6 / 223

Read digital pressure and temperature data

signed int 32Temperature compensated pressure (0…14bar with0.1mbar resolution)P = D1 * SENS - OFF = (D1 * SENS / 2 21 - OFF) / 2 15

min and max have to be defined

min and max have to be definedmin and max have to be defined

Maximal size of intermediate result during evaluation of variable

140000058P

StartMaximum values for calculation results:

PMIN = 0mbar P MAX = 14barTMIN = -40°C T MAX = 85°C T REF = 20°C

Read calibration data (factory calibrated) from PROM

Read digital pressure and temperature data

Calculate temperature

Calculate temperature compensated pressure

Display pressure and temperature value

Figure 3: Flow chart for pressure and temperature reading and software compensation.



SECOND ORDER TEMPERATURE COMPENSATION

Yes No

SENS2 = 5 ⋅ (TEMP – 2000)2 / 23

SENS = SENS - SENS2

TEMP<20°C

Low temperature

OFF2 = 1 ⋅ (TEMP – 2000)2 / 24

OFF2 = 3 ⋅ (TEMP – 2000)2 / 21

OFF = OFF - OFF2 TEMP = TEMP - T2

Low temperature High temperature

Calculate pressure and temperature

TEMP<-15°C No Yes

OFF2 = OFF2 + 7 ⋅ (TEMP + 1500)2

Low temperature Very low temperature

SENS2 = 0

T2 = 3 ⋅ dT2 / 233 T2 = 7 ⋅ dT2 / 237

SENS2 = SENS2 + 4 ⋅ (TEMP + 1500)2

Figure 4: Flow chart for pressure and temperature to the optimum accuracy.



SPI INTERFACE

RESET SEQUENCE The Reset sequence shall be sent once after power-on to make sure that the calibration PROM gets loaded into the internal register. It can be also used to reset the device ROM from an unknown condition

Figure 5: Reset command sequence SPI mode 0

Figure 6: Reset command sequence SPI mode 3

0 1 2 3 4 5 6 7

SCLK

CSB

SDI

SDO

PS

2.8ms RELOAD



CONVERSION SEQUENCE The conversion command is used to initiate uncompensated pressure (D1) or uncompensated temperature (D2) conversion. The chip select can be disabled during this time to communicate with other devices. After the conversion, using ADC read command the result is clocked out with the MSB first. If the conversion is not executed before the ADC read command, or the ADC read command is repeated, it will give 0 as the output result. If the ADC read command is sent during conversion the result will be 0, the conversion will not stop and the final result will be wrong. Conversion sequence sent during the already started conversion process will yield incorrect result as well.

0 1 2 3 4 5 6 7

SCLK

CSB

SDI

SDO

PS

8.22ms ADC CONVERSION

Figure 7: Conversion out sequence, Typ=d1, OSR = 4096

Figure 8: ADC Read sequence

PROM READ SEQUENCE The read command for PROM shall be executed once after reset by the user to read the content of the calibration PROM and to calculate the calibration coefficients. There are in total 8 addresses resulting in a total memory of 128 bit. Address 0 contains factory data and the setup, addresses 1-6 calibration coefficients and address 7 contains the serial code and CRC. The command sequence is 8 bits long with a 16 bit result which is clocked with the MSB first.

Figure 9: PROM Read sequence, address = 011 (Coefficient 3).



I2C INTERFACE

COMMANDS Each I2C communication message starts with the start condition and it is ended with the stop condition. The MS5803-14BA address is 111011Cx, where C is the complementary value of the pin CSB. Since the IC does not have a microcontroller inside, the commands for I2C and SPI are quite similar. RESET SEQUENCE The reset can be sent at any time except when the power on did not work it could be possible that the acknowledge blocks the SDA. When SDA is blocked by an undefined state the only way to get the MS5803-14BA to work is to send a power on reset.

1 1 1 0 1 1 CSB 0 0 0 0 0 1 1 1 1 0 0

S W A A P

From Master S = Start Condition W = Write A = AcknowledgeFrom Slave P = Stop Condition R = Read N = Not Acknowledge

cmd byteDevice AddressDevice Address

command

Figure 10: I2C Reset Command CONVERSION SEQUENCE A conversion can be started by sending the command to MS5803-14BA. When command is sent to the system it stays busy until conversion is done. When conversion is finished the data can be accessed by sending a Read command, when an acknowledge appears from the MS5803-14BA, you may then send 24 SCLK cycles to get all result bits. Every 8 bit the system waits for an acknowledge signal.

1 1 1 0 1 1 CSB 0 0 0 1 0 0 1 0 0 0 0

S W A A P


commandcmd byte

Device AddressDevice Address

Figure 11: I2C Command to initiate a pressure conversion (OSR=4096, typ=D1)

1 1 1 0 1 1 CSB 0 0 0 0 0 0 0 0 0 0 0

S W A A P


commandDevice AddressDevice Address cmd byte

Figure 12: I2C ADC read sequence

1 1 1 0 1 1 CSB 1 0 X X X X X X X X 0 X X X X X X X X 0 X X X X X X X X 0

S R A A A N P


data data dataDevice AddressDevice Address

Data 23-16 Data 7 - 0Data 8 - 15

Figure 13: I2C pressure response (D1) on 24 bit from MS5803-14BA



PROM READ SEQUENCE The PROM Read command consists of two parts. First command sets up the system into PROM read mode. The second part gets the data from the system.

Figure 11: I2C Command to read memory address= 011 (Coefficient 3)

Figure 14: I2C answer from MS5803-14BA

CYCLIC REDUNDANCY CHECK (CRC)

MS5803-14BA contains a PROM memory with 128-Bit. A 4-bit CRC has been implemented to check the data validity in memory. The application note AN520 describes in detail CRC-4 code used.

A d d

DB15

DB14

DB13

DB12

DB11

DB10

DB9

DB8

DB7

DB6

DB5

DB4

DB3

DB2

DB1

DB0

0 16 bit reserved for manufacturer 1 Coefficient 1 (16 bit unsigned) 2 Coefficient 2 (16 bit unsigned) 3 Coefficient 3 (16 bit unsigned) 4 Coefficient 4 (16 bit unsigned) 5 Coefficient 5 (16 bit unsigned) 6 Coefficient 6 (16 bit unsigned) 7 CRC

Figure 15: Memory PROM mapping



APPLICATION CIRCUIT

The MS5803-14BA is a circuit that can be used in conjunction with a microcontroller in mobile depth-meter applications. It is designed for low-voltage systems with a supply voltage of 3 V.

Figure 16: Typical application circuit with SPI / I2C protocol communication

MS5803-14BA

MS5803-14BA



PACKAGE OUTLINE AND PIN CONFIGURATION

TOP view

Pin Name Type Function

1 SCLK I Serial data clock

2 GND G Ground

3 CSB I Chip Select (active low)

4 NC NC -

5 VDD P Positive supply voltage

6 PS I Communication protocol select SPI / I2C

7 SDI/SDA I Serial data input

8 SDO O Serial data output

Figure 17: MS5803-14BA package outlines, pin configuration and description Notes: (1) Dimensions in mm (2) General tolerance ±0.1 (3) Cap centering ± 0.15 from center of the ceramic

RECOMMENDED PAD LAYOUT

8 1 7 2 6 3 5 4

5 4 6 3 7 2

8 1



SHIPPING PACKAGE

Tube

Tape & reel



MOUNTING AND ASSEMBLY CONSIDERATIONS

SOLDERING Please refer to the application note AN808 available on our website for all soldering issues. MOUNTING The MS5803-14BA can be placed with automatic Pick & Place equipment using vacuum nozzles. It will not be damaged by the vacuum. Due to the low stress assembly the sensor does not show pressure hysteresis effects. It is important to solder all contact pads. CONNECTION TO PCB The package outline of the module allows the use of a flexible PCB for interconnection. This can be important for applications in watches and other special devices. SEALING WITH O-RINGS In products like outdoor watches the electronics must be protected against direct water or humidity. For those products the MS5803-14BA provides the possibility to seal with an O-ring. The protective cap of the MS5803-14BA is made of special anticorrosive stainless steel with a polished surface. In addition to this the MS5803-14BA is filled with silicone gel covering the sensor and the bonding wires. The O-ring (or O-rings) shall be placed at the outer diameter of the metal cap. This method avoids mechanical stress because the sensor can move in vertical direction. CLEANING The MS5803-14BA has been manufactured under cleanroom conditions. It is therefore recommended to assemble the sensor under class 10’000 or better conditions. Should this not be possible, it is recommended to protect the sensor opening during assembly from entering particles and dust. To avoid cleaning of the PCB, solder paste of type “no-clean” shall be used. Cleaning might damage the sensor! ESD PRECAUTIONS The electrical contact pads are protected against ESD up to 4 kV HBM (human body model). It is therefore essential to ground machines and personnel properly during assembly and handling of the device. The MS5803-14BA is shipped in antistatic transport boxes. Any test adapters or production transport boxes used during the assembly of the sensor shall be of an equivalent antistatic material. DECOUPLING CAPACITOR Particular care must be taken when connecting the device to the power supply. A 100 nF ceramic capacitor must be placed as close as possible to the MS5803-14BA VDD pin. This capacitor will stabilize the power supply during data conversion and thus, provide the highest possible accuracy.



PERFORMANCE CHARACTERISTICS

PRESSURE ERROR VS PRESSURE AND TEMPERATURE

-120.0

-100.0

-80.0

-60.0

-40.0

-20.0

0.0

20.0

40.0

0 2000 4000 6000 8000 10000 12000 14000

Pres

sure

err

or [m

bar]

Pressure [mbar]

Absolute pressure accuracy with 2nd order compensationTypical

85

25

-40

-120.0

-60.0

0.0

60.0

120.0

180.0

-40 -20 0 20 40 60 80

Pres

sure

err

or [m

bar]

Temperature [°C]

Pressure accuracy vs temperatureTypical

14000mbar 2nd order

6000mbar 2nd order

14000mbar 1st order

6000mbar 1st order



TEMPERATURE ERROR VS TEMPERATURE

-4.0

-2.0

0.0

2.0

4.0

6.0

8.0

10.0

12.0

-40 -20 0 20 40 60 80

Tem

pera

ture

err

or [°

C]

Temperature [°C]

Temperature accuracy vs temperatureTypical

1000mbar 2nd order

1000mbar 1st order



PERFORMANCE CHARACTERISTICS (CONTINUED)

PRESSURE ERROR VS POWER SUPPLY

-20.0

-10.0

0.0

10.0

20.0

1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6

Pres

sure

err

or [m

bar]

Supply voltage [V]

Pressure error vs supply voltage at 25°CTypical

1000 mbar

4000 mbar

6000 mbar

14000 mbar

TEMPERATURE ERROR VS POWER SUPPLY

-0.5

-0.4

-0.3

-0.2

-0.1

0.0

0.1

0.2

0.3

0.4

0.5

1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6

Tem

pera

ture

err

or [m

bar]

Supply voltage [V]

Temperature error vs supply voltage at 25°CTypical

1000 mbar

4000 mbar

6000 mbar

14000 mbar



ORDERING INFORMATION

Product Code Product Art. No Delivery Form MS5803-14BA01 Miniature 14 bar Module MS580314BA01-00 Tube MS5803-14BA01 Miniature 14 bar Module MS580314BA01-50 Tape& reel TOP-UP MS5803-14BA01 Miniature 14 bar Module MS580314BA01-50 Tape& reel TOP-DOWN

FACTORY CONTACTS

NORTH AMERICA EUROPE ASIA

Measurement Specialties 45738 Northport Loop West

Fremont, CA 94538

Tel: +1 800 767 1888 Fax: +1 510 498 1578

e-mail: pfg.cs.amerameas-spec.com Website: www.meas-spec.com

MEAS Switzerland Sàrl Ch. Chapons-des-Prés 11

CH-2022 Bevaix

Tel: +41 32 847 9550 Fax: + 41 32 847 9569

e-mail: sales.chameas-spec.com Website: www.meas-spec.com

Measurement Specialties (China), Ltd. No. 26 Langshan Road

Shenzhen High-Tech Park (North) Nanshan District, Shenzhen, 518057

China Tel: +86 755 3330 5088 Fax: +86 755 3330 5099

e-mail: pfg.cs.asiaameas-spec.com Website: www.meas-spec.com

The information in this sheet has been carefully reviewed and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Furthermore, this information does not convey to the purchaser of such devices any license under the patent rights to the manufacturer. Measurement Specialties, Inc. reserves the right to make changes without further notice to any product herein. Measurement Specialties, Inc. makes no warranty, representation or guarantee regarding the suitability of its product for any particular purpose, nor does Measurement Specialties, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Typical parameters can and do vary in different applications. All operating parameters must be validated for each customer application by customer’s technical experts. Measurement Specialties, Inc. does not convey any license under its patent rights nor the rights of others.

http://www.meas-spec.com/



MS5803-14BA Miniature 14 bar Module · MS5803-14BA Miniature 14 bar Module DA5803-14BA_005 ...

Documents

Transcript of MS5803-14BA Miniature 14 bar Module · MS5803-14BA Miniature 14 bar Module DA5803-14BA_005 ...