SERVICE MANUAL
COMPACT DISC PLAYER
AEP ModelUK Model
E ModelAustralian Model
SPECIFICATIONS
CDP-S3Ver 1.3 2002.12
CDP-S3 is the CD player sectionin MHC-S7AV or MHC-S3.
Model Name Using Similar Mechanism NEW
CD Mechanism Type CDM63B-30BD60
Base Unit Name BU-30BD60
Optical Pick-up Name OP Assy (A-MAX.3)
System Compact disc and digitalaudio system
Laser Semiconductor laser(λ=780 nm)Emission duration:continuous
Frequency response 2 Hz – 20 kHz (±0.5 dB)Signal-to-noise ratio More than 90 dBDynamic range More than 90 dBOPTICAL OUT(Square optical connector jack, rear panel)Dimensions (w/h/d) Approx. 280 x 108 x 330 mmMass Approx. 2.7 kg
Design and specifications are subject to changewithout notice.
9-873-831-14 Sony Corporation2002L0500-1 Home Audio Company
C 2002.12 Published by Sony Engineering Corporation
2
CDP-S3
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTEDLINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMSAND IN THE PARTS LIST ARE CRITICAL TO SAFEOPERATION. REPLACE THESE COMPONENTS WITHSONY PARTS WHOSE PART NUMBERS APPEAR ASSHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-LISHED BY SONY.
The laser diode in the optical pick-up block may suffer electro-static break-down because of the potential difference generatedby the charged electrostatic load, etc. on clothing and the humanbody.During repair, pay attention to electrostatic break-down and alsouse the procedure in the printed matter which is included in therepair parts.The flexible board is easily damaged and should be handled withcare.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focusedon the disc reflective surface by the objective lens in the opticalpick-up block. Therefore, when checking the laser diode emis-sion, observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATIONCHECK
Carry out the “S curve check” in “CD section adjustment” andcheck that the S curve waveforms is output three times.
Notes on chip component replacement• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Flexible Circuit Board Repairing• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.• Do not touch the soldering iron on the same conductor of the
circuit board. (within 3 times)• Be careful not to apply force on the conductor when soldering
or unsoldering.
NOTES ON HANDLING THE OPTICAL PICK-UPBLOCK OR BASE UNIT
CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardous ra-diation exposure.
This appliance is classified as a CLASS 1 LASER product.The CLASS 1 LASER PRODUCT MARKING is located onthe rear exterior.
Laser component in this product is capable of emitting radiationexceeding the limit for Class 1.
The following caution label is located inside the unit.
3
CDP-S3
TABLE OF CONTENTS
1. SERVICING NOTES ............................................... 4
2. GENERAL ................................................................... 5
3. DISASSEMBLY3-1. Disassembly Flow ........................................................... 63-2. Cover ............................................................................... 73-3. CD Mechanism Deck (CDM63B-30BD60) ................... 73-4. MAIN Board ................................................................... 83-5. Front Panel Section ......................................................... 83-6. PANEL (L) Board, PANEL (R) Board ........................... 93-7. Lid (CD) .......................................................................... 9
4. TEST MODE .............................................................. 10
5. ELECTRICAL ADJUSTMENTS ......................... 11
6. DIAGRAMS6-1. Note for Printed Wiring Boards
and Schematic Diagrams ................................................ 126-2. Printed Wiring Board – BD Section – ........................... 146-3. Schematic Diagram –BD Section – ............................... 156-4. Printed Wiring Boards – CD CHANGER Section – ..... 166-5. Schematic Diagram – CD CHANGER Section – ......... 176-6. Printed Wiring Board – MAIN Section – ...................... 186-7. Schematic Diagram – MAIN Section – ......................... 196-8. Printed Wiring Boards – PANEL Section – .................. 206-9. Schematic Diagram – PANEL Section – ....................... 216-10. IC Pin Function Description ........................................... 24
7. EXPLODED VIEWS7-1. General Section ............................................................... 267-2. CD Mechanism Deck Section-1
(CDM63B-30BD60) ....................................................... 277-3. CD Mechanism Deck Section-2
(CDM63B-30BD60) ....................................................... 287-4. Base Unit Section (BU-30BD60) ................................... 29
8. ELECTRICAL PARTS LIST ............................... 30
4
CDP-S3SECTION 1
SERVICING NOTES
This set is a component of the MHC-S7AV or MHC-S3.The MHC-S7AV or MHC-S3 system configuration is as shownbelow, and therefore it does not operate normally unless all fourcomponents are connected.In performing the repair, connect all components with the systemcables.Note: The precaution to the users is described on the label stuck onthe back panel (CD player) and in the troubleshooting section inthe Operation Manual.
System Configuration:
POWER SUPPLY
AC IN
TA
SYSTEM & CD µcon
ST
CDP
TC µcon
TC
DISPLAY
CD-TEXT TEST DISC
This unit is able to display the test data (character information)written in the CD on its fluorescent indicator tube.The CD-TEXT TEST DISC (TGCS-313:4-989-366-01) is usedfor checking the display.To check, perform the following procedure.
Checking Method:1. Press the I/1 button to turn the power on, set the disc to the
disc table with the “test disc” label facing up, and chuck thedisc.
2. Press the [CD] button to set CD function, and press then N button to playback the disc.
3. The following will be displayed on the liquid crystal display.Display : 1KHZ/0DB/L R
4. Pressing the [-- ] or [ +] button, select the track. The textdata of each track will be displayed.For details of the displayed contents for each track, refer to “Table1 : CD-TEXT TEST DISC TEXT Data Contents”.
Restrictions in CD-TEXT DisplayIn this unit, some special characters will not be displayed prop-erly. These will be displayed as a space or a character resemblingit.
Table 1 : CD-TEXT TEST DISC TEXT Data Contents(TRACKS No. 1 to 20:Normal Characters)
1 1kHz/0dB/L&R
2 20Hz/0dB/L&R
3 40Hz/0dB/L&R
4 100Hz/0dB/L&R
5 200Hz/0dB/L&R
6 500Hz/0dB/L&R
7 1kHz/0dB/L&R
8 5kHz/0dB/L&R
9 7kHz/0dB/L&R
10 10kHz/0dB/L&R
11 16kHz/0dB/L&R
12 18kHz/0dB/L&R
13 20kHz/0dB/L&R
14 1kHz/0dB/L&R
15 1kHz/–1dB/L&R
16 1kHz/–3dB/L&R
17 1kHz/–6dB/L&R
18 1kHz/–10dB/L&R
19 1kHz/–20dB/L&R
20 1kHz/–60dB/L&R
TRACKNo. Displayed Contents
Note: Track No. 21 to 99 are not displayed.
. >
5
CDP-S3SECTION 2GENERAL
This section is extracted frominstruction manual.
Parts Identification
The items are arranged in alphabetical order.
Refer to the pages indicated in parentheses ( ) for details.
Main unit
m M
.
H S x
>
1 2 3
wjwkwl e; ea
esed
efegehejek
DISC 1–3 ek (14, 15, 21)DISC 1–3 indicators ejDISC 1–3 Z (eject) wl (14)PLAY MODE wj (14, 15, 21)REPEAT wk (14)N (play) eh (14, 15)X (pause) eg (14)x (stop) ef (14, 20). (go back) ed (14, 15, 21)> (go forward) es (14, 15, 21)m (rewind) e; (14)M (fast forward) ea (14)
x
hH
H
hH
O
o
P p
Mm X
>.
1 2 3
wg
qh
qa
wkwjwh
wa
4
5
6
7
qs
qfqd
qg
89q;
qkqlw;
qj
wdws
wf
es
ea
e;wl
CD H es (14, 15)CHECK 5 (15)CLEAR 6 (15)CLOCK/TIMER SELECT qj
(30)CLOCK/TIMER SET qk (13, 21,
29)DBFB qg (23)DISPLAY ws (13, 16, 18, 29, 35)D.SKIP 4 (14)ENTER wg (10, 12, 13, 15, 17,
18, 21, 22, 26–30)EQ qd (27)EQ ON/OFF qf (10, 28)FUNCTION wf (10, 14, 15, 20,
21, 31)GROOVE wa (23)SET UP qs (10, 12, 26, 28, 29)SLEEP 7 (29)SUR wd (25)TAPE A hH ea (19, 35)TAPE B hH e; (19, 20, 35)TUNER/BAND wl (17)TUNING + 9 (17)TUNING – wh (17)TV CH +/– qlTV VOL +/– w;TV @/1 2TV/VIDEO 1VOL +/– qh
BUTTON DESCRIPTIONS
@/1 (power) 3X (pause) q;x (stop) 8. (go back) wk> (go forward) wjm (rewind) whM (fast forward) 9O/o/P/p qa
Remote Control
CDP-S3
6
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
SECTION 3DISASSEMBLY
3-2. COVER(Page 7)
3-3. CD MECHANISM DECK(CDM63B-30BD60)(Page 7)
3-6. PANEL (L) BOARD,PANEL (R) BOARD(Page 9)
3-7. LID (CD)(Page 9)
3-5. FRONT PANEL SECTION(Page 8)
3-4. MAIN BOARD (Page 8)
SET
CDP-S3
7
3-3. CD MECHANISM DECK (CDM63B-30BD60)
Note: Follow the disassembly procedure in the numerical order given.
3-2. COVER
1 two screws(case 3 TP2)
3 cover 2 screw(BVTT3 × 6)
1 two screws(case 3 TP2)
3 four screws(BVTP3 × 8)
1 wire (flat type) (21 core)(CN301)
2 connector(CN701)
4 CD mechanism deck(CDM63B-30BD60)
CDP-S3
8
3-4. MAIN BOARD
3-5. FRONT PANEL SECTION
2 connector(CN401)
1 wire (flat type) (21 core)(CN301)
2 two connectors(CN101, 102)
5 MAIN board
3 screw(BVTP3 × 8)
4 lug
3 screw(BVTP3 × 8)2 connector
(CN701)
3 two screws(BVTP3 × 8)
2 three screws(BVTP3 × 8)
3 two claws
1 connector(CN401)
4 front panel section
3 claw
CDP-S3
9
3-6. PANEL (L) BOARD, PANEL (R) BOARD
3-7. LID (CD)
5 two claws
4 four screws(BVTP2.6 × 8)
6 PANEL (R) board
1 five screws(BVTP2.6 × 8)
3 PANEL (L) board
2 two claws
3 lid (CD)
4 spring (CD)
1 screw(BVTP2.6 × 8)
2 bracket (LID) assy
10
CDP-S3SECTION 4TEST MODE
Note: Use flowing buttons in the test mode.no mark : Button of CD unit (CDP-S3)
*1 : Button of amplifier unit (TA-S7AV or TA-S3)*2 : Button of tuner unit (ST-S5 or ST-S3)
[CD Delivery Mode]• This mode moves the optical pick-up to the position durable to
vibration. Use this mode when returning the set to the customerafter repair.
Procedure:1. Press the I/1 *1 button to turn the power on.2. Turn the [FILE SELECT] *1 knob to set the CD function.3. While pressing the [EQ ON/OFF] *1 button, press the I/1 *1
button.4. The message “LOCK” is displayed on the fluorescent indica-
tor tube of tuner unit and turn the power off automatically, andthe CD delivery mode is set.
[GC Test Mode]Enter the GC Test ModeProcedure 1:1. Press the I/1 *1 button to turn the power on.2. While pressing the both [PLAY MODE] and [ ] buttons, press
the [ ] (DISC 1) button.3. LEDs and fluorescent indicator tube are all turned on of all
units.
Procedure 2:1. Press the I/1 *1 button to turn the power on.2. While pressing the both [STEREO/MONO] *2 and
[CINEMA STUDIO C] *1 buttons, press the [CLOCK/TIMER]*2 button.
3. LEDs and fluorescent indicator tube are all turned on of allunits.
Version Display ModeProcedure:1. Enter the GC test mode.2. Each time the [DISC 1] or [TUNER MEMORY] *2 button is
pressed, microcomputer or mechanism deck version is dis-played of each unit.
3. Press the [DISC 3] or [TUNING +] *2 button to detail is dis-played the version.
Key Check ModeProcedure:1. Enter the GC test mode.2. Press the [DISC 2] or [TUNING --] *2 button to set the key
check mode, and displays “K 0 J 0 V 0” on the fluorescentindicator tube of tuner unit.
3. All buttons are pressed of CD unit, all LEDs are blinking ofCD unit. (not change the display of fluorescent indicator tube)
Releasing the GC Test ModeTo release from this mode, press three buttons in the same manneras entering this mode or disconnect the power cord.
x
Z
[CD Service Mode]• This mode can run the CD sled motor optionally. Use this mode,
for instance, when cleaning the optical pick-up.Procedure:1. Press the I/1 *1 button to turn the power on.2. Turn the [FILE SELECT] *1 knob to set the CD function.3. While pressing the both [PLAY MODE] and [ ] buttons, press
the [ ] button.4. Set to the CD service mode.5. With the CD in stop status, press the [ ] button to move the
optical pick-up to outside track, or press the [ ] button toinside track.
6. To release from this mode, perform as follows.1) Move the optical pick-up to the most inside track.2) Disconnect the power cord.
Notes: • Always move the optical pick-up to most inside track whenreleasing from this mode. Otherwise, a disc will not be un-loaded.
• Do not run the sled motor excessively, otherwise the gear canbe chipped.
[CD Cancellation Mode of Repeat Limitation]• This mode can cancel the CD repeat limitation (5 times).Procedure:1. Press the I/1 *1 button to turn the power on.2. Turn the [FILE SELECT] *1 knob to set the CD function.3. While pressing the both [PLAY MODE] and [ ] buttons, press
the [REPEAT] button.4. CD repeat limitation is canceled.5. To release this mode, disconnect the power cord.
x
.
M
m
x
11
CDP-S3SECTION 5
ELECTRICAL ADJUSTMENTS
Note :1. CD Block is basically designed to operate without adjustment.
Therefore, check each item in order given.2. Use LUV-P01 (4-999-032-01) unless otherwise indicated.3. Use an oscilloscope with more than 10MΩ impedance.4. Clean the object lens by an applicator with neutral detergent
when the signal level is low than specified value with thefollowing checks.
S-Curve Check
Procedure :1. Connect an oscilloscope to TP (FEO).2. Connect between TP (FEI) and TP (DVC) ( 1.65 V) by lead
wire.3. Turn Power switch on.4. Load a disc (LUV-P01) and actuate the focus search. (In
consequence of open and close the disc tray, actuate the focussearch)
5. Confirm that the oscilloscope waveform (S-curve) issymmetrical between A and B. And confirm peak to peak levelwithin 2 ± 0.5 Vp-p.
6. After check, remove the lead wire connected in step 2.Note : • Try to measure several times to make sure than the ratio
of A : B or B : A is more than 10 : 7.• Take sweep time as long as possible and light up the
brightness to obtain best waveform.
RF Level Check
Procedure :1. Connect an oscilloscope CH1 to TP (RFDC) and CH2 to TP
(RFAC).2. Turn Power switch on.3. Load a disc (LUV-P01) and playback.4. Confirm that oscilloscope waveform is clear and check if RF
signal level is correct or not.Note : Clear RF signal waveform means that the shape “ ◊ ” can be clearly
distinguished at the center of the waveform.
BD boardOscilloscope
TP(FEO)TP(DVC)
symmetry
S-curve waveform
within 2 ±0.5Vp-p
A
B
TP(RFDC)TP(RFAC)
BD board oscilloscope
TP(DVC)
E-F Balance (1 Track jump) Check
Procedure :1. Connect an oscilloscope to TP (TEO) and TP (DVC).2. Turn Power switch on.3. Load a disc (LUV-P01) and playback the number nine track.4. Press the N button. (Becomes the 1 track jump mode.)5. Confirm that the level B and A (DC voltage) on the oscilloscope
waveform.
6. Adjust RV101 on the BD board so that the center of waveformbecomes the same voltage of DVC. (i.e. A=0V)
Adjustment Location:
[BD BOARD] (Conductor Side)
RF signal waveform
VOLT/DIV : 200mVTIME/DIV : 500ns
level : 0.65 ±0.15Vp-p (RFDC)1.1 ±0.4Vp-p (RFAC)
TP(TEO)TP(DVC)
BD boardoscilloscope
level=1.0 ±0.5Vp-p symmetry
A (DC voltage)
center ofwaveform
B
DVC
1 track jump waveform
TP (TEO)
TP(RFAC)
TP(FEI) TP
(RFDC)
TP (FEO)IC101
IC103
RV101
TP (DVC)
115
30
1
2021
40
60
8041
61
16
12
CDP-S3SECTION 6DIAGRAMS
C
B
These are omitted.
E
Q
B
These are omitted.
C E
Q
Note on Printed Wiring Boards:• X : parts extracted from the component side.• Y : parts extracted from the conductor side.• f : internal component.• : Pattern from the side which enables seeing.• Indication of transistor.
Note on Schematic Diagram:• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolyticsand tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.• f : internal component.• C : panel designation.
• A : B+ Line.• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-tion tolerances.
• Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal produc-tion tolerances.
• Circled numbers refer to waveforms.• Signal path.
J : CD PLAY
Note: The components identified by mark 0 or dotted linewith mark 0 are critical for safety.Replace only with part number specified.
6-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS(In addition to this, the necessary note is printed in each block)
13
CDP-S3
• Circuit Boards Location
DISC SENSOR board
BD board
IN OUT SW board
MOTOR board
DRIVER board
TRAY SENSOR board
MAIN board
PANEL (L) board
PANEL (R) board
14
CDP-S3
6-2. PRINTED WIRING BOARD – BD Section – • See page 13 for Circuit Boards Location.
There are a few cases that the part printed onthis diagram isn’t mounted in this model.
• SemiconductorLocation
Ref. No. Location
MAINBOARDCN301
M102(SLED)
TP(RFDC)
TP(RFAC)
TP(FEI)
TP(DVC) TP
(TEO
)
TP(FEO)
M101(SPINDLE)
A
D101 B-3
IC101 C-3IC102 B-2IC103 D-2
Q101 C-1Q102 A-3
(Page 18)
CDP-S3
1515
TP(RFDC)
TP (DVC)
TP(TEO)
TP(FEO)
TP (F
EI)
TP(RFAC)
IC B/D
IC B/D
IC B/D
MAINBOARDCN301
A
6-3. SCHEMATIC DIAGRAM – BD Section – • See page 22 for Waveforms. • See page 22 for IC Block Diagrams.
• Voltages and waveforms are dc with respect to groundunder no-signal conditions.no mark : CD PLAY
Note: The components identified by mark 0 or dotted linewith mark 0 are critical for safety.Replace only with part number specified.
(Page 19)
CDP-S3
1616
6-4. PRINTED WIRING BOARDS – CD CHANGER Section – • See page 13 for Circuit Boards Location.
MAINBOARDNO202
1 5
There are a few cases that the part isn't mounted in modelis printed on diagrams.
(Page 18)
CDP-S3
1717
6-5. SCHEMATIC DIAGRAM – CD CHANGER Section – • See page 22 for IC Block Diagram.
• Voltages and waveforms are dc with respect to groundunder no-signal conditions.no mark : CD STOP
BMAIN
BOARDNO202
IC731SUB TRAY1
HEIGHT SENSOR
IC732SUB TRAY2
HEIGHT SENSOR
IC733SUB TRAY3
HEIGHT SENSOR
IC751DISC INDETECT
RPI-321
RPI-321
RPI-321
(Page 19)
Ver 1.1
CDP-S3
1818
6-6. PRINTED WIRING BOARD – MAIN Section – • See page 13 for Circuit Boards Location.
Ref. No. LocationRef. No. Location
• Semiconductor Location
D501
C401
CN301
C101JW11
5
C501
CN102
CN101
CN401
D502
D503
D504
R403
FB305
FB410R409
C462
C463
C103
IC502
IC503
C513
C532
C523
D123
C500
R480
Q501
Q502
R448
R123
JW157
JW16
7
JW16
8
JW14
3
JW15
3
JW130
R460
C317
C318 C316
JW10
8
JW10
0
D514
JW10
3
X401
C531
JW137
R425
C319
R483
D511
C524
JW11
4
JW122
R419
JW12
6
R436
R401
R402
JW119
JW131
R413
C124
D513
JW11
3
C303
C522
R486
R485
JW11
0
C302
JW10
9
JW13
2
R487
JW10
4
C102IC102
CN103
C122
CD304
JW133
R495
R484
JW12
5
C260
C261
C255
JW121
JW12
7
JW12
8
JW16
3
JW12
9
FB416
JW11
2
JW118
JW117
JW106
C251
JW138
R497
C499JW171
JW124
JW14
4
CD302
JW14
5
JW14
9
R428
JW14
1
C498
R426
JW146
JW164
JW156
JW155
R433
JW160
C411
R432
JW123
R411
R427
C416
R417
JW12
0
JW13
9
CD30
3
JW14
2
D515R424
R429R430
R442
C425C427
R493
JW15
9
R456
R441
R443
R490
R438
R496
R445
R449
R450
R446
R447
R452
R500
R453
JW147
R473
R469
R465
R477
R481JW148
JW11
1
R444
JW16
9
R494
R482
R491
R489
R132
R133
R134L125
R492
JW16
2
JW165
JW13
5
JW17
0
R412
JW136
CD301
CD31
1
CD31
2
JW134
JW17
2
R459
R457
JW16
1
NO202
JW10
2
D105
VCD101
JW99
JW116
JW98
C301
JW17
5
JW17
7
JW15
0
C521
JW17
6
C125
JW14
0
CLP101
FB313
L310
FB314
FB315
C320 C311
FB310FB311
FB312
R451
JW17
8
C321
JW15
8
C314
R437 C313
CD31
3
C315
R440
R435
C304
JW15
4
C310
JW15
1
JW10
7
D512
C306
IC402
IC401
1 12
C118
C116
C107
CLP102
BD BOARDCN101A
PANEL (L) BOARDNO703C
DRIVER BOARDCN701B
1
9
1
1
14
8
EE
3
1
3
18
1
9
1
1
15
2
14
1
3
1-680-994-
11
(21)
(CHASSIS)
OPTICAL OUTTO ST-S3/S5
SYSTEM CONTROL 5TO TC-S3
SYSTEM CONTROL 3TO ST-S3/S5
MAIN BOARDA
B
C
D
1 2 3 4 5 6 7 8 9 10
D103 D-9D104 D-9D105 D-7D123 B-8D501 C-9D502 C-9D503 C-9D504 C-9D511 C-8D512 D-7D513 B-8D514 B-8
IC102 D-10IC401 C-4IC402 B-5IC502 C-8IC503 B-8
Q501 C-8Q502 C-8
(Page 14) (Page 16)
(Page 20)
CDP-S3
1919
6-7. SCHEMATIC DIAGRAM – MAIN Section – • See page 22 for Waveform.
• Voltages and waveforms are dc with respect to groundunder no-signal conditions.no mark : CD PLAY
Note: The components identified by mark 0 or dotted linewith mark 0 are critical for safety.Replace only with part number specified.
CD301
CD302
CD303
CD311
CD312
D501
CD313
C261
C260
D515C522 C521IC502
D514
D513
D512
C532 C531
C523C524
C310
FB312
FB313
FB311
FB310
C321
C301
C302
C304
C303
C311
C320
C313
C314
C315
C316
C317
C318
C319
C255
C251
C122
C500D504D503
D502
CN101
CN102
R1
34
R1
33
CN103
R132
VCD101
C501
R4
60
R4
52
R4
53
R5
00
R456R457
R450
R449
R448
R447
R446
R445
R444
R443
R442
R441
R440
R438
R437
R436
R435
TP439
R433
R432
C425
C427
R427
R425
R4
29
R430
R428R426
TP
42
7
TP
42
5
TP
42
3
TP
42
2
TP
42
1
TP
42
0
TP
41
8
R419 R424R417
X4
01
R413
C416
R411
R409
C411
TP
40
7
TP
40
6
TP
40
5
TP
40
4
TP
40
3
TP
40
2
TP
40
1
TP
45
6
TP
45
7
TP
45
8
TP
46
0
TP
46
1
TP
46
3
R451
C462
C463
FB416
Q502
Q501
D123
D511
C124
R123FB305
FB410
C513
R480R484
R485
R486
R487
R489
R490
R491
R493
R482
R483
R492
R494
R495
R497
R496
C498
C499
TP500
TP493
C401
FB315
FB314
R4
01
R4
03
R4
02
CN401
R481
R477
R473
R469
R465
IC503
D105 TP107
R412
CN301
IC402
C306
IC102
IC401
CD304
TP411
R459
JW99JW98
C118
C116
C103 C102 C101
C125
L125
L310
NO202
CLP102
C107
11ES2
0.022
0.022
11ES247010V 0.1TA78057S
11ES2
11ES2
11ES2
47010V 0.1
22010V
22010V
0.022
0.022
0.47 50V
0.0047
0.022
0.01
0.01
0.01
220p
100p
100p
100p
100p
100p
100p
0.022
0.022
0.022
0.111ES211ES2
11ES2
9P
8P
1k75
k
15P
75k
470016V
10
k
10
0
10
0
10
k
10k10k
100
100
100
100
100
100
100
100
100
10k
100
100
100
100
100
100
100
100p
100p
4.7k
4.7k
10
0
100
100k220k100 2.2k10k
16
MH
z
330
1050V
100
10k
150V
100
0.022
1050V
BA1A4M
RT1P137S
MTZA-2.2A
11ES2
0.1
100
47010V
100k100
100
100
100
100
100
100
150
10k
10k
4.7k
100
100
100
10k
0.022
0.022
0.022
10
0
10
0
10
0
9P
150
150
150
150
150
TA7807S
1SS133
10k
21P
SN74HCT04ANS-E05
TOTX140
M30620MAA-B31FP
100
100100
1
1
0.1 0.1 0.1
22010V
12P
JW
84
85
86
87
24
33
35
37
40
42
43
44
45
46
47
48
49
26
28
12
29
30
19
32
19
32
33
40
37
42
35
43
28
24
26
51
53
50
51
53
36
36
95
94
97
97
95
59
59
84
85
86
87
94
52
91
90
89
91
90
89
52
47
46
48
45
44
30
38
A32
A36
A19
A19
A32
65
69
73
77
81
65
69
73
77
81
A36
49
50
29
38
12
MRESET
I2C-CLK
I2C-DATA
VCD L-IN
VCD R-IN
V-MUTE
DGND(TC)
AGND(CD)
AC
AC
HESO-GND
HESO-GND
EVER+5V
UNREG(TC)
MGND(TC)
MGND(TC)
GN
D
SIG
+3
.3V
SHASSIS GND
RE
SE
T
X-O
UT
VS
S
X-I
N
VC
C
NM
I
SC
OR
IIC
-CL
K
SQ-CLK
CD-DATA
CD-CLK
HOLD
XLT
XRST
R/P
B/P
AS
MODEL-IN
LOAD-OUT
LOAD-IN
OPEN
CLOSE
B-T
RIG
BU
PW
M 3
BU
PW
M 2
BU
PW
M 1
SO
FT
-TE
ST
VC
C
VS
S
AVSS
VREF
AVCC
BY
TE
CN
VS
S
KEY3
T-SENS3
T-SENS2
T-SENS1
SENS
RTS1
KEY2(TC)
KEY1(CD)
KEY0(CD)
DIS
C-S
EN
S
LED_PAUSE
LE
D_
PL
AY
LE
D_
DIS
C3
LE
D_
DIS
C2
LE
D_
DIS
C1
EC
O C
HE
CK
DA
TA
IIC
-
CLK
LAT
ASHUT
BSHUT
BHALF
DATA-OUT
DATA-IN
BTRIG
ATRIG
REC/PB/PAS
MGND
DGND
KEY2
SGND
UNREG
SENS
SCOR
PWM1
PWM2
PWM3
MGND
DVDD
DOUT
DGND
AGND
AVDD
XRST
DATA
XLT
CLOK
LDON
SQSO
SQCK
+7V
DISC-SENS
IN-SW
OUT-SW
TRAYSENS3
TRAYSENS2
TRAYSENS1
DGND
D+5V
LOD-POS
LOD-NEG
MGND
M+7V
(CHASSIS)OPTICAL
TRANSCEIVER
+5.6V REGULATOR
GIO
GIO
+7V REGULATOR
Q501,502
B+ SWITCH
OPTICAL OUT
SYSTEM CONTROL 3
SYSTEM CONTROL 5
TO TC-S3
SYSTEM CONTROLLER
CD POWER
TO ST-S3/S5
LEVEL SHIFT
TO ST-S3/S5
LE
D_
PL
AY
LED_PAUSE
LED_PAUSE
LED_
PLAY
LE
D_
PL
AY
LE
D_
DIS
C3
LE
D_
DIS
C3
LE
D_
DIS
C3
LE
D_
DIS
C2
LE
D_
DIS
C2
LE
D_
DIS
C2
LE
D_
DIS
C1
LE
D_
DIS
C1
LE
D_
DIS
C1
A-T
RIG
DATA-IN
SQ-
B-HALF
B-SHUT
A-SHUT
LED_PAUSE
EXP-CLK
EXP-LAT
EXP-OUT DATA
EXP-IN DATA
k
k
LOUT
ROUT
5.6µH
220µH
(Page 15)
(Page 17)
(Page 21)
CDP-S3
2020
6-8. PRINTED WIRING BOARDS – PANEL Section – • See page 13 for Circuit Boards Location.
S711S712
S714S713
S715 S716 S717
D701 D702D703 D704 D705
NO702
R713
R711
R712
R714
R715
R716
NO703
R710
S708S707
S706 S705 S704
S703S702S701
NO701
R701 R702 R703
R704R705
R706 R707
R700
C MAIN BOARDCN401
19
PANEL (L) BOARD
PANEL (R) BOARD
1-680-995-
11
(21) 1-680-996-
11
(21)
12
12
M
>
x
X
.
N
m
D701, S716
D702, S7173 2 1
Z
(DISC 3)
Z
DISC 3 DISC 2 DISC 1
PLAY MODEREPEAT
(DISC 2)
Z
(DISC 1)
(Page 18)
CDP-S3
2121
6-9. SCHEMATIC DIAGRAM – PANEL Section –
(Page 19)
D701
D702
D703
D704
D705
R710R711R712R713R714R715R716
R707 R706 R705 R704 R703 R702 R701 R700
S702 S701S703S704S705S706S707S708
CNW703
CN702
CN701
S711S712S714 S713S715S716S717
SEL5923A
SEL5423E
SEL5923A
SEL5923A
SEL5923A
2703304705606801k1.2k
1.8k 1.2k 1k 680 560 470 330 270
9P
2P
2P
DISC 3DISC 1 DISC 2
(DISC 1)(DISC 3) (DISC 2)
REPEATPLAY MODE
CDP-S3
2222
• Waveforms– BD Board –
1 IC101 ta (RFAC) (CD Play mode)
1.1 Vp-p
2 IC101 ra (TE) (CD Play mode)
Approx.0.4 Vp-p
3 IC101 el (FE) (CD Play mode)
Approx.0.3 Vp-p
qa IC401 qd (X-OUT)
2.6 Vp-p
63 ns
4 IC101 wh (MDP)
2.5 Vp-p
7.5 µs
– MAIN Board –
IC102 BA5974FM-E2
• IC Block Diagrams– BD Board –
IC101 CXD3017Q
TERFDC
CEIGEN
AVSS
0
ADIO
AVDD
0
CLTV
FILO
AVSS
3
VSS
AVDD
3
DOUT
VDD
PCO
FILI
ASYO
ASYI
RFAC
BIAS
SSTP
DFCTMIRR
MDPLOCK
FOK
SFDR
VSS
TEST
FRDR
FEVC
COUT
SE
XTSLTES1
SRDRTFDR
FFDRTRDR
21
7071
6869
6667
64
65
62
61
63
7374
72
75
76
7778
7980
4
XRST
3
SQCK
SQSO
5 9876
5660 53545559 5758 5152 484950 47 444546 43 4142
XLAT
CLOK
SENS
SYSM
DATA
XUGF
XPCK GF
S
C2PO
WFC
K
10 11 12 13 14 15 16 17 18 19 20
21
222324
2526
3233
3031
3637
3435
3940
38
28
27
29
SPOA
ATSK
SCLK
VDD
SCOR
SPOB
XLON
XTAI
XVDD
EMPH
AVDD1AOUT1
AIN1
XTAOXVSS
AIN2
AOUT2AVDD2
RMUT
LOUT2
LOUT1
BCK
LRCK
PCMD
LMUT
AVSS1AVSS2
CPUINTERFACE
SERVO AUTOSEQUENCER
SERIAL ININTERFACE
OVER SAMPLINGDIGITAL FILTER
3rd ORDERNOISE SHAPER
PWM PWM
EFMDEMODULATOR
TIMINGLOGIC
DIGITALOUT
D/AINTERFACE
DIGITALPLL
ASYMMETRYCORRECTOR
CLOCKGENERATOR
MIRR, DFCT,FOK
DETECTOR
DIGITALCLV
SUBCODEPROCESSOR
SERVOINTERFACE
SERVO DSP
FOCUSSERVO
TRACKINGSERVO
SLEDSERVO
PWM GENERATOR
FOCUS PWMGENERATOR
TRACKINGPWM GENERATOR
SLED PWMGENERATOR
16KRAM
ERRORCORRECTOR
INTE
RNAL
BUS
A/DCONVERTER
OPERATIONALAMPLIFIER
ANALOG SWITCH
LEVEL SHIFT
INTERFACE
INTERFACE
INTERFACE
1 2 3 4 5 6 7 8 9 10 11 12 13 14
202122232425262728 19 18 17 16 15
F
RRF F
RRF
RR
F
FMUTE
THERMALSHUTDOWN
VREF
OUT
VREF
IN
POW
VCC
CH1F
IN
CH1R
IN
CH2F
IN
CH2R
IN
CH2O
UTR
CH2O
UTF
CH1O
UTR
CH1O
UTF
CAPA
IN1
CAPA
IN2
GND
PRFV
CC
MUT
E
POW
VCC
CH4S
IN'
CH4S
IN
CH4B
IN
CH3F
IN
CH3R
IN
CH3O
UTR
CH3O
UTF
CH4O
UTR
CH4O
UTF
CAPA
IN3
GND
23
CDP-S3
– DRIVER Board –
IC701 BA6956AN
1 2 3 4 5 6 7 8 9
CONTROL LOGIC
TSD
VREF
OUT2
OUT1
RNF
VM VCC
FIN
GND
RIN
IC103 CXA2581N-T4
RW/ROM
RW/ROM
EQ ON/OFF
VOFST
VOFSTDVC
VC
VC
VC
RW/ROM
VC
DVC
3029
28+–+
–
DVCVCC
DVC
27
262524
RW/ROM
EQ
23
22
21
20
19
RFACVCA
VCC
+–
DVC
+–
+–
RW/ROM
VC
RW/ROM
DVC
+–
3
A
B
C
D
BC
A
A
A
BCD
B C D D
+–
1
2 APC AMP
5
6789
4RFAC
SUMMINGAMP
RW/ROM
APC-OFF(Hi-Z)
RW/ROM(H/L)
VOFST
VC
RW/ROM
+–
10
11
GM
GM
18
17
16
B
D
A
C
13
14
15
12
EQ IN
LD
PD
GND
ABCD
AC SUM
E
F
DVCC
DVC
RFAC
SW
DC OFSTRFDCI
RFDCO
VC
RFCVFCBST
RFG
VCC
CEI
CE
TE BAL
TE
FEI
FE
24
CDP-S3
6-10. IC PIN FUNCTION DESCRIPTION
• MAIN BOARD IC401 M30620MAA-B31FP (SYSTEM CONTROLLER)
Pin No. Pin Name I/O Description
1 to 7 — — Not used (open)
8 BYTE IExternal data bus line byte selection signal input “L”: 16 bits, “H”: 8 bitsNot used (fixed at “L”)
9 CNVSS — To flash memory connector
10 — — Not used (fixed at “L”)
11 — — Not used (open)
12 RESET I Reset signal input from the tuner unit (ST-S3/S5)
13 X-OUT O System clock output terminal (16 MHz)
14 VSS — Ground terminal
15 X-IN I System clock input terminal (16 MHz)
16 VCC — Power supply terminal (+5V)
17 NMI I Non-maskable interrupt input terminal (fixed at “H” in this set)
18 — — Not used (open)
19 SCOR I Subcode sync (S0+S1) detection signal input from the CXD3017Q (IC101)
20 to 23 — — Not used (open)
24 BU PWM 3 O RFDC PWM signal output to the CXA2581N (IC103)
25 — — Not used (open)
26 BU PWM 2 O Tracking error PWM signal output to the CXA2581N (IC103)
27 — — Not used (open)
28 BU PWM 1 O Focus error PWM signal output to the CXA2581N (IC103)
29 IIC-CLK I/OCommunication data reading clock signal input or transfer clock signal output with the tuner unit (ST-S3/S5)
30 IIC-DATA I/O Communication data bus with the tuner system (ST-S3/S5)
31 — — Not used
32 SQ-DATA-IN I Subcode Q data input from the CXD3017Q (IC101)
33 SQ-CLK O Subcode Q data reading clock signal output to the CXD3017Q (IC101)
34 RTS1 — Not used
35 CD-DATA O CD decode data output to the CXD3017Q (IC101)
36 SENS I Internal status (SENSE) signal input from the CXD3017Q (IC101)
37 CD-CLK O Serial data transfer clock signal output to the CXD3017Q (IC101)
38 CD POWER O Power on/off control signal output for the CD mechanism deck section “L”: standby, “H”: power on
39 — — Not used (open)
40 HOLD O Automatic power control hold signal output to the CXA2581N (IC103)
41 — — Not used (fixed at “L”)
42 XLT O Serial data latch pulse output to the CXD3017Q (IC101)
43 XRST O Reset signal output to the CXD3017Q (IC101)
44 LOAD-IN O Loading motor drive signal (load-in direction) output the motor driver (IC701)
45 LOAD-OUT O Loading motor drive signal (load-out direction) output the motor driver (IC701)
46 OPEN I Sub tray load in/out detect switch (S742) input “L”: sub tray is chucking position
47 CLOSE I Sub tray load in/out detect switch (S742) input “L”: sub tray slides out of chucking position
48 T-SENS1 IDetection input from the disc tray 1 height sensor (IC731) “H”: disc tray 1 position is chucking position
49 T-SENS2 IDetection input from the disc tray 2 height sensor (IC732) “H”: disc tray 2 position is chucking position
25
CDP-S3
Pin No. Pin Name I/O Description
50 T-SENS3 IDetection input from the disc tray 3 height sensor (IC733) “H”: disc tray 3 position is chucking position
51 — — Not used (fixed at “H”)
52 DISC-SENS I Detection input from the disc in detect sensor (IC751)
53 B-TRIG O Deck-B trigger plunger drive signal output to the tape deck unit (TC-S3) “H”: trigger plunger on
54 ECO CHECK — Not used (fixed at “H”)
55 A-TRIG O Deck-A trigger plunger drive signal output to the tape deck unit (TC-S3) “H”: trigger plunger on
56 to 58 — — Not used (open)
59 R/PB/PASS O Recording/playback/pass selection signal output to the tape deck unit (TC-S3) “L”: recording, center voltage: playback, “H”: pass
60, 61 — — Not used (open)
62 VCC — Power supply terminal (+5V)
63 SOFT-TEST O For software check terminal
64 VSS — Ground terminal
65 to 68 LED_DISC1 O LED drive signal output of the 1 indicator (D705) “L”: LED on
69 to 72 LED_DISC2 O LED drive signal output of the 2 indicator (D704) “L”: LED on
73 to 76 LED_DISC3 O LED drive signal output of the 3 indicator (D703) “L”: LED on
77 to 80 LED_PLAY O LED drive signal output of the N indicator (D702) “L”: LED on
81 to 83 LED_PAUSE O LED drive signal output of the X indicator (D701) “L”: LED on
84 EXP-IN DATA I Serial data input from the tape deck unit (TC-S3)
85 EXP-OUT DATA O Serial data output to the tape deck unit (TC-S3)
86 EXP-LAT O Serial data latch pulse signal output to the tape deck unit (TC-S3)
87 EXP-CLK O Serial data transfer clock signal output to the tape deck unit (TC-S3)
88 LED_PAUSE O LED drive signal output of the X indicator (D701) “L”: LED on
89 A-SHUT I Shut off (desk-A) detection signal input from the tape deck unit (TC-S3)
90 B-SHUT I Shut off (desk-B) detection signal input from the tape deck unit (TC-S3)
91 B-HALF I Detection input from the deck-B cassette detect switch of the tape deck unit (TC-S3) “L”: cassette in
92 MODEL-IN I Model destination setting terminal
93 KEY3 — Not used (open)
94 KEY2 (TC) I Key input from the tape deck unit (TC-S3) (A/D input)
95 KEY1 (CD) I Key input terminal (A/D input) (S711 to S717) m, M , ., >, x, X, N keys input
96 AVSS — Ground terminal (for A/D conversion)
97 KEY1 (CD) IKey input terminal (A/D input) (S701 to S708) DISC 3, DISC 2, DISC 1, Z (DISC1), Z
(DISC2), Z (DISC3), REPEAT, PLAY MODE keys input
98 VREF I Reference voltage (+5V) input terminal (for A/D converter)
99 AVCC — Power supply terminal (+5V) (for A/D conversion)
100 — — Not used (open)
26
CDP-S3
7-1. GENERAL SECTION
SECTION 7EXPLODED VIEWS
The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
• Items marked “*” are not stocked since theyare seldom required for routine service. Somedelay should be anticipated when orderingthese items.
• The mechanical parts with no reference num-ber in the exploded views are not supplied.
NOTE:• -XX and -X mean standardized parts, so they
may have some difference from the originalone.
• Color Indication of Appearance PartsExample:KNOB, BALANCE (WHITE) . . . (RED)
↑ ↑Parts Color Cabinet's Color
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 X-4953-613-1 PANEL ASSY, FRONT2 4-233-136-01 LID (CD)3 4-233-147-01 SPRING (CD)4 4-951-620-01 SCREW (2.6X8), +BVTP5 1-680-996-11 PANEL (R) BOARD
6 1-680-995-11 PANEL (L) BOARD7 3-363-099-21 SCREW (CASE 3 TP2)8 4-233-134-11 COVER9 1-823-055-11 WIRE (FLAT TYPE) (21 CORE)
10 A-4725-658-A MAIN BOARD, COMPLETE11 1-757-633-11 CORD (WITH CONNECTOR) 17P12 4-233-135-01 PANEL, BACK (AEP, UK)12 4-233-135-11 PANEL, BACK (Korea, Australian)12 4-233-135-31 PANEL, BACK (Mexican)
13 3-970-608-01 SUMITITE (B3), +BV14 4-965-822-01 FOOT#1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S#2 7-685-871-01 SCREW +BVTT 3X6 (S)
not supplied
3
not supplied
not supplied
not supplied
not supplied
not supplied #1
#1
#1
#1
#1
#2
CDM63B-30BD60
2
4
5
4
6
414
13
12
11
10
9
7
8
7
1
27
CDP-S3
7-2. CD MECHANISM DECK SECTION-1(CDM63B-30BD60)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
501 4-218-253-01 SCREW (M2.6), +BTTP502 4-228-996-01 SPRING (R), TORSION503 4-228-995-01 SPRING (L), TORSION504 4-228-972-02 TRAY (MAIN)505 4-231-971-01 PULLEY (30B), CHUCKING
506 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING507 4-228-414-01 BRACKET (YOKE)508 4-228-980-01 SPRING (STOCKER), LEAF509 4-228-981-02 STOPPER (TRAY)510 4-228-963-01 SLIDER (STOCKER. L)
511 4-228-964-01 SLIDER (STOCKER. R)512 4-228-970-02 TRAY (SUB)513 4-229-001-01 HOLDER (SENSOR)
514 4-228-975-02 COVER (TRAY. L)515 4-228-978-02 COVER (TRAY. R)516 4-228-970-12 TRAY (SUB)517 4-228-970-22 TRAY (SUB)518 X-4953-307-1 PULLEY (A) ASSY, CHUCKING
519 4-234-423-01 SPRING (STOCKER L), LEAF520 1-678-457-11 TRAY SENSOR BOARD521 4-228-986-02 RACK (TRAY.L)522 4-228-990-03 LEVER (SUB.L)523 4-228-991-03 LEVER (SUB.R)
524 4-228-987-02 RACK (TRAY.R)525 4-228-993-05 SLIDER (LOADING)
501
501
502
504
525
not supplied
not supplied
522 523
524
521
501
not supplied
not supplied
not supplied
not supplied
514
515
503503
501518
501
505
501
506507
506
510
509
501
501
516
517
512
501
519 508501
509
511
513
501
520
501
501
501
B
B
A
A
Ver 1.3
28
CDP-S3
7-3. CD MECHANISM DECK SECTION-2(CDM63B-30BD60)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
551 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING552 4-229-002-02 GEAR (SLIDER)553 4-218-254-21 SCREW (M2.6), +PTPWH554 4-228-971-01 CAM555 4-228-974-02 RACK (CENTER)
556 4-218-253-01 SCREW (M2.6), +BTTP557 4-228-969-02 SPRING (TABLE), LEAF558 4-228-977-01 SLIDER (BU. L)559 4-951-620-01 SCREW (2.6X8), +BVTP560 4-227-045-11 SPRING (INSULATOR), COIL
561 4-231-451-01 INSULATOR (BU-30)562 4-231-151-01 STOPPER (BU)563 4-231-517-03 HOLDER (BU30)564 4-228-985-01 GEAR (PULLEY)565 4-228-997-02 GEAR (CAM)
566 1-678-460-11 DRIVER BOARD
567 4-228-968-01 BELT568 4-228-998-01 GEAR (DETECTION)569 4-228-976-01 SLIDER (BU. R)570 1-678-461-11 MOTOR BOARD571 X-4952-971-2 MOTOR ASSY
572 4-228-999-02 LEVER (MAIN. L)573 4-229-000-02 LEVER (MAIN. R)574 4-227-899-01 SCREW (DIA. 12), FLOATING575 4-229-003-01 PULLEY576 4-228-988-01 CHASSIS
577 4-218-253-61 SCREW (M2.6), +BTTP578 4-218-253-71 SCREW (M2.6), +BTTP579 1-678-462-11 IN OUT SW BOARD580 1-678-463-11 DISC SENSOR BOARDM721 1-541-632-12 MOTOR, DC (LOADING)
BU-30BD60
556
580
563
not supplied
not supplied
not supplied
574
551
556
558
557
557576
552
555
578
554
551 553
551552
551
571
570
551
M721
556
556577
577
572573
569
566
556 579
568
A
A
553
575
553
553
564
551
567
561 561
560
560
561
561
565
578
562
560
562559
551
29
CDP-S3
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
601 3-531-576-11 RIVET602 A-4725-531-A BD BOARD, COMPLETE603 4-233-832-01 GEAR (LB)604 4-233-831-01 GEAR (LA)
605 1-757-710-11 WIRE (FLAT TYPE) (16 CORE)0606 A-4735-188-A BU-30 (60) ASSY
#5 7-627-853-28 SCREW, PRECISION +P 2X3 TYPE3
7-4. BASE UNIT SECTION(BU-30BD60)
The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
not supplied
not supplied
605
602
601
604
603not supplied
#5 #5
606
30
CDP-S3
BDSECTION 8
ELECTRICAL PARTS LIST
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
NOTE:• Due to standardization, replacements in the
parts list may be different from the parts speci-fied in the diagrams or the components usedon the set.
• -XX and -X mean standardized parts, so theymay have some difference from the originalone.
• RESISTORSAll resistors are in ohms.METAL: Metal-film resistor.METAL OXIDE: Metal oxide-film resistor.F: nonflammable
• Items marked “*” are not stocked since theyare seldom required for routine service.Some delay should be anticipated when order-ing these items.
• SEMICONDUCTORSIn each case, u: µ, for example:uA. . : µA. . uPA. . : µPA. .uPB. . : µPB. . uPC. . : µPC. .uPD. . : µPD. .
• CAPACITORSuF: µF
• COILSuH: µH
The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
When indicating parts by referencenumber, please include the board.
A-4725-531-A BD BOARD, COMPLETE*******************
< CAPACITOR >
C101 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50VC102 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC103 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC104 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC108 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C109 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50VC110 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50VC111 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC112 1-109-982-11 CERAMIC CHIP 1uF 10% 10VC114 1-163-038-11 CERAMIC CHIP 0.1uF 25V
C116 1-104-665-11 ELECT 100uF 20% 10VC117 1-104-665-11 ELECT 100uF 20% 10VC118 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC121 1-163-038-11 CERAMIC CHIP 0.1uF 25VC122 1-124-584-00 ELECT 100uF 20% 10V
C123 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC124 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16VC125 1-163-038-11 CERAMIC CHIP 0.1uF 25VC126 1-163-038-11 CERAMIC CHIP 0.1uF 25VC127 1-124-584-00 ELECT 100uF 20% 10V
C129 1-162-974-11 CERAMIC CHIP 0.01uF 50VC130 1-163-038-11 CERAMIC CHIP 0.1uF 25VC131 1-104-665-11 ELECT 100uF 20% 10VC133 1-162-921-11 CERAMIC CHIP 33PF 5% 50VC143 1-163-038-11 CERAMIC CHIP 0.1uF 25V
C145 1-163-038-11 CERAMIC CHIP 0.1uF 25VC153 1-163-038-11 CERAMIC CHIP 0.1uF 25VC159 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC162 1-104-665-11 ELECT 100uF 20% 10VC165 1-163-038-11 CERAMIC CHIP 0.1uF 25V
C167 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC168 1-162-921-11 CERAMIC CHIP 33PF 5% 50VC171 1-115-412-11 CERAMIC CHIP 680PF 5% 25VC172 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC181 1-115-412-11 CERAMIC CHIP 680PF 5% 25V
C182 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC183 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC184 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC185 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16VC190 1-115-156-11 CERAMIC CHIP 1uF 10V
C191 1-124-584-00 ELECT 100uF 20% 10VC192 1-163-038-11 CERAMIC CHIP 0.1uF 25VC193 1-104-665-11 ELECT 100uF 20% 10VC194 1-163-038-11 CERAMIC CHIP 0.1uF 25VC195 1-163-038-11 CERAMIC CHIP 0.1uF 25V
C196 1-163-038-11 CERAMIC CHIP 0.1uF 25VC197 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC198 1-124-584-00 ELECT 100uF 20% 10V
< CONNECTOR >
CN101 1-568-864-11 CONNECTOR, FFC 21PCN102 1-793-907-11 CONNECTOR, FFC/FPC 16P
< DIODE >
D101 8-719-422-12 DIODE UDZ-TE-17-3.9B
< FERRITE BEAD >
FB101 1-500-445-21 FERRITE 0uHFB102 1-500-445-21 FERRITE 0uH
< IC >
IC101 8-752-402-31 IC CXD3017QIC102 8-759-827-41 IC BA5974FM-E2IC103 8-752-089-74 IC CXA2581N-T4
< SHORT >
JR101 1-216-295-11 SHORT 0JR102 1-216-295-11 SHORT 0JR103 1-216-295-11 SHORT 0JR104 1-216-295-11 SHORT 0JR105 1-216-295-11 SHORT 0
JR106 1-216-295-11 SHORT 0JR122 1-216-296-11 SHORT 0JR123 1-216-296-11 SHORT 0JR124 1-216-296-11 SHORT 0JR125 1-216-296-11 SHORT 0
< COIL >
L101 1-469-553-21 INDUCTOR 4.7uH
< TRANSISTOR >
Q101 8-729-010-08 TRANSISTOR MSB710-RT1
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
31
CDP-S3
BD DISC SENSOR DRIVER IN OUT SW MAIN
Q102 8-729-920-85 TRANSISTOR 2SD1664-T100-QR
< RESISTOR >
R101 1-216-049-11 RES-CHIP 1K 5% 1/10WR102 1-216-097-11 RES-CHIP 100K 5% 1/10WR103 1-216-077-00 RES-CHIP 15K 5% 1/10WR104 1-216-085-00 METAL CHIP 33K 5% 1/10WR105 1-216-049-11 RES-CHIP 1K 5% 1/10W
R106 1-216-049-11 RES-CHIP 1K 5% 1/10WR107 1-216-073-00 METAL CHIP 10K 5% 1/10WR108 1-216-061-00 METAL CHIP 3.3K 5% 1/10WR109 1-216-121-11 RES-CHIP 1M 5% 1/10WR111 1-216-099-00 METAL CHIP 120K 5% 1/10W
R114 1-218-745-11 RES-CHIP 160K 5% 1/16WR116 1-216-001-00 METAL CHIP 10 5% 1/10WR117 1-216-049-11 RES-CHIP 1K 5% 1/10WR118 1-216-025-11 RES-CHIP 100 5% 1/10WR119 1-216-059-00 METAL CHIP 2.7K 5% 1/10W
R120 1-216-077-00 RES-CHIP 15K 5% 1/10WR122 1-216-097-11 RES-CHIP 100K 5% 1/10WR123 1-216-073-00 METAL CHIP 10K 5% 1/10WR124 1-216-097-11 RES-CHIP 100K 5% 1/10WR131 1-216-033-00 METAL CHIP 220 5% 1/10W
R143 1-216-085-00 METAL CHIP 33K 5% 1/10WR144 1-216-085-00 METAL CHIP 33K 5% 1/10WR147 1-216-059-00 METAL CHIP 2.7K 5% 1/10WR148 1-216-001-00 METAL CHIP 10 5% 1/10WR149 1-216-001-00 METAL CHIP 10 5% 1/10W
R158 1-216-083-00 METAL CHIP 27K 5% 1/10WR159 1-216-083-00 METAL CHIP 27K 5% 1/10WR162 1-216-097-11 RES-CHIP 100K 5% 1/10WR171 1-216-081-00 METAL CHIP 22K 5% 1/10WR172 1-216-081-00 METAL CHIP 22K 5% 1/10W
R173 1-216-081-00 METAL CHIP 22K 5% 1/10WR181 1-216-081-00 METAL CHIP 22K 5% 1/10WR182 1-216-081-00 METAL CHIP 22K 5% 1/10WR183 1-216-081-00 METAL CHIP 22K 5% 1/10WR190 1-216-033-00 METAL CHIP 220 5% 1/10W
R191 1-216-085-00 METAL CHIP 33K 5% 1/10WR192 1-216-085-00 METAL CHIP 33K 5% 1/10WR193 1-216-099-00 METAL CHIP 120K 5% 1/10WR194 1-216-097-11 RES-CHIP 100K 5% 1/10WR195 1-216-113-00 METAL CHIP 470K 5% 1/10W
R196 1-216-057-00 METAL CHIP 2.2K 5% 1/10WR198 1-216-295-11 SHORT 0
< COMPOSITION CIRCUIT BLOCK >
RN101 1-233-576-11 RES, CHIP NETWORK 100
< VARIABLE RESISTOR >
RV101 1-238-602-11 RES, ADJ, CARBON 47K
< VIBRATOR >
X101 1-579-280-11 VIBRATOR, CRYSTAL (16.9344MHz)**************************************************************
1-678-463-11 DISC SENSOR BOARD******************
< PHOTO REFLECTOR >
IC751 8-749-924-30 PHOTO REFLECTOR GP2S28 (DISC IN DETECT)
< RESISTOR >
R751 1-249-407-11 CARBON 150 5% 1/4W**************************************************************
1-678-460-11 DRIVER BOARD*************
< CAPACITOR >
C701 1-124-261-00 ELECT 10uF 20% 50VC705 1-124-261-00 ELECT 10uF 20% 50VC706 1-164-159-11 CERAMIC 0.1uF 50VC707 1-164-159-11 CERAMIC 0.1uF 50V
< CONNECTOR >
CN701 1-785-324-11 PIN, CONNECTOR (STRAIGHT) 12PCN702 1-785-328-11 PIN, CONNECTOR (LIGHT ANGRE) 2PCN703 1-785-331-11 PIN, CONNECTOR (LIGHT ANGLE) 5PCN704 1-785-329-11 PIN, CONNECTOR (LIGHT ANGLE) 3PCN705 1-785-329-21 PIN, CONNECTOR (LIGHT ANGLE) 3P
< IC >
IC701 8-759-598-69 IC BA6956AN
< TRANSISTOR >
Q701 8-729-029-66 TRANSISTOR RT1N141S-TP
< RESISTOR >
R701 1-249-429-11 CARBON 10K 5% 1/4WR702 1-249-401-11 CARBON 47 5% 1/4WR705 1-249-435-11 CARBON 33K 5% 1/4WR706 1-249-417-11 CARBON 1K 5% 1/4WR707 1-249-429-11 CARBON 10K 5% 1/4W
**************************************************************
1-678-462-11 IN OUT SW BOARD****************
< SWITCH >
S741 1-771-821-11 SWITCH, PUSH (1 KEY) (IN)S742 1-771-821-11 SWITCH, PUSH (1 KEY) (OUT)
**************************************************************
A-4725-658-A MAIN BOARD, COMPLETE*********************
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
< CAPACITOR/RESISTOR >
C101 1-164-159-11 CERAMIC 0.1uF 50VC102 1-164-159-11 CERAMIC 0.1uF 50VC103 1-164-159-11 CERAMIC 0.1uF 50VC116 1-249-417-11 CARBON 1K 5% 1/4WC118 1-249-417-11 CARBON 1K 5% 1/4W
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
32
CDP-S3
MAIN
D513 8-719-024-99 DIODE 11ES2-NTA2BD514 8-719-024-99 DIODE 11ES2-NTA2B
D515 8-719-024-99 DIODE 11ES2-NTA2B
< FERRITE BEAD >
FB305 1-412-473-21 INDUCTOR 0uHFB310 1-412-473-21 INDUCTOR 0uHFB311 1-412-473-21 INDUCTOR 0uHFB312 1-412-473-21 INDUCTOR 0uHFB313 1-412-473-21 INDUCTOR 0uH
FB314 1-412-473-21 INDUCTOR 0uHFB315 1-412-473-21 INDUCTOR 0uHFB410 1-412-473-21 INDUCTOR 0uHFB416 1-412-473-21 INDUCTOR 0uH
< IC >
IC102 8-749-019-13 IC TOTX140 (OPTICAL OUT TO ST-S3/S5)IC401 8-759-827-46 IC M30620MAA-B31FPIC402 8-759-269-09 IC SN74HCT04ANS-E05IC502 8-759-158-62 IC TA78057SIC503 8-759-071-48 IC TA7807S
< RESISTOR >
JW98 1-247-807-31 CARBON 100 5% 1/4WJW99 1-247-807-31 CARBON 100 5% 1/4W
< COIL >
L125 1-410-336-11 INDUCTOR 220uHL310 1-410-467-11 INDUCTOR 5.6uH
< TRANSISTOR >
Q501 8-729-049-79 TRANSISTOR RT1P137S-TPQ502 8-729-900-80 TRANSISTOR BA1A4M-TP
< RESISTOR >
R123 1-247-807-31 CARBON 100 5% 1/4WR132 1-247-876-11 CARBON 75K 5% 1/4WR133 1-247-876-11 CARBON 75K 5% 1/4WR134 1-249-417-11 CARBON 1K 5% 1/4WR401 1-247-807-31 CARBON 100 5% 1/4W
R402 1-247-807-31 CARBON 100 5% 1/4WR403 1-247-807-31 CARBON 100 5% 1/4WR409 1-249-429-11 CARBON 10K 5% 1/4WR411 1-247-807-31 CARBON 100 5% 1/4WR412 1-249-429-11 CARBON 10K 5% 1/4W
R413 1-249-411-11 CARBON 330 5% 1/4WR417 1-249-429-11 CARBON 10K 5% 1/4WR419 1-247-807-31 CARBON 100 5% 1/4WR424 1-249-421-11 CARBON 2.2K 5% 1/4WR425 1-249-425-11 CARBON 4.7K 5% 1/4W
R426 1-247-887-00 CARBON 220K 5% 1/4WR427 1-249-425-11 CARBON 4.7K 5% 1/4WR428 1-249-441-11 CARBON 100K 5% 1/4WR429 1-247-807-31 CARBON 100 5% 1/4WR430 1-247-807-31 CARBON 100 5% 1/4W
R432 1-247-807-31 CARBON 100 5% 1/4WR433 1-247-807-31 CARBON 100 5% 1/4W
C122 1-161-494-00 CERAMIC 0.022uF 25VC124 1-164-159-11 CERAMIC 0.1uF 50VC125 1-126-923-11 ELECT 220uF 20% 10VC251 1-161-494-00 CERAMIC 0.022uF 25VC255 1-161-494-00 CERAMIC 0.022uF 25V
C260 1-161-494-00 CERAMIC 0.022uF 25VC261 1-161-494-00 CERAMIC 0.022uF 25VC301 1-126-959-11 ELECT 0.47uF 20% 50VC302 1-162-600-11 CERAMIC 0.0047uF 20% 16VC303 1-162-306-11 CERAMIC 0.01uF 20% 16V
C304 1-161-494-00 CERAMIC 0.022uF 25VC310 1-161-494-00 CERAMIC 0.022uF 25VC311 1-162-306-11 CERAMIC 0.01uF 20% 16VC313 1-162-286-31 CERAMIC 220PF 10% 50VC314 1-162-282-31 CERAMIC 100PF 10% 50V
C315 1-162-282-31 CERAMIC 100PF 10% 50VC316 1-162-282-31 CERAMIC 100PF 10% 50VC317 1-162-282-31 CERAMIC 100PF 10% 50VC318 1-162-282-31 CERAMIC 100PF 10% 50VC319 1-162-282-31 CERAMIC 100PF 10% 50V
C320 1-162-306-11 CERAMIC 0.01uF 20% 16VC321 1-161-494-00 CERAMIC 0.022uF 25VC401 1-161-494-00 CERAMIC 0.022uF 25VC411 1-126-960-11 ELECT 1uF 20% 50VC416 1-126-964-11 ELECT 10uF 20% 50V
C425 1-162-282-31 CERAMIC 100PF 10% 50VC427 1-162-282-31 CERAMIC 100PF 10% 50VC462 1-161-494-00 CERAMIC 0.022uF 25VC463 1-126-964-11 ELECT 10uF 20% 50VC498 1-161-494-00 CERAMIC 0.022uF 25V
C499 1-161-494-00 CERAMIC 0.022uF 25VC500 1-164-159-11 CERAMIC 0.1uF 50VC501 1-126-937-11 ELECT 4700uF 20% 16VC513 1-126-935-11 ELECT 470uF 20% 10VC521 1-164-159-11 CERAMIC 0.1uF 50V
C522 1-126-935-11 ELECT 470uF 20% 10VC523 1-126-934-11 ELECT 220uF 20% 10VC524 1-126-934-11 ELECT 220uF 20% 10VC531 1-164-159-11 CERAMIC 0.1uF 50VC532 1-126-935-11 ELECT 470uF 20% 10V
< CONNECTOR >
* CN101 1-568-419-11 PIN, CONNECTOR 9PCN102 1-568-373-11 PIN, CONNECTOR 8PCN103 1-566-859-11 SOCKET, CONNECTOR 15P
(SYSTEM CONTROL 5 TO TC-S3)CN301 1-568-838-11 CONNECTOR, FFC 21P
* CN401 1-568-936-11 PIN, CONNECTOR 9P
< DIODE >
D105 8-719-911-19 DIODE 1SS133T-72D123 8-719-982-96 DIODE MTZJ-T-72-2.2AD501 8-719-024-99 DIODE 11ES2-NTA2BD502 8-719-024-99 DIODE 11ES2-NTA2BD503 8-719-024-99 DIODE 11ES2-NTA2B
D504 8-719-024-99 DIODE 11ES2-NTA2BD511 8-719-024-99 DIODE 11ES2-NTA2BD512 8-719-024-99 DIODE 11ES2-NTA2B
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
33
CDP-S3
R435 1-247-807-31 CARBON 100 5% 1/4WR436 1-247-807-31 CARBON 100 5% 1/4WR437 1-247-807-31 CARBON 100 5% 1/4W
R438 1-247-807-31 CARBON 100 5% 1/4WR440 1-247-807-31 CARBON 100 5% 1/4WR441 1-249-429-11 CARBON 10K 5% 1/4WR442 1-247-807-31 CARBON 100 5% 1/4WR443 1-247-807-31 CARBON 100 5% 1/4W
R444 1-247-807-31 CARBON 100 5% 1/4WR445 1-247-807-31 CARBON 100 5% 1/4WR446 1-247-807-31 CARBON 100 5% 1/4WR447 1-247-807-31 CARBON 100 5% 1/4WR448 1-247-807-31 CARBON 100 5% 1/4W
R449 1-247-807-31 CARBON 100 5% 1/4WR450 1-247-807-31 CARBON 100 5% 1/4WR451 1-247-807-31 CARBON 100 5% 1/4WR452 1-247-807-31 CARBON 100 5% 1/4WR453 1-247-807-31 CARBON 100 5% 1/4W
R456 1-249-429-11 CARBON 10K 5% 1/4WR457 1-249-429-11 CARBON 10K 5% 1/4WR459 1-247-807-31 CARBON 100 5% 1/4WR460 1-249-429-11 CARBON 10K 5% 1/4WR465 1-249-407-11 CARBON 150 5% 1/4W
R469 1-249-407-11 CARBON 150 5% 1/4WR473 1-249-407-11 CARBON 150 5% 1/4WR477 1-249-407-11 CARBON 150 5% 1/4WR480 1-249-441-11 CARBON 100K 5% 1/4WR481 1-249-407-11 CARBON 150 5% 1/4W
R482 1-249-429-11 CARBON 10K 5% 1/4WR483 1-249-429-11 CARBON 10K 5% 1/4WR484 1-247-807-31 CARBON 100 5% 1/4WR485 1-247-807-31 CARBON 100 5% 1/4WR486 1-247-807-31 CARBON 100 5% 1/4W
R487 1-247-807-31 CARBON 100 5% 1/4WR489 1-247-807-31 CARBON 100 5% 1/4WR490 1-247-807-31 CARBON 100 5% 1/4WR491 1-247-807-31 CARBON 100 5% 1/4WR492 1-249-425-11 CARBON 4.7K 5% 1/4W
R493 1-249-407-11 CARBON 150 5% 1/4WR494 1-247-807-31 CARBON 100 5% 1/4WR495 1-247-807-31 CARBON 100 5% 1/4WR496 1-249-429-11 CARBON 10K 5% 1/4WR497 1-247-807-31 CARBON 100 5% 1/4W
R500 1-249-429-11 CARBON 10K 5% 1/4W
< VIBRATOR >
X401 1-781-107-21 VIBRATOR, CERAMIC (16MHz)**************************************************************
1-678-461-11 MOTOR BOARD*************
< CAPACITOR >
C721 1-162-306-11 CERAMIC 0.01uF 30% 16V**************************************************************
1-680-995-11 PANEL (L) BOARD***************
< LED >
D701 8-719-057-97 LED SEL5923A-TP15 (X)D702 8-719-058-03 LED SEL5423E-TP15 (N)D703 8-719-057-97 LED SEL5923A-TP15 (3)D704 8-719-057-97 LED SEL5923A-TP15 (2)D705 8-719-057-97 LED SEL5923A-TP15 (1)
< RESISTOR >
R710 1-249-410-11 CARBON 270 5% 1/4WR711 1-249-411-11 CARBON 330 5% 1/4WR712 1-249-413-11 CARBON 470 5% 1/4WR713 1-249-414-11 CARBON 560 5% 1/4WR714 1-249-415-11 CARBON 680 5% 1/4W
R715 1-249-417-11 CARBON 1K 5% 1/4WR716 1-249-418-11 CARBON 1.2K 5% 1/4W
< SWITCH >
S711 1-771-410-21 SWITCH, TACTILE (m)S712 1-771-410-21 SWITCH, TACTILE (M)S713 1-771-410-21 SWITCH, TACTILE (>)S714 1-771-410-21 SWITCH, TACTILE (.)S715 1-771-410-21 SWITCH, TACTILE (x)
S716 1-771-410-21 SWITCH, TACTILE (X)S717 1-771-410-21 SWITCH, TACTILE (N)
**************************************************************
1-680-996-11 PANEL (R) BOARD***************
< RESISTOR >
R700 1-249-410-11 CARBON 270 5% 1/4WR701 1-249-411-11 CARBON 330 5% 1/4WR702 1-249-413-11 CARBON 470 5% 1/4WR703 1-249-414-11 CARBON 560 5% 1/4WR704 1-249-415-11 CARBON 680 5% 1/4W
R705 1-249-417-11 CARBON 1K 5% 1/4WR706 1-249-418-11 CARBON 1.2K 5% 1/4WR707 1-249-420-11 CARBON 1.8K 5% 1/4W
< SWITCH >
S701 1-771-410-21 SWITCH, TACTILE (DISC 3)S702 1-771-410-21 SWITCH, TACTILE (DISC 2)S703 1-771-410-21 SWITCH, TACTILE (DISC1)S704 1-771-410-21 SWITCH, TACTILE (Z (DISC 1))S705 1-771-410-21 SWITCH, TACTILE (Z (DISC 2))
S706 1-771-410-21 SWITCH, TACTILE (Z (DISC 3))S707 1-771-410-21 SWITCH, TACTILE (REPEAT)S708 1-771-410-21 SWITCH, TACTILE (PLAY MODE)
**************************************************************
1-678-457-11 TRAY SENSOR BOARD******************
< CAPACITOR >
C731 1-164-159-11 CERAMIC 0.1uF 50V
MAIN MOTOR PANEL (L) PANEL (R) TRAY SENSOR
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
34
CDP-S3
< PHOTO SENSOR >
IC731 8-749-016-76 PHOTO SENSOR RPI-321IC732 8-749-016-76 PHOTO SENSOR RPI-321IC733 8-749-016-76 PHOTO SENSOR RPI-321
< RESISTOR >
R731 1-247-876-11 CARBON 75K 5% 1/4WR732 1-249-408-11 CARBON 180 5% 1/4WR733 1-247-876-11 CARBON 75K 5% 1/4WR734 1-249-408-11 CARBON 180 5% 1/4WR735 1-247-876-11 CARBON 75K 5% 1/4W
R736 1-249-408-11 CARBON 180 5% 1/4W***********************************************************
MISCELLANEOUS**************
9 1-823-055-11 WIRE (FLAT TYPE) (21 CORE)11 1-757-633-11 CORD (WITH CONNECTOR) 17P571 X-4952-971-2 MOTOR ASSY605 1-757-710-11 WIRE (FLAT TYPE) (16 CORE)
0606 A-4735-188-A BU-30 (60) ASSY
M721 1-541-632-12 MOTOR, DC (LOADING)
The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.
TRAY SENSOR
Ver 1.1
35
CDP-S3
MEMO
CDP-S3
REVISION HISTORY
Clicking the version allows you to jump to the revised page.Also, clicking the version at the upper right on the revised page allows you to jump to the next revisedpage.
Ver. Date Description of Revision
1.0 2001.04 New
1.1 2002.09 Change of Part No. for IC731, 732, 733 on TRAY SENSOR board(ECN-CDB04887)
1.2 2002.11 Addition of Ref. No. 521, 522, 523, 524 to EXPLODED VIEWS(SPM-02098)
1.3 2002.12 Addition of Ref. No. 525 to EXPLODED VIEWS (SPM-02116)