VMC-127H - agma.com.tw
Transcript of VMC-127H - agma.com.tw
VMC-127HHIGH-SPEED & HIGH-ACCURACYVERTICAL MACHINING CENTER
1
VMC-127HVERTICAL MACHINING CENTER
Most Suitable for Needing High Speed, High Cutting Rate, High Rigidity Mold Making Industry• X & Y axes has a hardened box-way design, Z Axis with SCHNEEBERGER
roller-rail linear guide way, MRA45 rollers.• Hollow ball-screw (φ50-P16) with air cooling system for X-, Y-, and
Z- axis drive. Design with shock absorber• Rapid traverse rate 30000 mm/min, cutting feedrate 1-12000 mm/
min.• Design of C-type column with hydraulic weight-balance system
instead of using conventional chain-linked balance weight (To prevent the unexpected vibration from fast z-axis drive)
• Direct connection using a coupling for Z-axis motor.• Chip disposal system (3 screws and chip flush system
on two sides)• Design of fully support for X and Y-axes to gain
the high stability and low vibration.• Most suitable for needing high speed, high
cutting rate, high rigidity mold making industry. Without the shortcomings of high heat, high noise and high vibration when spindle speed running more than 8000rpm.
X/Y/Z : 1,200/700/600mm
(47.24"/27.56"/23.62")
24 Tools Magazine (BT-50/CAT-50)
10,000RPM Direct Driven
2
Shorten the Distance Between Work Piece and Operator • An indented foot space allows operators to get closer to the table and
workpiece.• The location of the Y-axis servomotor is at the back of the machine to shorten
the distance between the operator and table for greater work area access.
With Optional Accessories
• Safety Enhancement & Modulus Integrated Design
2 μm
Rigid Spindle Design• Heavy duty precision spindle bearings.
• A direct drive, 50-taper, 10,000RPM spindle
headstock mounts to a linear guide way Z-axis slide, enabling a rapid traverse speed of 30 meters/min (1.180in/min).
Innovative Design Enhanced By Scientific AnalysisFinite Element Analysis is used to supplement traditional machine design by strengthening areas generally overlooked by designers.
VMC-127HHIGH-RIGIDITY STRUCTURE
610mm
935mm
510mm
3
Temperature Control System for Each Ball Screw• All ball screws are air-cooled through the
center to reduce thermal growth and enable better machine accuracy.
• X and Y axis have hardened way construction.
The Z-axis uses roller-rail linear guide ways.
Superior Structure• C-Frame column with heavy duty roller-rail
guide ways on the Z-axis.
• The VMC-127H uses an hydraulically
activated nitrogen counterbalance system instead of conventional counter weights to help minimize vibration during rapid Z-axis movements.
610mm
1,400mm
1,100mm
935mm
710mm
4
VMC-127H
Calibration with Laser Interferometer is Performed and Certified by PMCAll of our machines are calibrated according to the "VDI 3441 3∂" standard. Calibration is performed for full travel length for each axis. Each measurement is taken six times to ensure the most consistent and accurate readings.
VERTICAL MACHINING CENTER
Friction Coefficient TestingAfter the exclusive "*" pattern hand scraping, technicians inspect the results using torque measurements to make sure
the ratio of contact region is over 50% and it is uniformly distributed. In addition, all contact points have a similar size, which
helps maintain even static and dynamic resistance over the entire travel range of each axis.
Ball-Bar TestingEach machine goes through telescoping ball-bar tests to check contouring accuracy and uncover any geometric errors. This testing ensures the machine structure is both square and parallel.
Hand ScrapingTo ensure consistent high quality, each slide way is hand-scraped. Each axis saddle has Turcite material on it and a special “*" design is used along with a "Z" pattern for efficient oil troughs. There is an excellent distribution of oil to all
axes, so setting time after rapid movements is eliminated, and stick-slip during cutting is minimized.
5
Linear Scales for lmproved Repeatability (Option)Linear scales on the X and Y-axes offer an exceptional positioning accuracy of up to 0.005mm over the full axes strokes. Only Heidenhain linear scales with a thermal behavior similar to that of the machine are selected so that thermal expansion can be compensated for further enhanced repeat-ability. Sealed encoders with durable aluminum housings offer improved reliability and service life.
Coolant Through Spindle (C.T.S.)(Option)Coolant through the spindle with pressure of 20-bar (150-psi) effectively reduces tool wear because of heat and the slow evacuation of metal chips.
• CTS with higher pressure is also available.
Forceful Cleaning Spray-Gun (Option)Equipped on the right front side of base, this unit along with the assistance of a high pressure coolant and air mixture helps increase table cleaning speed.
Simple Tool Length Measurement (Option)Used mostly for drilling and tapping, the Metrol system T-27R probe only measures tool length. This simple cost effective system greatly reduced tool set-up time by automatically in putting tool length values once the probe touches the tool.
6
7
Automatic Lubrication System
All AGMA machines use a pressurized central lubricating system. The PLC controlled system allows all three axes to be lubricated evenly to maintain accuracy and prolong machine life.
VERTICAL MACHINING CENTER
There Chip Auger DesignInstead of using a costly chip conveyor, the special three-chip auger system efficiently removes metal chips
produced during machining.
Electrical Cabinet All electrical components are in compliance with all safety rules and regulations.
All components inside the cabinets are clearly labeled and identified for ease of troubleshooting.
Oil Circulating Cooling System for SpindleA high efficiency spindle cooling system dissipates running induced heat generation in order to main-ainspindle accuracy and prolong spindle life.
Hinged-Belt Chip Conveyor (Option)This allows for rapid and efficient chip removal during machining in order to maintain a clean machine.
Pressurized Oil DistributorLubricating oil is evenly distributed to the sliding surfaces of the machine by using Showa brand oil distributors along with hard-plumbed, low maintenance oil lines.
24 Tools MagazineA rapid arm-type tool changer is driven with a precision cam, maintaining tool-changing accuracy of 0.01mm, which in turn will help maintain long-term spindle-clamping accuracy.
8
60
1.50"(38)
3.94
"( 1
00)
3.35
"( 8
5)
60
0
.98"
(
25)
3.35"(85)
1.38"(35)0.20 "(5)
0
.91"
( 2
3)
0.6
7"(
17)
30 45
0.28"(7)0.32"(8)
1.77""(45)
1
.49"
( 3
8)
7/24 TAPER
2.75
" (
69.
85")
M24(P=3)M24(P=3)
0
.98"
( 2
5)
1.83"(46.5)
4.01"(101.8)
0.12"(3)0.39"(10)
1.0
1"(2
5.7)
3.62
"( 9
1.85
)
3.88
"( 9
8.43
)
60
2.75
" (
69.
85")
0.39"(10)
1.83"(46.5) 0.13"(3.18)
4"(101.6)
1
.03"
( 2
6.19)
1
.38"
( 3
5.05
)
0.28"(7)0.32"(8)
1.77""(45)
3.35"(85)
1.38"(35)
0.91
"(
23)
0.6
7"(
17)
1.0
3" (
26.19
)
1
.49"
( 3
8)
0.20 "(5)
1"- 8UNC-2A
30 45
7/24 TAPER1"-8UN-2B
60
0.75"(19)
BT-50
CAT-50
9
mmin
a
70027.55
b
120047.24
c
140055.11
d
125*54.92*5
e
42.51.67
f
71027.95
ef
bc
40.94"(1040)
141.73"(3600)
76.7
7"(1
950)
129.
92"(3
300)
54.7
2"(1
390)
23.6
2"(6
00)
7.87
"(2
00)
13"(3
3)0.
47"(1
2)
124.41"(3160)138.97"(3530)
137.
79"(3
500)
121.
65"(3
090)36.81"(935)
1.8"(30)
0.7"(18)
161.81"(4110)
da
AGMA
VERTICAL MACHINING CENTER
10
Model VMC-127HSpindleSpindle Taper NO.50
Transmission Direct Type
Spindle Speed 10,000 r.p.m.
Table
Table Size 1,400mm x 710mm (55.12" x 27.95")
T-Slot Size 18mm x 6 x 125mm (0.71" x 6 x 4.92")
Work Area 1,200mm x 700mm (47.24" x 27.56")
Max. Table Load 1,200kgs (2,640 lbs)
Travel & Feedrate
X Axis 1,200mm (47.24")
Y Axis 700mm (27.56")
Z Axis 600mm (23.62")Distance from Spindle Nose to Table 200-800mm (7.84" - 31.50")
Distance from Spindle Center to Column Ways 935mm (36.81")
Rapid Traverse X, Y, Z =30,000 mm/min (1.180inch/min)
Cutting Feedrate X, Y, Z= 1~12,000mm /min
ATC
Tool Shank BT/CAT 50
Pull Stud MAS P50T-1 (45°)
Magazine Capacity 24 ToolsMax. Tool Diameter (with Adjacent Pocket Empty) ø250mm (9.84")
Max. Tool Diameter (Full Storage) ø125mm (4.92")
Max. Tool Length 300mm (11.81")
Max. Tool Weight 15kgs (33 lbs)
ATC Type Cam Driven Arm Type
Motor
Spindle (Cont./30min.) 15/18.5Kw (30min) (20/25 HP)
X/Y/Z Axes (Fanuc/Mitsubishi) 3.8Kw/3.5Kw (5.09 HP/4.69 HP)
Lubrication Pump 0.025Kw (0.033 HP)
Coolant Pump 0.49Kw (0.66 HP)
Machine Height 3,500mm (137.79")
Floor Space 4,110mm x 3,530mm (161.81"x138.98")
Machine Weight 12,000kgs (26,400 lbs)
Control Fanuc 0iMD 8.4"
•Specification is subject to change without further notice.
Standard Accessories : 1. Fanuc 0iMD 8.4"
2. Heat Exchanger for Electrical
3. Three-Color Indicator Light
4. Quartz Work Lamp
5. RS-232 Interface
6. 24 Tools Arm Type (ATC)
7. 10,000 RPM Direct Driven Spindle
8. Oil Circulating Cooling System for Spindle
9. Spindle Air Blast
10. Automatic Lubrication System
11. Fully Enclosed Splash Guard
12. Rigid Tapping
13. Automatic Power Off
14. Temperature Control System for Each Ball Screw
15. Tool Box W/Leveling Bolts & Pads
16. Operation Manual & Maintenance Manual
17. X+Y Axis Screw Type Chip Auger (3 pcs)
18. Transformer (Exclude India, USA and Canada)
19. CE/CSA Electrical System (For European/Canada Country Only)
Optional Accessories : 1. Fanuc 31iMB Controller
2. 32 Tools Arm Type (ATC)
3. 12,000 RPM Direct Driven Spindle
4. Chip Conveyor
5. Coolant Through Tool
6. Heidenhain Optical Linear Scales for all axes
7. Coolant Through Spindle (20/70 Bars-Closed Hole) A Type
8. Automatic Tool Length Measurement System
9. Rotary Table (4th Axis)
10. Electrical Box Air Conditioner Device
VERTICAL MACHINING CENTER
13
04
12
02
T
EL
: 04
-24
73
33
26
Distributor :AGMACHINE TECHNO CO., LTD.No.7, Ln. 34, Jhuangcian Rd., Shengang Dist . ,
Taichung City 42951, Taiwan(R.O.C.)
TEL:+886-4-25612868
FAX:+886-4-25610409 & 25613010
E-mail : [email protected]
http://www.agma.com.tw