1

USER’S MANUALActive sound set

PAS-300

SUB-1000

PAS-300PAS-350

2

PAS-300

RIGHT LEFT

SUB250WattSAT2x75Watt

SAT OUT

LINK OUT

INPUT

PEAK PEAK PEAK

SUBLEVEL LEFTRIGHT

~100-240V T2.5A

PAIRSTATUS

INPUT1+ = positive1- = negative

2+ = no connection2- = no connection

4Ω75Watt rms

SATELITE PAS-300

1

9

10

11

12

Tripod

PAS-300Subwoofer

Control Panel

GB

2

3

4

5

6

7

8

13

SatelleteConnection Panel

3

APPLICATIONThe PAS-300 is a sound system with 1 subwoofer and 2 satellite speakers.The PAS-300 is powered through a mixing panel or master output from another amplifier or audio source. The subwoofer contains three separate speakers. 1 for the subwoofer and 2 (left and right) for the satellite speakers. The satellite speakers may be placed onto the supplied tripods. The satellite speakers are connected to the subwoofer using the speaker cable with Speakon plugs. The subwoofer is provided with a volume control for each speaker. These must be set before use. The ultimate volume is controlled on the external audio source.

FUNCTIONS

SUBWOOFER1. Bluetooth® function (optional).2. Volume controls. 2 x for satellite speakers and 1 x for subwoofer.3. Audio input, left and right (symmetrical), XLR or jack 6.3mm.4. Audio input, left and right (asymmetrical), Cinch.5. Audio output, left and right (asymmetrical), XLR (the same signal as input).6. Satellite speaker output, left and right, Speakon (cables included).7. 230V mains lead input (included) with fuse holder T2,5A.8. Power switch.

TRIPOD9. height tube10. Retainer11. height tube lock nut12. tripod feet lock nut SATELLITE SPEAKER13. Speakon speaker input (connect with speaker output (6)).

4

WARNING/MAINTENANCE

GENERAL:• Carefully read the user’s manual and follow all directions.• Before cleaning the speaker, always remove the mains cable from the wall

socket and switch off the speaker.• Clean the cabinet with a slightly moist cloth.• Never place or use the set in wet or humid space or environment.• Ensure adequate heat dissipation; never cover the set nor place it directly next

to a heat source.• Prevent damaging the mains cable and ensure it doesn’t cause a risk of tripping

or falling.• Never disassemble the set; this may only be performed by qualified personnel.• Only turn on the speaker after setting all volume controls to MINIMUM (0), to

avoid possible scares when switching on.• Prolonged listening to high volume levels can cause hearing damage

BEFORE USE

The PAS-300 functions on the mains.The PAS-300 satellites function on the built-in speakers in the subwoofer and must be connected using the supplied speaker cables with Speakon plugs.

MAINS VOLTAGE:Only connect the PAS-300 subwoofer to a mains voltage of 230 Volt. The mains in most European countries works on 230 Volt.

Use the supplied power cord to connect the PAS-300 with the mains.

AMPLIFIER SETTINGSPOWER SWITCH:Use the power switch to switch on the amplifier.

INPUT:Connect an external audio source to the input of the PAS-300.The connection can be made with XLR, Jack 6.3mm of cinch plugs.

LEFT/RIGHT VOLUME CONTROL (SATELLITE):Use the LEFT and RIGHT volume controls to adjust the volume of the satellites.When the volume reaches the maximum level, the related peak LED will illuminate.

5

SUB LEVEL VOLUME CONTROL:Use the SUB LEVEL volume control to adjust the volume of the subwoofer (low pitch). When the volume reaches the maximum level, the related peak LED will illuminate.

ADJUSTING:Use the volume buttons to set the correct volume balance between left, right and subwoofer. This may differ per setup.

LINK OUT: These audio outputs receive the same signal as provided through the input. The signal may then be linked to a second set or another amplifier.

BLUETOOTH ® (optional):To be able to use the wireless Bluetooth® function, the PAS-300 must be paired with the external Bluetooth® device that contains the music (mobile phone, tablet or other). Pair the devices as follows:1. Switch on the PAS-300 and enable the Bluetooth® function by pressing and

holding the “PAIR” button for at least 3 seconds until the status LED starts flashing.

2. Enable the search function of the Bluetooth® device that contains the music; refer to the user manual of that device.

3. Now select “ALECTO” in the list that appears in the display of the Bluetooth® that contains the music.

4. The status LED of the Bluetooth® function will now remain lit.5. If asked for a password, please enter the PIN code “0000” on the Bluetooth®

device (when the connection is interrupted, the status LED will start flashing again).

6. Depending on the type of device that contains the music, you might have to set this device to send its audio signal to the PAS-300 and not to the headphones output or its own speaker; please refer to the user instructions of the external device.

7. Attention: the PAS-300 only plays music; it does not support phone calls.8. After use, please press and hold the “PAIR” button for at least 3 seconds to

switch off the Bluetooth® device. The status LED will now switch off.

ENVIRONMENT• The packaging of this baby video monitor can be discarded as waste

paper. However, we advise you to save this packaging so you can adequately protect the devices for transportation.

• In case the baby video monitor is being replaced, please return it to your supplier; they will guarantee environment-friendly processing.

6

TECHNICAL SPECIFICATIONSPAS-300:Voltage: 230V~50HzFuse: T 2,5A 230VWoofer: 10”Satellite: 4” Mediant x 2 and 1” Neodymium TweeterImpedance Satellite: 4ΩSystem Freq. Resp.: 45Hz~20KHz +/-3dBSubwoofer Freq. Resp.: 45Hz~140Hz +/-3dBSatellite Freq. Resp.: 140Hz~20KHz +/-3dBSystem Power: 380 Watts RMSSubwoofer Power: 250 Watts RMSSatellite Power: 2 x 65Watts RMS – impedanite minimal 4ΩSatellite Dimensions(WxDxH): 150*160*410mmNet Weight: 4.5KgSubwoofer Dimensions(WxDxH): 410*330*415mmNet Weight: 15KgThe amplifier with Bluetooth® (optioneel)With Overcurrent, Short Circuit, Overload and Overheat Protections

Warning: Using the speaker for long periods of time on high volumes can lead to permanent ear damage. To protect your hearing, please keep in mind the following:

• Increase the volume starting at the minimum up to a comfortable level.• Do not listen for long periods of time on high volumes.• Never increase the volume to outdo or ignore environmental noise.• Decrease the volume when you cannot hear the people around you.

7

CONNECTION DETAILSBALANCED/UNBALANCED

Stereo headphones:

Tip is left signal

Ring is right signal

Sleeve is mass,earth or shielding

TipRing

Sleeve

unbalanced mono:

Tip is signal

Sleeve is mass,earth or shielding

Tip

Sleeve

balanced mono:

Tip is signal +

Ring is signal -

Sleeve is mass,earth or shielding

TipRing

SleevePull relief Pull relief Pull relief

PUSH Balanced XLR connectior:PIN 1 is mass, earth or shielding

PIN 2 is signal +PIN 3 is signal -

To 1 side, connect PIN 1 with PIN 3 for unbalanced XLR connection.

Balanced XLR cable:PIN 1 is mass, earth or shielding

PIN 2 is signal +PIN 3 is signal -

To 1 side, connect PIN 1 with PIN 3 for unbalanced XLR cable.

2+

1+1-

2-2+ 2-

1- 1+

V1.0

Service

Help

Service Help

WWW.ALECTO.NLSERVICE@ALECTO.NL

NL 073 6411 355 (Lokaal tarief)

BE 03 238 5666 (Lokaal tarief) (Tarif local)

DE 0180 503 0085 Lokale Festnetzkosten

Hesdo, Australiëlaan 15232 BB, ‘s-HertogenboschThe Netherlands

WWW.ALECTO.NLSERVICE@ALECTO.NL

NL 073 6411 355

BE 03 238 5666

DE 0180 503 0085

Hesdo, Australiëlaan 1, 5232 BB,‘s-Hertogenbosch, The Netherlands

(Lokaal tarief)(Tarif local)

(Lokaal tarief)

(Lokale Festnetzkosten)

v2.1