SERVICE MANUAL Colour Television Model No....

SERVICE MANUAL Colour Television

SpecificationsPower Source . . . . . . . . . AC220-240V, 50Hz/60Hz.Colour System . . . . . . . . PAL (AV Input: PAL/NTSC4.43/NTSC/PAL-60Hz)Television System . . . . . . B/GChannel Coverage . . . . . VHF: E2-E12

UHF: 21-69CATV: S1-S41, X, Y, Z, Z+1, Z+2

Video IF . . . . . . . . . . . . . . 38.0MHz Aerial Input Impedance . . 75ΩExt. Terminals

Video inputs: Phono jack x 2 (1Vp - p, 75Ω)S-Video inputs: Din 4 pin x 1 (Separate Y/C signal input)Audio inputs: Phono jack (L/R) x 2 (436mVrms, more than 40KΩ)Video monitor outputs: Phono jack x 1 (1Vp - p, 75Ω)Audio monitor outputs: Phono jack (L/R) x 1 (436mVrms, less than 600Ω)Headphone jack: Mini stereo jack x 1

Speaker . . . . . . . . . . . . . . 5 cm x 12 cm x 2 pcs.Sound Output (RMS) . . . . 5W + 5WDimensions . . . . . . . . . . . 587.5 (W) x 596.5 (H) x 488.5 (D)mmWeight . . . . . . . . . . . . . . . approx. 21.3 Kg

Specifications subject to change without notice.

Product Code: 111351417

Original Version

Chassis Series: FC3-A

C2GW

FILE NO.

Model No. CP21AF2X

Service Ref. No. CP21AF2X-00

(Australia)

Give complete “SERVICE REF. NO.” forparts order or servicing. It is shown on therating plate at the cabinet back of the unit.

This T.V. receiver will not work properly in foreign countries where the televisiontransmission system and power source dif-fer from the design specifications. Refer tothe specification table.

0

7

1 4

85

2 3

6

9

P

P

JXMYA

-/--

P P

TV/AV

A B

CH SCAN

TIMER

MENU PIC MODE

SWAP

BASS SURROUND

REFERENCE NO. SM5110420

- + PMENUTV/AV

Contents

-2-

Safety Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Chassis Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4IC Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8Mechanical Disassemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Service Adjustments with replacing Memory IC (IC802) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-13Service Mode Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-15Service Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Special Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17Purity and Convergence Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Cabinet Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Chassis Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-28

Safety Notice

SAFETY PRECAUTIONS

1: An isolation transformer should be connected in thepower line between the receiver and the AC linewhen a service is performed on the primary of theconverter transformer of the set.

2: Comply with all caution and safety-related notes pro-vided on the cabinet back, inside the cabinet, on thechassis or the picture tube.

3: When replacing a chassis in the cabinet, always becertain that all the protective devices are installedproperly, such as, control knobs, adjustment coversor shields, barriers, isolation resistor-capacitor net-works etc.. Before returning any television to thecustomer, the service technician must be sure thatit is completely safe to operate without danger ofelectrical shock.

X-RADIATION PRECAUTION

The primary source of X-RADIATION in television receiver is the picture tube. The picture tube is specially con-structed to limit X-RADIATION emissions. For continued X-RADIATION protection, the replacement tube must bethe same type as the original including suffix letter. Excessive high voltage may produce potentially hazardous X- RADIATION. To avoid such hazards, the high voltage must be maintained within specified limit. Refer to this ser-vice manual, high voltage adjustment for specific high voltage limit. If high voltage exceeds specified limits, takenecessary corrective action. Carefully follow the instructions for + B1 volt power supply adjustment, and high volt-age check to maintain the high voltage within the specified limits.

PRODUCT SAFETY NOTICE

Product safety should be considered when a component replacement is made in any area of a receiver.Components indicated by mark in the parts list and the schematic diagram designate components in whichsafety can be of special significance. It is particularly recommended that only parts designated on the parts listin this manual be used for component replacement designated by mark . No deviations from resistancewattage or voltage ratings may be made for replacement items designated by mark .

-3-

Chassis Block Diagrams

130V

24V

28V

13V

9V 9V 5V

36V

FB

TT

UN

ER

HO

RIZ

. DE

F.V

ER

T. D

EF.

MA

IN S

OU

ND

AM

P.

SU

RR

OU

ND

. AV

SW

AU

DIO

CT

L / 1

CH

IP IC

CP

U /

EE

PR

OM

PO

WE

R S

UP

PLY

CIR

CU

IT

A10

1T

UN

ER

SA

W

FIL

TE

R

X16

1A

IF IN

5/6IC

201

IF/V

IDE

O/C

HR

OM

A

VID

EO

/(S

-Y)

IN19 20 21

R-O

UT

B-O

UT

G-O

UT

IC28

1S

EC

AM

6 7

R-Y

OU

T

B-Y

OU

T

35 34

IC50

1V

ER

T. /D

EF.

23 27

VE

RT.

OU

T

HO

RIZ

. OU

T

15

IC80

1C

PU

T47

1F

BT

HE

ATE

R

PC

C

CIR

CU

ITQ

461-

Q46

2

Q43

1H

-DR

IVE

Q43

2H

-OU

T

HV

L902

DY

CR

T U

NIT

CR

T

T43

1H

-DR

IVE

TR

AN

S.

HV

FO

CU

S

SC

RE

EN

IC70

1T

RIP

LE

VID

EO

O

UT

PU

T A

MP.

R BG

1 2 3

9 8 7

R BG

D19

10LE

DA

1901

AR

C R

EC

EIV

ER

FR

ON

T

CO

NT

RO

L K

EY

SS

W19

01~

SW

1906

IC80

2E

EP

RO

M43

65SDA

SCL

3212

28

ON-TIMER

RC-IN

KEY-IN

REAR AV1 INPUT TERMINAL F

RO

NT

AV

2 IN

PU

T T

ER

MIN

AL

VID

EO

MO

NIT

OR

OU

T

AU

DIO

MO

NIT

OR

OU

T(L

EF

T)

AU

DIO

MO

NIT

OR

OU

T(R

IGH

T)

46 44

VID

EO

OU

T

S-C

IN

42

AV

1

AV

2

VID

EO

IN

AU

DIO

IN (

LEF

T)

AU

DIO

IN (

RIG

HT

)

VID

EO

IN

AU

DIO

IN (

LEF

T)

AU

DIO

IN (

RIG

HT

)

SP

901

SP

902

IC00

1 A

UD

IO A

MP.

7 12

4 2

IC37

01

AU

DIO

CO

NT

RO

L /

SU

RR

OU

ND

23 8

R L

2F

M O

UT

(TV

OU

T)

2/5

1/3

L/R

, L/L

,R/R

SW

151 30

4

L RL-

OU

T

R-O

UT

IC37

02

52 54

SIF

OU

T

SIF

IN

K00

1H

EA

DP

HO

NE

JA

CK

IC12

01A

UD

IO-S

W

11

13

152

3

4

1/5

L-O

UT

R-O

UT

IC15

01V

IDE

O S

WIC

1401

VID

EO

-SW

9 6

4

172

15

1 13 12

14

54

3

INT. VIDEO EXT. VIDEO

VID

EO

M

ON

ITO

RO

UT

Y

EX

T.

VID

EO

AV

1 V

IDE

O IN Y-IN

C-I

N AV2 VIDEO IN

12/1

4A

V1

AV

2

S-T

ER

MIN

AL

Y-IN

C-I

N

14

VID

EO

IN

1H DLRGB

MATRIX

1920

21

OSD R-OUT

OSD B-OUT

OSD G-OUT

OS

D R

-IN

OS

D B

-IN

OS

D G

-IN

14 15 16

MAIN SIGNAL PROCESSING CIRCUIT

(Not

equ

ippe

d)

* N

ot e

quip

ped

-4-

Chassis Block DiagramsSYSTEM CONTROL

12K

EY

SW

ITC

H IN

KE

YS

WIT

CH

TV

/AV

SW

ITC

H

(TV

=LO

W,

AV

=H

IGH

)

SC

L2 1 31

SD

A

PO

WE

R O

N/O

FF

PH

OT

O C

OU

PLE

(O

N=

HIG

H, O

FF

=LO

W)

IC20

1IF

/VID

EO

/ C

HR

OM

A/D

EF

.

IC80

1C

PU

QX

XA

VC

044P

22 19 20 21 18 17 273

476322823 33

OS

D B

LK O

UT

(Act

ive=

Hig

h)

OS

D R

ED

OU

T(A

ctiv

e=H

igh)

OS

D G

RE

EN

OU

T(A

ctiv

e=H

igh)

OS

D B

LUE

OU

T(A

ctiv

e=H

igh)

DE

FLE

CT

ION

CIR

CU

IT

HO

RIZ

. SY

NC

IN (

AC

TIV

E=

LOW

)

VE

RT

. SY

NC

IN (

AC

TIV

E=

LOW

)

PO

WE

R P

RO

TE

CT

IN

(P

OW

ER

ER

RO

R=

LOW

)P

OW

ER

CIR

CU

ITet

c.

SCL

SDA

IC80

2M

EM

OR

Y

OS

CX

801

32.7

68K

Hz

CP

U O

SC

OU

T

CP

U O

SC

IN

LED

ON

-TIM

ER

LE

D O

UT

(ON

TIM

ER

ON

=Lo

w)

RC

SIG

NA

L IN

(AC

TIV

E=

HIG

H)

RC

PR

E-A

MP

.

24 26

IC00

1A

UD

IO A

MP

.

VIF

-M O

UT

PU

T (

HIG

H=

NT

SC

3.58

, LO

W=

OT

HE

R)

A10

1F

/S T

UN

ER

AF

T S

IGN

AL

INP

UT

10

RE

SE

T IN

PU

T (

AC

TIV

E=

LOW

)13

MU

TE

OU

TP

UT

(MU

TE

ON

=H

IGH

)29

AV

1/A

V2

SW

ITC

H(A

V1=

LOW

, AV

2=H

IGH

)

IC12

01A

UD

IO S

WIT

CH

56

SE

CA

M K

ILLE

R IN

PU

T (

HIG

H=

SE

CA

M)

IC37

01A

UD

IO C

ON

TR

OL

&S

UR

RO

UN

D13

14

11 10

IC14

01V

IDE

O S

WIT

CH

8

1112

IC37

02L/

R, L

/L, R

/R

SW

ITC

H9

1710

18

9

IC15

01V

IDE

O S

WIT

CH

113

(AV

1=LO

W,

AV

2=H

IGH

)

(Y =

LOW

, A

V V

IDE

O=

HIG

H)

(Y =

LOW

, A

V V

IDE

O=

HIG

H)

10

(IN

T. V

IDE

O =

LOW

, E

XT

. VID

EO

=H

IGH

)

-5-

IC Block DiagramsIC201 < IF/Video/Chroma/Def. > LA76818

1

DC

VO

L

SW F

MD

ET

23

45

6

IFA

GC

RF

AG

C

VIF

78

910

IFV

CC

5V11

1213

BU

S

PE

AK

ING

CO

RIN

GB

LAC

KS

TR

ET

CH

SY

NC

SE

P

1415

AB

L

DC

RE

ST

CLA

MP

OS

DC

ON

TR

AS

TB

RIG

HT

1617

1819

20

CO

NT

RA

ST

BR

IGH

TR

GB

MAT

RIX

OS

DS

W

DR

IVE

/OU

T-OF

F

VC

C21

2223

FS

C/

SY

NC

SW

2425

2627

VE

RR

AM

PH

OR

VC

CHV

CC

VE

RC

/D

HO

RO

UT

PH

AS

ES

HIF

TE

R

AF

C2

AF

C1

VE

RS

EP

HO

RC

/D

1/256

CO

LOR

CLA

MP

LPF

ALC

+S

WC

LAM

P

DE

MO

PAL

SW

AC

C

BP

FO

N/O

FF

DE

LAYLIN

E

SW

TR

AP

AF

TV

IDE

OD

ET

TR

AP

LIMA

MP

BP

F

SP

LL

BP

F

VID

EO

AM

P

IFID

EN

TV

IDE

O

SW

AP

C1

TIN

T

VX

OD

DS

AP

C2

DC

AD

S.

CLA

MP

VC

O

1H D

ELAY

HO

RV

CO

FB

P

2829

3031

321H

VC

C

3334

3536

3738

3940

4142

CLM

P

4344

45

CLM

P

V/C

VC

C5V

4647

4849

50

A2C

PLL

5152

5354Audio Output

FM Output/Selected Audio Output

PIF AGC

RF AGC Output

PIF Input1

PIF Input 2

IF Ground

IF Vcc

FM Filter

AFT Output

Bus Data

Bus Clock

ABL

Red Input

Green Input

Blue Input

Fast Blanking Input

RGB Vcc

Red Output

Green Output

Blue Output

fsc output or CSync output

Vertical Output

Ramp ALC Filter

Horizontal/BUS Vcc

Horizontal Output

Horizontal AFC Filter

Flyback Pulse Input

VCO IREF

Clock (4MHz) Outupt

CCD Vcc

CCD Filter

CCD/Horizontal Ground

SECAM B-Y Input (Cb Input)

SECAM R-Y Input (Cr Input)

Chroma APC2 Filter

Clamp Filter

4.43 MHz Crystal

Chroma APC1 Filter

Selected Video Output

Video/Vertical/BUS Ground

External Video Input(Y-IN)

Video/Vertical Vcc

Internal Video Input (S-C IN)

Black Level Detector

Video Output

VCO Filter

VCO Coil 2

VCO Coil 1

APC Filter

Ext. Audio Input

SIF Output

SIF APC Filter

SIF Input

IC Block Diagrams

-6-

IC201 <IF System Block Diagram> LA76818

1112

BU

SIn

terf

ace

SA

W

5 6 4 8 7

PIF

In1

PIF

In2

IF In

9V

30K

RF

AG

CO

ut

120K

IF V

CC

IFG

ND

VIF

AM

P

VIF

1V

IF 2

VIF

3

IF A

GC

D

rive

RF

AG

C2n

dIF

AG

C

RF

AG

CD

elay

6bit

IF A

GC

Def

1bit

+ - (6 V

cc)/

7

To BU

S

3

0.02

2uP

IFA

GCIF

AG

C

Dat

aC

lock

AP

CD

et

+π/

4

-π/4

Snd Det

Am

p

52S

IF.O

ut

Sou

ndTr

ap

Vid

eoD

et

Buz

zC

ance

ller

50A

PC

Filt

er33

00.

47u

+

PLL

Pul

l-in

SW

To BU

S

Lock

Det

Vid

eo.L

evel

3b

it

Am

p54

10p

SIF

.In

Sou

ndB

PF

VC

O.C

oil

VC

OC

OIL

1V

CO

CO

IL2

4849

VIF

VC

OC

hrom

aC

ount

er

B/N

INV

IFId

ent

OS

CC

/D

Am

p

SIF

. Sys

2bit

pre-

scal

ler

SIF

VC

O

500K

BP

FSIF

AP

CF

ilter

1K

0.01

u10

00p

53LI

MA

MP

FM

Det

FM

.Lev

el5b

it

Chr

oma

C/D

AP

CD

et

500K

Det

To BU

S

Chr

oma

VC

O VIF

Cou

nter

Res

etP

ulse

VC

OId

ent

VIF

.Sys

2bit

Pha

seD

etec

tor

A.M

UT

E1b

itV

OLU

ME

D/A

VO

LUM

EF

ilter

A.S

W1b

itInpu

tS

elec

tV

OLU

ME

(AT

T)

-+

-+

2.5V

Am

p

FM

Gai

n1b

itD

eem

-TC

1bit

De-

emph

FM

Mut

e1

bit

2 9 46 51 1

A.F

il.D

ef1b

it

VO

LUM

E7b

it

47

VC

OA

lignm

ent

AF

T10

AF

T

Vcc 100K 100K

0.1u

VC

OF

ilter

+

0.47uAud

io.o

ut

+Aud

io in

10u

Vid

eo

Out

FM

Filt

er+

1u

FM

Out

0.01u

+

to B

US

Lin

e

+

-7-

IC Block Diagrams

ThermalProtection

-

+AMP

PumpUp

1

INV

ER

TIN

G

INP

UT

2

Vcc

3

PU

MP

UP

OU

T

4

GN

D

5

Ver

. OU

TP

UT

6

OU

TP

UT

S

TAG

E V

cc

7

NO

N IN

V.IN

PU

T

IC001 < Audio AMP.> TA8200AH

4

5

3

1

2

6 9

7

10

12

118

+Ripple Filter

AMP.1

IN 1 +

+

+

+

++

IN 1

Pre-GND

400Ω

400Ω 20KΩ

20KΩ

+AMP.2IN 2 IN 2+

Vcc

Vcc

OUT 1

PW-GND

OUT 2

+

+

RL

RL

1

IN 32

Vcc

3

SW14

OUT

5

GND

6

IN1-Y7

IN1-C

8

SW2

9

IN 2

SW

6dB

(-6dB)

CLAMP

CLAMPCLAMP

BIA

S

6dB

SW

15K

SW1 SW2 OUTLH-

L IN 1LH

IN 2IN 3

IC1401 < VIDEO Switch > MM1188XS

IC501 < Vertical Output > LA78040N

IC Block Diagrams

-8-

VDD VDD VDD

VDD

MIRROR 2

VDD

FLASH-DIODE

1xVOC

InvertingInput

(3x)

1,2,3

9,8,7

3x

VDD

6

5

4

Non-invertingInput

Vip

MIRROR 1

Vbias

MIRROR 3

LEVEL-SHIFTER 1

LEVEL-SHIFTER 2

DIFFERENTIALSTAGE

CURRENTSOURCES

GND

THERMALPROTECTION

Note: One amplifier shown.

CathodeOutput

(3x)

Vi

IC701 < Triple Video Output Amplifier. > TDA6103Q

IC3701 < Audio Control & Surround > NJW1138MP

10 7

1

69 8

20

22

54

NJRCORIGINAL

SURROUND &

SIMULATED SURROUND

IIC BUSINTERFACE

AGC

BIAS

TONEVOL 1

TONE

27

VOL 1

VOL 2

VOL 2

19

18

17

14

13

16

15

21

30

23242526

12

11

IN 1a

AGC SS-FIL OUT 1a IN 2aTONE

Ha TONELa

OUT 2a

CVA

CVB

CTH

CTL

AUX0

AUX1

SCL

SDA

V+

GND

VREFOUT 2bSR-FIL OUT 1b IN 2b TONEHb

TONELb

IN 1b

Service Information

-9-

This TV set has a built-in power supply protection circuit.It is provided to protect the TV set in case of a power supply circuit malfunctions. When something abnormality occursduring TV reception, the TV set goes to the stand-by mode.

When an abnormality occurs during TV reception, it causes pin 27 of the CPU to go continually Low (less than0.75V) for about one second. The CPU detects that this has occurred and outputs the signal from pin 31 to switchoff the power supply lines.

Releasing the protective circuit and restoring power supply

To release the protective circuit and restore power supply, turn the power to the TV set OFF and then ON again viaeither the main power switch or the ON-OFF button on the remote control. This will work only if the power supplytrouble was temporary. If there is permanent trouble such as a damaged circuit, power cannot be restored and thecircuit will have to be repaired.

Protection Circuit

L

R

AUDIO

AV1 INPUT

VIDEO

(MONO)

S-VIDEO

MONITOROUT

ANT. 75Ω

Mechanical DisassembliesCABINET BACK REMOVAL1. Refer to Figure 1, remove 8 screws.2. Pull off cabinet back and remove.

Figure 1. Cabinet Back Removal

CHASSIS REMOVAL1. Remove cabinet back.2. Discharge the picture tube anode (2nd anode lead) to the dag

coating (picture tube grounding lead).3. Disconnect Degaussing coil socket (KE), Picture tube socket,

Deflection yoke connector (KDY), Speaker connectors (K002and K003), and 2nd anode lead.

4. Remove chassis completely by sliding it straight back.

PICTURE TUBE REMOVALCAUTION: Do not disturb the deflection yoke or magnet

assembly on the picture tube neck. Care must be takento keep these assemblies intact, unless picture tube isbeing replaced . Discharge the picture tube to the coat-ing before handling the tube.

1. Remove chassis, referring to Chassis Removal instructions.2. Place cabinet’s front face down on the soft surface.3. Remove the screw on each corner of the picture tube and

GENTLY lift the picture tube out of the cabinet.4. Install a replacement picture tube in reverse order.

Properly install the degaussing coil and picture tube grounding lead on the picture tube. See Figure 2.

Note: If the Picture Tube is being replaced, mount theDegaussing Coil on the picture tube. See Figure 2.

DEGAUSSINGCOIL DEGAUSSING

COIL HOLDER

DEGAUSSINGCOIL SOCKET

To CRT unit ground

PICTURE TUBEGROUND LEAD

Figure 2.Picture Tube Removal

[1] Initializing Procedure1. Put a new memory IC.2. Turn on the TV set.3. Press and hold the TV/AV Selector on the TV set for more than 2 seconds. The following picture appears on the

screen.

4. Press the PROGRAMME UP on the TV set while the above On-Screen Display is still on the screen. The followingpicture appears on the screen.

This completes the initialization of memory IC.

Following shows the initialized contents of memory data by this procedure.- Plug & play : No executed- Inhibit data : Cancelled- Ch skip data : Cancelled- Sound volume data : 10/63 steps.- Volume Lock : OFF- Tuning Lock : OFF- Colour system : AUTO

1

CLR

- + PMENUTV/AV

-10-

Service Adjustments with Replacing Memory IC (IC802)

Note: The CPU (IC801) and memory IC (IC802) store the service adjustments data and controls data for each circuit. When the Memory IC(IC802) is replaced, some of the service adjustments should be readjusted to obtain the best performance. The necessary service adjustments are carried out by using the RC handset.Please set up the TV set with following steps [1] to [2].

Press and hold for more than 2 seconds

- + PMENUTV/AV

-11-

Service Adjustments with Replacing Memory IC(IC802)[2] Required Service AdjustmentsReadjust the following service adjustments.Adjustments Service Mode No. & ItemRF AGC Item 01, RF AGCHorizontal centre Item 02, H-PHAVertical size Item 04, V-SIZVertical-S correction Item 05, V-SCOVertical linearity Item 06, V-LINGray scale Item 14-17, 19-21

Further adjustment please refer to page 14 and 15.

Following table shows the initial values which have been stored in the CPU ROM, and items for the service adjustments.Service mode adjustments table in CPU ROM

NO. ITEM DATARANGE

INITIALDATA DESCRIPTION

0102030405060708091011121314151617181920

RF AGC Adj.RF AGC 00~63 21H-Phase (H-Centering) Adj. (50Hz)H-PHA 00~31 9V-Position (V-Centering) Adj. (50Hz) Fixed.V-POS 00~63 40V-Size Adj. (50Hz)V-SIZ 00~127 47V-S Correction (50Hz). Strech or shrink at center of screenV-SCO 00~31 13V-Linearity Adj. (50Hz)V-LIN 00~31 18H-Centering Adj. (60Hz) H-P60 -16~+15 +4V-Size Adj. (60Hz) V-S60 -64~+32 -1OSD H-Position Adj.OSDHP 00~255 26OSD Contrast Adj.OSDC 00~127 40Correction of the V-size accompanying brightness change. V-SCP 00~07 7Correction of the H-size accompanying brightness change.H-SCP 00~07 7Sub Bias Adj.SBIAS 00~127 105Red Bias Adj.RBIAS 00~255 0Green Bias Adj.GBIAS 00~255 0Blue Bias Adj.BBIAS 00~255 0Red Drive Adj.RDRIV 00~127 64Green Drive Adj.GDRIV 00~15 8Blue Drive Adj.BDRIV 00~127 64

1-LINE APPEAR

21 DRV White Balance Adj.22 B-YD 00~15 9 B-Y DC level Adj.. Colour compensation (PAL)23 R-YD 00~15 9 R-Y DC level Adj.. Colour compensation (PAL)24 B-YDN -16~+15 0 NTSC B-Y DC level Adj. (Difference value from PAL.)

25 R-YDN -16~+15 0 NTSC R-Y DC level Adj. (Difference value from PAL.)26 SBDC -16~+15 - 8 SECAM B-Y DC level Adj. (Difference value from PAL.)27 SRDC -16~+15 - 5 SECAM R-Y DC level Adj. (Difference value from PAL.)28 G-YA 0,1 0 G-Y angle Adj. (Colour Phase G-Y Demodulation 0=240 degree, 1=253 degree)29 RBGB 00~15 8 R-Y, B-Y Gain Blance Adj. (Do not change.)30 RBAG 00~15 8 R-Y, B-Y Angle Adj. (Do not change.) 31 G-YAN 0,1 0 NTSC G-Y Angle Adj. (Difference value from PAL.)32 RBGBN -16~+15 0 NTSC R-Y, B-Y Gain Balance Adj. (Difference value from PAL.)33 RBAGN -16~+15 0 NTSC G-Y, B-Y Angle Adj. (Difference value from PAL) 34 COGV 00~03 0 Coring Adj. (Base colour)35 BLKS 00~03 3 Black stretch effective point selection, 0=OFF, 1-3=FREE36 BLKG 00~03 3 Setting of Black stretch gain. 0=OFF, 1-3=FREE37 BRTA 0,1 0 On and off of ABL. 0=ON, 1=OFF38 BRST 0,1 0 ABL Effect Limit SW. 0=With Limitter, 1=Without Limitter

39 BRTH 00~07 0 ABL Threshold Pint.

(Do not change)

4041424344

White peak limitter. 0=OFF, 1-3=With LimitterWPL 00~03 2Y Gamma setting. 0=OFF, 3=Max (Do not change)YGAM 00~03 0Switching of Pre-shoot and Over shoot in AV mode. 0=Pre, 1=OverPORW 0,1 0Pre-shoot/Over shoot Adj. in AV mode.PORS 00~03 2

RF Coring Gain Adj.RFCO 00~03 0

OBJECT

IC201IC201IC201IC201IC201IC201IC201IC201

IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201

IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201

IC801

-12-

Service Adjustments with Replacing Memory IC (IC802)

NO. ITEM DATARANGE

INITIALDATA DESCRIPTION

454647484950515253545556575859

Switching of RF Pre-shoot and Over shoot. 0=Pre, 1=Over PORWN 0,1 0RF Pre-shoot/Over shoot Gain Adj. PORSN 00~03 0RF Tint Adj.TINT -16~+15 0

NTSC 4.43 Tint Adj.TINT 443 -16~+15 -12RF Sharpness Adj.SHRF -32~+31 0

OSD TEXT Contrast.TEXTC -128~+127 0Volume Control Adj.VOLUM 00~255 127De emphasis TC. 0=50µs (PAL), 1=75µs (NTSC)DEEM 00~01 0VIF System Switch. 00=38MH, 01=38.9MH, 02=45.75MH, 03=58.75MHVIFSW 00~03 0SIF System Switch.SIFSW 00~03 1

Video Level Adj. (36-pin Detect Out) (Fixed)V-LVL 00~07 4FM Level Adj.FMLVL 00~31 16Over Modulation Switch. 0=OFF, 1=ON (With Limitter)IFOM-S 0,1 0

FM Out or Monitor Out Switch. 2-pin Out, 0=FM OUT, 1=MONITOR OUTIFMN-S 0,1 0

IFTRPS

60 IFMLVL Modulation Level61

H-FRQ 00~63 34 Correction of Horizontal Frequency. (Fixed)62

FBTS 0,1 0 Switching of H-blanking and Flyback Pulse. 0=INT. H-BLK,1=INT. & EXT.H-BLK63

COOP 00~07 2 Setting of Colour Killer Level. 0= -30db, 7= -40db64HBLKL 00~07 7 H-Blanking Control. (Left)65HBLKR 00~07 3 H-Blanking Control. (Right)66AFCRF 0,1 0 RF AFC Gain & Gate Adj. 0=AUTO, 1=COMPULSION67VSURF 0,1 0 RF V-Sync. Separation Sensibirity. 0=NORMAL, 1=HIGH68

CDMRF 00~07 0 RF V-Countdown Circuit Adj. 50/60Hz Jage, Sync. Trigger 0=AUTO, 1=Ext. Trigger 69AFCAV 0,1 0 AV AFC Gain & Gate Adj. (AV for item 67)70VSUAV 0,1 0 AV V-Sync. Separation Adj. (AV for item 68)71CDMAV 00~07 0 AV V-Countdown Circuit Adj. (AV for item 69)72HLVDRF 0,1 1 Incorrect operation prevention at the time of a special signal (RF mode), 0=Fix, 1=Variable73HLVDAV 0,1 1 Incorrecr operation prevention at the time of a special signal (AV mode), 0=Fix, 1=Variable74VCO-SW 0,1 0 4.43Mhz Coring Adj. 0=for +, 1=for Minu75

VCO-ADJ 00~03 3 C-VCO Adj.76CROSS-BW 00~03 0 Pattern Output. 00=Normal, 01=Black, 02=White, 03=Cross hatch77

AVNCON 00~127 64 Contrast Adj. of the blue back in AV mode. 78AVNBRI 00~127 64 Brightness Adj. of the blue back in AV mode.

0,1 1 SIF Trap Switch. 0=OFF, 1=ON00~255 136

79POMT 00~127 25 Picture Mute at the time of power ON.80CHMT 00~31 10 Picture Mute at the time of channel change.81SYST 00~15 5 Selection of the number of times of a Colour system judgment.82S-STE 0,1 1 AV Stereo/Mono Option. 0=Mono, 1=AV Stereo83VOLTBL 0~1 0 Volume Curve Table. 0=B-Curve, 1=C-Curve84MPP

BASS

0,10,1

1 Multi P-P Option. 0=Without Multi P-P 1=With Multi P-P

A-AGC 0~2

CPU Debug Date.

371 R71 0~255 0 CPU Debug Date.372 R72 0~255 0 CPU Debug Date.

304 R04 0~255CPU Debug Date.303 R03 0~255

CPU Debug Date.

SUB-BT 0~20 AGC Setting of AUDIO IC. 0=OFF, 1=ON(540mV), 2=ON(300mV)

ASTATE 0,1Sub Bass Treble Setting of AUDIO IC. 0= -3db, 1=0db, 2=+3db

SURROUND 0,1Audio Status Option. 0=Without , 1=With Audio Status

Surround Option. 0=Without Surround, 1=With Surround

300 R00 0~255301 R01 0~255

CPU Debug Date.

302 R02 0~255

CPU Debug Date.

1

0

0

00

0

0

858687888990

TRAPT Trap Frequency Adj.00~07 4

OBJECT

IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201IC201CPUCPUCPUCPUCPUCPUCPU

IC3701

IC3701CPUCPU

CPUCPUCPUCPUCPUCPUCPUCPUCPU

1 Bass Expander Option. 0=Without Bass Expander, 1=With Bass Expander

1

Notes: The initial value that the CPU writes down the CPU ROM data to the memory when replaced the memory IC.TV set may not operate correctly with this initial value. It is required to set up the fine adjustment for service adjustments described in the above.

0

-13-

Service Adjustments with Replacing Memory IC(IC802)

TIMER

P

P

ADDRESSDRV

SI. 00100101S2.11111000DATA

B 6421 R 64ADDRESS

V-SCO

SI. 00100101S2.11111000DATA

905

ADDRESSRF AGC

SI. 00100101S2.11111000DATA

3001

[Entering to Service Mode]

1. Press and hold the MENU button on the Remote Control and press the VOLUME (+) button on the TV set.Following setting items appears on the screen.

Display for [V-SCO] V-S Correction adjustment

Read Status

Item No. Item Data value

Display for [RF AGC] RF AGC adjustment

Read Status

Item No. Item Data value

Data value for Red

Display for [DRV] White balance adjustment

Read Status

Item No. Item

Data value for Blue

To return to normal TV mode, press the MENU button on the TV set or the remote control handset.

2. Select item by pressing the TIMER (Item No. UP) or SOUND MUTE (Item No. DOWN) button on the remote controlhandset.

3. Adjust data value by pressing the VOLUME + or VOLUME - button on the remote control handset.

Example

MENU

MENU

0102030405......90... ...9089888786......01

- + PMENUTV/AV

-14-

Service Mode Adjustments

Vertical size

Following adjustments should be carried out when the memory IC is replaced. How to enter the service mode andadjust values, please refer to “ Entering to Service mode” on page 13.

NOTE: Do not attempt this adjustment with weak signal.(1) Tune the receiver to most clearest (or strongest) VHF

station in your area. Set the brightness and contrastcontrols to maximum. Set the colour control to minimum.

(2) Select [RF AGC] in the service mode.(3) Change value until the snow noise just disappears.(4) Exit from service mode.

Item 01 [RF AGC] AGC

(1) Receive a monochrome circular pattern.(2) Set the brightness and contrast to normal.(3) Select [H-PHA] in the service mode.(4) Change value to be optimum horizontal centre position.(5) Exit from service mode.

Item 02 [H-PHA] HORIZONTAL CENTRE

Horizontal centre

(1) Receive a monochrome circular pattern.(2) Set the brightness and contrast to maximum.(3) Select [V-SIZ] in the service mode.(4) Change value to be optimum vertical size.(5) Exit from service mode.

Item 04 [V-SIZ] VERTICAL SIZE

(1) Receive a crosshatch pattern.(2) Set the lever of SW501 (Vertical Center SW) as the

position of a center.(3) Select a picture mode of NATURAL by pressing the

PICTURE MODE button.(4) Select [V-SCO] in the service mode.(5) Adjust Vertical S-letter Correction so that the difference

of “c”, “d” and “e” becomes less than 2 mm by pressingthe VOLUME + or - button.

(6) Confirm Vertical Linearity and adjust Vertical Center then Vertical Size.

(7) Exit from service mode.

Item 05 [V-SCO] V-S CORRECTION

c Upper

Center

Bottom

d

e

(1) Receive a crosshatch pattern.(2) Set the lever of SW501 (Vertical Center SW) as the

position of a center.(3) Select a picture mode of NATURAL by pressing the

PICTURE MODE button.(4) Select [V-LIN] in the service mode.(5) Adjust Vertical Linearity so that the difference of “a” and

“b” becomes less than 3mm by pressing VOLUME + or- button.

(6) Exit from service mode.

Item 06 [V-LIN] VERTICAL LINEARITY

a

b

Upper

Center

Bottom

-15-

1

C515

R487KQ

T471-H5

T471-H1

KDY-1

JP409

JP407

JP403

JP405

C527

C514

R488

J410

R477A

C486

R492

C491

D485

R475

R485

D4

R484

C420C420-H3

D438 KDY

R441

JP411

R477

JP408

JP404

T471-H2

J216

C471

JW24

R483

R481R481A

T471-H7T471-H11

T471-H6T471-H4

T471-H8

T471-H10

T471FBT.

T471A

JP483

L442

R442

FC3A CHASSIS

(1) Receive the monochrome circular pattern.(2) Set the brightness and colour to normal, contrast to maximum.(3) Enter to the service mode.(4) Set each value of Item-14 RBIAS, 15 GBIAS, 16 BBIAS, 17 RDRIV and 19 BDRIV mode to 64.(5) Select Item-20 mode to be one horizontal scanning line and turn the screen volume on the FBT to obtain just visible

one coloured line.(6) Press the 1 (Red Bias -), 2 (Red Bias +), 5 (Green Bias -), 6 (Green Bias +), 9 (Blue Bias -) or 0 (Blue Bias +)

button to adjust the brightness of each colour until a dim white line produced. Please see the control button alloca-tions in this mode.

(7) Select Item-21 DRV mode to enter the white balance adjusting mode.(8) Press the 3 (Red Drive -), 4 (Red Drive +), -/-- (Blue Drive -) or RECALL (Blue Drive +) button alternately to

produce normal black and white picture.(9) Exit from the service mode.(10) Check for proper grey scale tracking at all brightness levels.

NOTE: If the grey scale adjustment is made after picture tube replacement, check the high voltage.

Items 14-17, 19-21 GREY SCALE

Service Mode Adjustments

MAIN BOARD

SCREEN VR(Under side)

0

7

1 4

85

2 3

6

9

P

P

JXMYA

-/--

P P

TV/AV

A B

CH SCAN

TIMER

MENU PIC MODE

SWAP

BASS SURROUND

Red Bias -

Red Bias +

Green Bias -

Blue Bias +

Red Drive +

Blue Drive -

Blue Drive +Green Bias +

Blue Bias -

Red Drive -

Press the MENUbutton to exitfrom servicemode.

JP463

Q461Q461A

Q461-H2

C524

C521

C515

C437

C487JP412

IC50

IC501-H2

T471-H

T471-H1

KDY-6KDY-3KDY-1

R355

R540

C540J503

JW1

R473

D46

R467

D462 C467

R469

D466

R464

C470

C527

R525

R516

C468

C464

R465

R462

D469

R488

D485

C423-H2 C423-H3

C423

C423-H1C420-H1

C420C420-H3

C420-H2

C437A

R422

R424

D438

C441-H2

C441-H3

C

R435

R423

KDY

C441-H1

R441

D461

R466

R461 C463

JP410

JP411

T471-H2

T471-H4 T471FBT.

L442-H1L442-H2

L442

L441-H2

L441-H1

L441-H3L441

D441

R442

JP436

C423A

J540

R514

1

JW15

4

R518

5

R487KQ

IC501-H3

01-H2IC501-H1

T471-H5

JP409

JP407

JP403

JP405

D512

J501

J502

R512

C518

C527

R519

C520

R515

R522

C510

C517

R516

C514

R511R510

J028

J029

D476

R488

J410

R477A

C486

R492

C491

D485

R475

R485

R474

C449

D468

D467

D448

C469

D486

R486

R484

R477

JP408

JP404

J216

C471

JW24

R483

R481R481A

T471-H7T471-H11

T471-H6

T471-H8

T471-H10

T471A

IC501

IC501A

JP483

J504

FC3A CHASSIS

VERT.OUT

E

E

E

E

9

10

9

10

E

JW17

JW16

C425AC424A

Q613-H4

C651-H1C651-H2

C655

D651

T611-H16

C465

R672

D671

R671

J607Q

J605

VR651

R662

R661

D661

R663

R664

J611

R657

Q681

R655

R652

665

J604

J413

R434

C432

T43

C434

R431 Q431

R433

C425C424L432

D439

T43

L652

L651

C651

D652

C652

R644

R643 R631

R628

R624

R623R622

Q612

Q611 L615

D617

D616

C644

C613

L616L613

C615

D611

C618A

C617

C616L611

L612

R629

T611CONVERTER TRANS.

T611-H8

T611-H7

T611-H6

T611-H5

T611-H3

T611-H17

T611-H13

T611-H12

T611-H11

C629

J82

J82

J82

Q613-H2

OUT

Q613A

R445

L462-H3

L462

L462-H2

Q652

J612

C618

+BTP-B

!

-16-

Service Adjustments

(1) Connect a DC meter to TP-B (L631) and the ground.(2) Tune the receiver to an active channel and synchro-

nized picture. Select NATURAL picture mode by press-ing the PICTURE MODE button on the remote control.

(3) Adjust B-voltage to become 130 ± 1V DC by usingVR651.

B-VOLTAGE SUPPLY CHECKING

Note: +B (+130V) Voltage Check and Grayscale Adjustmentmust be completed before attempting High Voltage Check.

(1) Connect high voltage voltmeter negative lead to ground, and connect + lead to anode of picture tube.

(2) Tune receiver to an active channel and confirm TV is operating properly.

(3) Maximize the beam current by adjusting the contrast and brightness controls to maximum. Confirm high volt age is within 24 KV and 26 KV at maximum beam current.

(4) Eliminate the beam current by adjusting the contrast and brightness controls to minimum. Confirm high voltage does not exceed 26.5 KV at zero beam current.

If reading is not within range, check horizontal circuit.

No high-voltage adjustment is provided on this chassis.

HIGH VOLTAGE CHECK

(1) Receive a monochrome circular pattern.(2) Set the brightness to normal and contrast to maximum.(3) Adjust the focus control on the F.B.T. for the best focus

on the screen centre.

FOCUS ADJUSTMENT

TP-B

Focus VR (Upper size)

MAIN BOARD

(1) Receive a monochrome circular pattern.(2) Set the brightness and contrast to maximum.(3) Adjust the vertical centre of the picture with SW501.

VERTICAL CENTRE

Vertical centre

SW501

VR651

(1) Receive a monochrome circular pattern.(2) Set the brightness and contrast to maximum.(3) If the picture is too wide, or narrow, cut or short “JP436”

on the main unit. When “JP436” is shorted, the horizon-tal width increase. When “JP436” is cut, the horizontalwidth decrease.

Important note:When “JP436” is cut, in order to prevent a spark, leave theopening between cutting portions 5mm or more.

HORIZ. WIDTH ADJUSTMENT

JP436

1

E

E

JW15

C524

C521

R518

C515

R487KQ

J024

J515

J516

IC501-H3

IC501-H2IC501-H1

-H1

KDY-6KDY-3KDY-1

L1501

J018

D1032

JP409

JP407

JP405

J1504

J409

J1205

J1206

J1204

J1207

J1208

Q540R540

J1501

D512

J501

J502

R512

C518

C527

R519

C520

R515

R522

SW501

R501

C510

C517

D501

R525

R516

C514

R511R510

J028

J029

D476

R488

J410

R477A

C486

R492

C491

D485

R475

R485

R474

C449

D468

D467

D448

C469

D486

R486

R484

JP408

JP404

C471

JW24

R483

R481R481A

T471-H10

1.

1230

J120330

J021D1402

D1401

C1082

Q1402J025

IC1401VIDEO SW

J026

J209

C1401

JP1502

K1004

IC501

IC501A

JP483

J504

JP501JW

31

FC3A CHASSIS

JW36

VERT.OUT

(SOLDER

SIDE)

IC1501VIDEO

SW

V-CENTER

more than 5mmJP436

-17-

Special Function

Once TUNING LOCK is switched on, further channel tuning(Pre-set) is not possible. The Channel Swapping function alsois not possible.

(2) Tuning Lock setting

The following special functions can be set up on this TVset.

With this function, a maximum sound volume limit can be set atany level.

(3) Music Mode setting

When Music Mode is ON, Programme position from “91” to “99”and “0” are set Music Mode. Only sound is provided and anypicture is not on the screen under Music Mode.

Set AV-START to ON and every time the TV set is switched on,AV position will be the initial programme position.

(4) AV Start setting

TUNING LOCKED

AV

MUSICTurns blackscreen

SOUND BASS ON 18

(1) Volume Lock setting

(5) Language selection for the on screen display

Either Thai or English can be selected as the language of thescreen display.

1To enter into the special function setting mode, press and hold the MENU button of the remote control, then press thePROGRAMME DOWN button on the TV set.

2 Select an item of the special functions by pressing the PROGRAMME UP or DOWN button on the remote control or the TV set.

3 Set the selected special function “ ON “ by pressing the VOLUME + or - button. To cancel, set to “ OFF”.

How to set the special function:

Note: When making the VOLUME LOCK setting, set thedesired maximum sound volume by pressing the VOLUME + or- button before entering Special Function setting mode.

4 Press the MENU button of the remote control to return to the normal TV mode.

P

P

P

P

MENU

OFFOFFOFFOFF

TUNING LOCK

AV START

VOLUME LOCK

MUSIC MODE

SELECT ADJUST M EXIT

OFFONOFFOFF

TUNING LOCK

AV START

VOLUME LOCK

MUSIC MODE


LANG / ENGLISH

To select language:1) Select LANG/ by pressing the PRGRAMME UP or

DOWN button.2) Select either Thai or English by pressing the VOLUME + or

- button.

LANG / ENGLISH

TUNING LOCK

AV START

VOLUME LOCK

MUSIC MODE

OFFOFFOFFOFF


LANG / ENGLISH

MENU

- + P

-18-

Purity and Convergence Adjustment

RED

BLUE

Adjust tabs together tosuperimpose red andblue horizontal line.

Figure- 2 BLUE AND RED LINE MOVEMENT Figure- 3 BLUE/RED AND GREEN MOVEMENT

Adjust tabs together tosuperimpose red/blueand green horizontalline.

Adjust tabs angle to superimposeblue and red vertical line.

Adjust tabs angle to superimposered/blue and green vertical line.

GREEN

BLUE / RED

CAUTION: The Convergence and Purity adjustments have been made at the factory. Readjustmentshould be made only after picture tube or deflection yoke replacement, following the steps below:

PURITY ADJUSTMENT1. Demagnetize the picture tube and receiver using an external

degaussing coil. When replacing picture tube or deflectionyoke, mount deflection yoke and purity-convergence magnetsassembly properly, see figures 1 and 4.

2. Turn Red and Blue guns off and provide only Green raster.Rotate Screen control to fully counterclockwise. Rotate Redand Blue Bias controls fully counterclockwise. Slowly rotateGreen Bias control clockwise to produce Green raster.

3. Loosen the screw holding the Deflection Yoke and remove the3 Rubber Wedges, and slide the Deflection Yoke fully forward.

4. Rotate and spread the Tabs of the two Purity Magnets to cen-tre the vertical green belt in the picture screen. The PurityMagnets are also adjusted to obtain vertical centring of theraster.

5. Slowly slide the Deflection Yoke backward until a uniformgreen screen is obtained.

6. Check the purity of the red and blue screens for uniformity,turn off other colours to check this (use bias controls).Readjust the yoke position if necessary until all screens arepure.

7. Adjust each Bias control and screen control to obtain whiteraster. Refer to Gray Scale Adjustment. If part of the picturescreen is coloured, adjust the Deflection Yoke position forwardor backward slightly.

8. Tighten the mounting screw of the Deflection Yoke. AdjustConvergence next.

CENTRE CONVERGENCE ADJUSTMENT1. Use a dot crosshatch pattern signal.2. Turn Red and Blue guns on and turn off Green gun. Adjust the

angle between the Tabs of the Four Pole Magnet 1 and 2, andsuperimpose the Red and Blue vertical lines in the centre areaof the picture screen. Refer to figure 2.

3. Keeping the mutual angle of the Tabs of the Four Pole Magnetturn them together to superimpose the Blue and Red horizon-tal lines in the centre area of the picture screen. Refer to fig-ure 2.

4. Turn Green gun on and adjust Six Pole Magnet 3 and 4 thatthe Green line superimposed on the Red/Blue lines.This is the same procedure used in steps 2 and 3.Refer to figure 3.

OUTER AREA CONVERGENCE ADJUSTMENTSlightly loosen the screw holding the Deflection Yoke. Adjust theDeflection Yoke to converge the detail in the outer area (left sideand right side) of the picture screen by orbital movement of thefront of the Yoke, then secure the Deflection Yoke in appropriateposition by putting the wedges as illustrated. Tighten screw hold-ing the Deflection Yoke.

RUBBERWEDGE

DEFLECTION YOKE

DEFLECTION YOKEMOUNTING SCREW

Figure 4. Deflection Yoke Movement

SIX-POLEMAGNET TABS FOUR-POLE

MAGNET TABS

ANGLEOF TABS

PURITYMAGNETTABS

432

1

FOCUS GAP(G3-G4)

Figure 1. Purity and Convergence Magnets

MAGNET TABS

ANGLE OF MAGNET TABS

Figure 5. Adjusting Magnet

Note: The form of deflection yoke changes with models.

-19-

Cabinet Parts List C2GW

Note: Parts order must contain Service Ref. No., Part No., and descriptions.

0

7

1 4

85

2 3

6

9

P

P

JXMYA

-/--

P P

TV/AV

A B

CH SCAN

TIMER

MENU PIC MODE

SWAP

BASS SURROUND

11

12

Key No. Part No. Description

9

- + PMENUTV/AV

4-a 53 2

1 610 286 4977 ASSY,BUTTON POWER-C2GA610 286 7770 SPRING COIL-C2GA

2 610 286 5097 DEC IND-C2GA3 610 286 4984 ASSY,BUTTON UNITED-C2GA4 610 292 3056 ASSY,CABINET FRONT-C2GS 4-a 610 292 3117 CABINET FRONT-C2GS4-b 610 286 5080 DOOR-C2GA

5 610 284 7741 DOOR COVER-C2SA6 610 288 4791 DEC SHEET DOOR-C2GA7 645 041 7269 BADGE,SANYO

8 610 301 9031 CABINET BACK-C2GW9 610 302 0730 LABEL RATING-C2GW

10 610 256 7670 HOLDER AC CORD-SGP-D4VA

11 645 054 3579 ASSY,REMOCON JXMYA12 610 300 5102 RC-BATTERY LID-JXMYA

610 302 2826 INSTRUCTION MANUAL-C2GW

Key No. Part No. Description

1

L

R

AUDIO

AV1 INPUT

VIDEO

(MONO)

S-VIDEO

MONITOROUT

ANT. 75Ω

7

8

10

4-b

6

L-AUDIO-RVIDEOAV2 INPUT

-20-

C2GW

OUT OF CIRCUIT BOARD PICTURE TUBE

Q901 414 011 8403 CRT A51LVG896X Q901A 645 008 8674 MAGNET,CG.PR

610 003 1739 CG PURITY MAGNET Q901B1 610 233 7891 DY SPACER E2HA

610 290 4154 DY SPACER-F8LZ Q901B2 610 233 7891 DY SPACER E2HA

610 290 4154 DY SPACER-F8LZ Q901B3 610 233 7891 DY SPACER E2HA

610 290 4154 DY SPACER-F8LZ

COILL901 645 040 0247 COIL,DEGAUSSING

645 046 1729 COIL,DEGAUSSING L902 645 057 2401 YOKE,DEFLECTION

MISCELLANEOUSSP901 645 032 2037 SPEAKER,8

652 001 0871 SPEAKER,8 SP902 645 032 2037 SPEAKER,8

652 001 0871 SPEAKER,8 W901 645 009 9991 CORD,POWER

645 048 2106 CORD,POWER W902 610 283 5335 ASSY,WIRE GND CONNECTOR C

610 283 7179 ASSY,WIRE GND CONNECTOR C

610 305 0157 ASSY,PWB,MAIN C2GW1AA0B10S1000A

TRANSISTORQ001 405 014 4509 TR 2SC2412K T146 R

405 014 4608 TR 2SC2412K T146 S 405 015 8704 TR 2SC2812-L6-TB 405 015 8902 TR 2SC2812-L7-TB 405 163 1602 TR 2SC2812N-L6-TB0 405 163 1701 TR 2SC2812N-L7-TB0

Q111 405 015 9701 TR 2SC2814-F4-TB Q1230 405 014 4509 TR 2SC2412K T146 R


Q1231 405 011 8401 TR 2SC1740S-Q 405 011 8500 TR 2SC1740S-R 405 011 8609 TR 2SC1740S-S 405 012 2002 TR 2SC1815-GR 405 012 2101 TR 2SC1815-O 405 012 2309 TR 2SC1815-Y 405 020 7501 TR 2SC945A-PA 405 020 7709 TR 2SC945A-QA 405 020 7907 TR 2SC945A-RA

Q1401 405 134 5905 TR 2SA1037AK-T146-R 405 147 2205 TR 2SA1037AK-S-T146

!

!

!

!

Chassis Electrical Parts List

Ref. No. Part No. Description Ref. No. Part No. Description

Product safety should be considered when a component replacement is made in any area of a receiver. Components indicated by a mark in this parts list and the circuit diagram show components whose value havespecial significance to product safety. It is particularly recommended that only parts specified on the following partslist be used for components replacement pointed out by the mark.

!

Note: Parts order must contain Service Ref. No., Part No., and descriptions. The main PCB unit will be supplied without tuner andflyback transformer. They should be ordered separately.

Read description in the Capacitor and Resistor as follows:

CAPACITORCERAMIC 100P K 50V

Rated Voltage

Tolerance Symbols:Less than 10pFA : Not specified B : ±0.1pF C : ±0.25pFD : ±0.5pF F : ±1PF G : ±2pFR : ±0.25-0pF S : ±0-0.25pF E : +0-1pFMore than 10pFA : Not specified B : ±0.1% C : ±0.25%D : ±0.5% F : ±1% G : ±2%H : ±3% J : ±5% K : ±10%L : ±15% M : ±20% N : ±30%P : +100-0% Q : +30-10% T : +50-10%U : +75-10% V : +20-10% W : +100-10%X : +40-20% Y : +150-10% Z : +80-20%

Rated value: P=pico farad, U=micro farad

Material:CERAMIC........... CeramicMT-PAPER......... Metallized PaperPOLYESTER...... PolyesterMT-POLYEST.....Metallized PolyesterPOLYPRO.......... PolypropyleneMT-POLYPRO....Metallized PolypropyleneCOMPO FILM.....Composite filmMT-COMPO........Metallized CompositeSTYRENE...........StyreneTA-SOLID........... Tantalum SolidAL-SOLID........... Aluminium SolidELECT................ElectrolyticNP-ELECT..........Non-polarised ElectrolyticOS-SOLID.......... Aluminium Solid with Organic Semiconductive ElectrolyticDL-ELECT.......... Double Layered Electrolytic

RESISTORCARBON 4.7K J A 1/4W

Rated Wattage

Performance Symbols:A: General B: Non flammable Z: Low noiseOther: Temperature coefficient

Tolerance Symbols:A: ±0.05% B: ±0.1% C: ±0.25% D: ±0.5%F: ±1% G: ±2% J: ±5% K: ±10%M: ±20% P: +5-15%

Rated value, ohms:K: 1,000, M: 1,000,000

Material:CARBON........... CarbonMT-FILM............ Metal FilmOXIDE-MT......... Oxide Metal FilmSOLID................ CompositionMT-GLAZE......... Metal GlazeWIRE WOUND...Wire WoundCERAMIC RES.. CeramicFUSIBLE RES....Fusible

NOTES:

405 002 0308 TR 2SA1037K T146 R 405 002 0407 TR 2SA1037K T146 S 405 002 6706 TR 2SA1179-M6-TB 405 002 6904 TR 2SA1179-M7-TB 405 163 1503 TR 2SA1179N-M6-TB 405 163 2708 TR 2SA1179N-M7-TB

Q1402 406 000 6804 TR 2SA1015-G(SAN)-TPE2 405 001 7407 TR 2SA1015-O(SAN) 405 001 7605 TR 2SA1015-Y(SAN) 405 004 3109 TR 2SA564A-Q(CU) 405 004 3208 TR 2SA564A-R(CU) 405 006 1707 TR 2SA933S-Q 405 006 1806 TR 2SA933S-R

Q1501 405 014 4509 TR 2SC2412K T146 R 405 014 4608 TR 2SC2412K T146 S 405 015 8704 TR 2SC2812-L6-TB 405 015 8902 TR 2SC2812-L7-TB 405 163 1602 TR 2SC2812N-L6-TB0 405 163 1701 TR 2SC2812N-L7-TB0

Q1502 405 134 5905 TR 2SA1037AK-T146-R 405 147 2205 TR 2SA1037AK-S-T146 405 002 0308 TR 2SA1037K T146 R 405 002 0407 TR 2SA1037K T146 S 405 002 6706 TR 2SA1179-M6-TB 405 002 6904 TR 2SA1179-M7-TB 405 163 1503 TR 2SA1179N-M6-TB 405 163 2708 TR 2SA1179N-M7-TB







Q190 405 134 5905 TR 2SA1037AK-T146-R 405 147 2205 TR 2SA1037AK-S-T146 405 002 0308 TR 2SA1037K T146 R 405 002 0407 TR 2SA1037K T146 S

405 002 6706 TR 2SA1179-M6-TB 405 002 6904 TR 2SA1179-M7-TB 405 163 1503 TR 2SA1179N-M6-TB 405 163 2708 TR 2SA1179N-M7-TB

Q1902 406 000 6804 TR 2SA1015-G(SAN)-TPE2 405 001 7407 TR 2SA1015-O(SAN) 405 001 7605 TR 2SA1015-Y(SAN) 405 004 3109 TR 2SA564A-Q(CU) 405 004 3208 TR 2SA564A-R(CU) 405 006 1707 TR 2SA933S-Q 405 006 1806 TR 2SA933S-R



Q431 405 018 0507 TR 2SC3332-R 405 018 0606 TR 2SC3332-S

Q432 405 157 1304 TR 2SD2634-YB Q449 405 014 4509 TR 2SC2412K T146 R



Q611 405 013 6702 TR 2SC2274-D 405 013 6801 TR 2SC2274-E 405 013 7006 TR 2SC2274-F

Q612 405 006 6504 TR 2SA984-E 405 006 6702 TR 2SA984-F

Q613 405 175 8101 TR 2SK2766 Q615 405 011 8401 TR 2SC1740S-Q

405 011 8500 TR 2SC1740S-R 405 011 8609 TR 2SC1740S-S 405 012 2002 TR 2SC1815-GR 405 012 2309 TR 2SC1815-Y 405 020 7501 TR 2SC945A-PA 405 020 7709 TR 2SC945A-QA

Q621 405 011 8401 TR 2SC1740S-Q 405 011 8500 TR 2SC1740S-R 405 011 8609 TR 2SC1740S-S 405 012 2002 TR 2SC1815-GR 405 012 2309 TR 2SC1815-Y 405 020 7501 TR 2SC945A-PA 405 020 7709 TR 2SC945A-QA

Q625 405 016 9403 TR 2SC3068 Q641 406 000 6804 TR 2SA1015-G(SAN)-TPE2

405 001 7605 TR 2SA1015-Y(SAN) 405 004 3208 TR 2SA564A-R(CU) 405 006 1806 TR 2SA933S-R

Q642 405 011 8401 TR 2SC1740S-Q 405 011 8500 TR 2SC1740S-R 405 011 8609 TR 2SC1740S-S 405 012 2002 TR 2SC1815-GR

-21-

C2GW


-22-

C2GW

405 012 2309 TR 2SC1815-Y 405 020 7501 TR 2SC945A-PA 405 020 7709 TR 2SC945A-QA


Q652 405 089 0000 TR 2SA1707-S 405 089 0109 TR 2SA1707-T 405 009 6907 TR 2SB985-S 405 009 7003 TR 2SB985-T

Q653 405 089 0000 TR 2SA1707-S 405 089 0109 TR 2SA1707-T 405 009 6907 TR 2SB985-S 405 009 7003 TR 2SB985-T

Q654 405 059 9804 TR 2SD1913-Q-RA 405 059 9903 TR 2SD1913-R-RA

Q661 405 011 8401 TR 2SC1740S-Q 405 011 8500 TR 2SC1740S-R 405 011 8609 TR 2SC1740S-S 405 012 2002 TR 2SC1815-GR 405 012 2309 TR 2SC1815-Y 405 020 7501 TR 2SC945A-PA 405 020 7709 TR 2SC945A-QA 405 020 7907 TR 2SC945A-RA

Q662 406 000 6804 TR 2SA1015-G(SAN)-TPE2 405 001 7605 TR 2SA1015-Y(SAN) 405 004 3208 TR 2SA564A-R(CU) 405 006 1806 TR 2SA933S-R


Q681 405 011 8401 TR 2SC1740S-Q 405 011 8500 TR 2SC1740S-R 405 011 8609 TR 2SC1740S-S 405 012 2002 TR 2SC1815-GR 405 012 2101 TR 2SC1815-O 405 012 2309 TR 2SC1815-Y 405 020 7501 TR 2SC945A-PA 405 020 7709 TR 2SC945A-QA 405 020 7907 TR 2SC945A-RA

Q861 405 134 5905 TR 2SA1037AK-T146-R 405 147 2205 TR 2SA1037AK-S-T146 405 002 0308 TR 2SA1037K T146 R 405 002 0407 TR 2SA1037K T146 S 405 002 6706 TR 2SA1179-M6-TB 405 002 6904 TR 2SA1179-M7-TB 405 163 1503 TR 2SA1179N-M6-TB 405 163 2708 TR 2SA1179N-M7-TB


Q881 405 014 4509 TR 2SC2412K T146 R 405 014 4608 TR 2SC2412K T146 S 405 015 8704 TR 2SC2812-L6-TB 405 015 8902 TR 2SC2812-L7-TB 405 163 1602 TR 2SC2812N-L6-TB0

405 163 1701 TR 2SC2812N-L7-TB0 Q886 405 014 4509 TR 2SC2412K T146 R


INTEGRATED CIRCUITIC001 409 379 2903 IC TA8200AH IC1201 409 051 2702 IC TC4052BF-TP1 IC1401 409 479 3206 IC MM1188XS IC1501 409 051 2900 IC TC4053BF-TP1 IC201 409 517 5902 IC LA76818A IC202 409 124 5302 IC L78M05T IC3701 409 526 7409 IC NJW1138M IC3702 409 051 2900 IC TC4053BF-TP1 IC501 409 507 0900 IC LA78040N

409 510 1109 IC TDA9302H IC681 409 241 5407 IC BA178M05T

409 265 4806 IC L78M05CV 409 172 1509 IC MC78M05CT 409 320 5700 IC UPC78M05AHF

IC801 410 445 1706 IC LC863440W-50K0-TLM IC802 409 383 6805 IC 24LC08B/P

CAPACITORC003 403 258 8208 NP-ELECT 10U M 16V C004 403 258 8208 NP-ELECT 10U M 16V C005 403 043 6006 ELECT 330U M 16V C006 403 049 9803 ELECT 2.2U M 50V C007 403 048 6308 ELECT 0.47U M 50V C008 403 043 6006 ELECT 330U M 16V C009 403 047 3100 ELECT 47U M 25V C010 403 047 3100 ELECT 47U M 25V C011 403 305 3507 CERAMIC 0.1U Z 50V C013 403 305 3507 CERAMIC 0.1U Z 50V C018 403 233 1903 ELECT 3300U M 35V C020 403 045 1504 ELECT 1000U M 25V C021 403 215 2201 CERAMIC 0.01U K 50V C022 403 045 1504 ELECT 1000U M 25V C023 403 215 2201 CERAMIC 0.01U K 50V C024 403 237 7901 MT-COMPO 0.22U J 50V C025 403 237 7901 MT-COMPO 0.22U J 50V C1000 403 041 8804 ELECT 10U M 16V C1001 403 041 8804 ELECT 10U M 16V C1002 403 041 8804 ELECT 10U M 16V C101 403 044 1703 ELECT 470U M 16V C1030 403 041 8804 ELECT 10U M 16V C1031 403 041 8804 ELECT 10U M 16V C1032 403 041 8804 ELECT 10U M 16V C106 403 051 3103 ELECT 47U M 50V C1060 403 041 8804 ELECT 10U M 16V C1061 403 041 8804 ELECT 10U M 16V C1062 403 043 0202 ELECT 220U M 16V C107 403 051 3103 ELECT 47U M 50V C1081 403 215 2201 CERAMIC 0.01U K 50V C1082 403 041 8804 ELECT 10U M 16V C1084 403 215 2201 CERAMIC 0.01U K 50V C111 403 149 9208 CERAMIC 0.01U Z 50V C112 403 149 9208 CERAMIC 0.01U Z 50V C113 403 149 9208 CERAMIC 0.01U Z 50V C120 403 224 6603 CERAMIC 0.022U Z 50V C121 403 149 9208 CERAMIC 0.01U Z 50V C122 403 042 2405 ELECT 100U M 16V C123 401 105 7909 MT-GLAZE 0.000 ZA 1/16W C1230 403 041 8804 ELECT 10U M 16V


C1231 403 041 8804 ELECT 10U M 16V C124 403 149 9208 CERAMIC 0.01U Z 50V C132 403 048 6308 ELECT 0.47U M 50V C135 403 048 6308 ELECT 0.47U M 50V C138 403 224 6603 CERAMIC 0.022U Z 50V C1401 403 042 2405 ELECT 100U M 16V C1402 403 149 9208 CERAMIC 0.01U Z 50V C1501 403 149 9208 CERAMIC 0.01U Z 50V C171 403 113 3805 CERAMIC 1000P K 50V C172 403 305 3507 CERAMIC 0.1U Z 50V C174 403 157 1904 CERAMIC 10P D 50V C1902 403 050 2800 ELECT 22U M 50V C201 403 086 2300 NP-ELECT 1U M 50V C202 403 249 9009 MT-COMPO 0.015U J 50V C203 403 149 9208 CERAMIC 0.01U Z 50V C204 403 049 4204 ELECT 10U M 50V C205 403 049 4204 ELECT 10U M 50V C206 403 305 3507 CERAMIC 0.1U Z 50V C207 403 305 3507 CERAMIC 0.1U Z 50V C208 403 113 3805 CERAMIC 1000P K 50V C209 403 048 6308 ELECT 0.47U M 50V C210 403 042 4805 ELECT 1000U M 16V C212 403 155 4204 CERAMIC 15P J 50V C221 403 305 3507 CERAMIC 0.1U Z 50V C222 403 305 3507 CERAMIC 0.1U Z 50V C223 403 305 3507 CERAMIC 0.1U Z 50V C224 403 224 7006 CERAMIC 0.047U Z 50V C225 403 049 0008 ELECT 1U M 50V C226 403 049 0008 ELECT 1U M 50V C227 403 086 2300 NP-ELECT 1U M 50V C231 403 260 2904 MT-COMPO 0.33U J 50V C232 403 260 2904 MT-COMPO 0.33U J 50V C233 403 049 4204 ELECT 10U M 50V C240 403 149 9208 CERAMIC 0.01U Z 50V C243 403 149 9208 CERAMIC 0.01U Z 50V C244 403 051 3103 ELECT 47U M 50V C245 403 086 2300 NP-ELECT 1U M 50V C246 403 049 0008 ELECT 1U M 50V C247 403 049 9803 ELECT 2.2U M 50V C270 403 157 3601 CERAMIC 100P J 50V C271 403 157 3601 CERAMIC 100P J 50V C273 403 305 3507 CERAMIC 0.1U Z 50V C275 403 051 3103 ELECT 47U M 50V C276 403 051 3103 ELECT 47U M 50V C283 403 149 9208 CERAMIC 0.01U Z 50V C358 403 049 0008 ELECT 1U M 50V C3701 403 042 7707 ELECT 22U M 16V C3702 403 069 8305 CERAMIC 0.01U Z 50V C3711 403 051 0607 ELECT 4.7U M 50V C3712 403 051 0607 ELECT 4.7U M 50V C3713 403 061 8303 POLYESTER 4700P K 50V

403 061 8808 POLYESTER 4700P K 50V 403 179 1104 POLYESTER 4700P K 50V

C3714 403 367 0407 CERAMIC 0.1U K 50V C3716 403 049 0008 ELECT 1U M 50V C3717 403 367 0407 CERAMIC 0.1U K 50V C3718 403 051 0607 ELECT 4.7U M 50V C3719 403 051 0607 ELECT 4.7U M 50V C3721 403 051 0607 ELECT 4.7U M 50V C3722 403 051 0607 ELECT 4.7U M 50V C3723 403 155 2309 CERAMIC 4700P K 50V C3724 403 367 0407 CERAMIC 0.1U K 50V C3726 403 367 0407 CERAMIC 0.1U K 50V C3727 403 051 0607 ELECT 4.7U M 50V C3728 403 051 0607 ELECT 4.7U M 50V C3729 403 051 0607 ELECT 4.7U M 50V C3741 403 041 8804 ELECT 10U M 16V

C3742 403 041 8804 ELECT 10U M 16V C420 404 077 4709 MT-POLYPRO 8000P H 1.5K C423A 403 275 8403 CERAMIC 390P K 3K

403 275 8403 CERAMIC 390P K 3K 403 275 8403 CERAMIC 390P K 3K 403 232 3106 CERAMIC 390P K 3K

C432 403 075 7101 CERAMIC 1000P K 500V C433 403 076 3102 CERAMIC 3900P K 500V C434 403 054 0703 ELECT 47U M 35V C437 403 066 6106 MT-POLYEST 0.47U J 250V C441 403 078 9300 MT-POLYPRO 0.15U J 200V C449 403 041 8804 ELECT 10U M 16V C469 403 049 4204 ELECT 10U M 50V C471 404 056 5307 NP-ELECT 2.2U M 100V

404 045 6605 NP-ELECT 2.2U M 50V C486 403 260 0702 ELECT 33U M 250V C491 403 076 5304 CERAMIC 680P K 500V C510 403 042 7707 ELECT 22U M 16V C511 403 149 9208 CERAMIC 0.01U Z 50V C514 403 049 4204 ELECT 10U M 50V C515 403 045 9807 ELECT 2200U M 25V C517 403 053 2104 ELECT 220U M 35V C520 403 064 1202 POLYESTER 0.1U K 100V

403 276 9706 POLYESTER 0.1U K 100V C521 403 053 3606 ELECT 2200U M 35V C524 403 288 9107 POLYESTER 0.22U K 100V C527 403 049 4204 ELECT 10U M 50V C601 404 072 7903 MT-POLYEST 0.068U K 250V

404 072 6104 MT-POLYEST 0.068U M 250V 404 079 6503 MT-POLYEST 0.068U M 250V 404 073 7506 MT-POLYEST 0.068U M 275V

C602 404 071 2107 MT-POLYEST 0.1U K 250V 404 072 5602 MT-POLYEST 0.1U M 250V 404 060 7205 MT-POLYEST 0.1U M 250V 404 066 1702 MT-POLYEST 0.1U M 275V

C608 403 076 6707 CERAMIC 1000P K 1K 403 312 8205 CERAMIC 1000P K 1K 403 271 9602 CERAMIC 1000P K 1K

C609 404 051 8105 ELECT 270U M 400V 404 078 7600 ELECT 270U M 400V

C611 403 056 9704 POLYESTER 0.01U J 50V 403 178 9309 POLYESTER 0.01U J 50V

C612 403 138 9905 POLYESTER 470P J 50V 403 276 9102 POLYESTER 470P J 50V

C613 403 057 3107 POLYESTER 0.1U K 50V 403 181 8207 POLYESTER 0.1U K 50V

C614 403 237 7901 MT-COMPO 0.22U J 50V C615 403 324 3304 CERAMIC 220P K 2K

403 324 3304 CERAMIC 220P K 2K C617 403 324 3304 CERAMIC 220P K 2K C618 403 314 5103 MT-POLYEST 0.047U K 630V C628 404 073 3904 CERAMIC 1000P K 250V

404 073 2105 CERAMIC 1000P M 250V 404 071 3302 CERAMIC 1000P M 400V

C629 404 073 3904 CERAMIC 1000P K 250V 404 073 2105 CERAMIC 1000P M 250V 404 071 3302 CERAMIC 1000P M 400V

C643 403 148 0404 ELECT 1000U M 25V C644 403 047 3100 ELECT 47U M 25V C651 404 074 9103 ELECT 220U M 160V C652 403 148 2002 ELECT 470U M 35V C654 403 053 3606 ELECT 2200U M 35V C655 403 262 4401 CERAMIC 680P K 1K

403 262 4401 CERAMIC 680P K 1K C656 403 331 6404 CERAMIC 1500P K 1K C663 403 049 0008 ELECT 1U M 50V C664 403 041 8804 ELECT 10U M 16V

!

!

!

-23-

C2GW


-24-

C2GW

C665 403 044 1703 ELECT 470U M 16V C681 403 039 9004 ELECT 1000U M 10V C801 403 155 4204 CERAMIC 15P J 50V C802 403 157 2505 CERAMIC 27P J 50V C803 403 149 9208 CERAMIC 0.01U Z 50V C804 403 224 7006 CERAMIC 0.047U Z 50V C805 403 041 8804 ELECT 10U M 16V C806 403 164 0204 CERAMIC 0.1U Z 25V C811 403 149 9208 CERAMIC 0.01U Z 50V C816 403 149 9208 CERAMIC 0.01U Z 50V C823 403 164 0204 CERAMIC 0.1U Z 25V C824 403 305 3507 CERAMIC 0.1U Z 50V C825 403 157 3601 CERAMIC 100P J 50V C826 403 164 0204 CERAMIC 0.1U Z 25V C828 403 149 9208 CERAMIC 0.01U Z 50V C829 403 164 0204 CERAMIC 0.1U Z 25V C832 403 149 9208 CERAMIC 0.01U Z 50V C835 403 049 0008 ELECT 1U M 50V C836 403 157 3106 CERAMIC 56P J 50V C837 403 157 3106 CERAMIC 56P J 50V C851 403 157 3106 CERAMIC 56P J 50V C852 403 157 3106 CERAMIC 56P J 50V C853 403 157 3106 CERAMIC 56P J 50V C856 403 113 3805 CERAMIC 1000P K 50V C861 403 047 8402 ELECT 0.1U M 50V C862 403 164 0204 CERAMIC 0.1U Z 25V C880 403 155 2200 CERAMIC 3300P K 50V C892 403 164 0204 CERAMIC 0.1U Z 25V C893 403 049 9803 ELECT 2.2U M 50V C894 403 333 5108 CERAMIC 0.033U K 50V

RESISTORR001 401 007 7601 CARBON 150 JA 1/2W R002 401 007 7601 CARBON 150 JA 1/2W R003 401 105 0603 MT-GLAZE 10K JA 1/16W R004 401 105 2805 MT-GLAZE 2.2K JA 1/16W R005 401 105 2805 MT-GLAZE 2.2K JA 1/16W R006 401 105 2805 MT-GLAZE 2.2K JA 1/16W R007 401 105 4205 MT-GLAZE 33K JA 1/16W R008 401 105 0603 MT-GLAZE 10K JA 1/16W R010 401 026 1000 CARBON 2.7K JA 1/6W R013 401 010 1504 CARBON 4.7 JA 1/2W R016 401 022 1905 CARBON 680 JA 1/4W R017 401 022 1905 CARBON 680 JA 1/4W R018 401 010 1504 CARBON 4.7 JA 1/2W R020 402 069 9800 WIRE WOUND 2.7 KA 5W

402 069 9909 WIRE WOUND 2.7 KA 5W R1000 401 105 1402 MT-GLAZE 150 JA 1/16W R1001 401 105 2805 MT-GLAZE 2.2K JA 1/16W R1002 401 105 0603 MT-GLAZE 10K JA 1/16W R1003 401 105 2805 MT-GLAZE 2.2K JA 1/16W R1004 401 105 0603 MT-GLAZE 10K JA 1/16W R101 401 105 7909 MT-GLAZE 0.000 ZA 1/16W R103 401 061 8101 OXIDE-MT 39K JA 1W R1030 401 105 1402 MT-GLAZE 150 JA 1/16W R1031 401 105 2805 MT-GLAZE 2.2K JA 1/16W R1032 401 105 0702 MT-GLAZE 100K JA 1/16W R1033 401 027 9005 CARBON 82K JA 1/6W R1034 401 105 2805 MT-GLAZE 2.2K JA 1/16W R1035 401 105 0702 MT-GLAZE 100K JA 1/16W R1036 401 027 9005 CARBON 82K JA 1/6W R106 401 024 6700 CARBON 100 JA 1/6W R1060 401 027 6608 CARBON 75 JA 1/6W R1063 401 105 5905 MT-GLAZE 560 JA 1/16W R1064 401 105 0702 MT-GLAZE 100K JA 1/16W R1065 401 105 5905 MT-GLAZE 560 JA 1/16W R1066 401 105 0702 MT-GLAZE 100K JA 1/16W

R107 401 024 6700 CARBON 100 JA 1/6W R1075 401 105 1402 MT-GLAZE 150 JA 1/16W R1076 401 105 1402 MT-GLAZE 150 JA 1/16W R108 401 025 4606 CARBON 18K JA 1/6W R1081 401 113 4402 MT-GLAZE 75 JA 1/16W R1082 401 113 4402 MT-GLAZE 75 JA 1/16W R109 401 105 8203 MT-GLAZE 68K JA 1/16W R111 401 105 0504 MT-GLAZE 1K JA 1/16W R112 401 105 6001 MT-GLAZE 5.6K JA 1/16W R114 401 105 4007 MT-GLAZE 330 JA 1/16W R115 401 027 2105 CARBON 56 JA 1/6W R116 401 105 5806 MT-GLAZE 56 JA 1/16W R1200 401 105 7909 MT-GLAZE 0.000 ZA 1/16W R1230 401 105 7503 MT-GLAZE 82K JA 1/16W R1231 401 024 9701 CARBON 12K JA 1/6W R1232 401 105 6605 MT-GLAZE 6.8K JA 1/16W R1233 401 027 9005 CARBON 82K JA 1/6W R1234 401 105 5202 MT-GLAZE 470 JA 1/16W R1236 401 105 5202 MT-GLAZE 470 JA 1/16W R1237 401 105 5301 MT-GLAZE 4.7K JA 1/16W R1239 401 105 5301 MT-GLAZE 4.7K JA 1/16W R130 401 105 7909 MT-GLAZE 0.000 ZA 1/16W R132 401 105 5202 MT-GLAZE 470 JA 1/16W R140 401 105 7909 MT-GLAZE 0.000 ZA 1/16W R1401 401 105 5202 MT-GLAZE 470 JA 1/16W R1402 401 105 5202 MT-GLAZE 470 JA 1/16W R1403 401 105 0603 MT-GLAZE 10K JA 1/16W R1405 401 105 0603 MT-GLAZE 10K JA 1/16W R1406 401 105 0603 MT-GLAZE 10K JA 1/16W R1501 401 105 0504 MT-GLAZE 1K JA 1/16W R1502 401 105 3208 MT-GLAZE 270 JA 1/16W R1503 401 105 7909 MT-GLAZE 0.000 ZA 1/16W R1504 401 105 3406 MT-GLAZE 27K JA 1/16W R1505 401 105 5400 MT-GLAZE 47K JA 1/16W R1506 401 105 3208 MT-GLAZE 270 JA 1/16W R171 401 105 1501 MT-GLAZE 1.5K JA 1/16W R172 401 105 0504 MT-GLAZE 1K JA 1/16W R174 401 105 0405 MT-GLAZE 100 JA 1/16W R175 401 105 5202 MT-GLAZE 470 JA 1/16W R176 401 105 0603 MT-GLAZE 10K JA 1/16W R177 401 105 0504 MT-GLAZE 1K JA 1/16W R178 401 105 0504 MT-GLAZE 1K JA 1/16W R180 401 105 1501 MT-GLAZE 1.5K JA 1/16W R188 401 105 1006 MT-GLAZE 1.2K JA 1/16W R1901 401 105 3406 MT-GLAZE 27K JA 1/16W R1902 401 105 1105 MT-GLAZE 12K JA 1/16W R1903 401 105 6001 MT-GLAZE 5.6K JA 1/16W R1904 401 105 4601 MT-GLAZE 3.9K JA 1/16W R1905 401 105 2805 MT-GLAZE 2.2K JA 1/16W R1906 401 105 2003 MT-GLAZE 1.8K JA 1/16W R1907 401 024 6700 CARBON 100 JA 1/6W R1911 401 025 7409 CARBON 220 JA 1/6W R1912 401 025 7409 CARBON 220 JA 1/6W R1913 401 025 7409 CARBON 220 JA 1/6W R195 401 105 5202 MT-GLAZE 470 JA 1/16W R206 401 105 7909 MT-GLAZE 0.000 ZA 1/16W R207 401 105 7909 MT-GLAZE 0.000 ZA 1/16W R208 401 105 0504 MT-GLAZE 1K JA 1/16W R210 401 105 3703 MT-GLAZE 3K JA 1/16W R211 401 025 1308 CARBON 150 JA 1/6W R212 401 105 1402 MT-GLAZE 150 JA 1/16W R221 401 105 0504 MT-GLAZE 1K JA 1/16W R222 401 105 0504 MT-GLAZE 1K JA 1/16W R223 401 105 0504 MT-GLAZE 1K JA 1/16W R224 401 105 5301 MT-GLAZE 4.7K JA 1/16W R225 401 105 5301 MT-GLAZE 4.7K JA 1/16W R226 401 105 2904 MT-GLAZE 22K JA 1/16W


R227 401 105 4205 MT-GLAZE 33K JA 1/16W R228 401 025 2305 CARBON 150K JA 1/6W R229 401 105 6506 MT-GLAZE 680 JA 1/16W R230 401 026 9303 CARBON 47 JA 1/6W R234 401 105 5806 MT-GLAZE 56 JA 1/16W R235 401 105 5806 MT-GLAZE 56 JA 1/16W R236 401 105 5806 MT-GLAZE 56 JA 1/16W R237 401 027 8602 CARBON 8.2K JA 1/6W R242 401 105 7909 MT-GLAZE 0.000 ZA 1/16W R243 401 068 3703 OXIDE-MT 470 JA 2W R244 401 105 5400 MT-GLAZE 47K JA 1/16W R245 401 105 5400 MT-GLAZE 47K JA 1/16W R271 401 105 0405 MT-GLAZE 100 JA 1/16W R272 401 105 0405 MT-GLAZE 100 JA 1/16W R280 401 105 0405 MT-GLAZE 100 JA 1/16W R282 401 105 4106 MT-GLAZE 3.3K JA 1/16W R284 401 105 4106 MT-GLAZE 3.3K JA 1/16W R286 401 105 5301 MT-GLAZE 4.7K JA 1/16W R289 401 105 7909 MT-GLAZE 0.000 ZA 1/16W R291 401 068 1600 OXIDE-MT 4.7 JA 2W R350 401 105 0603 MT-GLAZE 10K JA 1/16W R351 401 105 1600 MT-GLAZE 15K JA 1/16W R352 401 012 7009 CARBON 10K JA 1/4W R354 401 025 8208 CARBON 22K JA 1/6W R355 401 012 7009 CARBON 10K JA 1/4W R356 401 105 0603 MT-GLAZE 10K JA 1/16W R357 401 026 7002 CARBON 3.9K JA 1/6W R358 401 105 4700 MT-GLAZE 39K JA 1/16W R359 401 027 9005 CARBON 82K JA 1/6W R3711 401 024 6700 CARBON 100 JA 1/6W R3721 401 024 6700 CARBON 100 JA 1/6W R3731 401 024 6700 CARBON 100 JA 1/6W R3732 401 024 6700 CARBON 100 JA 1/6W R3734 401 025 8208 CARBON 22K JA 1/6W R3735 401 025 8208 CARBON 22K JA 1/6W R3736 401 105 0603 MT-GLAZE 10K JA 1/16W R3737 401 105 0603 MT-GLAZE 10K JA 1/16W R3741 401 105 8203 MT-GLAZE 68K JA 1/16W R3742 401 105 8203 MT-GLAZE 68K JA 1/16W R3743 401 105 8203 MT-GLAZE 68K JA 1/16W R3744 401 105 8203 MT-GLAZE 68K JA 1/16W R3745 401 105 2904 MT-GLAZE 22K JA 1/16W R3746 401 105 2904 MT-GLAZE 22K JA 1/16W R422 401 019 3004 CARBON 39K JA 1/4W R423 401 022 4104 CARBON 68K JA 1/4W R424 401 024 7004 CARBON 1K JA 1/6W R426 401 024 7400 CARBON 10K JA 1/6W R432 401 105 0504 MT-GLAZE 1K JA 1/16W R433 401 007 1104 CARBON 1K JA 1/2W R434 401 009 9306 CARBON 390 JA 1/2W R435 402 080 3702 OXIDE-MT 6.8 JB 7W R441 401 058 3706 OXIDE-MT 1K JA 1W R449 401 105 4601 MT-GLAZE 3.9K JA 1/16W R475 401 009 5803 CARBON 330 JA 1/2W R479 401 105 5301 MT-GLAZE 4.7K JA 1/16W R481 401 067 3100 OXIDE-MT 3.9 JA 2W R484 401 022 4104 CARBON 68K JA 1/4W R485 401 023 3700 CARBON 82K JA 1/4W R486 401 026 9907 CARBON 4.7K JA 1/6W R488 401 142 9508 OXIDE-MT 0.27 JA 1W R501 401 064 8702 OXIDE-MT 1K JA 2W R502 401 069 2804 OXIDE-MT 680 JA 2W R503 401 066 9103 OXIDE-MT 27 JA 2W R510 401 024 7400 CARBON 10K JA 1/6W R511 401 024 7400 CARBON 10K JA 1/6W R512 401 020 0801 CARBON 470 JA 1/4W R514 401 024 9701 CARBON 12K JA 1/6W

R515 401 026 1307 CARBON 27K JA 1/6W R516 401 024 9701 CARBON 12K JA 1/6W R518 401 006 8104 CARBON 1.2 JA 1/2W R519 401 024 6700 CARBON 100 JA 1/6W R522 401 027 5205 CARBON 680 JA 1/6W R525 401 058 8107 OXIDE-MT 120 JA 1W R527 401 105 8104 MT-GLAZE 56K JA 1/16W R601 401 008 8607 CARBON 220K JA 1/2W R602 402 082 5605 WIRE WOUND 1.8 KA 10W

402 074 6108 WIRE WOUND 1.8 KA 10W R611 401 020 0801 CARBON 470 JA 1/4W R613 402 001 6607 FUSIBLE RES 1.2 K J- 1/ R614 401 025 8208 CARBON 22K JA 1/6W R615 401 025 7409 CARBON 220 JA 1/6W R616 401 024 7400 CARBON 10K JA 1/6W R619 401 016 1508 CARBON 22 JA 1/4W R620 401 010 4802 CARBON 470K JA 1/2W R621 401 010 4802 CARBON 470K JA 1/2W R622 401 019 9600 CARBON 47 JA 1/4W R623 401 026 4902 CARBON 330K JA 1/6W R624 402 001 8502 FUSIBLE RES 10 J- 1/2W R625 401 069 4501 OXIDE-MT 68K JA 2W R626 401 069 4501 OXIDE-MT 68K JA 2W R627 401 025 8208 CARBON 22K JA 1/6W R628 402 000 8305 SOLID 5.6M KA 1/2W R629 402 000 8305 SOLID 5.6M KA 1/2W R631 401 026 7408 CARBON 39K JA 1/6W R632 401 064 1406 OXIDE-MT 0.33 JA 2W R634 401 024 7400 CARBON 10K JA 1/6W R635 401 025 8208 CARBON 22K JA 1/6W R636 401 024 7400 CARBON 10K JA 1/6W R637 401 025 8208 CARBON 22K JA 1/6W R638 401 012 5708 CARBON 1K JA 1/4W R641 401 024 7400 CARBON 10K JA 1/6W R642 401 027 0309 CARBON 47K JA 1/6W R643 401 025 4606 CARBON 18K JA 1/6W R644 401 025 8208 CARBON 22K JA 1/6W R651 401 024 7004 CARBON 1K JA 1/6W R652 401 012 7009 CARBON 10K JA 1/4W R654 401 007 2309 CARBON 100K JA 1/2W R655 401 012 7009 CARBON 10K JA 1/4W R656 401 026 3905 CARBON 330 JA 1/6W R657 401 019 1901 CARBON 3.9K JA 1/4W R658 401 012 7009 CARBON 10K JA 1/4W R659 401 019 1901 CARBON 3.9K JA 1/4W R661 401 012 8105 CARBON 100K JA 1/4W R662 401 026 9907 CARBON 4.7K JA 1/6W R663 401 025 2305 CARBON 150K JA 1/6W R664 401 010 4307 CARBON 47K JA 1/2W R665 401 025 8208 CARBON 22K JA 1/6W R666 401 105 2904 MT-GLAZE 22K JA 1/16W R667 401 105 0603 MT-GLAZE 10K JA 1/16W R668 401 069 5607 OXIDE-MT 8.2 JA 2W R669 401 069 0404 OXIDE-MT 6.8 JA 2W R671 401 025 8703 CARBON 220K JA 1/6W R672 401 024 9701 CARBON 12K JA 1/6W R673 401 105 6100 MT-GLAZE 560K JA 1/16W R681 401 025 8208 CARBON 22K JA 1/6W R682 401 105 6100 MT-GLAZE 560K JA 1/16W R694 401 064 6302 OXIDE-MT 10 JA 2W R801 401 105 3505 MT-GLAZE 270K JA 1/16W R811 401 105 3406 MT-GLAZE 27K JA 1/16W R812 401 105 0603 MT-GLAZE 10K JA 1/16W R813 401 105 0603 MT-GLAZE 10K JA 1/16W R814 401 105 0603 MT-GLAZE 10K JA 1/16W R815 401 105 0603 MT-GLAZE 10K JA 1/16W R816 401 105 0603 MT-GLAZE 10K JA 1/16W

!

!

-25-

C2GW


-26-

C2GW

R817 401 024 7004 CARBON 1K JA 1/6W R818 401 024 7004 CARBON 1K JA 1/6W R819 401 105 0603 MT-GLAZE 10K JA 1/16W R830 401 024 7004 CARBON 1K JA 1/6W R831 401 026 9600 CARBON 470 JA 1/6W R833 401 024 7400 CARBON 10K JA 1/6W R834 401 105 0603 MT-GLAZE 10K JA 1/16W R835 401 105 0603 MT-GLAZE 10K JA 1/16W R836 401 105 0603 MT-GLAZE 10K JA 1/16W R837 401 105 1600 MT-GLAZE 15K JA 1/16W R838 401 105 1600 MT-GLAZE 15K JA 1/16W R839 401 105 4007 MT-GLAZE 330 JA 1/16W R840 401 105 4007 MT-GLAZE 330 JA 1/16W R841 401 105 5301 MT-GLAZE 4.7K JA 1/16W R842 401 105 5301 MT-GLAZE 4.7K JA 1/16W R845 401 105 5400 MT-GLAZE 47K JA 1/16W R851 401 024 6700 CARBON 100 JA 1/6W R852 401 024 7400 CARBON 10K JA 1/6W R853 401 027 8602 CARBON 8.2K JA 1/6W R855 401 027 8602 CARBON 8.2K JA 1/6W R857 401 027 8602 CARBON 8.2K JA 1/6W R861 401 105 1501 MT-GLAZE 1.5K JA 1/16W R862 401 105 7404 MT-GLAZE 8.2K JA 1/16W R863 401 105 5400 MT-GLAZE 47K JA 1/16W R866 401 024 6700 CARBON 100 JA 1/6W R869 401 024 6700 CARBON 100 JA 1/6W R870 401 105 2904 MT-GLAZE 22K JA 1/16W R871 401 105 0603 MT-GLAZE 10K JA 1/16W R872 401 026 1307 CARBON 27K JA 1/6W R873 401 105 4205 MT-GLAZE 33K JA 1/16W R874 401 105 0603 MT-GLAZE 10K JA 1/16W R875 401 105 0603 MT-GLAZE 10K JA 1/16W R876 401 105 5400 MT-GLAZE 47K JA 1/16W R877 403 157 7203 CERAMIC 3900P K 50V R878 401 105 6001 MT-GLAZE 5.6K JA 1/16W R881 401 105 4106 MT-GLAZE 3.3K JA 1/16W R882 401 105 4106 MT-GLAZE 3.3K JA 1/16W R883 401 105 4205 MT-GLAZE 33K JA 1/16W R886 401 025 8208 CARBON 22K JA 1/6W R887 401 105 2904 MT-GLAZE 22K JA 1/16W R888 401 027 2303 CARBON 560 JA 1/6W R892 401 105 5509 MT-GLAZE 470K JA 1/16W R893 401 105 8005 MT-GLAZE 1M JA 1/16W R894 401 024 6700 CARBON 100 JA 1/6W

VARIABLE RESISTORVR651 645 006 5514 VR,SEMI,2.2K N

645 003 5579 VR,SEMI,2.2K N

TRANSFORMERT431 610 000 1053 DRIVE TRANS

610 000 1060 DRIVE TRANS 610 223 1649 DRIVE TRANS 645 047 3326 TRANS,DRIVE

T471 645 057 2258 TRANS, FLYBACK T611 645 057 0865 TRANS,POWER,PULSE 21 SING

COILL1501 645 018 9722 CORE,PIPE L171 645 049 3379 TRANS,OSC,38MHZ

645 054 0271 TRANS,OSC,38MHZ L3701 645 008 2894 INDUCTOR,5.6U K L431 610 031 9998 PIPE CORE

645 018 7025 CORE,PIPE L432 610 031 9998 PIPE CORE

645 018 7025 CORE,PIPE L441 645 015 9312 COIL,LINEARITY

L601 645 019 3873 LINE FILTER 652 000 1961 LINE FILTER

L616 645 005 0763 CORE,PIPE L801 645 008 2894 INDUCTOR,5.6U K

DIODED001 407 149 0807 DIODE 1SS355-TE-17 D005 407 149 0807 DIODE 1SS355-TE-17 D006 407 099 6102 ZENER DIODE MTZJ10B

407 054 0008 ZENER DIODE RD10EB2 D1002 407 063 8309 ZENER DIODE MTZJ11C

407 054 1807 ZENER DIODE RD11EB3 D1003 407 005 4505 DIODE DS442X

408 008 2406 DIODE 1N4148 407 012 4406 DIODE 1SS133 407 013 4306 DIODE 1S2076A 407 013 7109 DIODE 1S2473

D1004 407 005 4505 DIODE DS442X 408 008 2406 DIODE 1N4148 407 012 4406 DIODE 1SS133 407 013 4306 DIODE 1S2076A 407 013 7109 DIODE 1S2473

D1005 407 005 4505 DIODE DS442X 408 008 2406 DIODE 1N4148 407 012 4406 DIODE 1SS133 407 013 4306 DIODE 1S2076A 407 013 7109 DIODE 1S2473

D103 407 100 0204 ZENER DIODE MTZJ36A 407 056 2307 ZENER DIODE RD36EB1

D1030 407 071 0005 ZENER DIODE DZD12X-TA 407 071 0104 ZENER DIODE DZD12Y-TA 407 071 0203 ZENER DIODE DZD12Z-TA 407 199 6200 ZD 02CZ12X(TE85R) 407 175 2806 ZD 02CZ12Y(TE85R) 407 175 2905 ZD 02CZ12Z(TE85R)




D122 401 105 7909 MT-GLAZE 0.000 ZA 1/16W D1401 408 008 2406 DIODE 1N4148

407 012 4406 DIODE 1SS133 407 013 4306 DIODE 1S2076A 407 013 7109 DIODE 1S2473

D1402 408 008 2406 DIODE 1N4148 407 012 4406 DIODE 1SS133 407 013 4306 DIODE 1S2076A 407 013 7109 DIODE 1S2473

D1902 407 149 0807 DIODE 1SS355-TE-17 D1903 407 005 4505 DIODE DS442X

408 008 2406 DIODE 1N4148 407 012 4406 DIODE 1SS133

!

!

!


407 013 4306 DIODE 1S2076A 407 013 7109 DIODE 1S2473

D1910 407 158 9204 LED SPR-39MVWF D1910A 610 273 7929 HOLDER LED-S4KF D249 407 099 6003 ZENER DIODE MTZJ9.1B

407 057 9701 ZENER DIODE RD9.1EB2 D350 407 149 0807 DIODE 1SS355-TE-17 D351 407 149 0807 DIODE 1SS355-TE-17 D352 407 056 8002 ZENER DIODE RD5.1EB2 D357 407 149 0807 DIODE 1SS355-TE-17 D3701 408 008 2406 DIODE 1N4148


D421 407 099 7208 ZENER DIODE MTZJ16A 407 099 7406 ZENER DIODE MTZJ16C 407 054 7007 ZENER DIODE RD16EB1 407 054 7205 ZENER DIODE RD16EB3

D441 407 006 6300 DIODE ERC05-10B 407 009 6901 DIODE RM11C

D448 407 063 8705 ZENER DIODE MTZJ5.1C 407 056 9801 ZENER DIODE RD5.6EB1

D467 408 008 2406 DIODE 1N4148 407 013 4306 DIODE 1S2076A 407 013 6508 DIODE 1S2471

D468 408 008 2406 DIODE 1N4148 407 012 4406 DIODE 1SS133 407 013 4306 DIODE 1S2076A 407 013 7109 DIODE 1S2473

D476 407 063 8408 ZENER DIODE MTZJ12C T-72 407 054 3306 ZENER DIODE RD12EB3

D485 407 007 7405 DIODE EU1 D486 408 008 2406 DIODE 1N4148


D501 407 005 7308 DIODE EM01Z 407 005 8602 DIODE ERA15-02 408 009 9008 DIODE BYD33D

D512 407 005 7308 DIODE EM01Z 407 005 8602 DIODE ERA15-02 408 009 9008 DIODE BYD33D





D610 407 104 2402 PHOTO COUPLE PC817C 407 106 6101 PHOTO COUPLE PC817D

D611 407 146 8103 DIODE EG01C D612 407 005 9807 DIODE ERA81-004 D614 407 007 6606 DIODE ES1 D615 407 012 4406 DIODE 1SS133 D616 407 055 1806 ZENER DIODE RD20EB2 D617 407 012 4406 DIODE 1SS133 D619 407 063 9306 ZENER DIODE MTZJ7.5C

407 057 6502 ZENER DIODE RD7.5EB3 D622 407 012 4406 DIODE 1SS133 D623 407 099 6607 ZENER DIODE MTZJ-T-7212B

407 054 3207 ZENER DIODE RD12EB2-T4 D643 407 012 4406 DIODE 1SS133 D651 407 156 2207 DIODE RU4B LF-L1 D652 407 210 5700 DIODE RN1Z D653 407 211 6102 DIODE FE301-1L43

407 129 6706 DIODE RU4YX LF-L1 D654 407 166 2303 DIODE ERC91-02 D655 407 012 4406 DIODE 1SS133 D659 407 012 4406 DIODE 1SS133 D661 407 099 5600 ZENER DIODE MTZJ6.8A D662 407 099 5600 ZENER DIODE MTZJ6.8A D664 407 099 6102 ZENER DIODE MTZJ10B D671 408 008 2406 DIODE 1N4148


D861 407 055 7907 ZENER DIODE RD3.6EL 408 041 2005 ZENER DIODE RD3.6EL

MISCELLANEOUSF601 423 024 8409 FUSE 250V 4A F601A 645 040 3576 HOLDER,FUSE F601B 645 040 3576 HOLDER,FUSE A101 645 051 8423 TUNER,U/V A1901 645 041 1519 UNIT,REMOCON RECEIVER

645 044 0519 UNIT,REMOCON RECEIVER K001 645 006 4708 JACK,PHONE D3.6

652 000 0155 JACK,PHONE D3.5 K1001 645 056 0354 JACK,RCA-3 K1002 645 033 2708 JACK,RCA-6 K1004 645 007 1584 SOCKET,DIN 4P PS601 408 024 1605 THERMISTOR PTH451C462BD14

408 043 8104 THERMISTOR PTH451C140Q21 408 000 4309 TH PTH451C312BD140N290

SW1901 645 003 4701 SWITCH,PUSH 1P-1TX1 645 019 4887 SWITCH,PUSH 1P-1TX1 645 027 7382 SWITCH,PUSH 1P-1TX1






SW501 610 011 2728 SWITCH,LEVER 1P-3T 652 000 0049 SWITCH,LEVER

SW601 645 050 4129 SWITCH,PUSH POWER 2P-2T 645 053 4904 SWITCH, PUSH POWER 2P-2T

VA601 407 130 2902 VARISTOR ENC471D-14A 407 171 2008 VARISTOR ERZV14D471

X161 421 009 4606 SAW F TSF5419P X211 645 024 8818 OSC,CRYSTAL 4.433619MHZ X801 645 004 1938 OSC,CRYSTAL 32.768KHZ

645 004 1945 OSC,CRYSTAL 32.768KHZ

610 304 8994 ASSY,PWB,CRT C2GW1AA0B10S1000B

TRANSISTORQ721 406 000 6804 TR 2SA1015-G(SAN)-TPE2

405 001 7407 TR 2SA1015-O(SAN) 405 001 7605 TR 2SA1015-Y(SAN) 405 004 3109 TR 2SA564A-Q(CU)

!

!

!

!

!

-27-

C2GW


405 004 3208 TR 2SA564A-R(CU) 405 151 3304 TR 2SA608NF-NPA 405 006 1707 TR 2SA933S-Q 405 006 1806 TR 2SA933S-R

INTEGRATED CIRCUITIC701 409 468 8403 IC TDA6103Q/N3

CAPACITORC701 403 012 4002 CERAMIC 15P J 50V C702 403 012 4002 CERAMIC 15P J 50V C703 403 032 7403 CERAMIC 8P D 50V C711 403 067 5603 MT-COMPO 0.1U J 50V

403 237 8007 MT-COMPO 0.1U J 50V C712 403 067 6709 MT-COMPO 0.22U J 50V

403 237 7901 MT-COMPO 0.22U J 50V C718 403 077 2708 CERAMIC 1000P P 2K

403 077 2807 CERAMIC 1000P Z 2K 403 312 8304 CERAMIC 1000P Z 2K

C721 403 208 6308 ELECT 220U M 16V C722 403 281 1108 ELECT 22U M 250V

403 260 0405 ELECT 22U M 250V

RESISTORR701 401 025 1605 CARBON 1.5K JA 1/6W R702 401 025 1605 CARBON 1.5K JA 1/6W R703 401 025 1605 CARBON 1.5K JA 1/6W R704 401 065 0804 OXIDE-MT 100K JA 2W R705 401 065 0804 OXIDE-MT 100K JA 2W R706 401 065 0804 OXIDE-MT 100K JA 2W R707 401 024 9305 CARBON 1.2K JA 1/6W R708 401 024 9305 CARBON 1.2K JA 1/6W R709 401 024 9305 CARBON 1.2K JA 1/6W R711 401 016 5803 CARBON 220K JA 1/4W R712 401 016 3809 CARBON 2.2K JA 1/4W R713 401 007 8400 CARBON 1.5K JA 1/2W R714 401 007 8400 CARBON 1.5K JA 1/2W

R715 401 007 8400 CARBON 1.5K JA 1/2W R718 401 007 8400 CARBON 1.5K JA 1/2W R721 401 012 7009 CARBON 10K JA 1/4W R722 401 012 7009 CARBON 10K JA 1/4W

COILL721 401 019 9600 CARBON 47 JA 1/4W

DIODED701 407 005 4505 DIODE DS442X

408 008 2406 DIODE 1N4148 407 013 1206 DIODE 1S1555 407 013 4207 DIODE 1S2076 407 013 7109 DIODE 1S2473

D702 407 005 4505 DIODE DS442X 408 008 2406 DIODE 1N4148 407 013 1206 DIODE 1S1555 407 013 4207 DIODE 1S2076 407 013 7109 DIODE 1S2473



MISCELLANEOUSK701 645 040 0056 SOCKET,CRT 9P !


SANYO Electric Co., Ltd.A14800 /Nov. /’02 /30 BB

Printed in Japan

SERVICE MANUAL Colour Television Model No....

Documents

Transcript of SERVICE MANUAL Colour Television Model No....