Tumo-Int3BladesWindTurbineTowerMakingandInstallationGuide · 2017. 8. 22. ·...

6
Tumo-Int 3 Blades Wind Turbine Tower Making and Installation Guide Tower Making Tower diameter for 400W 3 blades wind turbine should at least Φ60mm, thickness 3mm. Tower diameter for 600W and 1000W 3 blades wind turbine should at least Φ76mm, thickness 3.5 mm. Tower height can be 6~12meters. Technical requirement 1、L-type bolts for four galvanized wire strands; screws should be 60 higher from the mixed earth surface. 2、C25 motar can be used for mixed earth. mixed earth mounds Figure1:manufacture of mixed earth mound Figure2 The manufacture of earth anchor(3 sets) U-type bolt(4-WIRE STRAND) Galvanized steel guy wire Strainer(16 inches) The earth anchor Wind turbine tower GB/T5976-8 1*19-10 3、The metal parts should be under the threatment of anticorrosion and rust proofing. Figure3 The manufacture of guy cable

Transcript of Tumo-Int3BladesWindTurbineTowerMakingandInstallationGuide · 2017. 8. 22. ·...

Page 1: Tumo-Int3BladesWindTurbineTowerMakingandInstallationGuide · 2017. 8. 22. · Tumo-Int3BladesWindTurbineTowerMakingandInstallationGuide TowerMaking • Tower diameter for 400W 3 blades

Tumo-Int 3 Blades Wind Turbine Tower Making and Installation GuideTower Making

• Tower diameter for 400W 3 blades wind turbine should at least Φ60mm, thickness 3mm.

• Tower diameter for 600W and 1000W 3 blades wind turbine should at least Φ76mm, thickness 3.5 mm.

• Tower height can be 6~12meters.

Technical requirement1、L-type bolts for four galvanized wire strands;

screws should be 60 higher from the mixed earth surface.

2、C25 motar can be used for mixed earth.

mixed earth mounds

Figure1:manufacture of mixed earth mound

Figure2

The manufacture of earth anchor(3 sets)

U-type bolt(4-WIRE STRAND)

Galvanized steel guy wire

Strainer(16 inches)

The earth anchor

Wind turbine tower

GB/T5976-8

1*19-10

3、The metal parts should be under the threatment of anticorrosion and rust proofing.

Figure3The manufacture of guy cable

Page 2: Tumo-Int3BladesWindTurbineTowerMakingandInstallationGuide · 2017. 8. 22. · Tumo-Int3BladesWindTurbineTowerMakingandInstallationGuide TowerMaking • Tower diameter for 400W 3 blades

Tumo-Int 3 Blades Wind Turbine Tower Making and Installation Guide• Making the upper tower with flange: solid welding, no leak at the weld zone; the earth lug must be welded 20cm away from the ground(clearlyvisible). It will be connected to the lightening grounding device.

stiffener

Tron pipe

Flange base

Tron pipe

stiffener

The flange joint

decided on your own

steel bracket

Flange base

welded

tinned

Grounding connector

tinned

Rubber Cushion

Be

ugl

Tower base

outlet

Page 3: Tumo-Int3BladesWindTurbineTowerMakingandInstallationGuide · 2017. 8. 22. · Tumo-Int3BladesWindTurbineTowerMakingandInstallationGuide TowerMaking • Tower diameter for 400W 3 blades

Tumo-Int 3 Blades Wind Turbine Tower Making and Installation Guide• Lightning protection must be prepared before setting up the wind turbine.

Page 4: Tumo-Int3BladesWindTurbineTowerMakingandInstallationGuide · 2017. 8. 22. · Tumo-Int3BladesWindTurbineTowerMakingandInstallationGuide TowerMaking • Tower diameter for 400W 3 blades

Tumo-Int 3 Blades Wind Turbine Tower Making and Installation GuideTower Installation

• The minimum recommended tower height is 20 ft (6 m) on open ground or 20 ft (6 m) above nearby obstructions (refer to following figure).

•Try to locate the wind turbine in the “cleanest” turbulent free air as possible. Turbulence will reduce the efficiency of wind turbine and may acceleratewear on rotating components.

• Try to locate the turbine without obstacles within 200m of installation center.

• The installation distance between two turbines should be 8-10 times of the rotor diameter.

• Installation site should be complied with local regulations.

Page 5: Tumo-Int3BladesWindTurbineTowerMakingandInstallationGuide · 2017. 8. 22. · Tumo-Int3BladesWindTurbineTowerMakingandInstallationGuide TowerMaking • Tower diameter for 400W 3 blades

Flenge for 3 blades wind turbine (1000W)

Tower

Page 6: Tumo-Int3BladesWindTurbineTowerMakingandInstallationGuide · 2017. 8. 22. · Tumo-Int3BladesWindTurbineTowerMakingandInstallationGuide TowerMaking • Tower diameter for 400W 3 blades