Spec No.

Description： RJ45 Tab up over USB 2.0 stack

UDE P/N： RU9-26MA5WJQ

Checked Prepared

LED:L-Green/Orange; R-Yellow

10/100/1000 Base-T

Contact Area : 30μ" Gold

Approved

To：

Surge Protection

Through Hole

Customer P/N：

2014/8/28 B

Update Date Revision

RU914009-FX

Spec No. : RU914009-FX RU9-26MA5WJQ

1. MECHANICAL DIMENSION

1.1 Product Dimension

www.ude-corp.com

± 0.25

± 0.13

± 0.08

General Tolerance :

X.X :

X.XX :

X.XXX :

- 1 -

Spec No. : RU914009-FX RU9-26MA5WJQ

1.2 Recommended PCB Layout

Component Side of Board

All dimension tolerance are ±0.05mm unless otherwise specified

www.ude-corp.com- 2 -

Spec No. : RU914009-FX RU9-26MA5WJQ

1.3

- All dimensions follow :

FCC subpart F, 68,500, Figure (C)(2)(i) & (C)(2)(ii) & (C)(3)(i)

IEC 60603-7

- All plugs must be meeting the requirements of plug Go & No-Go gauge.

Gauge follow : FCC subpart F, 68,500, Figure (C)(4)(i) & (C)(5)(i)

- There must be no damage to Housing and Locking Latch.

- There must be no nicks and cuts in cable.

- Durability : 750 cycles generally

www.ude-corp.com- 3 -

Standard RJ45 Plug Specification

Spec No. : RU914009-FX RU9-26MA5WJQ

1.4

- All dimensions follow : Universal Series Bus Specification 2.0 (April 27,2000)

Figure 6-9. USB Series A Plug Interface Drawing

www.ude-corp.com

Standard USB 2.0 Plug Specification

- 4 -

Spec No. : RU914009-FX RU9-26MA5WJQ

2. REQUIREMENTS

2.1 Design and Construction

2.2 Material

2.2.1 Terminal Parts (Underplating : 50μ" min Nickel overall)

2.2.1.1 RJ Terminal : PH. Bronze(C5191R-H), Thickness=0.30mm

Finish : Contact Area : 30μ" Gold

2.2.1.2 USB Terminal : PH. Bronze(C5191R-H), Thickness=0.25mm

Finish : Contact Area : 30μ" Gold

Solder Tail : 100μ" min. Tin

2.2.1.3 Input Terminal : Brass(C2680R-EH), Thickness=0.35mm

Finish : 100μ" min. Tin

2.2.1.4 Case Terminal : Brass(C2680R-EH), Thickness=0.35mm

Finish : 100μ" min. Tin

2.2.2 Plastic Parts <UL94V-0>

2.2.2.1 Housing : PBT, Black

2.2.2.2 Case : PBT, Black

2.2.2.3 Spacer : PBT, Black

2.2.2.4 Cover : PBT, Black

2.2.3 Shield Parts

2.2.3.1 Front Shield : Stainless(SUS304R-1/2H), Thickness=0.25mm, unplating

2.2.3.2 Back Shield : Stainless(SUS304R-1/2H),Thickness=0.20mm, Pre-soldering

2.2.3.3 USB Kink : Brass(C2680R-H), Thickness=0.25mm

Finish : 100μ" min. Mt. Tin over 30μ" min. Nickel overall

www.ude-corp.com

Product shall be of design, construction and physical dimensions specified

on applicable.

- 5 -

Spec No. : RU914009-FX RU9-26MA5WJQ

2.3 Operating and Storage Temperature

2.4 RJ45 specifications

2.5 USB 2.0 specifications

500Vac @1min

2.6 Performance and Test Description

2.7 Packaging and Packing

www.ude-corp.com

1500 cycles

Insertion force :

- 6 -

Insulation Resistance :

Durability :

10N min

Dielectric Withstanding Voltage :

50N min. @ 60+/-5 sec

All parts shall be packaged and packed to protect against physical

damage、corrosion and deterioration during shipment and storage.

Removal force :

Insertion force with the latch depressed :

44N max

Product is designed to meet electrical, mechanical and environmental

performance requirements specified in below table. All tests are performed

at ambient environmental conditions per MIL-STD-1344A and EIA-364

unless otherwise specified.

Locking Force of Plug Latch :

22N max

1000MΩ min.

0°C to +70°C

-40°C to +85°C

Removal force with the latch depressed :

Durability :

Insulation Resistance :500MΩ min.

Operating Temperature :

Storage Temperature :

2500 cycles

35N max

Spec No. : RU914009-FX RU9-26MA5WJQ

3. ELECTRICAL CHARACTERISTICS

3.1 Schematic

www.ude-corp.com

Yellow 585

Emitting Color

10μA max.

- 7 -

10μA max.

610 1.7 ~2.6 VOrange

1.7 ~2.6 V

λp (nm) Vf @If=20mA Ir @Vr=5V

10μA max.1.7 ~2.6 V

565Green

Orange Green

L3

L4

L1

L2

Yellow

RC termination TSS

VCC R1

TD1+ R2

TD2+ R4

TD2- R5

TD3- R7

TD1- R3

TD4+ R8

TD3+ R6

TD4- R9

GND R10

C1 TX1+

C2 TX1-

C3 TX2+

C6 TX2-

C4 TX3+

C5 TX3-

C7 TX4+

C8 TX4-

INPUT RJ45 OUTPUT

0.1uF

0.1uF

0.1uF

0.1uF

T1

T1

T1

T1

Shield

Spec No. : RU914009-FX RU9-26MA5WJQ

3.2 Transmitter filter & Receiver filter

Type : Balance low pass 100Ω impedance

Insertion loss :

Return loss :

3.3 Common Mode Rejection

@ 1~100 MHz -30dB min.

3.4 Cross Talk

@ 1~100 MHz -30dB min.

3.5 Inductance @ 100KHz, 0.1V, 8mA DC BIAS

Input (R2-R3), Input(R4-R5), Input (R6-R7), Input(R8-R9): 350 μH min.

3.6 HiPot Test

Input(R2-R3) To 1500Vac 60s or 2250Vdc 60s

Input(R4-R5) To 1500Vac 60s or 2250Vdc 60s

Input(R6-R7) To 1500Vac 60s or 2250Vdc 60s

Input(R8-R9) To 1500Vac 60s or 2250Vdc 60s

3.7 ESD protection

IEC 61000-4-2 (ESD) 15KV (Air), 8KV (Contact)

3.8 Surge protection

IEC 61000-4-5 (Lightning) (10/700 uS)

www.ude-corp.com

Line to GND：+/-5.5KV

load 100Ω

-1.0dB max.

1~30 MHz

Output(C1-C2) :

-12dB min.

30~60MHz

- 8 -

1~100 MHz

load 100Ω

80~100MHz

load 100Ω

-16dB min.

60~80MHz

-10dB min. load 100Ω

-18dB min.

Output(C3-C6) :

Output(C4-C5) :

Output(C7-C8) :

Spec No. : RU914009-FX RU9-26MA5WJQ

4. ORDER INFORMATION

R U 9 - 2 6 MA Q

A B D

A. LED Code :

B. Mechanical Code :

C. Schematics Code :

D. Plating Code :

A : 1 :

C : 6 :

B : 2 :

D : 3 :

Q: 4 :

G : 9 :

www.ude-corp.com

5WJ : 5WJ circuit

- 9 -

100μ " min. Bright Tin 100μ " min. Matted Tin

50μ " gold

Underplating

C

L-Green/Orange; R-Yellow. <Refer to Schematic of LED>

5WJ

w/ UDE Logo, w/o spring

30μ " gold

6μ " gold

30μ " gold

50μ " min Nickel overall

Gold Flash

Contact Area

50μ " gold

30μ " gold

6μ " gold

15μ " gold

Gold Flash

Solder Tail

10μ " gold

15μ " gold

Spec No. : RU914009-FX RU9-26MA5WJQ

5. DIPPING TEMPERATURE PROFILE

www.ude-corp.com- 10 -

Spec No. : RU914009-FX RU9-26MA5WJQ

6. Revision History

www.ude-corp.com

Issue Date Revision Comments Operator

2014/8/27 A Initial Release . Sophia

2014/8/28 B Update Electrical Characteristics

- 11 -

Rock