Powder Transfer Diaphragm Pumps · 2018. 4. 7. · Talc Toners And many more... The performance...
2
www.yamadacorp.co.jp/global Powder Transfer Diaphragm Pumps The Yamada Powder Transfer Pumps were specifically designed to move bulk solids more effectively throughout your process. They are a cost effective replacement for Augers and Conveyors and eliminate unsafe and labor intensive means of moving bulk powders. These heavy duty pumps consistently transfer fine-grained (100μm or finer), low bulk density (5 to 10 lbs. / cubit foot or 0.07 to 0.16kg/litter), dry powders in a dust-free operation. Yamada offers a base unit specifically for light powders, which include the following standard features. ● Conveying distance depends upon the micron size and the bulk density of the powder. For example fumed silica can be conveyed 150 feet(4.5M) while flour a maximum of 40 feet(12M). Refer to the Yamada “Pumpable Powders” data sheet for specific materials. ● Powder must be 150 mesh(106 micron)or smaller size particle / powder and dry. The Pump will not pump crystals or flakes and the bulk density should be less than 50lbs/cubic feet, The higher the bulk density, the shorter the conveying distance and the lower the flow rate. ● The Pump can be located a maximum of 15feet(4.5M) above powder source. ● PTFE check balls are recommend for sticky powders. - Apparent specific gravity is 0.5 or less - Repose angle is 30 degree or less - Powder must be completely dry - Powder must have large fluidity ● Yamada recommends regulating compressed air to 70PSI(0.5MPa) M a x i m u m . ● Yamada recommends aeration / fluidization of the powder a minimum of 10 to 15 seconds prior to starting the pump- premature diaphragm, center shaft, and center disk failure can be avoided. Applications Activated Carbon Acrylic Resins Aluminum Oxide Bentonite Carbon Black Cereal Flours Clay Powder Diatomaceous Earth Expanded Mica Fire - extinguishing Powder Fumed Silica Ground Limestone Kaolin Micro Dolomite Filter Dust Pearlite Pesticides Pharmaceuticals Pigments Powder Coatings Powdered Plastics Powdered Rock Quartz Powder Salicylic Acid Silicones Starch Talc Toners And many more... The performance data for powder transfer is highly dependent upon the material being pumped and the application. A trial of the pump in the actual use environment is recommended to verify the actual performance capabilities for any given material. REMARK Condition of powder
Transcript of Powder Transfer Diaphragm Pumps · 2018. 4. 7. · Talc Toners And many more... The performance...
www.yamadacorp.co.jp/global
Powder Transfer Diaphragm PumpsThe Yamada Powder Transfer Pumps were speci�cally designed to move bulk solids more e�ectively throughout your process.They are a cost e�ective replacement for Augers and Conveyors and eliminate unsafe and labor intensive means of moving bulk powders.These heavy duty pumps consistently transfer�ne-grained (100μm or �ner), low bulk density(5 to 10 lbs. / cubit foot or 0.07 to 0.16kg/litter),dry powders in a dust-free operation.Yamada o�ers a base unit speci�cally for lightpowders, which include the followingstandard features.
● Conveying distance depends upon the micron size and the bulk density of the powder. For example fumed silica can be conveyed 150 feet(4.5M) while �our a maximum of 40 feet(12M). Refer to the Yamada “Pumpable Powders” data sheet for speci�c materials.● Powder must be 150 mesh(106 micron)or smaller size particle / powder and dry. The Pump will not pump crystals or �akes and the bulk density should be less than 50lbs/cubic feet, The higher the bulk density, the shorter the conveying distance and the lower the �ow rate.● The Pump can be located a maximum of 15feet(4.5M) above powder source.
● PTFE check balls are recommend for sticky powders.
- Apparent speci�c gravity is 0.5 or less
- Repose angle is 30 degree or less
- Powder must be completely dry
- Powder must have large �uidity
● Yamada recommends regulating compressed air to 70PSI(0.5MPa) M a x i m u m .
● Yamada recommends aeration / �uidization of the powder a minimum of 10 to 15 seconds prior to starting the pump- premature diaphragm, center shaft, and center disk failure can be avoided.
Applications
Activated Carbon Acrylic Resins
Aluminum Oxide Bentonite
Carbon Black Cereal Flours Clay Powder
Diatomaceous Earth Expanded Mica
Fire - extinguishing Powder
Fumed Silica Ground Limestone
Kaolin Micro Dolomite Filter
Dust Pearlite
Pesticides Pharmaceuticals
Pigments Powder Coatings
Powdered Plastics Powdered Rock Quartz Powder
Salicylic Acid Silicones Starch
Talc Toners
And many more...
The performance data for powder transfer is highly dependent upon the material being pumped and the application. A trial of the pumpin the actual use environment is recommended to verify the actual performance capabilities forany given material.
REMARKCondition of powder
Powder Transfer Diaphragm Pumps
International DepartmentNo.1-3, 1-Chome, Minami-Magome, Ohta-ku,Tokyo 143-8504, Japan
Phone +81-(0)3-3777-0241 Fax +81-(0)3-3777-0584
E-mail: [email protected]: www.yamadacorp.co.jp/global
Your Local Distributor:
Form no.:910-501E Revised: Mar.2015
Model BAC1”(25A)
BANNDP-25
Rc1
Rc3/8Rc3/4
ADC12
CR
SMS1025 SUS316SUS316
Approx 200kg/h1600L/min(ANR)3mm or smaller
97dB13kg 20kg
CRNBR NBR
ADC12
SCS14
BSC BSN BAC1-1/2”(25A)BANNDP-40
JIS 10K40A
Rc1/2Rc3/4
ADC12,AC4C-T6
CR
SUS316A5056
Approx 500kg/h4000L/min(ANR)7mm or smaller
95dB29kg 40kg
CRNBR NBR
CR CRNBR NBR
ADC12
SCS14
BSC BSN BAC2”(50A)
BANNDP-50
JIS 10K50A
Rc3/4Rc1
ADC12,AC4C-T6
CR
SUS316A50560.2-0.7 MPa
0.7 MPa
0.7 MPa
Approx 1000kg/h6000L/min(ANR)10mm or smaller
94dB37kg 60kg
CRNBR NBR
CR CRNBR NBR
ADC12
SCS14
BSC BAC3”(50A)
BANNDP-80
JIS 10K80A
Rc3/4Rc1
ADC12,AC4C-T6
CR
SUS316A5056
Approx 1000kg/h6000L/min(ANR)10mm or smaller
92dB65kg 102kg
CRNBR
CR CRNBR
NBR
NBR
ADC12
SCS14
BSCBSN BSN
Connection to liquid
Air connection
Material
Air supply pressure rangeMax discharge pressureMax discharge volumeMax air consumptionMax slurry diamaeterAmbient temp rangeNoise levelWeight
Inlet
InletOutlet
Outlet
Wetted body
Non wetted body
Diaphragm, Ball
Ball seatCenter disk
Nominal port size
NDP-25 NDP-40
NDP-50 NDP-80
642712
403
200250
96
108
(142)
108
(305)(147)
(570)266
4-Ø10
294
Rc 4/3
Rc 2/1
EXHAUST
JIS 10K 40ADN 40 PN 10
LIQUID INLETEQUIVALENT TO
LIQUID OUTLET
JIS 10K 40ADN 40 PN 10EQUIVALENT TO
AIR INLET
288
355
704782
433
250300
106
116
116168
6304-Ø10
324
DIN 50 PN 10ANSI 150 2″
JIS 10K 50A
EQUIVALENT TOOUTLET
AIR INLET
JIS 10K 50A DIN 50 PN 10 ANSI 150 2″EQUIVALENT TOINLET
EXHAUSTRc1
43/Rc
4-Ø10(704)
364
416
128
1001
906
300350
137
433
137(168) 363
DIN 80 PN 10 ANSI 150 3″ JIS 10K 80A
INLETEQUIVALENT TO
EXHAUSTRc1
AIR INLET
DIN 80 PN 10ANSI 150 3″JIS 10K 80A
OUTLETEQUIVALENT TO
43/Rc
Speci�cations
Dimensions
/3Rc 4
Rc /3 8
(252)
49343 382
(395)(143)
196
30
210170
186
30
(414)
287222
129
137
89279
4-Ø9EXHAUST
Rc1
LIQUID INLETRc1
LIQUID OUTLET
AIR INLET
