ORDER DCS - SEP2005 - 004 - MS Service Manualdiagramas.diagramasde.com/otros/PANASONIC...

of 31 /31
Service Manual ORDER DCS - SEP2005 - 004 - MS TC-20KL05P Chassis GP31 TELEVISION Power souce Consumption Antenna imput Color sytem Tuning system Channel capability Picture tube Imput Imput jack AV Terminals Dimension (WxHxD) Weigth Specifications TC-20KL05P 127V / 220V AC, 60Hz automatic switch 61W 75Ω - VHF/UHF/CATV PAL-M / NTSC / PAL-N (FST) VHF: 2 ~13 UHF: 14 ~ 69 CATV: 1 ~ 125 PANABLACK 20” CRT, 51cm (NBR5258) 48cm Measured diagonally 3 W max (PMPO) 1 (rear) 514 x 468x 461mm 17,0 Kg Color Television REMOTE CONTROL TRANSMITER: Model: TNQ2B2801-1 Power source: 3V (2 AA type batteries) Infrared wave lenght 9500 Å (Angstron) Supplied accessories: • 1 remote control transmitter • 1 Balum 300 ohms / 75 ohms • 2 “AA” (or R6) batteries (1.5 V; ABNT/IEC) • 1 antenna © 2005 Panasonic da Amazônia S/A. CS Division Technical Support Specifications are subject to change without prior notice or obligation.

Transcript of ORDER DCS - SEP2005 - 004 - MS Service Manualdiagramas.diagramasde.com/otros/PANASONIC...

Service ManualORDER DCS - SEP2005 - 004 - MS

TC-20KL05PChassis GP31

TELEVISION

Power souce

Consumption

Antenna imput

Color sytem

Tuning system

Channel capability

Picture tubeImput

Imput jack

AV Terminals

Dimension (WxHxD)

Weigth

Specifications

TC-20KL05P

127V / 220V AC, 60Hzautomatic switch

61W

75Ω - VHF/UHF/CATV

PAL-M / NTSC / PAL-N

(FST)

VHF: 2 ~13UHF: 14 ~ 69CATV: 1 ~ 125

PANABLACK20” CRT, 51cm (NBR5258)48cm Measured diagonally

3 W max (PMPO)

1 (rear)

514 x 468x 461mm

17,0 Kg

Color Television

REMOTE CONTROL TRANSMITER:Model: TNQ2B2801-1Power source: 3V (2 AA type batteries)Infrared wave lenght 9500 Å (Angstron)

Supplied accessories:• 1 remote control transmitter• 1 Balum 300 ohms / 75 ohms• 2 “AA” (or R6) batteries (1.5 V; ABNT/IEC)• 1 antenna

© 2005 Panasonic da Amazônia S/A.CS DivisionTechnical Support

Specifications are subject to change without prior notice or obligation.

- 2 -

TC-20KL05P

Contents

Important Safety NoticeSpecial components are used in this television set which are important for safety. These parts are identified on the schematicdiagram by the symbol . It is essential that these critical parts are replaced with the manufacturer’s specified replacementparts to prevent X-ray radiation, shock, fire or other hazards. Do not modify the original design without manufacturer’s permission.

!

General Guidelines

An Isolation Transformer should always be used during the servicing

of a receiver whose chassis is not isolated from the AC power line.

Use a transformer of adequate power rating as this protects the

technician from accidents resulting in personal injury from electrical

shocks. It will also protect the Receiver from being damaged by

accidental shorting that may occur during servicing.

When servicing, observe the original lead dress, especially in the high

voltage circuit. Replace all damaged parts (also parts that show signs

of overheating.)

Always Replace Protective Devices, such as fishpaper, isolation

resistors and capacitors, and shields after servicing the Receiver.

Use only manufacturer’s recommended rating for fuses, circuit

breakers, etc.

High potentials are present when this Receiver is operating. Operation

of the Receiver without the rear cover introduces danger from electrical

shock. Servicing should not be performed by anyone who is not

thoroughly familiar with the necessary precautions when servicing

high-voltage equipment.

Extreme care should be practiced when Handling the Picture Tube.

Rough handling may cause it to implode due to atmospheric pressure

(14.7 lbs per sq. in). Do not sick or scratch the glass or subject it to

any undue pressure. When handling, use safety goggles and heavy

gloves for protection. Discharge the picture tube by shorting the anode

to chassis ground (not to the cabinet or to other mounting hardware).

When discharging, connect cold ground (i.e. dag ground lead) to the

anode with a well insulated wire or use a grounding probe.

Avoid prolonged exposure at close range to unshielded areas of the

picture tube to prevent exposure to X-ray radiation.

The Test Picture Tube used for servicing the chassis at the bench

should incorporate safety glass and magnetic shielding. The safety

glass provides shielding for the tube viewing area against X-ray radiation

as well as implosion. The magnetic shield limits X-ray radiation around

the bell of the picture tube in addition to restricting magnetic effects.

When using a picture tube test jig for service, ensure that the jig is

capable of handling 31kV without causing X-ray radiation.

Before returning a serviced receiver to the owner, the service

technician must thoroughly test the unit to ensure that is completely

safe to operate. Do not use a line isolation transformer when testing.

Warning !It is essential that these critical parts are replacedwith the manufacturer’s specified replacement partsto prevent X-ray radiation, shock, fire or other haz-ards.

!

ABOUT LEAD FREE SOLDER (PBF) ........................................................ 3

SUGGESTED PBF SOLDER .................................................................... 3

HOW TO RECOGNIZE THAT PB FREE SOLDER IS USED ......................... 3

IC601 - PINOUT ...................................................................................... 5

IC601 - PINOUT ....................................................................................... 6

IC VOLTAGE TABLES ............................................................................. 6

IC601 - BLOCK DIAGRAM ...................................................................... 7

GP31 CHASSIS FEATURE SUMMARY .................................................... 8

DAC CONTROL FOR GP31 CHASSIS FUNCTIONS AND ADJUSTMENTS ......... 9

HOW TO RESET THE UNIT (SELF CHECK) ............................................... 9

HOW TO ENTER IN THE SERVICE MODE ................................................. 9

CHK1 MODE - OPTIONS ......................................................................... 9

ADJUSTMENTS ....................................................................................... 10

CHK2 MODE - VCJ ADJUSTMENTS ....................................................... 10

CHK3 MODE - PINCUSHION ADJUSTMENTS ......................................... 10

EEPROM MEMORY MAPS ...................................................................... 11

ADJUSTMENTS ....................................................................................... 13

CRT P.C.B. .............................................................................................. 18

SCHEMATICS DIAGRAMS ....................................................................... 18

SHEMATIC DIAGRAM P.C.B. ................................................................... 19

MAIN P.C.B. ............................................................................................. 20

SIGNAL WAVEFORM .............................................................................. 21

EXPLODED VIEW .................................................................................... 25

REPLACEMENT MECHANICAL PARTS LIST .......................................... 26

REPLACEMENT ELECTRICAL PARTS LIST ............................................ 27

- 3 -

TC-20KL05P

ABOUT LEAD FREE SOLDER (PbF)

Note:In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder thatcontains lead.We will use PbF solder when discussing the lead free solder used in our manufacturing process which is made from Tin (Sn),Silver, (Ag), and Copper, (Cu).This model, and others like it, manufactured using lead free solder will have PbF stamped on the PCB. For service and repairwork we suggest using the same type of solder although, with some precautions, standard Pb solder can also be used.

Caution• PbF solder has a melting point that is 50° ~ 70° F, (30° ~ 40°C) higher than Pb solder. Please use a soldering iron with

temperature control and adjust it to 700° ± 20° F, (370° ± 10°C).In case of using high temperature soldering iron, please becareful not to heat too long.

• PbF solder will tend to splash if it is heated much higher than its melting point, approximately 1100°F, (600°C).• If you must use Pb solder on a PCB manufactured using PbF solder, remove as much of the original PbF solder as possible

and be sure that any remaining is melted prior to applying the Pb solder.• When applying PbF solder to double layered boards, please check the component side for excess which may flow onto the

opposite side (See figure, below).

SUGGESTED PbF SOLDERThere are several types of PbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper,(Sn+Ag+Cu), you can also use Tin and Copper, (Sn+Cu), or Tin, Zinc, and Bismuth, (Sn+Zn+Bi). Please check the manufacturer’s specific instructions for the melting points of their products and any precautions for using their product with othermaterials.The following lead free (PbF) solder wire sizes are recommended for service of this product: 0.3mm, 0.6mm and 1.0mm.

HOW TO RECOGNIZE THAT PB FREE SOLDER IS USEDP.C.Boards marked as “PbF” use Pb Free solder. (See the figure below.) Pb Free is not used the Power Supply Board of thisunit.(Example : Digital Board)

CN612

18

E

L659

L661

L660

IC605

R70

L619

L618

C66

7

R70

8L6

30

R61

1

F60

5R

736

L620

L621

R72

3

R61

3R

610

C71

7C

731

C69

4

L655

L643

L604

L606

L605

R76

7R

769

R76

8L6

56L6

57

S

CH

Q609

75

51

50

2625

1

76

100

C738

C668

RA610

RA609

D602

J600

8

1

9

IC610

Q613

C726

D607

D608

R737

E Q620

16

L624L625L626

L658

L653

L654

L642

C666

BAT600

PFUP1330YA PbF

RA602

C672

C728

+24V

+3.3V/BAT

25

DIGITAL BOARD COMPONENT VIEW

Marked

- 4 -

TC-20KL05P

Loca

tion

of C

ontro

ls

Fro

ntV

iew

Pow

er

sw

itch

Channel

buttons

ME

NU

buttonTV

/AV

button

Ba

ck

Vie

w

Vo

lum

ebu

tto

ns

Re

mo

teco

ntr

ol

se

nso

r

Ind

ica

tio

n lig

ht

An

ten

na

inp

ut

jack

Au

dio

/Vid

eo

inp

ut

jack

Au

dio

/Vid

eo

ou

tpu

t

SA

ÍDA

EN

TR

AD

A

VÍD

EO

MO

NIT

OR

MO

NO ÁU

DIO

RL

ME

NU

TV

/AV

–+

AV

IN

L/M

ON

OR

VID

EO

AU

DIO

Vid

eo

inp

ut

Au

dio

inp

ut

Ea

rph

on

eo

utp

ut

Pa

na

son

ic

Loca

tion

of C

ontro

ls

Rem

ote

Co

ntro

l

Pa

na

son

ic

u e

12

3

45

6

78

9

0R

-TU

NE

WA

KE

UP

TV

/AV

CC

PIC

ME

NU

MA

IN M

EN

U

SO

UN

DM

EN

US

AP

SU

RR

OU

ND

VOL–

VOL+

CH CHN

SA

PS

UR

RO

UN

D

SO

UN

D M

EN

U

PIC

ME

NU

MA

IN M

EN

U

PO

WE

R

TIM

ER

MU

TE

TV

/AV

RE

CA

LL

NO

RM

AL

IZAT

ION

VO

LU

ME

AN

D M

EN

UN

AV

IGAT

ION

CH

AN

NE

LS

KE

YB

OA

RD

FO

RD

IRE

CT

SE

LE

CT

ION

WA

KE

UP

R-T

UN

E

CL

OS

ED

CA

PT

ION

CH

AN

NE

LS

SE

LE

CT

ION

AN

DM

EN

U N

AV

IGAT

ION

VOL–

VOL+

CH CHN

- 5 -

TC-20KL05P

P3.1/ADC1 1 port 3.1 or ADC1 input

P3.2/ADC2 2 port 3.2 or ADC2 input

P3.3/ADC3 3 port 3.3 or ADC3 input

VSSC/P 4 digital ground for m-Controller core and periphery

P0.5 5 port 0.5 (8 mA current sinking capability for direct drive of LEDs)

P0.6/CVBSTD 6 port 0.6 (8 mA current sinking capability for direct drive of LEDs) or Composite video input. A positive-going

VSSA 7 digital ground of TV-processor

SECPLL 8 SECAM PLL decoupling

VP2 9 2nd supply voltage TV-processor (+8V)

DECDIG 10 supply voltage decoupling of digital circuit of TV-processor

PH2LF 11 phase-2 filter

PH1LF 12 phase-1 filter

GND3 13 ground 3 for TV-processor

DECBG 14 bandgap decoupling

AVL 15 Automatic volume levelling

VDRB 16 vertical drive B output

VDRA 17 vertical drive A output

IFIN1 18 IF input 1

IFIN2 19 IF input 2

IREF 20 reference current input

VSC 21 vertical sawtooth capacitor

AGCOUT 22 tuner AGC output

NC 23 Not connected

NC 24 Not connected

GND2 25 ground 2 for TV processor

SNDPLL 26 narrow band PLL filter

IC 27 Inter nally connected

AUDIO2 28 audio 2 input

AUDIO3 29 audio 3 input

HOUT 30 horizontal output

FBISO 31 flyback input/sandcastle output

DECSDEM 32 decoupling sound demodulator

AUDEEM 33 Deemphasis (front-end audio out)

EHTO 34 EHT/overvoltage protection input

PLLIF 35 IF-PLL loop filter

IC 36 Internally connected

IC 37 Internally connected

IFVO/SVO 38 IF video output / selected CVBS output

VP1 39 main supply voltage TV processor

CVBS1 40 internal CVBS input

GND 41 ground for TV processor

CVBS2 42 external CVBS2 input

GND 43 ground for TV-processor

CVBS3/Y 44 CVBS3/Y input

C 45 chroma input

WHSTR 46 white stretch capacitor

CVBSO 47 CVBS output

AUDOUT 48 Audio output

NC 49 Not connected

INSSW2 50 2nd RGB / YUV insertion input

R2/VIN 51 2nd R input / V (R-Y) input / PR input

G2/YIN 52 2nd G input / Y input

B2/UIN 53 2nd B input / U (B-Y) input / PB input

BCLIN 54 beam current limiter input

BLKIN 55 black current input / V-guard input

RO 56 Red output

GO 57 Green output

BO 58 Blue output

VDDA 59 analog supply of Teletext decoder and digital supply of TV-processor (3.3 V)

Symbol Pin Description

IC601 - PINOUT

- 6 -

TC-20KL05P

Pin Voltage1 3,32 5,03 1,84 05 4,56 07 08 2,39 8,010 5,011 3,212 4,013 014 4,015 0,216 1,317 1,318 1,919 1,920 4,021 3,822 023 024 025 026 027 2,528 3,729 3,730 0,631 0,632 2,233 3,134 1,635 1,536 2,437 1,538 2,839 8,040 3,6

Pin Voltage41 042 3,843 044 3,345 046 3,547 3,048 3,349 050 2,551 2,552 2,553 2,554 2,055 5,356 4,057 3,858 3,859 3,360 061 3,362 063 1,664 1,665 066 3,367 3,368 5,069 5,070 3,271 072 5,073 074 0,275 076 077 078 079 080 0

IC601Pin Voltage1 0,3V2 0,14V3 -12V4 -14V5 0V6 15V7 3V

IC451Pin Voltage1 187V3 0,5V4 22,5V5 0,1V6 1,3V7 0,5V

IC801

Pino Tensão1 11,5V2 5V3 0V4 5V5 2,8V6 1,5V7 0V8 0V9 0,5V

IC2301Pino Tensão1 5V2 0V3 1,27V4 3,3V5 0V6 5V

IC1201

Pin Voltage1 141V2 9V3 0V

IC802Pin Voltage1 10,4V2 5V3 0V

IC880

VPE 60 OTP Programming Voltage

VDDC 61 digital supply to core (3.3 V)

OSCGND 62 oscillator ground supply

XTALIN 63 crystal oscillator input

XTALOUT 64 crystal oscillator output

RESET 65 reset

VDDP 66 digital supply to periphery (+3.3 V)

P1.0/INT1 67 port 1.0 or external interrupt 1 input

P1.1/T0 68 port 1.1 or Counter/Timer 0 input

P1.2/INT0 69 port 1.2 or external interrupt 0 input

P1.3/T1 70 port 1.3 or Counter/Timer 1 input

P1.6/SCL 71 port 1.6 or I2C-bus clock line

P1.7/SDA 72 port 1.7 or I2C-bus data line

P2.0/TPWM 73 port 2.0 or Tuning PWM output

P2.1/PWM0 74 port 2.1

P2.2/PWM1 75 port 2.2

P2.3/PWM2 76 port 2.3

P2.4/PWM3 77 port 2.4

P2.5/PWM4 78 port 2.5

Sync F. 79 Sync Filter

P3.0/ADC0 80 port 3.0 or ADC0 input

Symbol Pin Description

Pin Voltage1 10,7V2 10,7V3 3,3V4 0V5 3,1V6 8V7 5V

IC851

IC601 - PINOUT

IC VOLTAGE TABLES

All voltage measurements were made in POWER ON mode, with 127V 60Hz powersource and Color Bars Video Pattern.

- 7 -

TC-20KL05P

SO

UN

D

TR

AP

TU

NE

RA

GC

+8V

HO

UT

V-D

RIV

E

RO

GO

BO

BC

LIN

BLK

IN

CV

BS

3/Y

SIF

IN

AUDOUT

C

SD

AS

CL

VIS

ION

IF

PLL D

EM

OD

.

AG

C/A

FC

VID

EO

AM

P.

VID

EO

SW

ITC

H

VID

EO

ID

EN

T.

VID

EO

FIL

TE

RS

PA

L/S

EC

AM

/NT

SC

DE

CO

DE

R

DE

EM

PH

AS

IS

AU

DIO

SW

ITC

HA

VL

VO

LU

ME

CO

NT

RO

L

BA

SE

-BA

ND

DE

LA

Y L

INE

H/V

SY

NC

SE

P.

H-O

SC

. +

PLL

H-D

RIV

E

2nd L

OO

P

H-S

HIF

T

V-D

RIV

E +

CO

NT

R/B

RIG

HT

N

OS

D/T

EX

T IN

SE

RT

CC

CW

HIT

E-P

. A

DJ.

80C

51 C

PU

I2C

-BU

S

TR

AN

SC

EIV

ER

RO

M/R

AM

TE

LE

TE

XT

AC

QU

ISIT

ION

1/1

0 P

AG

E

ME

MO

RY

TE

LE

TE

XT

/OS

D

DIS

PLA

Y

RG

BB

L

Y U V

H

V

RE

F

EN

HA

NC

ED

VS

T P

WM

-DA

C

VST OUT

I/O

PO

RT

S

I/O PORTS (4x)

+3.3

V

RESET

LED OUT (2x)

ADC IN (4x)

VPE

EW

GE

OM

ET

RY

GE

OM

ET

RY

EH

TO

(EW

D)

R/V

G/Y

B/U

BL

RG

B/Y

UV

IN

SE

RT

RG

B

RE

F

CV

BS

SY

NC

H V

CO

R

SA

TU

RA

TIO

N

LU

MA

DE

LA

Y

PE

AK

ING

BLA

CK

ST

RE

TC

H

QS

S S

OU

ND

IF

AG

C

QS

S M

IXE

R

AM

DE

MO

DU

LT

OR

SO

UN

D P

LL

CV

BS

2VIF

IN

CV

BS

O

QSSO/AMOUT

PWMS(4X)

WH

ITE

ST

RE

TC

H

BLU

E S

TR

ET

CH

AUDIO2

AUDIO3

AUDEEM

(AVL)

(SNDIF)

VM

OU

T

VM

OU

T

IFV

O

TIN

T C

ON

TR

OL

Y

IC601 - BLOCK DIAGRAM

- 8 -

TC-20KL05P

CHASSIS : GP31MODEL : TC-20KL05PSYSTEM : 3 system (PAL-M/PAL-N/NTSC) (PAL-M 50Hz)

POWER SOURCE : AC automatic power switching (127/220)V, 50/60Hz

MEMORY : 125 positions

TV TUNING RANGE : 181 channels (TV / CATV)

OSD LANGUAGE : Spanish , Portuguese and English

AUDIO SYSTEM : Mono

VERTICAL MAGNEGTIC FELD : -0.1 ± 0.03 (PANALAT)

COLOR TEMPERATURE : (High Light) x= 0.275±0.01, y=0.284 ±0.01, Y=150 (nit))

(Low Light) x= 0.273±0.01, y=0.283 ±0.01, Y=7.0 (nit)

REFERENCE VOLTAGE

+B VOLTAGE

Sound confirmation

PAL color output

NTSC color output

Anode (EHT) voltage

Memory Data

140 ± 1,5V

8 ±1V

5 ±1V

175 ±1V

0.5 Vp-p

2.25 ±0.1Vo-p

2.25 ±0.5Vo-p

2.5 ±0.5Vo-p

26.5 +0.7 (kV)

26.5 -1.5 (kV)

002

007

009

010

008

CONTENTS REFERENCE TEST POINT

TPA10

TPA8

TPA9

TPA21

Between A22-1 and A22-3

or A22-2 and A22-4

TPL2

TPL1

TPL1

CRT

ANODE

POINTS

D

C

C

SPECIFICATIONS

[A]=C0H, [B]=00H, [C]=00H, [D]=B3H, [E]=06H, [F]=01H, [G]=00H, [H]=09H

GP31 CHASSIS FEATURE SUMMARY

- 9 -

TC-20KL05P

TABLE CHK1

Values

C00000B306010009

OPTION1OPTION2OPTION3OPTION4OPTION5OPTION6OPTION7OPTION8

DAC CONTROL FOR GP31 CHASSIS FUNCTIONS AND ADJUSTMENTS

CHK1 MODE - OPTIONSOn CHK1 mode it is possible to adjust the items of the table shown here.Note:To select an option, type “4” to move forward and “3” to move back.After having selected the desired option, adjust it by pressing the “VOL(_)” or “VOL(+)”keys.Press “0” to memorize the adjustment.

Observation:Values of CHK1 table in should be programed, exactly as described in the tableshown here.

HOW TO RESET THE UNIT (SELF CHECK)To reset the unit, press simultaneously “VOLUME (–)” on the front panel and “TIMER” on the remote control.

HOW TO ENTER IN THE SERVICE MODE:1. Adjust “OFF TIMER” to 30 minutes.

Press simultaneously “VOLUME (–)” on the front panel and “RECALL” on the remote control to enter “SERVICEMODE”.After a couple of seconds, the expression “CHK1” should appear on the right superior side of the TV screen.

2. To change to memory data, press ”MUTE” and ”VOLUME(_)” simultaneously while the OSD is still on CHK1 mode.

3. Press key “2” to move forward and “8” to move backward each page (8h positions) in the memory.Exemple: Memory position is 100. After pressing “2” the cursor will go to position 0F8 and after pressing “8” the cursorwill go to position 108 .

4. Press “4” and “6” to move to right or left.

5. Press “CH(+)” e “CH(–)” to move for blocks.Example: Initial memory position is 000. By pressing “CH(+)” cursor will go to position 100, pressing it once again thecursor will go to position 200. The key “CH(–)” does the inverse move.

6. To change values in the memory, press “VOLUME(+)” to increase and ”VOLUME(_)” to decrease.

7. After data adjustment, OSD will change to RED color. Press “0” to memorize the adjustment and the OSD will change toGREEN color.

NOTE:To alter from CHK1 mode to CHK2, CHK3 or CHK4 mode, press key “2” to move forward and key “1” to move back, asilustrad below.

Turn Off

NORMAL MODE SERVICE MODE

OPTION CODESETTING

“2”

“1”

VCJADJUSTMENT

CHK1“2” “2”

“1” “1”

PINCUSHIONADJUSTMENT

WHITE BALANCEADJUSTMENT

CHK2 CHK3 CHK4

- 10 -

TC-20KL05P

CHK2 MODE TABLE

Reference values

231005028502850

RF AGCCONTRASTCOLOURSUB COLOURTINTSUB NTSC-TINTBRIGHT

CHK3 MODE TABLE

Reference values

32374345

V-SLOPEV-SHIFTV-AMPH-SHIFT

CHK4 MODE TABLE

Reference values

28305030

100113331352

R-CUTG-CUTBRIGHTSUB-BRIGHTCONTRASTSUB- CONTRASTR-DRIVEG-DRIVEB-DRIVERGB-CONTRAST

ADJUSTMENTS

CHK2 MODE - VCJ ADJUSTMENTSOn CHK2 mode it is possible to adjust the items of the table shown here.Note:To select an item, type “4” to move forward and “3” to move back.After having selected the desired option, adjust it by pressing the “VOL(_)” or“VOL(+)” keys.

CHK3 MODE - PINCUSHION ADJUSTMENTSOn CHK3 mode it is possible to adjust the items of the table shown here.Note:To select an item, type “4” to move forward and “3” to move back.After having selected the desired option, adjust it by pressing the “VOL(_)” or“VOL(+)” keys.

CHK4 MODE - WHITE BALANCE ADJUSTMENTSOn CHK4 mode it is possible to adjust the items of the table shown here.Note:To select an item, type “4” to move forward and “3” to move back.After having selected the desired option, adjust it by pressing the “VOL(_)” or“VOL(+)” keys.

Observation:The values of the tables CHK2, CHK3 and CHK4 are reference values and they can vary, according to each receiver.

TO EXIT SERVICE MODE AND RETURN TO NORMAL MODETo exit SERVICE MODE, turn off or reset (SELF CHECK) the television.

- 11 -

TC-20KL05P

EEPROM MEMORY MAPS

TABLE 0

0 1 2 3 4 5 6 7 8 9 A B C D E F

0 00 00 06 01 00 06 02 00 06 03 00 06 04 00 06 05

1 00 06 06 00 06 07 00 06 08 00 06 09 00 06 0A 00

2 06 0B 00 06 0C 00 06 0D 00 06 0E 00 06 0F 00 06

3 10 00 06 11 00 06 12 00 06 13 00 06 14 00 06 15

4 00 06 16 00 06 17 00 06 18 00 06 19 00 06 1A 00

5 06 1B 00 06 1C 00 06 1D 00 06 1E 00 06 1F 00 06

6 20 00 06 21 00 06 22 00 06 23 00 06 24 00 06 25

7 00 06 26 00 06 27 00 06 28 00 06 29 00 06 2A 00

8 06 2B 00 06 2C 00 06 2D 00 06 2E 00 06 2F 00 06

9 30 00 06 31 00 06 32 00 06 33 00 06 34 00 06 35

A 00 06 36 00 06 37 00 06 38 00 06 39 00 06 3A 00

B 06 3B 00 06 3C 00 06 3D 00 06 3E 00 06 3F 00 06

C 40 00 06 41 00 06 42 00 06 43 00 06 44 00 06 45

D 00 06 46 00 06 47 00 06 48 00 06 49 00 06 4A 00

E 06 4B 00 06 4C 00 06 4D 00 06 4E 00 06 4F 00 06

F 50 00 06 51 00 06 52 00 06 53 00 06 54 00 06 55

COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

TABLE 1

0 1 2 3 4 5 6 7 8 9 A B C D E F

0 00 06 56 00 06 57 00 06 58 00 06 59 00 06 5A 00

1 06 5B 00 06 5C 00 06 5D 00 06 5E 00 06 5F 00 06

2 60 00 06 61 00 06 62 00 06 63 00 06 64 00 06 65

3 00 06 66 00 06 67 00 06 68 00 06 69 00 06 6A 00

4 06 6B 00 06 6C 00 06 6D 00 06 6E 00 06 6F 00 06

5 70 00 06 71 00 06 72 00 06 73 00 06 74 00 06 75

6 00 06 76 00 06 77 00 06 78 00 06 79 00 06 7A 00

7 06 7B 00 06 7C 00 06 7D 00 06 67 69 6A 6C 6E 70

8 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

9 FF FF FF FF FF FF FF FF FF FF FF FF FF 72 74 76

A 06 06 FF FF 00 00 00 00 00 00 01 02 01 02 03 04

B FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

C FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

D FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

E 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

F 00 00 00 00 00 00 3A 2A 00 00 00 00 00 00 00 00

COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

COLUMN

- 12 -

TC-20KL05P

TABLE 2

0 1 2 3 4 5 6 7 8 9 A B C D E F

0 02 00 A5 5A 01 02 01 01 00 08 00 04 FF 00 01 00

1 00 00 00 00 00 00 12 0D 0A 15 16 0B 0C 0C 0C 0B

2 00 00 00 00 0F 0E 00 00 00 00 FF 16 00 00 00 00

3 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

4 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

5 32 32 32 64 4B 32 32 32 4B 44 2D 32 32 41 32 32

6 16 0E 0B 0E 12 28 D0 0E FF 0C 04 04 16 *2 FC 0E

7 00 00 *3 13 13 13 37 37 37 37 70 02 03 02 00 00

8 32 32 32 64 4B 32 32 32 4B 44 2D 32 32 41 32 12

9 0D 0A 11 12 0B 0C 0C 08 03 16 0E 0B 0B 0F 00 00

A 00 FF FF FF 00 00 00 FF FF FF 00 00 00 FF FF 02

B 01 19 15 *1 00 09 0C FF 1C 0C 04 04 70 02 70 02

C 03 03 03 12 12 12 12 03 03 03 03 03 03 03 03 40

D 10 60 10 04 20 0D FF 01 00 03 FF 01 00 00 00 00

E 00 00 FF FF FF FF FF FF A B C D E F G H

F 00 FF 1C 1D 0F 24 2C 32 38 3E 44 4A 50 A5 3F A5

COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

TABLE 3

0 1 2 3 4 5 6 7 8 9 A B C D E F

0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

1 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

2 00 00 00 00 00 10 FF 00 00 00 22 88 26 20 23 21

3 FF 23 1E 26 17 1A 0F 21 25 12 1D 19 1C 17 1B 1F

4 21 FF 0C 00 FD 00 1C 25 80 00 2A 00 35 20 30 21

5 02 48 12 44 02 80 34 01 FE 00 00 00 FD 01 00 00

6 01 FE 2C 12 21 19 00 00 00 00 00 00 00 00 00 00

7 00 00 00 00 00 00 00 00 00 06 00 00 00 00 00 00

8 00 00 00 00 00 00 00 00 08 11 0C 0C 08 0C 0C 02

9 09 00 FB 00 00 00 00 0A F8 00 00 00 00 00 00 03

A 01 03 02 03 03 00 34 2B 2B 2F 20 63 03 14 03 00

B CA 49 4B 02 31 00 00 FF FD 04 05 03 03 EB FE F2

C 20 07 4F 41 00 FE FE 0E 0F 0E 0D 0E 0C 00 00 00

D 05 0A 01 00 FE FE 00 00 00 F7 00 F0 01 24 00 08

E 10 04 2F 71 76 3B 3A 02 02 0E 3A 37 00 11 0B 05

F 33 30 2A 27 26 25 24 54 59 63 00 FF 34 FF FF 03

COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN COLUMN

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

LINE

COLUMN COLUMN

- 13 -

TC-20KL05P

20" SAMSUNG A48KRD89X 6,25 ± 0,25 Vrms20" PHILIPS A48EAK01X 6,15 ± 0,25 Vrms

ADJUSTMENTS

ITEM / PREPARATION PROCEDURE

2- VIF DETECTOR OUTPUT LEVEL CONFIRMATION CONFIRMATION:

1. Install the chassis in the VIF calibration JIG and tune in a63 dBU colorbar pattern (75Ω opened).

2. Connect the oscilloscope in TPA31.3. Confirm that the output video sign is 1.05 ± 0.15 Vp-p in

TPA 31.

3- BUZZING CONFIRMATION (AUDIO CIRCUIT)

1. Connect the oscilloscope with a 7kHz filter between A22-2 andA22-3 speakers terminals .Adjust the sound to maximum.

2. Para modelos MONO:Adjust AVL: OFF

CONFIRMATION:

1. Supply a colorbar signal with local frequency adjustedand the AFC ON (Channel with sound bearer and withoutmodulation).

2. Assure that the width in the buzzing waveform is smallerthan 500 m Vp-p.

1- RF AGC ADJUSTMENT

1. Supply a color bar PHILIPS pattern and adjust the RFinput signal of 69 dB mV (75W opened channel 7 RFfreq.: 175.25 MHz).

2. Connect the digital multimeter in TPA15.

ADJUSTMENT:

1. Select “RF AGC” on “CHK2” service mode.2. Adjust "RF AGC" by pressing VOL(+) or (-) until obtaining

2.2±0.1V in TPA15.3. Increase the input level by +2 dB and confirm that the

voltage decreases in TPA15.

CONFIRMATION

1. Connect a voltage meter between TPA10 and ground.Confirm that the voltage +B is within a range of 140.5V±1.5V

2. Connect a high frequency voltage meter (VRMS) amongthe heater, and confirm that the voltage is according tothe table below:

3. Connect the high voltage meter in the CRT anode pin,and confirm that the high voltage is be around 27,2~25KVfor 20" CRT .

4- ANODE AND HEATER VOLTAGE CONFIRMATION

1. Supply a crosshatch signal.2. Adjust the current beam to zero. (0 beam).3. Adjust “SCREEN VR” and “CONTRAST” to minimum.

Note:(When using a high voltage meter resistive type, it isnecessary to use an electrostatic meter type to verify thevalues)

BALANCESURROUNDHYPER BASSAVLSOUND MENU

CENTEROFFOFFOFFDIALOG

For STEREO models: smaller than500 m Vp-p

7KHz Filter

- 14 -

TC-20KL05P

Condition/ModelABC

20” Philips23,324,527,4

ADJUSTMENTS

5- PAL COLOR OUTPUT SIGNAL ADJUSTMENT

1. Supply a color bar signal and adjust the local frequency.2. Adjust “IMAGE” to DYNAMIC NORMAL, “CONTRAST” to

63 and “SUB-CONTRAST” to 21.3. Adjust the “CHANNEL COLOR” level to NORMAL.4. Set to CHK2 service mode option, press “5” on the remote

control unit and confirm that OSD becomes blue (AKBturned off).

5. Set ABL to OFF (in CHK2 mode, to access BRT, CONT,S-CONT or S-TINT).

6. Adjust [A] for 2.3 ± 0.2V through the BRIGHT controlvariation in the test point TPL2.

7. Confirm that the RGB Contrast is 11DAC and {352} = 1B

8. Fix G-DRIVE GAIN, R-DRIVE GAIN and B-DRIVE GAINdata in 1FH or 31 DAC.

R-DRIVE GAIN: [SLV(8A), SUB (16)]G-DRIVE GAIN: [SLV(8A), SUB (17)]B-DRIVE GAIN: [SLV(8A), SUB (18)]

CALIBRATION:

1. Connect the oscilloscope in TPL2 (G-OUT) with a 10KΩresistor and adjust “CONTRAST”, so that the [B] waveformit is 2.6±0.1V.

2. Adjust “SUB-COLOR” to obtain 2,45±0.5V in [D]according to fig. 1.

3. Connect the oscilloscope in TPL1 (R-OUT) with a 10KΩresistor and confirm that the [C] waveform it is 2.45±0.5Vaccording to fig. 2.

4. Press the key “5” (AKB ON) and confirm that OSDbecomes white.

Fig. 1

A = 2.0 ±0.2Vo-pB = 2.3±0.5VD = 2.15±0.5V

Fig. 2

A = 2.0 ±0.2Vo-pC = 2.5±0.5V

6- NTSC SUB-TINT CALIBRATION

1. Connect the oscilloscope in TPL1 (R-OUT) with a 10KΩresistor.

2. Supply a Rainbow signal (NTSC 3.58 MHz) throughVIDEO IN.

3. Select “IMAGE” to DYNAMIC NORMAL.4. Select “COLOR FOR CHANNEL” to NORMAL.5. On CHK2 service mode, press “5” (AKB OFF) and confirm

that OSD becomes blue (AKB turned off).6. Set ABL to OFF (on CHK2 mode, to access BRT, CONT,

S-CONT or S-TINT).

CALIBRATION:

1. Adjust [C] for 5.0±0.2V through the BRIGHT controlvariation (CHK2) according to fig. 1.

2. Adjust SUB TINT-NTSC so that the levels of positions 2, 3and 4 of Fig. 1 in accordance with the Fig. 2.

3. Set ABL to ON.4. Press “5” and confirm that OSD becomes white (AKB

turned on).

Fig. 1 Fig. 2

7- PROTECTION CIRCUIT (SHUTDOWN)CONFIRMATION OF OPERATION

1. Supply a crosshatch pattern signal and adjust theCONTRAST and BRIGHT DAC controls to minimum.(Ibeam=0 μA)

CONFIRMATION:

1. Connect the voltmeter in TPA22 and confirm that thevoltage is smaller than [A].

2. Connect a DC source in TPA22 and confirm that theprotection circuit doesn't act when the voltage is [B].

3. Confirm that the protection circuit acts with smaller voltagethan [C].

4. Use D512 catode or C511 (+) terminal, if TP22 access ifit is difficult to access TP22.

ITEM / PREPARATION PROCEDURE

- 15 -

TC-20KL05P

ADJUSTMENTS

Fig. 11 2 3 3 2 1

Fig. 2

9- FOCUS CALIBRATION

• Assure that the SUB-BRIGHTNESS adjustment has beendone.

1. Supply a Philips or monoscope pattern signal.2. Adjust IMAGE MENU to DYNAMIC NORMAL.

CALIBRATION:

1. Adjust the FOCUS variable resistor for the point of betteradjustment.

• with PHILIPS signal .... take as reference for adjustmentthe third vertical line (fig. 1).

• with MONOSCOPE signal in the number 4 (fig.2).

8- SUB-BRIGHT AND SUB-CONTRASTCALIBRATION

1. Supply a WINDOW pattern signal.2. Adjust IMAGE MENU to DYNAMIC NORMAL

SUB-BRIGHT CALIBRATION

1. Position the color analyzer in the LOW LIGHT imagearea.

2. Ajust S-BRT <CHK 4> control, so that it is Y=0,7±0,2.

SUB-CONTRAST CALIBRATION

1. Position the color analyzer in the HIGH LIGHT imagearea.

2. Ajust S-CONT <CHK 4> DAC control, so that it isY=230±10.

3. If impossible to obtain that adjustment, adjust SUB-CONT <CHK 4> again.

4. Check the SUB-BRIGHT adjust.

10- PURITY CALIBRATION

1. Adjust the HELMHOLTZ device for the local magnetic field(HORIZONTAL: 0 ± 0.03 X 10-4T)

2. Let the set warm up (aging time) for a minimum of 60minutes.

3. Supply a purity pattern (white pattern).

4. Adjust CONTRAST and BRIGHT to MAXIMUM.

5. The static convergence adjustment must have beenmade preliminarily.

6. Connect a DC ampere meter between FBT pin11 (-) andFBT pin3 (+), and adjust to 920μA±10%, varying the S-BRT DAC control.

CALIBRATION:

1. Position the “ears” of the purity magnets both upward.

2. Adjust the purity until the markers in the purity jigmonitorscope becomes symmetrical in the horizontaldirection.

3. The vertical centralization correction is made throughthe purity magnets for stripe CRT type only.

4. Slide the yoke forward by 10 mm±5 in the monitor. Then,tighten the deflection yoke.

5. Repeat the procedures 2 ~ 3 ~ 4.

6. Press the belt of deflection yoke.

7. Adjust “beam landing” using a microscope. (for modelchange or instrument check only)

4

ITEM / PREPARATION PROCEDURE

- 16 -

TC-20KL05P

ADJUSTMENTS

ITEM / PREPARATION PROCEDURE

11- WHITE QUALITY CALIBRATION

PREPARATION:

1. Adjust the HELMHOLTZ device to local magnetic field. Ho-rizontal: 0 ± 0.003 x 10-4T

2. Receive a white purity pattern.

3. Adjust CONTRAST and BRIGHT controls to maximum.

4. Previously adjust the CONVERGENCE.

5. Fully degauss the CRT by using an external degaussingcoil.

CALIBRATION:1. Adjust the magnetic field in 0.4x10-4T (400 mG), and

check the white quality with the CRT turned to EAST andto WEST.

2. Receive a red pattern, adjust the COLOR control tomaximum and confirm the purity adjustment.

3. If purity error is found at the CRT corners, apply magnetictapes to correct it, fully degauss the CRT again and repeatthe steps 1 and 2. Don't use this magnetic tapes on theinternal side of the yoke.

4. When magnetic tapes be used, fully degauss the face ofCRT (in a horizontal magnetic field = 0 ± 0.03x10-4T),and repeat the items 1 and 2.

5. Adjust the control of COLOR to MINIMUM, and repeatingthe item 1.

12- CONVERGENCE CALIBRATION

1. Adjust the HELMHOLTZ device to local magnetic field.

2. Receive a crosshatch pattern.

3. Adjust IMAGE menu to DINÂMIC NORMAL and the DACBRIGHT control for the crosshatch pattern to be gray.

4. Remove the DY wedges and slightly tilt the deflectionyoke to the vertically and horizontally to obtain the goodoverall convergence.

5. If purity error is found, repeat “Color Purity” adjustment

CALIBRATION

Static convergence calibration

l) Assure that the magnets are positioned according toillustration 1.

ll) Adjust the 4 poles magnets to align the R and BCENTRAL DOTS and adjust the 6 poles magnets toalign both DOTS with G.

lll) After adjustment above, assure that the magnets aresealed, through the application of white glue.

Note:

The electron beams are moved rotationally when thestatic convergence magnets are rotated.

The reduction of rotational beams differ depending ofthe two magnets angle. Therefore, it is necessary torepeat the magnets calibrations sometimes, untilobtaining a good alignment.

13- CRT CUT OFF CALIBRATION1. Supply a WINDOWS signal.

2. Position DACs with the data below:

BRT —> 50H

S-BRT —> 31H

RGB CONTRAST —> 02DAC

SUB-CONTRAST —> 21H

R,G,B DRIVE —> 31H

R,G CUT —> 31H

CALIBRATION:1. Press “5” (AKB OFF) and confirm that OSD becomes

blue.

2. Connect the oscilloscope in TPL5 and adjust BRT toobtain 130V as in the Fig. 1 below.

3. Adjust the SCREEN to obtain a horizontal fine line in thescreen center.

4. Press “5” (AKB ON) and confirm that OSD becomeswhite.

4 poles magnets (R-B)

6 poles magnets (R-G-B)

Fig. 1

- 17 -

TC-20KL05P

ADJUSTMENTS

ITEM / PREPARATION PROCEDURE

14- VERTICAL DEFLECTION CALIBRATION ANDCONFIRMATION

1. Adjust IMAGE to DYNAMIC NORMAL

1) V-SLOPE CALIBRATION1. Supply a PHILIPS PAL-M signal.2. Adjust V_SLOPE <CHK3> so that the begin of the black

image part is aligned with the dividing line of Philipspattern. The dividing line of the Philips pattern circleshould be visible partially.

2) V-SHIFT 50Hz CALIBRATION1. Supply a PHILIPS PAL-N signal.2. Adjust the vertical centralization (V-SHIFT 50Hz) <CHK3>

so that PHILIPS pattern center be in the center of CRT.

3) V-SHIFT 60Hz CALIBRATION1. Supply a MONOSCOPE signal.2. Adjust the vertical centralization (V-SHIFT 60Hz) <CHK3>

so that MONOSCOPE pattern center be in the center ofCRT.

4) V-AMP 50Hz CALIBRATION1. Supply a PHILIPS PAL-N signal.2. Adjust the vertical height (V-AMP-50Hz) <CHK3> so that

the pattern PHILIPS circle height has the same dimensionof his width.

5) V-AMP 60Hz CALIBRATION1. Supply a MONOSCOPE signal.2. Adjust the vertical height (V-AMP-60Hz) <CHK3> so that

"C" and "D" values in illustration 2 it is 1.5 ~ 2.0 and to "A"and "B" values in illustration 2 it is 1.5 ~ 1.6.

3. To MEMORIZE in EEPROM.

Fig. 1

Fig. 2

15- WHITE BALANCE CALIBRATION

1. Adjust the HELMHOLTZ device to local magnetic field.2. Let the set warm up for a minimum of 30 minutes.3. Receive a white balance. (This sign should contain

burst sign).4. Adjust the IMAGE menu to DINÂMIC NORMAL.5. Fully degauss the CRT by using an external degaussing

coil.6. Position the color analyzer in contact with the CRT face.

CALIBRATION:

[1] LOW LIGHT CALIBRATION

1. Adjust S-BRT, so that Y = 7

2. Adjust R-CUT OFF, so that x = 0.273 ±0.01

3. Adjust G-CUT OFF, so that y = 0,283 ±0.01

[2] HIGH LIGHT CALIBRATION

(Confirm that G-DRIVE is 31 DAC)

1. Adjust S-BRT, so that Y = 150

2. Adjust R-DRIVE, so that x = 0,275 ±0.01

3. Adjust B-DRIVE, so that y = 0,284 ±0.01

[3] Repeat the procedures [1] and [2].

Assure that not entering light for the meter borders and that the CUT OFF voltage calibration has been done. If the value in thecolor analyzer is below 150, adjust CONTRAST to 50 and press “8” in CHK2 mode.

C,D

A,B

1.5 ~ 2.01.5 ~ 1.6

- 18 -

TC-20KL05P

SCHEMATICS DIAGRAMSCRT P.C.B.

TC-20KL05PP.C.B. SHEMATIC DIAGRAM - TC-20KL05P

- 19 -

- 20 -

TC-20KL05P

MAIN P.C.B.

43

21

58

76

E D C B A

34

56

78

ADEF BC

12

34

56

78

JS

550

C

L550

4

C 655

1 2 3

10

1

L VAR

JK

3102

2R3 89

R 2793

C3038

03C3 6

51Q5

L8

63

D5

84

R 845

C857

PC

86

0

C8

45

21

F

Q850

Q852

Q 578

L8 44

R604

D 0511

L8 54

R 056

L846

06R6

0R6 7

0R6 8

R6

09

10R6

L8

52

1R6 2

3L85

L 485

R1 111

R6

15

17R6

R619

R8

10

Q8

70

R8

11

Q8

71

L 3231

L 3331

D1120

R6

20

L862

3L31 6

L3137

R8

17

L8

63

23R6

R818

20R11

R820

R821

R824

R 258

L871

L872

R6

33

RM

1104

R8

30

C2

10

1

R8

31

10C2 2

R832

C 1032

1C2 04

4R6 0

10C2 5

1C2 06

4L88

C2

10

9

30C2 1

C 3022

30C2 3

1C2 10

3C2 04

30C2 5

R 418

C 1112

R 428

C 068

C 3062

1C2 13

C807

C 1142

Q2110

A4

C808

Q 1112

D11

51

C 1152

09C8

A6

L893

C 1172

C8

10

C814

C 1202

C 1212

R852

C8

16

C 1242

C8

18

R8

55

12C2 5

C819

C2

12

7

C2128

C6

28

R 1012

10R2 2

10R2 6

1R2 07

6R8 1

1R2 09

C8

25

C8

26

1JS 82

32C6

C 278

C2133

18JS 3

13C2 4

64R8

C6

34

C 1352

71R6

R 3022

R 668

C 1362

30R2 3

C 1372

13C2 8

C 1392

11R2 2

R 1132

C8

30

IC2301

D0

04

C2140

40C6

7R8 1

C 1412

C6

41

72R8

C 1422

R 738

TPA8

TPA

9

R 758

R6

86

8R6 7

88R6

1C2 51

C 1522

L 010

Q 1512

R2130

R 1312

C 508

C853

C 558

TPA11

D801

C862

D803

C8

64

111JS 0

R2151

R 1522

R2153

D810

15R2 4

1R2 55

D8

11

C8

75

C8

76

D8

17

C8

77

C878

C8

79

C685

C 866

C 876

TPA

30

C689

3TPA 1

TPA32

C2

38

0

D820

C8

80

IC801

C8

81

C2381

C8

82

D823

8C8 3

D8

24

38Q2 0

D825

Q2381

13C3 6

13C3 7

1C3 38

C3139TPA41

TPA

43

D830

D 318

14C3 3

C 1443

JS

004

00JS 5

D8

40

D 3802

SW

10

01

38D2 1

D2382

SW

10

02

SW

1003

SW

1004

R2380

SW

1005

R2381

R 3822

SW

1006

C3

15

7R 3832

R 3842

13R3 2

02R5

D8

50

D853

D8

54

D 558

D856

D857

R3141

R3

14

2R

31

43

R 1443

1R3 45

62D8

D8

63

J 210S 8

D 658

R5

19

R1

01

6R

10

17

C3

17

3

R1

01

8

JS

801

R1

01

9

C 173 5

JS

802

23JS 02

L 218

JS

2303

J 803S

L1 38

J 804S

JS

2304

1R3 50

JS

61

0

8JS 05

23JS 05

R3

15

1

JS806

R 1523

JS

807

1R3 53

D870

JS

808

R1

02

0

R3

15

4

IC851

R1

02

1

JS

809

D 718

JS

615

JS

810

23JS 10

JS

811

L11

01

JS

815

JS

816

Q 051 2

Q1053

8JS 17

L 1011

J 821S

JS2132

J 214S 0

J 214S 1

JS2142

I 80C8

R 0571

05R1 8

JS

840

R 0591

JS

841

JS844

8JS 45

JS

846

R 061 0

82R1

JS

852

85JS 3

J 854S

F801

8JS 60

JS

863

J 671S

JS

67

2

JS

870

L2

10

4

L2

10

5

L2

10

7

0L21 8

L2

30

3

L2

30

4

L2305

88JS 4

31JS 30

Q601

J 313S 2

Q 026

J 313S 3

JS

31

35

JS3136

31JS 37

8JS 93

3JS 140

31JS 4131JS 42

31JS 43

93C1

L2 301

L 3221

L2

13

3

L8

16

L 781C 0311

C 0411

L8 02

L821

C1105

A22

JS100

Q 408

S 80W 1

IC2

10

1

Q 1503

Q3151

Q3

03

1

D558

0R4 1

0R4 2

R 0323

03R4

R3

03

3

R 0343

R4

04

R3

03

5

R405

0R4 6

0R3 36

R407

JS110

0R3 38

0R4 9

0R3 39

21R0

111JS

J 12S1

R0

22

J 13S1

01R6

C11

25

17JS1

0R6 3

10R4

50JS 0

JS

501

J 502S

JS

503

R 144

R11

04

1R4 5

R11

05

1R4 6

R 0611

1R4 7

R 0483

R 0811

C1130

R 0911

C 3111

C1 321

2JS1 2

IC11

03 Q

1130

R1 101

R6

14

JS

51

0

JS

511

JS

512

1R11 2

R1113

JS

513

14R11

R 1511

C001

1R11 6

C 020

C 030

2C3 73

C11

40

27Q3 0

C 4111

C0

05

27Q3 1

C1 421

C0

06

D5

83

C008

JS

520

JS

521

2R11 2

JS

52

2

R 2311

JS

523

2R11 4

R3

25

9

R11

25

5JS 26

28C3 3

Q 2803

Q 2813

D1 301

D11

31

C4

01

D11

32

C402

L873

R 3011

C 044

3R11 1

C 054

R 3211

C4

06

C 074

R 3311

R 3411

C4

08

C 2903

C4

09

R1135

29C3 1

R11

36

C 2933

0C6 1C602

0C6 3

D11

40

C 046

C605

C 066

2R3 72

C607

R11

40

C608

R1141

2R3 75

C 096

4R11 2

27R3 6

R 2773

27R3 8

C 106

C611

C612

1C6 3

C614

A5

C6

15

R3282C

61

8

JS

550

C619

R3285

2R3 86

R 287328R3 8

JS

557

C 206

21C6

C6

22

2C6 3

2C6 5

R3

29

2R

32

93

R857

JS

30

00

5JS 60

R 2943

5R8 8

2R3 95

JS

561

JS3001

18JS 1

3C6 1

C 336

JS184

JS

186

C636

72R6

R867

R8

68

R8

69

J 01S3 5

TPA

1

TP 2A

D002

3JS 016

TPA

3

D0

03

T 4PA

D005

Q101

Q 021

TPA

33

Q104

Q105

0Q1 7

12R2 0

0JS3 22

D0

11

02D4

0D4 3

0D4 4

JS3035

JS 0363

J 303S 7

JS 0383

JS 0393

C8

56

TPA

10

JS

30

41

JS

30

42

TPA

15

L 250

C8

63

C 706

67C8

C 688

L1

20

C8

69

TPA

21

L125

TPA

22

TPA

23

L5

10

TPA

24

TPA

25

L5

11

L512

L5

13

C680

IC601

IC 028

D630

1JS1 30

L3000

R 061

JS002

0R1 8

51Q5

R1

09

Q 525

R1 11

R1 21

R 611

R11

7

R11

8

R11

9

L3016

R5

03

JS

40

0

R504

L550

D8

52

R 075

R 201

R508

Q180

R509

R1

21

R1

22

R 231

24R1

IC451

R1

26

1R5 0

R 11512R5

R513

14R5

0JS6 4

L5

60

R515

R1

30

I 20C1 1

R 311

R1

32

33R1

R 341

L181

R 351

R1

36

R1

37

R5

20

Q580

3R1 8

4L18

R5

21

Q581

3R1 9

L1 58

R 225

L3037

2R5 3

R5

24

1JS6 4

R 255

C1

09

L3

04

1

R1

45

L3

04

2

C 011

R1

50

5R1 1

C11

6

C1 71

C502

0C5 3

C5

04

C 065

20C1

C 211

JK

3002

C 221

JK

3003

23C1

11C5

C514

15C5

C 165

R 535

R554

1C5 9

C1

31

32C1

R5

57

C 331

R 585

C 351

5R5 9

3C1 6

R1

73

2C5 0

60R5

R 615

62R5

63R5

R 851

R 861

R1

87

R 901

01Q0

1DY

R5

80

6JS 70

JS

867

R 835

R 845

86R5

R 875

R588

08D1

C552

JS

87

3

C555

91R5

L0

01

L 200

R5

92

R5

93

Q 004

58C5

R5

94

9R5 5

C1

72

8JS 82

8JS8 3

C 655

C5

66

D 201

C180

L4

00

C 705

11D5

D5

12

1D5 3

D5

15

C 911

8C5 0

02C3 0

D5

20

C 0213

8C5 1

E

C 0283

C 905

0Q3 30

C3037

L620

01R3 0

0C3 39

0R3 12

0R3 13

R3014

0R3 15

A 21

R 0183

C 0111

R 030

0R0 4

R0

06

R 070

08R0

02R3 2

51D5

11R0

R0

12

D 525

J 02S1

JS 031

Q11

10

55D5

5D5 6

D557

T4A

L

2JS3 96

32JS 61

J 329S 7

26R3 7

26R3 8

2R3 66

2C3 69

R 2653

R 2613

Q 2613

Q 2623

Q3260

2R3 62

2R3 64

R 124

R4

13

JS

413

R4

11

C 034

R 122 2

12R2 1

C 1203

15C3 1

IC3

15

1

1C3 55

C3153

31JS 29

R 1493

D8

73

D 728

R564

A8

2C3 63

JA1

J 3A

JA4

5JA

J 6A

7JA

J 8A

9JA

DIP

Q 1202

Q103

Q 205

JS524

JS

525

C5

61

01X6

1X2 30

2R3 89

R 2793

C3038

JK

3102

R A

C3036

80

A

A

XF

102

LF

801

Q501

X182

X1

84

X183

X 801

JS2311L 1123

D5

84

C 135

C 178

R8

40

13R3 3

JS

31

38

JS

3139

JS

41

5

JS

41

6

B

B

L501

C562

T553

C8

22

R8

51

C821

55R5

XF

10

1

FL 2903

FL

32

91

CF

804

JA

11

R5

81

R8

70

2JA1

R685

R 965

Q8

55

Q853

5R8 4

Q8

54

C2

30

7

JS

1103

R 0311

RL

80

1

JA

10

TU

00

1

T5

01

C

C

D

81X1

D8

21

C841

0T8 1

63R8

R850

JS120

C5

67

C854

0C8 1

C8

02

L1

58

C559

C 118

C8

40

C857

C1120

C0

04

C5

60

01R8

C11

10

C11

11

C5

63

C568

PC

86

0

C8

42

C8

46

C845

C8

44

D365

IC351

D3

75

L350

L351

L3

52

Q369

L8

L1

0

L11

TP

L1

TP

L2

TP

L4

TPL5

TPL7

R351

R352

R353

R357

R358

R3

59

R363

R364

R3

65

R3

69

R3

74

SC

35

1

C3

50

C359

C3

68

C370

C3

71

C3

73

C3

77

C971

D354

D355

D356

D360

D361

D362

D363

L5

1

1

2

2

3

3

2

1

4

4

2

3

1

12

34

HO

T

CH

CH

LVO +

TV

/AV

PRESET

VO

L-

LIV

EC

IRC

UIT

OBR WN

UBL E

PbF

4 3

1

6

2

23

3

12

3

32

1

4

5

6

7

8

9

11

11A

H.V

.DA

NG

ER

CO

LD

10

1

1

TN

P4G

347

A3

1 2

34

1

2

PbF

NC

CB

H+

H-

CR

CG

G2

CG

G1

H-

CB

H+

G1

CRCG

TN

P4

G3

48

H.V

.DAN

GER

3L

BE

C

EB C

V

12

1 2

1

12

1

6

3

7

5

4

1

2

67

9

1

12 3

14

1

4 5

8

24

25

4041

65

64

1

SE

ER

EV

ER

SE

FOR

OR

DE

RN

O.

1

2425

40

41

64

65

80

13

2

E

C

B

126

7

1

34

6

1 4

1

4

145

8

1

6

16

EBC

1

5

+

-

15

MB SC

L

SD

A

IF1 AG

C

AS

SD

A

TU2

IFO

UT TU

AD

D

VS

UP

PLY

BTL

V2V1P2PTP1

S5 S6 S1S2 S3

1

28

9

SE

ER

EV

ER

SE

FOR

OR

DE

RN

O.

8

1

6

1

6

- 21 -

TC-20KL05P

Pino 16 Pino 17

Pino 1

Pino 5

Pino 3

Pino 7I C 6 0 1

SIGNAL WAVEFORM• All waveforms were obtained using 127V 60Hz power source and Color Bars Pattern.

IC451

- 22 -

TC-20KL05P

Pino 42 Pino 55

IC601

Pino 18 Pino 19

Pino 38 Pino 40

- 23 -

TC-20KL05P

Pino 64

IC601

Pino 56 Pino 57

Pino 58 Pino 63

- 24 -

TC-20KL05P

Pino 1

IC801

Base

Q501

Coletor

Coletor

Q551

Emissor

Q601

Coletor

Q602

- 25 -

TC-20KL05P

EXPLODED VIEW5

32

32

- 26 -

TC-20KL05P

1 EASZ12D06B FULL RANGE SPEAKER 5W 8Ω2 TLK2B20001A DEGAUSSING COIL

3 TBX2B867 POWER BUTTON

4 TBX2B865 6 POSITIONS BUTTON

5 TSA8108-6KP TELESCOPIC ANTENNA

6 TMW2B212-1 BRACKET LED

7 TSX2BA06 AC CABLE (URUGUAY)

7 TSX2BA07 AC CABLE (PANALAT)

8 EVQ11G05R TOUCH SWITCHES

9 ESB92DA1B POWER SWITCH

1 1 A48EAK01X094R PICTURE TUBE

1 3 TNQ2B2801-1 REMOTE CONTROLLER

1 4 S-U5012 ADAPTOR BALLUM 300Ω / 75Ω1 5 TBM2B412 PANASONIC LOGO

1 6 TMM2B405 DEGAUSSING COIL HOLDER

1 7 TKP2B11161-2 AC CABLE HOLDER

1 8 EXP-TKY2B2003-5 FRONT CABINET

1 9 TKP2B11291 LED GUIDE

2 0 TMK2B564 HIMERON

2 1 TXF3A20C7-1 COIL SPRING

2 2 TQB2B0149 OPERATING INSTRUCTIONS

2 3 TES2B212 POWER BUTTON SPRING

2 4 TBM2B047-3 CONTROL PANEL

2 5 PAL20KL05PMON ASSEMBLED P.C.B.

2 8 TKP2B11271 DOOR

2 9 TKK2B9524 POWER SWITCH EXTENSOR

3 0 K3B095A00001 CRT 20" SOCKET

3 1 TKX2B1301 SPEAKER SUPPORT

3 2 TKX2B0601 REAR COVER SUPPORT

3 3 TKU2B23103 REAR COVER

3 4 ZTFPIZ504A FLYBACK

3 5 TEK4G902 DOOR LOCK

3 7 K4BK09B00010 AV TERMINAL ( 6 PINS - RCA)

3 8 K4BC14B00004 FRONTAL AV TERMINAL

REF. Nº Part Name & DescriptionPart Nº

REPLACEMENT MECHANICAL PARTS LIST

- 27 -

TC-20KL05P

Ref. No. Part No. Part Name & Description

MAIN P.C.B.PAL20KL05PMON ASSEMBLED P.C.B. “A + L“

CAPACITORC001 F2A1C220A147 ELECTROLYTICAL CAP. 22µF 16VC002 ECJ2VF1C104Z CERAMIC CAP. SMD 100nF 16VC003 ECJ2VF1C104Z CERAMIC CAP. SMD 100nF 16VC006 F2A0J221A181 ELECTROLYTICAL CAP. 220µF 6,3VC008 F2A1H1R0A145 ELECTROLYTICAL CAP. 1µF 50VC117 ECJ2VB1H103J CERAMIC CAP. SMD 10nF 50VC180 ECJ2VC1H151J CERAMIC CAP. SMD 150PF 50VC191 F1J1H104A717 CERAMIC CAP. SMD 100nF 50VC193 F2A1C100A180 ELECTROLYTICAL CAP. 10µF 16VC350 F2A1C101A180 ELECTROLYTICAL CAP. 100µF 16VC359 ECQE2104KFB POLYESTER CAP. 0,10 µF 250VC368 ECJ2VC1H122J CERAMIC CAP. SMD 1,20 nF 50VC370 ECKW3D102KBP CERAMIC CAP. 1nF 2.000VC371 ECEA1CN100UB ELECTROLYTICAL CAP. 10µF 16VC373 F2A2E1000011 ELECTROLYTICAL CAP. 10µF 250VC377 F2A1C4710045 ELECTROLYTICAL CAP. 470µF 16VC402 ECA1VM101B ELECTROLYTICAL CAP. 100µF 35VC404 ECQB1333JF3 POLYESTER CAP. 33nF 100VC406 F2A1H221A247 ELECTROLYTICAL CAP. 220µF 50VC407 ECQB1H103JF3 POLYESTER CAP. 10nF 50VC408 ECQB1274JF3 POLYESTER CAP. 270nF 100VC502 F1B2H821A025 CERAMIC CAP. 820PF 500VC503 F1B2H821A025 CERAMIC CAP. 820PF 500VC504 ECJ2VB1H681K CERAMIC CAP. SMD 680PF 50VC506 F1A2H1000002 CERAMIC CAP. 10PF 500,0 V 0,50 PFC511 ECA1VM101B ELECTROLYTICAL CAP. 100µF 35VC513 ECKW3D331JBP CERAMIC CAP. 330PF 2.000VC514 F2A1E102A151 ELECTROLYTICAL CAP. 1.000µF 25VC515 F1B2H331A025 CERAMIC CAP. 330PF 500VC516 F2A1E102A151 ELECTROLYTICAL CAP. 1.000µF 25VC519 F2A2C330A096 ELECTROLYTICAL CAP. 33µF 160VC520 F2A0J221A181 ELECTROLYTICAL CAP. 220µF 6,3VC552 F2A2E1000011 ELECTROLYTICAL CAP. 10µF 250VC555 F1B2H471A025 CERAMIC CAP. 470PF 500VC558 ECQB1104JF3 POLYESTER CAP. 100nF 100VC559 ECWH16103JVB CAPACITOR POLIPROP. 10nF 1.600VC560 ECQM4333JZW POLYESTER CAP. 33nF 400VC561 ECKW3D151KBR CERAMIC CAP. 150PF 2.000VC562 ECKW3D821JBR CERAMIC CAP. 0,82 nF 2.000VC563 ECWF2394JSR CAPACITOR POLIPROP. 390nF 250VC565 ECQP1H183JZ3 CAPACITOR POLIPROP. 18nF 50VC570 ECJ2VC1H330J CERAMIC CAP. SMD 33PF 50VC580 F2A1H220A162 ELECTROLYTICAL CAP. 22µF 50VC581 ECJ2VF1C105Z CERAMIC CAP. SMD 1µF 16,0 VC601 F2A1C101A180 ELECTROLYTICAL CAP. 100µF 16VC602 F1J1H104A717 CERAMIC CAP. SMD 100nF 50VC603 ECJ2VB1H472K CERAMIC CAP. SMD 4.700PF 50VC604 ECQV1H224JL3 POLYESTER CAP. 220nF 50VC605 ECQV1H224JL3 POLYESTER CAP. 220nF 50VC606 ECJ2VC1H222J CERAMIC CAP. SMD 2.200PF 50VC607 F2A1H1R0A145 ELECTROLYTICAL CAP. 1µF 50VC608 F2A1H100A145 ELECTROLYTICAL CAP. 10µF 50VC609 F1J1H104A717 CERAMIC CAP. SMD 100nF 50VC610 ECJ2VB1H103J CERAMIC CAP. SMD 10nF 50VC612 ECJ2VB1H472K CERAMIC CAP. SMD 4.700PF 50VC613 ECJ2VB1H472K CERAMIC CAP. SMD 4.700PF 50VC614 ECQV1H104JL3 POLYESTER CAP. 100nF 50VC615 ECQV1H224JL3 POLYESTER CAP. 220nF 50VC619 ECQV1H104JL3 POLYESTER CAP. 100nF 50VC620 ECJ2VC1H330J CERAMIC CAP. SMD 33PF 50VC621 ECJ2VF1C105Z CERAMIC CAP. SMD 1µF 16,0 VC622 ECJ2VF1H104Z CERAMIC CAP. SMD 100nF 50,0 VC623 ECJ2VC1H330J CERAMIC CAP. SMD 33PF 50VC625 F2A0J221A181 ELECTROLYTICAL CAP. 220µF 6,3VC628 ECJ2YB1H473K CERAMIC CAP. SMD 47nF 50VC633 ECJ2VF1C105Z CERAMIC CAP. SMD 1µF 16,0 VC636 F2A1C101A180 ELECTROLYTICAL CAP. 100µF 16V

Ref. No. Part No. Part Name & Description

C640 F2A1C100A180 ELECTROLYTICAL CAP. 10µF 16VC641 ECJ2VC1H100C CERAMIC CAP. SMD 10PF 50,0 VC670 F2A1C100A180 ELECTROLYTICAL CAP. 10µF 16VC680 ECJ2YB1H473K CERAMIC CAP. SMD 47nF 50VC685 ECJ2VC1H101K CERAMIC CAP. SMDC686 ECJ2YB1H473K CERAMIC CAP. SMDC687 ECJ2VF1H104Z CERAMIC CAP. SMD 100nF 50,0 VC689 ECJ2VF1H104Z CERAMIC CAP. SMD 100nF 50,0 VC801 ECQU2A224BN9 POLYPROPILENE CAPACITOR 220nF 100,0 VC802 ECQU2A224BN9 POLYPROPILENE CAPACITOR 220nF 100,0 VC806 ECKWAE472ZED CERAMIC CAP. 4,7 nF 250VC807 ECKWAE472ZED CERAMIC CAP. 4,7 nF 250VC808 ECKWAE472ZED CERAMIC CAP. 4,7 nF 250VC809 ECKWAE472ZED CERAMIC CAP. 4,7 nF 250VC810 EETHC2G181H ELECTROLYTICAL CAP. 180µF 400VC811 ECQM4473JZW POLYESTER CAP. 47nF 400VC816 F2A1H3300037 ELECTROLYTICAL CAP. 33µF 50VC819 F2A1H1R0A162 ELECTROLYTICAL CAP. 1µF 50VC821 ECKW3D471KBR CERAMIC CAP. 470PF 2.000VC822 ECKW3D331JBR CERAMIC CAP. 330PF 2.000VC825 ECQB1H471JF3 POLYESTER CAP. 470PF 50VC826 F0A1H103A039 POLYPROPILENE CAPACITOR 0,01 µF 50VC827 ECQB1H683JF3 POLYESTER CAP. 68PF 50VC830 ECQB1H102JF3 POLYESTER CAP. 1nF 50VC840 F1A2E471A002 CERAMIC CAP. 470PF 250VC841 ECKCNA102MB7 CERAMIC CAP. 1.000PF 250VC842 F1A2E102A001 CERAMIC CAP. 1.000PF 250VC844 ECKCNA222ME7 CERAMIC CAP. 2,20 nF 4.000VC846 F1A2E101A002 CERAMIC CAP. 100PF 250VC850 ECJ2VF1H224Z CERAMIC CAP. SMD 220nF 50,0 VC853 F1B2H561A025 CERAMIC CAP. 560PF 500VC854 ECKW3D821KBP CERAMIC CAP. 820PF 2.000VC855 F1B2H331A025 CERAMIC CAP. 330PF 500VC856 F2A1C100A180 ELECTROLYTICAL CAP. 10µF 16VC862 F2A1C332A232 ELECTROLYTICAL CAP. 3.300µF 16VC863 F2A2C680A022 ELECTROLYTICAL CAP. 68µF 160VC864 F2A1C102A252 ELECTROLYTICAL CAP. 1.000µF 16VC875 F2A1C101A180 ELECTROLYTICAL CAP. 100µF 16VC876 F2A1C101A180 ELECTROLYTICAL CAP. 100µF 16VC877 F2A1A471A161 ELECTROLYTICAL CAP. 470µF 10VC879 ECQV1H104JL3 POLYESTER CAP. 100nF 50VC880 F2A1C1020049 ELECTROLYTICAL CAP. 1.000µF 16VC881 F2A1C101A180 ELECTROLYTICAL CAP. 100µF 16VC882 ECJ2VF1H104Z CERAMIC CAP. SMD 100nF 50,0 VC883 ECJ2VF1H104Z CERAMIC CAP. SMD 100nF 50,0 VC971 ECJ2VF1H103Z CERAMIC CAP. SMD 10nF 50,0 VC1101 ECJ2VF1C104Z CERAMIC CAP. SMD 100nF 16VC1103 ECJ2VC1H331J CERAMIC CAP. SMD 330PF 50VC1104 F2A1C101A180 ELECTROLYTICAL CAP. 100µF 16VC1105 ECJ2VF1C104Z CERAMIC CAP. SMD 100nF 16VC1120 ECJ2VF1H103Z CERAMIC CAP. SMD 10nF 50,0 VC1125 F2A1C100A147 ELECTROLYTICAL CAP. 10µF 16VC1130 ECJ2VC1H560J CERAMIC CAP. SMD 56PF 50VC1131 F2A0J221A181 ELECTROLYTICAL CAP. 220µF 6,3VC1132 ECJ2VC1H560J CERAMIC CAP. SMD 56PF 50VC1140 F2A1C101A180 ELECTROLYTICAL CAP. 100µF 16VC1141 ECJ2VF1C104Z CERAMIC CAP. SMD 100nF 16VC1142 ECJ2VF1C104Z CERAMIC CAP. SMD 100nF 16VC2101 F2A1C101A180 ELECTROLYTICAL CAP. 100µF 16VC2102 ECJ2VF1C104Z CERAMIC CAP. SMD 100nF 16VC2103 ECJ2VF1C105Z CERAMIC CAP. SMD 1µF 16,0 VC2104 ECJ2VF1C105Z CERAMIC CAP. SMD 1µF 16,0 VC2105 ECJ2VF1C105Z CERAMIC CAP. SMDC2106 ECJ2VF1C105Z CERAMIC CAP. SMDC2109 F2A1C100A180 ELECTROLYTICAL CAP. 10µF 16VC2110 ECJ2VB1H332K CERAMIC CAP. SMD 3,30 nF 50VC2111 ECJ2VB1H332K CERAMIC CAP. SMD 3,30 nF 50VC2113 F2A1H4R7A182 ELECTROLYTICAL CAP. 4,70 µF 50VC2114 ECJ2VF1H104Z CERAMIC CAP. SMD 100nF 50,0 VC2115 F2A1H4R7A182 ELECTROLYTICAL CAP. 4,70 µF 50V

REPLACEMENT ELECTRICAL PARTS LIST

- 28 -

TC-20KL05P

Part No.

C2117 F2A1C101A180 ELECTROLYTICAL CAP. 100µF 16VC2120 F2A1H3R3A182 ELECTROLYTICAL CAP. 3,30 µF 50VC2121 ECJ2VF1C104Z CERAMIC CAP. SMD 100nF 16VC2124 F2A1C100A180 ELECTROLYTICAL CAP. 10µF 16VC2125 ECJ2VF1C105Z CERAMIC CAP. SMD 1µF 16,0 VC2127 ECJ2VF1C104Z CERAMIC CAP. SMD 100nF 16VC2128 F2A1C101A180 ELECTROLYTICAL CAP. 100µF 16VC2133 ECJ2VC1H070D CERAMIC CAP. SMD 7PF 50,0 V 0,50 PFC2134 ECJ2VC1H470J CERAMIC CAP. SMD 47PF 50VC2135 ECJ2VC1H560J CERAMIC CAP. SMD 56PF 50VC2136 ECJ2VC1H560J CERAMIC CAP. SMD 56PF 50VC2137 ECJ2VC1H560J CERAMIC CAP. SMD 56PF 50VC2138 ECJ2VC1H470J CERAMIC CAP. SMD 47PF 50VC2139 ECJ2VC1H040C CERAMIC CAP. SMD 4PF 50,0 V 0,25 PFC2140 ECJ2VC1H040C CERAMIC CAP. SMD 4PF 50,0 V 0,25 PFC2141 ECJ2VF1C105Z CERAMIC CAP. SMD 1µF 16,0 VC2142 ECJ2VF1C105Z CERAMIC CAP. SMD 1µF 16,0 VC2151 ECJ2VC1H331J CERAMIC CAP. SMD 330PF 50VC2152 ECJ2VF1H103Z CERAMIC CAP. SMD 10nF 50,0 VC2302 F2A1E471A151 ELECTROLYTICAL CAP. 470µF 25VC2303 F2A1C101A180 ELECTROLYTICAL CAP. 100µF 16VC2304 ECEA1HKN0R1B ELECTROLYTICAL CAP. BIPOLAR 0,10 µF 50VC2305 ECEA1HKN0R1B ELECTROLYTICAL CAP. BIPOLAR 0,10 µF 50VC2306 F2A1H100A162 ELECTROLYTICAL CAP. 10µF 50VC2380 F2A1C101A180 ELECTROLYTICAL CAP. 100µF 16VC2381 F2A1C100A180 ELECTROLYTICAL CAP. 10µF 16VC3020 ECJ2VB1H392K CERAMIC CAP. SMD 3.900PF 50VC3021 F2A1C4710045 ELECTROLYTICAL CAP. 470µF 16VC3028 ECJ2VF1C105Z CERAMIC CAP. SMD 1µF 16,0 VC3036 ECJ2VB1H392K CERAMIC CAP. SMD 3.900PF 50VC3037 ECJ2VF1C105Z CERAMIC CAP. SMD 1µF 16,0 VC3136 ECJ2VF1H103Z CERAMIC CAP. SMDC3137 ECJ2VF1H103Z CERAMIC CAP. SMDC3138 F2A1C100A180 ELECTROLYTICAL CAPACITORC3139 F2A1C100A180 ELECTROLYTICAL CAPACITORC3143 ECJ2VB1H392K CERAMIC CAP. SMDC3144 ECJ2VB1H392K CERAMIC CAP. SMDPOSISTORCF804 TAP4GA0005 POSISTOR 12,0 ΩCONNECTORSA12 K1KA04AA0190 CONNECTORA22 BJP11V04-AP CONNECTORA22-SPK TXAJTA22CB20K-1 CONNECTORA4-1 TEL376 CONNECTORA4-2 TEL376 CONNECTORA6-1 TEL376 CONNECTORA6-2 TEL376 CONNECTORJK3002 K4BK09B00010 CONNECTORJK3102 K4BC14B00004 CONNECTORL5~A5 TXAJTA5CB14A12 CONNECTORL8~A8 TXAJTA8CB29K CONNECTORSC351 K3B095A00001 CRT SOCKETDIODESD002 B0BA01700031 ZENER DIODE 17,0 V 0,5 W 5,0 mA RZ = 20ΩD003 B0BA01500036 ZENER DIODE 15,0 V 0,5 W 5,0 mA RZ = 40ΩD011 B0ACQJ000001 SWITCHING DIODE 80,0 V 250,0 mAD354 B0ACQJ000001 SWITCHING DIODE 80,0 V 250,0 mAD355 B0ACQJ000001 SWITCHING DIODE 80,0 V 250,0 mAD356 B0ACQJ000001 SWITCHING DIODE 80,0 V 250,0 mAD360 B0HAMP000067 RECTIFIER DIODE 400,0 V 1,0 AD361 B0HAMP000067 RECTIFIER DIODE 400,0 V 1,0 AD362 B0HAMP000067 RECTIFIER DIODE 400,0 V 1,0 AD363 B0ACQJ000001 SWITCHING DIODE 80,0 V 250,0 mAD365 B0BA9R900005 ZENER DIODE 9,9 V 0,5 W 5,0 mAD375 B0ACQJ000001 SWITCHING DIODE 80,0 V 250,0 mAD402 B0HAHM000008 RECTIFIER DIODE 200,0 V 0,6 AD403 B0ACMJ000001 SWITCHING DIODE 80,0 V 1,0 AD404 B0ACMJ000001 SWITCHING DIODE 80,0 V 1,0 AD511 MAZ4108J0F ZENER DIODE 10,8 V 0,37 W 250,0 mAD512 MA2B17100E SWITCHING DIODE 200mA VRM=80VD513 B0HAJP000015 RECTIFIER DIODE 400,0 V 0,7 AD515 B0HAJP000015 RECTIFIER DIODE 400,0 V 0,7 AD520 B0ACQJ000001 SWITCHING DIODE 80,0 V 250,0 mA

D551 MAZ30470HL ZENER DIODE SMD VZ= 4,74 ~ 4,99 V AT IZ=5MAD552 B0HAJP000015 RECTIFIER DIODE 400,0 V 0,7 AD555 B0ACQJ000001 SWITCHING DIODE 80,0 V 250,0 mAD556 B0EAKV000008 RECTIFIER DIODE 1.000V 1,0 A VFM=1,2VD557 B0HAMR000073 RECTIFIER DIODE 600,0 V 1,0 AD558 B0AADM000003 SWITCHING DIODE 200V 0,2 A 1SS244T-77D583 B0ACQJ000002 SWITCHING DIODE 80,0 V 0,25 200,0 mAD584 B0BA5R600016 ZENER DIODE 5,6 V 0,5 W 5mA RZ = 100ΩD801 ERZV10V621CS VARISTORD803 B0EBNT000007 RECTIFIER DIODE 800,0 V 4,0 AD810 B0EAKT000018 RECTIFIER DIODE 800V 1A TAPING = 26 MMD817 B0HAJL000001 RECTIFIER DIODE 100,0 V 0,7 AD821 MAZ20750A0LS ZENER DIODE 7,2 V 1/2 W RZ < 10 ΩD823 B0HAJL000001 RECTIFIER DIODE 100,0 V 0,7 AD824 B0HAJL000001 RECTIFIER DIODE 100,0 V 0,7 AD825 B0BA6R100043 ZENER DIODE 6,1 V 0,5 W 5,0 mAD830 B0HAJL000001 RECTIFIER DIODE 100,0 V 0,7 AD831 B0BA02400029 ZENER DIODE 24,0 V 0,5 W 5,0 mA RZ = 20ΩD850 B0ACMJ000001 SWITCHING DIODE 80,0 V 1,0 AD852 B0ACMJ000001 SWITCHING DIODE 80,0 V 1,0 AD853 B0HAMM000108 RECTIFIER DIODE 200,0 V 1,5 AD854 B0HAPV000009 RECTIFIER DIODE 1.000,0 V 3,0 AD855 B0HFRJ000012 RECTIFIER DIODE 80,0 V 5,0 AD856 B0BA7R400019 ZENER DIODE 7,4 V 0,5 W 5,0 mAD862 B0BA2R100016 ZENER DIODE 2,1 V 0,5 W 5,0 mA RZ = 20ΩD863 B0HAJL000001 RECTIFIER DIODE 100,0 V 0,7 AD865 B0BA3R500006 ZENER DIODE 3,5 V 0,5 W 5,0 mAD870 B0HAJL000001 RECTIFIER DIODE 100,0 V 0,7 AD871 B0HAJL000001 RECTIFIER DIODE 100,0 V 0,7 AD873 B0BA8R200005 ZENER DIODE 8,2 V 0,5 W 5mA VZ=8,03~8,45VD1105 B0BA7R500006 ZENER DIODE 7,5 V 1/2 W 5,0 mA RZ = 10ΩD1120 B0ACQJ000001 SWITCHING DIODE 80,0 V 250,0 mAD1130 B0BA5R700008 ZENER DIODE 5,7 V 0,5 W 5,0 mA RZ = 40ΩD1131 B0BA5R700008 ZENER DIODE 5,7 V 0,5 W 5,0 mA RZ = 40ΩD1132 B0BA5R400008 ZENER DIODE 5,4 V 1/2 W 5,0 mA RZ = 40ΩD1140 B0BA5R600016 ZENER DIODE 5,6 V 0,5 W 5,0 mA RZ = 100ΩD1151 EL333ID/S928 DIODO LED RADIAL 5,0 V 1/10 WD2380 B0ACQJ000001 SWITCHING DIODE 80,0 V 250,0 mAD2381 B0ACQJ000001 SWITCHING DIODE 80,0 V 250,0 mAD2382 B0ACQJ000001 SWITCHING DIODE 80,0 V 250,0 mAFUSEF801 K5D402BK0004 FUSEF801-L EYF52BCY FUSE HOLDERF801-R EYF52BCY FUSE HOLDERINTEGRATED CIRCUITSIC451 AN15525A INTEGRATED CIRCUITIC601 TDA9540N48CH INTEGRATED CIRCUITIC801 C5HABZZ00116 INTEGRATED CIRCUITIC802 C0EAS0000026 VOLTAGE DETECTOR ICIC851 C0DAAHF00005 VOLTAGE REGULATOR ICIC880 AN77L05-TA VOLTAGE REGULATOR ICIC1103 C3EBFC000042 EEPROM MEMORY ICIC1201 C0CBABC00160 VOLTAGE REGULATOR ICIC2101 C1AB00001960 AUDIO PROCESSOR ICIC2301 AN7522N INTEGRATED CIRCUITPC860 B3PAA0000261 PHOTO COUPLER ICRM1104 B3RAC0000014 REMOTE CONTROL RECEPTOR ICJUMPERSE - A B3B0C223PT210T JUMPERB - B TXAJTFFCB14A12 JUMPERJA1 ERJ6GEY0R00V RESISTOR 0Ω 1/8 WJA3 ERJ6GEY0R00V RESISTOR 0Ω 1/8 WJA4 ERJ6GEY0R00V RESISTOR 0Ω 1/8 WJA5 ERJ6GEY0R00V RESISTOR 0Ω 1/8 WJA7 ERJ6GEY0R00V RESISTOR 0Ω 1/8 WJA8 ERJ6GEY0R00V RESISTOR 0Ω 1/8 WJA9 ERJ6GEY0R00V RESISTOR 0Ω 1/8 WJA10 ERJ6GEY0R00V RESISTOR 0Ω 1/8 WJA12 ERJ6GEY0R00V RESISTOR 0Ω 1/8 WJS102 ERJ6GEY0R00V RESISTOR 0Ω 1/8 WJS110 ERJ6GEY0R00V RESISTOR 0Ω 1/8 WJS111 ERJ6GEY0R00V RESISTOR 0Ω 1/8 WJS112 ERJ6GEY0R00V RESISTOR 0Ω 1/8 W

Ref. No. Part No. Part Name & Description Ref. No. Part Name & Description

- 29 -

TC-20KL05P

JS113 ERJ6GEY0R00V RESISTOR 0Ω 1/8 WJS122 ERJ6GEY0R00V RESISTOR 0Ω 1/8 WJS415 ERJ6GEY0R00V RESISTOR 0Ω 1/8 WJS2140 ERJ6GEY0R00V RESISTOR 0Ω 1/8 WJS2141 ERJ6GEY0R00V RESISTOR 0Ω 1/8 WJS3001 ERJ6GEY0R00V RESISTOR 0Ω 1/8 WJS3138 ERJ6GEY0R00V RESISTOR 0Ω 1/8 WJS3139 ERJ6GEY0R00V RESISTOR 0Ω 1/8 WCOILSL001 G0C100K00008 COIL 10µHL002 EXC3BB221H COIL (BEAD CORE) Z=200 Ω (100MHZ); I= 0,2 AL182 TALV35VB6R8K COIL 6,80 µH I=0,4AL185 G0C100JA0021 COIL 10µHL352 J0JKA0000022 COIL (BEAD CORE) I=6 A / Z= 60Ω( 100MHZ)L511 J0JKA0000038 COIL (BEAD CORE) Z=80Ω (100 MHZ); I=6AL550 J0JKB0000038 COIL (BEAD CORE) RADIAL I=6 A / Z= 100Ω ( 100MHZ)L620 J0JCC0000009 COIL (BEAD CORE) 200MA, 2,25KΩL820 J0JKA0000025 COIL (BEAD CORE) Z=80Ω (100 MHZ); I=6AL821 J0JKA0000038 COIL (BEAD CORE) Z=80Ω (100 MHZ); I=6AL852 J0JKA0000023 COIL (BEAD CORE) Z=80Ω (100MHZ); I= 6 AL853 J0JKA0000025 COIL (BEAD CORE) Z=80Ω (100 MHZ); I=6AL854 J0JKA0000023 COIL (BEAD CORE) Z=80Ω (100MHZ); I= 6 AL862 G0C1R5KA0030 COIL 1,50 µHL871 G0C1R5KA0030 COIL 1,50 µHL872 G0C1R5KA0030 COIL 1,50 µHL873 J0JKA0000024 COIL (BEAD CORE) I=6 A / Z= 100Ω ( 100MHZ)L1101 TALV35VB331K COIL 330µH I=0,4AL2104 G0C330JA0021 COIL 33µHL2107 G0C100JA0021 COIL 10µHL2130 G0C330JA0021 COIL 33µHL2132 G0C180KA0065 COIL 18µHL2133 J0JKB0000034 COIL I = 6 A / Z=100 Ω (100MHZ)L3136 J0JKA0000038 COIL (BEAD CORE) Z=80Ω (100 MHZ); I=6AL3137 J0JKA0000038 COIL (BEAD CORE) Z=80Ω (100 MHZ); I=6ALF801 ELF21V012S COIL FILTER 25mHTRANSISTORSQ001 B1ABCE000015 NPN TRANSISTOR 0,2W 200,0 mAQ369 B1ADDF000005 PNP TRANSISTOR 0,2 W 50V 200mAQ400 B1ABCE000015 NPN TRANSISTOR 0,2W 200,0 mAQ501 2SC4212H00LB NPN POWER TRANSISTOR BIPOLAR 1W 300VQ520 2SB792ATX PNP TRANSISTOR 0,2 W 185V 50mAQ551 2SC5902000LK NPN TRANSISTOR 1.000,0 V 8,0 AQ580 B1ABCE000015 NPN TRANSISTOR 0,2W 200,0 mAQ581 B1ADDF000005 PNP TRANSISTOR 0,2 W 50V 200mAQ601 B1ADDF000005 PNP TRANSISTOR 0,2 W 50V 200mAQ602 B1ABCE000015 NPN TRANSISTOR 0,2W 200,0 mAQ852 B1ABCE000015 NPN TRANSISTOR 0,2W 200,0 mAQ853 B1ADCE000012 PNP TRANSISTOR 0,1 W 50V 100mAQ854 B1ABCE000015 NPN TRANSISTOR 0,2W 200,0 mAQ855 B1ADCE000012 PNP TRANSISTOR 0,1 W 50V 100mAQ857 B1BAAN000029 NPN TRANSISTOR 1 300,0 V 1,0 AQ870 B1ABCE000015 NPN TRANSISTOR 0,2W 200,0 mAQ871 B1ABCE000015 NPN TRANSISTOR 0,2W 200,0 mAQ1053 B1ABCE000015 NPN TRANSISTOR 0,2W 200,0 mAQ1110 B1ADDF000005 PNP TRANSISTOR 0,2 W 50V 200mAQ1130 B1ABCE000015 NPN TRANSISTOR 0,2W 200,0 mAQ2110 B1ADDF000005 PNP TRANSISTOR 0,2 W 50V 200mAQ2111 B1ADDF000005 PNP TRANSISTOR 0,2 W 50V 200mAQ2151 B1ABCE000015 NPN TRANSISTOR 0,2W 200,0 mAQ2380 B1ABCE000015 NPN TRANSISTOR 0,2W 200,0 mAQ2381 B1ADDF000005 PNP TRANSISTOR 0,2 W 50V 200mAQ3030 B1ABCE000015 NPN TRANSISTOR 0,2W 200,0 mARESISTORSR003 D0GD100JA017 RESISTOR 10Ω 1/8WR004 ERG3FJ183H RESISTOR 18kΩ 3WR006 D0GD273JA017 RESISTOR 27kΩ 1/8WR007 D0GD472JA017 RESISTOR 4,70 kΩ 1/8WR008 D0GD681JA017 RESISTOR 680Ω 1/8WR011 D0GD103JA017 RESISTOR 10kΩ 1/8WR012 D0GD332JA017 RESISTOR 3,30 kΩ 1/8WR021 D0GD273JA017 RESISTOR 27kΩ 1/8WR022 D0GD473JA017 RESISTOR 47kΩ 1/8WR182 D0GD221JA017 RESISTOR 220Ω 1/8W

R186 D0GD471JA017 RESISTOR 470Ω 1/8WR187 D0GD221JA017 RESISTOR 220Ω 1/8WR190 D0GD391JA017 RESISTOR 390Ω 1/8WR351 ERJ6ENF1001V RESISTOR 1kΩ 1/10R352 ERJ6ENF1001V RESISTOR 1kΩ 1/10WR353 ERJ6ENF1001V RESISTOR 1kΩ 1/10WR357 D0GD103JA017 RESISTOR 10kΩ 1/8WR358 D0GD333JA017 RESISTOR 33kΩ 1/8WR359 D0GD273JA017 RESISTOR 27kΩ 1/8WR363 ERC12GK222V RESISTOR 2,20 kΩ 1/2WR364 ERC12GK222V RESISTOR 2,20 kΩ 1/2WR365 ERC12GK222V RESISTOR 2,20 kΩ 1/2WR369 D0GD103JA017 RESISTOR 10kΩ 1/8WR374 ERQ12AJ181P FUSISTOR 180Ω 1/2WR401 D0AE104JA046 RESISTOR 100kΩ 1/4WR402 D0GD470JA017 RESISTOR 47Ω 1/8WR403 EROS2THF2491 RESISTOR 2,49 kΩ 0,25 WR404 D0AE751JA046 RESISTOR 750Ω 1/4WR405 EROS2THF2701 RESISTOR 2,70 kΩ 0,25WR406 ERDS1FJ1R0T RESISTOR 1Ω 1/2WR407 ERG2FJ331H RESISTOR 330Ω 2WR409 D0GD512JA017 RESISTOR 5,10 kΩ 1/8WR410 D0GD202JA017 RESISTOR 2kΩ 1/8WR414 D0GD432JA017 RESISTOR 4,30 kΩ 1/8WR415 EROS2THF7500 RESISTOR 750Ω 0,25WR416 ERDS1TJ1R2T RESISTOR 1,20 Ω 1/2WR417 ERDS1TJ1R2T RESISTOR 1,20 Ω 1/2WR502 D0GD182JA017 RESISTOR 1,80 kΩ 1/8WR504 ERG2SJ682E RESISTOR 6,80 kΩR507 D0GD101JA017 RESISTOR 100Ω 1/8WR508 ERG3FJ152H RESISTOR 1,50 kΩ 3WR509 ERG3FJ182H RESISTOR 1,80 kΩ 3WR511 ERJ6ENF1002V RESISTOR 10kΩ 1/10WR512 ERJ6ENF1182V RESISTOR 11,80 kΩ 1/10WR513 ERQ14AJ100E FUSISTOR 10Ω 1/4WR520 ERQ12AJ2R7E FUSISTOR 2,70 Ω 1/2WR521 ERQ12AJ2R7E FUSISTOR 2,70 Ω 1/2WR522 ERJ6GEYJ123V RESISTOR 12kΩ 1/8WR523 D0GD103JA017 RESISTOR 10kΩ 1/8WR524 D0GD104JA017 RESISTOR 100kΩ 1/8WR525 D0GD392JA017 RESISTOR 3,90 kΩ 1/8WR553 D0GD223JA017 RESISTOR 22kΩ 1/8WR554 ERJ6GEYJ103V RESISTOR 10kΩ 1/8WR555 ERQ14AJ2R0P FUSISTOR 2Ω 1/4WR557 ERO50PKF1473 RESISTOR 147kΩ 1/2WR558 D0AE513JA046 RESISTOR 51kΩ 0,25WR559 ERQ1CJP4R7S FUSISTOR 4,70 Ω 1WR564 D0AE393JA046 RESISTOR 39kΩ 1/4WR580 D0GD392JA017 RESISTOR 3,90 kΩ 1/8WR581 ERJ6GEYJ332V RESISTOR 3,30 kΩ 1/8WR583 D0GD274JA017 RESISTOR 270kΩ 1/8WR584 D0GD563JA017 RESISTOR 56kΩ 1/8WR586 D0GD103JA017 RESISTOR 10kΩ 1/8WR587 D0GD823JA017 RESISTOR 82kΩ 1/8WR588 D0GD104JA017 RESISTOR 100kΩ 1/8WR591 D0GD103JA017 RESISTOR 10kΩ 1/8WR592 D0GD222JA017 RESISTOR 2,20 kΩ 1/8WR593 D0GD103JA017 RESISTOR 10kΩ 1/8WR594 D0GD104JA017 RESISTOR 100kΩ 1/8WR596 ERJ6GEYJ333V RESISTOR 33kΩ 1/8WR601 D0GD153JA017 RESISTOR 15kΩ 1/8WR603 D0GD393JA017 RESISTOR 39kΩ 1/8WR604 ERJ6GEYJ821V RESISTOR 820Ω 1/8WR605 ERJ6GEYJ821V RESISTOR 820Ω 1/8WR606 ERJ6GEYJ821V RESISTOR 820Ω 1/8WR607 D0GD101JA017 RESISTOR 100Ω 1/8WR612 D0GD102JA017 RESISTOR 1kΩ 1/8WR617 D0GD391JA017 RESISTOR 390Ω 1/8WR619 D0GD121JA017 RESISTOR 120Ω 1/8WR620 D0GD121JA017 RESISTOR 120Ω 1/8WR623 D0GD331JA017 RESISTOR 330Ω 1/8WR633 D0GD470JA017 RESISTOR 47Ω 1/8WR640 D0GD822JA017 RESISTOR 8,20 kΩ 1/8W

Ref. No. Part No. Part Name & Description Ref. No. Part No. Part Name & Description

- 30 -

TC-20KL05P

Part No.

R672 D0GD181JA017 RESISTOR 180Ω 1/8WR685 D0GD750JA017 RESISTOR SMDR686 D0GD470JA017 RESISTOR SMDR687 D0GD472JA017 RESISTOR 4,70 kΩ 1/8WR688 D0GD103JA017 RESISTOR 10kΩ 1/8WR801 D0D72R2KA002 RESISTOR 2,20 Ω 7WR810 ERG2FJ470 RESISTOR 47Ω 2WR811 ERG2FJ104H RESISTOR 100kΩ 2WR817 AA2T0J39R004B RESISTOR 39Ω 1/2WR818 ERG2FJ473H RESISTOR 47kΩ 2WR820 ERX12SJR33E RESISTOR 0,33 Ω 1/2WR821 ERX12SJR27E RESISTOR 0,27 Ω 1/2WR824 D0AE152JA046 RESISTOR 1,50 kΩ 1/4WR825 D0AE102JA046 RESISTOR 1kΩ 1/4WR830 D0AE101JA046 RESISTOR 100Ω 1/4WR831 EROS2THF1102 RESISTOR 11kΩ 1/2WR832 D0AE473JA046 RESISTOR 47kΩ 0,25WR840 ERC12ZGM825V RESISTOR 8,20 MΩ 1/2 WR854 ERJ6GEYJ103V RESISTOR 10kΩ 1/8WR855 ERDS2TJ752T RESISTOR 7,50 kΩ 1/4WR857 ERDS2TJ683T RESISTOR 68kΩ 1/4WR858 ERDS2TJ153T RESISTOR 15kΩ 1/4WR861 ERDS1TJ221T RESISTOR 220Ω 1/2WR864 D0GD103JA017 RESISTOR 10kΩ 1/8WR866 D0GD472JA017 RESISTOR 4,70 kΩ 1/8WR867 D0AE272JA046 RESISTOR 2,70 kΩ 0,25WR868 ERDS1TJ471T RESISTOR 470Ω 1/2WR870 ERJ6GEYJ222V RESISTOR 2,20 kΩ 1/8WR871 ERDS1TJ103T RESISTOR 10kΩ 1/2WR872 D0GD272JA017 RESISTOR 2,70 kΩ 1/8WR873 D0GD472JA017 RESISTOR 4,70 kΩ 1/8WR875 D0GD103JA017 RESISTOR 10kΩ 1/8WR1016 ERJ6ENF1800V RESISTOR 180Ω 1/10WR1017 ERJ6ENF2400V RESISTOR 240Ω 1/10WR1018 ERJ6ENF3300V RESISTOR 330Ω 1/10WR1019 ERJ6ENF4700V RESISTOR 470Ω 1/10WR1020 ERJ6ENF8200V RESISTOR 820Ω 1/10WR1059 D0GD182JA017 RESISTOR 1,80 kΩ 1/8WR1060 D0GD683JA017 RESISTOR 68kΩ 1/8WR1103 D0GD680JA017 RESISTOR 68Ω 1/8WR1104 D0GD562JA017 RESISTOR 5,60 kΩ 1/8WR1105 D0GD562JA017 RESISTOR 5,60 kΩ 1/8WR1106 D0GD102JA017 RESISTOR 1kΩ 1/8WR1108 D0GD101JA017 RESISTOR 100Ω 1/8WR1109 D0GD101JA017 RESISTOR 100Ω 1/8WR1110 D0GD102JA017 RESISTOR 1kΩ 1/8WR1111 D0GD103JA017 RESISTOR 10kΩ 1/8WR1112 D0GD332JA017 RESISTOR 3,30 kΩ 1/8WR1115 D0GD103JA017 RESISTOR 10kΩ 1/8WR1116 D0GD332JA017 RESISTOR 3,30 kΩ 1/8WR1120 D0GD432JA017 RESISTOR 4,30 kΩ 1/8WR1122 D0GD332JA017 RESISTOR 3,30 kΩ 1/8WR1123 D0GD751JA017 RESISTOR 750Ω 1/8WR1125 D0GD103JA017 RESISTOR 10kΩ 1/8WR1130 D0GD101JA017 RESISTOR 100Ω 1/8WR1131 D0GD101JA017 RESISTOR 100Ω 1/8WR1132 D0GD101JA017 RESISTOR 100Ω 1/8WR1133 D0GD562JA017 RESISTOR 5,60 kΩ 1/8WR1134 D0GD103JA017 RESISTOR 10kΩ 1/8WR1135 D0GD333JA017 RESISTOR 33kΩ 1/8WR1136 D0GD332JA017 RESISTOR 3,30 kΩ 1/8WR1140 ERJ6ENF1201V RESISTOR 1,20 kΩ 1/10WR1141 D0GD562JA017 RESISTOR 5,60 kΩ 1/8WR1142 D0GD100JA017 RESISTOR 10Ω 1/8WR2101 D0GD101JA017 RESISTOR 100Ω 1/8WR2102 D0GD101JA017 RESISTOR 100Ω 1/8WR2106 D0GD101JA017 RESISTOR 100Ω 1/8WR2107 D0GD101JA017 RESISTOR 100Ω 1/8WR2109 D0GD101JA017 RESISTOR 100Ω 1/8WR2112 D0GD222JA017 RESISTOR 2,20 kΩ 1/8WR2113 D0GD222JA017 RESISTOR 2,20 kΩ 1/8WR2120 D0GD184JA017 RESISTOR 180kΩ 1/8WR2130 D0GD471JA017 RESISTOR 470Ω 1/8W

Ref. No. Part No. Part Name & Description

R2131 D0GD101JA017 RESISTOR 100Ω 1/8WR2151 D0GD563JA017 RESISTOR 56kΩ 1/8WR2152 D0GD273JA017 RESISTOR 27kΩ 1/8WR2153 D0GD221JA017 RESISTOR 220Ω 1/8WR2154 D0GD621JA017 RESISTOR 620Ω 1/8WR2155 D0GD471JA017 RESISTOR 470Ω 1/8WR2302 D0GD153JA017 RESISTOR 15kΩ 1/8WR2303 D0GD472JA017 RESISTOR 4,70 kΩ 1/8WR2380 D0GD151JA017 RESISTOR 150Ω 1/8WR2381 D0GD102JA017 RESISTOR 1kΩ 1/8WR2382 D0GD102JA017 RESISTOR 1kΩ 1/8WR2383 D0GD103JA017 RESISTOR 10kΩ 1/8WR2384 D0GD100JA017 RESISTOR 10Ω 1/8WR3010 D0GD184JA017 RESISTOR 180kΩ 1/8WR3012 D0GD184JA017 RESISTOR 180kΩ 1/8WR3015 D0GD101JA017 RESISTOR 100Ω 1/8WR3018 D0GD750JA017 RESISTOR 75Ω 1/8WR3022 D0GD101JA017 RESISTOR 100Ω 1/8WR3032 D0GD101JA017 RESISTOR 100Ω 1/8WR3033 D0GD101JA017 RESISTOR 100Ω 1/8WR3034 D0GD181JA017 RESISTOR 180Ω 1/8WR3035 D0GD560JA017 RESISTOR 56Ω 1/8WR3036 D0GD330JA017 RESISTOR 33Ω 1/8WR3048 D0GD184JA017 RESISTOR 180kΩ 1/8WR3132 D0GD331JA017 RESISTOR SMDR3133 D0GD331JA017 RESISTOR SMDR3141 D0GD184JA017 RESISTOR SMDR3142 D0GD184JA017 RESISTOR SMDR3144 D0GD101JA017 RESISTOR SMDR3145 D0GD101JA017 RESISTOR SMDSWITCHSW1001 EVQ11G05R SWITCHSW1002 EVQ11G05R SWITCHSW1003 EVQ11G05R SWITCHSW1004 EVQ11G05R SWITCHSW1005 EVQ11G05R SWITCHSW1006 EVQ11G05R SWITCHSW801 ESB92DA1B SWITCHOSCILATORSX181 EFCS4R5MW5 CERAMIC FILTER 4,5 MHZX184 EFCS4R5YS5W CRYSTAL 4,5 MHZX601 H0D120500020 CRYSTAL 12MHzX2130 H0D184500008 CRYSTAL 18,4 MHZXF101 M1971M SAW FILTER 45,75 MHZTRANSFORMEST501 ZTFP12504A TRAFO FLYBACK 15.750 Hz 0,040 kVAT553 ETH19Y210AZZ HORIZONTAL DRIVER 15.750 HzT801 ETS29AV136AD TRAFO 0,095 kVA (95VA) 107,21 KHZTUNERTU001 ENV56K10G3F TUNER

Ref. No. Part Name & Description

Panasonic da Amazônia S.A.

CS DIVISION - TECHNICAL SUPPORT

Rod. Presidente Dutra, Km 155

São José dos Campos - SP

BRAZIL