N-75N-75N-75N-75N-75N-75N-75N-75N-75 · K347-001-000 K347-002-000 CN3511X04-001-1/1...
Transcript of N-75N-75N-75N-75N-75N-75N-75N-75N-75 · K347-001-000 K347-002-000 CN3511X04-001-1/1...
N-7
5Ω
(25)
KJ COMTECH Co., Ltd 136-1, Sosabon-3dong, Sosa-gu, Bucheon-si, Gyunggi-do, KoreaTel. 82-32-347-8015,6,8(Ext.223), Fax. 82-32-347-8017, www.kjct.co.kr 10.2006324·Connector
N-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75Ω
Connector·325KJ COMTECH Co., Ltd 136-1, Sosabon-3dong, Sosa-gu, Bucheon-si, Gyunggi-do, KoreaTel. 82-32-347-8015,6,8(Ext.223), Fax. 82-32-347-8017, www.kjct.co.kr 10.2006
N-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75Ω
Microminiature Coaxial Connector
Plug (Male) Jack (Female)
KJ-COMTECH N connectors are available with 50Ωand 75Ω impedance.The N 75Ω connectors are suitable for applicationsup to 1.5 GHz. The screw-type coupling mechanismprovides a sturdy and reliable connection. N 75Ωconnectors are available in many different patterns.
Compatibility:Centre conductors of N 75Ω connectors have asmaller diameter than those of the 50Ω and N 75Ωconnectors are not intermateable.
Microminiature Coaxial ConnectorTechnical DataMaterial DataCable ConnectorsReceptacles with Solder EndAdaptor within-SeriesTermination
324325325326328329329
Technical Data
Material Data
PININSULATOR
BODIESSPRING RING
GASKETINSERT
BACK NUTCRIMP FEMALE
Connector PartMaterial
Male FemalePlating
BrassPTFEBrass
Stainless-SteelSilcone-Rubber
BrassBrassBrass
Beryllium-CopperPTFEBrass
--
BrassBrassBrass
Gold-
Nickel or Silver--
Nickel or SilverNickelNickel
Pulg (male)
Min. Max. Min. Max.
Jack (Female)
ABCDEFG
- 8.68 / 0.342 8.03 / 0.316 8.13 / 0.320
5.33 / 0.210 5.84 / 0.230 4.75 / 0.187 5.26 / 0.207
- 2.00 / 0.079 - 2.00 / 0.079
16.00 / 0.630 - - 15.93 / 0.627
1.00 / 0.039 1.05 / 0.041 5.33 / 0.210 -
- - 9.04 / 0.356 9.19 / 0.362
- - 6.76 / 0.266 -
Description
Interface Dimensions
Interface Dimensions in mm/inch
Contents Requirement Specification
Impedance Frequency range Dielectric withstanding voltage (at sea level)Working voltage (at sea level)Insulation resistanceContact resistance- Center contacts- Outer contacts
75ΩDC .......... 1.5GHz2.5 kV rms, 50 Hz ≤ 1.0 kV rms, 50 Hz≥ 5·103 MΩ
≤ 1.0mΩ≤ 1.0mΩ
Coupling nut torque- recommended- proof torqueCoupling nut retention forceContact captivationDurability (matings)
0.68Ncm ~ 1.13Ncm / 6.0 in. lbs ~ 0.0 in. lbs1.70 Ncm / 15.0 in. lbs≥ 450 N / 101.2 lbs≥ 28 N / 6.3 lbs≥ 500
ELECTRICAL DATA TEST REQUIREMENTS
MECHANICAL DATA TEST REQUIREMENTS
N-7
5Ω
(25)
KJ COMTECH Co., Ltd 136-1, Sosabon-3dong, Sosa-gu, Bucheon-si, Gyunggi-do, KoreaTel. 82-32-347-8015,6,8(Ext.223), Fax. 82-32-347-8017, www.kjct.co.kr 10.2006326·Connector
N-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75Ω
Connector·327KJ COMTECH Co., Ltd 136-1, Sosabon-3dong, Sosa-gu, Bucheon-si, Gyunggi-do, KoreaTel. 82-32-347-8015,6,8(Ext.223), Fax. 82-32-347-8017, www.kjct.co.kr 10.2006
N-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75Ω
RG179
fig.1
5C-2V
fig.2
Cable Connectors
Fig
1
2
TypeCode Cable Goup
(example)Old Code New CodeNote
Nickel
Nickel
Gold
Gold
Nickel
Nickel
N75-PC-179
N75-PC-5C-HFB
K347-001-000
K347-002-000
CN3511X04-001-1/1
CN3511X34-001-1/1
RG179
5C-2V
X04
X10
Pin Body Crimp
PlatingAS-In
RG6A/U
fig.1
Fig
1
TypeCode Cable Goup
(example)Old Code New CodeNote
NickelGold NickelN75-P3-RG6/U K347-006-000 CN3511X11-001-1/1 X11 RG6A/U
Pin Body Back Nut
PlatingAS-In
For flexible cablesCable entry clamp RG59 B/U
fig.1
RG11A/U
fig.2
Fig
1
2
TypeCode Cable Goup
(example)Old Code New CodeNote
Nickel
Nickel
Gold
Gold
Nickel
Nickel
N75-J3-59
N75-J3-RG11
K347-220-000
K347-221-000
CN3512X09-001-1/1
CN3512X18-001-1/1
X09 RG59 B/U
X18 RG11A/U
Pin Body Back Nut
PlatingAS-In
For flexible cablesCable entry clamp
For flexible cablesCable entry clampCentre contact solderedWith panel seal
For flexible cablesCable entry crimpCable contact soldered
RG59
fig.1
RG11A/U
fig.2
Fig
1
2
TypeCode Cable Goup
(example)Old Code New CodeNote
Nickel
Nickel
Gold
Gold
Nickel
Nickel
N75-LP3-59
N75-LP3-RG11
K347-115-000
K347-116-000
CN3531X09-001-1/1
CN3531X18-001-1/1
X09 RG59
X18 RG11A/U
Pin Body Coupling
PlatingAS-In
For flexible cablesCable entry clampCentre contact soldered
RG179
fig.1
RG59 B/U
fig.2
RG11 A/U
fig.3
Fig
1
2
3
TypeCode Cable Goup
(example)Old Code New CodeNote
Nickel
Nickel
Nickel
Gold
Gold
Gold
Nickel
Nickel
Nickel
N75-BJ-3-179
N75-BJ-3-59
N75-BJ-3-RG11
K347-331-000
K347-333-000
K347-332-000
CN3522X04-001-1/1
CN3522X09-001-1/1
CN3522X18-001-1/1
RG179
RG59 B/U
RG11 A/U
X04
X09
X08
Pin Body Back Nut
PlatingAS-In
Straight Cable Plugs(male)
Right Angle Cable Plugs(male)
Straight Cable Jacks(female)
Straight Bulkhead Cable Jacks(female)
N-7
5Ω
(25)
KJ COMTECH Co., Ltd 136-1, Sosabon-3dong, Sosa-gu, Bucheon-si, Gyunggi-do, KoreaTel. 82-32-347-8015,6,8(Ext.223), Fax. 82-32-347-8017, www.kjct.co.kr 10.2006328·Connector
N-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75Ω
Connector·329KJ COMTECH Co., Ltd 136-1, Sosabon-3dong, Sosa-gu, Bucheon-si, Gyunggi-do, KoreaTel. 82-32-347-8015,6,8(Ext.223), Fax. 82-32-347-8017, www.kjct.co.kr 10.2006
N-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75ΩN-75Ω
For flexible cablesCable entry clampCentre contact soldered
RG179
fig.1
RG59 B/U
fig.2
RG11 A/U
fig.3
Fig
1
2
3
TypeCode Cable Goup
(example)Old Code New CodeNote
Nickel
Nickel
Nickel
Gold
Gold
Gold
Nickel
Nickel
Nickel
N75-J-H4-3-179
N75-J-H4-3-59
N75-J-H4-3-RG11
K347-225-000
K347-222-000
K347-223-000
CN3544X04-001-1/1
CN3544X09-001-1/1
CN3544X18-001-1/1
X04 RG179
X09 RG59 B/U
X18 RG11 A/U
Pin Body Back Nut
PlatingAS-In
Receptacle with Solder End
fig.1
Fig
1
TypeCode
Old Code New CodeNote
NickelGoldN75-J-H4-R K347-410-000 CN3544000-001-1/1 ML87
Pin Body
PlatingAS-InMounting Hole
Fig
1
2
TypeCode
Old Code New CodeNote
Nickel
Nickel
Gold
Gold
N75-A-JJ
N75-A-PP
K347-702-000
K347-701-000
AD3512-001-1/1
AD3511-001-1/1
Pin Body Coupling
-
Nickel
PlatingAS-In
Panel mounted
Adaptors within Series
Jack to Jack (female)
fig.1
Plug to Plug (male)
fig.2
Flange Mount Jack (female)
Straight Panel Cable Jacks (female)
Straight Adaptors
fig.1 fig.2
Fig
1
2
TypeCode
Old Code New CodeNote
Nickel
Nickel
Gold
Gold
≤1.2
≤1.2
N75-P-TERM
N75-J-TERM
K347-911-000
K347-912-000
CN3591-001-1/1
CN3594-001-1/1
PinDC~1.5GHz Body
Nickel
Nickel
No Chain
No Chain
Back Nut
PlatingV.S.W.R
Terminations
N-7
5Ω
(25)
KJ COMTECH Co., Ltd 136-1, Sosabon-3dong, Sosa-gu, Bucheon-si, Gyunggi-do, KoreaTel. 82-32-347-8015,6,8(Ext.223), Fax. 82-32-347-8017, www.kjct.co.kr 10.2006330·Connector Connector·331KJ COMTECH Co., Ltd 136-1, Sosabon-3dong, Sosa-gu, Bucheon-si, Gyunggi-do, Korea
Tel. 82-32-347-8015,6,8(Ext.223), Fax. 82-32-347-8017, www.kjct.co.kr 10.2006
NNNNNNNNNNNNNNNNNNNNNN
Shink Sleeve Ferrule Contact Body
Solder Point
MOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTION
·K345-001·K345-002
1. Insert the ferrule and the heat shrink sleeve intothe cable and strip off the outer seath.
Step 1.
Step 2.
Step 3.
Step 4.
Step 5.
2. After striping off the out conductor and the innerconductor as shown in the diagram.
3. Insert the center contact into the cable andsolder the solder point.
4. Insert the center contact and the dielectric coreof the cable into the body the be weapped withthe above section of the body as shown in thediagram. After done, push the ferrule into it andcrimp with the crimp tool.
5. Push the heat shrimk sleeve to the ferrule fin-ished crimping and contract by heating.
STANDARD CRIMP
CONNECTORS·K345-003 ·K345-007·K345-004 ·K345-008·K345-005 ·K347-009·K345-006 ·K347-010
1. Cut the cable as much as requied. Step 1.
Step 2.
Step 3.
Step 4.
Step 5.
2. Insert the back nut, the washer, the gasket, theclamp into the cable in the order named andstrip off the out seath.
3. After stripping off the lnner conductor and theouter conductor as shown in the diagram.
4. Attach the outer conductor to the above of theclamp putting it to the solder point of the lnnercontact and solder it.
5. Insert the cable, the washer, he gasket backnut into the body and screw it.
Back Nut Washer Gasket Insert Contact Body
Solder Point
STANDARD CLAMP
CONNECTORS
N-7
5Ω
(25)
KJ COMTECH Co., Ltd 136-1, Sosabon-3dong, Sosa-gu, Bucheon-si, Gyunggi-do, KoreaTel. 82-32-347-8015,6,8(Ext.223), Fax. 82-32-347-8017, www.kjct.co.kr 10.2006332·Connector Connector·333KJ COMTECH Co., Ltd 136-1, Sosabon-3dong, Sosa-gu, Bucheon-si, Gyunggi-do, Korea
Tel. 82-32-347-8015,6,8(Ext.223), Fax. 82-32-347-8017, www.kjct.co.kr 10.2006
NNNNNNNNNNNNNNNNNNNNNNMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTIONMOUNTING INSTRUCTION
Shink Seelve Ferrule Body
Solder Point
Cap
Insulator
·K345-113·K345-114
1. After inserting the ferrule and the heat shrinksleeve into the cable, strip off the outer seath.
Step 1.
Step 2.
Step 3.
Step 4.
2. After stripping off the out conductor and the in-ner conductor as shown in the diagram, pre-pare the lnner conductor to solder.
3. Insert the cable and the ferrule into the body.
4. After crimping in the crimp zone and contractingthe shrink sleeve, seal up the insulator, the capin the order named.
RIGHT ANGLE CRIMP
CONNECTORS
·K345-111·K345-112
1. Cut the cable as much as required. Step 1.
Step 2.
Step 3.
Step 4.
2. Insert the back nut, the washer, the gasket,the clamp in the order named and strip off theout seath.
3. Attach the outer conductor to the above of theclamp equally putting it to the solder point ofthe inner contact and then solder it.
4. Insert the cable, the washer, the gasket backunt into the body and screw the back nut.
Back Nut Washer Insulator Clamp Body
Cap
Solder Point
Insulator
RIGHT ANGLE CLAMP
CONNECTORS