Installation Guide Wireless ADSL2+ Router

ZTE ZXV10 W300 v5.2 / ZXV10 W300B v5.2

www.otebusiness.gr

Περιετόμενα Contents

Minimum System Requirements................................................................................................................................. . .3

Package Contents............................................................................................................................................................ . 4

LED Indications............................................................................................................................................................... ..5

Ports ..................................................................................................................................................... ............................ . 6

Connection ADSL2+ Router .......................................................................................................................................... . 7

PSTN Line.................................................................................................................................................................... .8

ISDN Line.....................................................................................................................................................................11

Internet Settings......................................................................................................................................................... 14

Wireless Connection.........................................................................................................................................................19

Activation/Deactivation of Wireless Network & Reset of ADSL2+ Router.............................................................25

Change Internet access Username & Password.................................................................................. ...... ...... ............26

Hardware Warranty...........................................................................................................................................................26

Connection Data................................................................................................................................................................27

Eλάτιζηες Απαιηήζεις Σσζηήμαηος Minimum System Requirements

1. Processor Pentium 4

2. Windows XP/Vista/7 or Mac OS 9.x

3. 1 GB RAM

4. 25 MB free space on the hard disc

5. Ethernet Network Card 10/100 Mbps

3

Περιετόμενα Σσζκεσαζίας

Package Contents

1 ADSL2+ Wireless Router

2 Phone Cables (RJ-11)

1 Ethernet Cable (RJ-45)

1 Installation CD

Installation Guide

1 Power adapter

1 Splitter

1 Filter (for PSTN)

www.otebusiness.gr

4

Status

LED

Color Status Description

POWER

Off Power off

(Red) Blinking Software upgrade in progress

(Green) On solid Power is on

DSL

Off Non detectable signal

(Green) Blinking Router attempting to connect

(Green) On solid Router is on

INTERNET

Off System in bridge connection status or ADSL is not connected

(Green) Blinking Partial data transmission through the Router

(Green) On solid The system has an internet address and ADSL is connected. IP data packets are transmitted normally.

(Red) On solid The device attempted an IP connection and failed (no DHCP response, no PPPoE response, PPPoE quality

check failed, no IP address from, IPCP etc.)

LAN1~LAN3

& STB

&

STB

Off Ethernet interface is in non communication status

(Green) Blinking Data received and transmitted through Ethernet

interface.

(Green) On solid Ethernet is in communication status

WLAN Off Wi-Fi interface is off

(Green) Blinking Data received and transmitted through Wi-Fi

interface

(Green) On solid Wi-Fi interface On

LED Indications

There are the following LEDs in the front panel of the ADSL2+ Router. Check the meaning of each LED below (Image 1).

Image No 1

5

Port connections

The ADSL2+ Router has the following switches and port connections (Image 2):

LED Status DESCRIPTION ACTIVITY

POWER Power Inlet Connection with 220V power adapter

SWITCH Power switch Turns router ON / OFF

Wi-Fi Wireless network

button Turns wireless network ON / OFF.

LAN4 (STB)

Ethernet port

for connection of

decoder Connection with OTE subscription TV

over the Internet

LAN1~LAN3 Ethernet port for

connection of PC

Connection of up to three PCs for internet access

and creation of a local network

LINE Port for telephone cable

connection (RJ-11) Connection with phone jack or splitter.

RESET Factory default reset

button Resets default settings.

6

Connection of ADSL2+ Router

Connection of ADSL2+ Router

Follow the instructions below to connect the ADSL2+ Router over a PSTN

or ISDN phone line.

7

PSTN Line

If you have a PSTN phone line(simple analog line), connect the ADSL2+ Router as shown below.

8

1 2 3

PSTN Line

You must unplug any other telephone devices connected to the phone jack.

Use the blue cable to connect the blue port of the splitter to the phone jack.

A. Use the grey cable to connect the grey port of the splitter to the grey port on the Conn-x@work router.

B. Then connect the cable of your phone to the black port of the splitter.

Use the yellow cable to connect the ETHERNET port on your computer to one of the first three ports on the Conn-x@Work router.

ATTENTION: The purple port (STB) is used only for connection of a decoder required for the OTE subscription TV over the Internet.

9

PSTN Line

4 Connect the power adaptor to the Conn-x@Work power inlet and plug it in.

Press the power button SWITCH in the back panel of the router to turn your router on.

The Power, DSL, Internet, LAN and WLAN LEDs will light up.

If you wish to connect additional phones to other plugs, you must use a filter for each phone device. Connect your phone to the filter and the filter to the phone jack.

Note: If your phone network is connected to any other device (alarm, switchboard, etc.), you must use additional ADSL filter or splitter. Please address a specialized crew.

10

ISDN Line

If you have an ISDN phone line, connect the ADSL2+ Router as shown below.

11

ISDN Line

1

2

Disconnect the phone cable from the ISDN (N.T. 1) device and connect it to the black port of the splitter.

A. Use the blue cable to connect the blue port of the splitter to

the phone jack.

B. Use the grey cable to connect the grey splitter port to the grey port on the Conn-x@Work router.

Note: If your phone network is connected to any other device (alarm, switchboard, etc.), you must use additional ADSL filter or splitter. Please address a specialized crew.

12

3

4

ISDN Line

Use the yellow cable to connect the ETHERNET port on your computer to one of the first three yellow ports of the Conn-x@Work.

ATTENTION: The purple port (STB) is used only for connection of a decoder required for the OTE subscription TV over the Internet.

Connect the power adaptor to the Conn-x@Work power inlet and plug it in.

Press the power button SWITCH in the pack panel of the router to turn your router on.

The Power, DSL, Internet, LAN and WLAN LEDs will light up.

13

Internet Settings

Internet Settings

To install the ADSL2+ Router, insert the CD in your CD-ROM drive. The CD should run automatically. If the CD does not run automatically, go to

Windows Explorer, select the CD-ROM drive where your CD is located, double click on setup.exe and follow the instructions.

If you are not able to install the ADSL2+ Router through the CD, follow the following instructions:

14

Internet Settings

Go to your Browser. In the field “Address” (Image 1) type http://192.168.1.1 and Press «Enter».

The next screen will appear (Image 2):

The indications for ADSL, ATM and Internet Status must be green. If one of them is red, check your cable connections and try again.

Image 1

Image 2

15

1

2

Internet Settings

Click on “Administration”. The next screen will appear (Image 3):

Image 3

16

Internet Settings

In the field «Username» type «admin».

In the field «Password» type the password that is written on the label on the underside of your ADSL2+ Router and click ΟΚ. Make a note of the Username and Password on the last page of this manual.

17

3

Internet Settings

The next screen will appear (Image 4):

In the field «Username» fill in the username provided to you when you purchased Conn-x@Work package followed by @otenet.gr

In the field «Password» fill in the password provided to you when you purchased Conn-x@Work package. Click «Apply» to store the settings. You are now connected to the Internet!

Close your Browser.

Image 4

18

Wireless Connection

Wireless Connection

Follow the following instructions for a wireless connection to the internet.

19

Wireless Connection

To make a wireless internet connection you must have completed the Internet Settings.

If you wish to make a wireless connection with a desktop computer, you must have a wireless USB stick or

wireless network card installed and activated on your computer.

If you wish to make a wireless connection with a laptop, you must first activate the wireless function (check your laptop’s manual).

We suggest keeping the default settings to facilitate installation. You can change the settings afterwards through the wireless network settings menu (check the user manual in the CD).

20

wireless Connection

Double-click on the wireless network icon on your computer screen to see the available wireless networks.

21

1

2

Wireless Connection

The name of your wireless network to look for is the same as the SSID name that is written on the label on the underside of your router or on the CD cover. Make a note of the SSID name on the last page of the manual.

Click on the wireless network that corresponds to your SSID name and click Connect.

22

Wireless Connection

In the screen that appears, enter the network security key (WPA) which you can find on the label on the underside of your router or on the CD cover with the WPA name and click ΟΚ. Make a note of the network security key (WPA) on the last page of the manual.

23

3

Wireless Connection

Connecting to the network.Please wait...

You are now connected to the Internet! Attention! You must repeat the section Wireless Connection

or Connect Wirelessly from the installation CD for any additional device you wish to connect

wirelessly.

24

Activation/Deactivation of Wireless Network & Reset of ADSL2+ Router

Wireless operation is activated. To deactivate it, press and hold pressed the Wi-Fi button on the back of the ADSL2+ Router until

the WLAN LED on the front side of the ADSL2+ Router is off.

To activate wireless operation, press and hold pressed the same button for more than 1 second. The WLAN LED will turn on.

If you wish to return your ADSL2+ Router to the default settings, first make sure that the ADSL2+ Router is on. Press and hold

pressed the RESET switch on the underside of your ADSL2+

Router, until all LEDs are off.

Wait until the LEDs of the ADSL2+ Router turn back ON. Resetting to default settings will delete any information you have

entered and stored in the ADSL2+ Router.

25

2

1

3

Change Internet access Username & Password

If you want to change the Username and Password (you can only change the Username once

but you can change the password as many times as you wish), open your web browser and on

the address line type http://my.otenet.gr

In the webpage that appears, click on the Change of Conn-x name and

password and follow the instructions.

If you change the Username or Password, you must repeat the Internet Settings.

Equipment Warranty

Your equipment comes with a one (1) year warranty from the date of purchase.

26

You can fill in here your connection information:

ρείηε να ζσμπληρώζεηε εδώ ηα ζηοιτεία ηης ζύνδεζής ζας:

Username for Internet access

Password for Internet access

Username Equipment

Password Equipment

Κωδικός SSID

Network Security Key (WPA)

27

Ple

ase

recycle

A

PR

IL 2

011

24-hours Technical Support For questions and assistance Before and during ADSL installation call, call

(local rate for all Greece)