Hilti MI industrial pipe support system Technical ... · Hilti MI industrial pipe support system...

page 1

Hilti MI industrial pipe support systemTechnical documentation

Hilti MI industrial pipe support system

page 2


page 3

Technical data

MI-90 MI-120Material thickness s [mm] 3.5 4.0Cross-sectional area A [mm2] 1002.6 1375.7Weight of girder [kg /m] 9.43 12.60

MaterialElastic limit (yield strength) fy,k [N/mm2] 235.0 235.0Permissible tensile stress* σZul [N/mm2] 152.6 152.6Modulus of elasticity [N/mm2] 210000 210000Shear modulus [N/mm2] 81000 81000

SurfaceHot-dip galvanized 70 µm ● ●

Cross-section values y-axisAxis of gravity ey [mm] 45.0 60.0Moment of inertia ly [cm4] 115.34 265.78Section modulus Wy [cm3] 25.63 44.30Radius of gyration iy [cm] 3.39 4.40

Cross-section values x-axisAxis of gravity ez [mm] 45.00 45.00Moment of inertia lz [cm4] 115.34 173.58Section modulus Wz [cm3] 25.63 38.57Radius of gyration iz [cm] 3.39 3.55

Torsion dataTorsional moment of inertia Σ lt [cm4] 155.56 297.02Torsional section modulus Wt = 2* ABredt * [cm3] 45.25 71.63

Technical data /mean valuesincluding torsion

90

50

2590 s = 3.5

120

90 s = 4

50

25

* The permissible stress is calculated from σD / γG/Q with γ = 1,4. σD results from higher yield strength due to cold forming in accordance with DAST-RILI016, issued 1992:σD = fyk / γM mit γM = 1,1


page 4

Single-span subject to bending in one axisF1 when f=L/200, F2 when f=L/300, F when σzul including the framing section’s own weight

MI-90, one single load

Length of F [kN] f [mm] F1 [kN] f [mm] F2 [kN] f [mm]span [mm] ≤ σzul ≤ L/200 ≤ L/300

250 58.75 < 0.1 – – – –500 30.75 0.3 – – – –750 20.67 0.8 – – – –

1000 15.54 1.3 – – – –1250 12.43 2.1 – – – –1500 10.34 3.0 – – – –1750 8.85 4.1 – – – –2000 7.72 5.4 – – – –2250 6.85 6.8 – – – –2500 6.14 8.4 – – 6.06 8.32750 5.56 10.2 – – 4.97 9.23000 5.08 12.2 – – 4.14 10.03250 4.67 14.3 – – 3.49 10.83500 4.31 16.6 – – 2.97 11.73750 4.00 19.1 3.92 18.8 2.55 12.54000 3.73 21.8 3.41 20.0 2.20 13.34250 3.50 24.6 2.98 21.3 1.91 14.24500 3.30 27.6 2.62 22.5 1.66 15.04750 3.10 30.8 2.31 23.8 1.45 15.85000 2.90 34.2 2.05 25.0 1.27 16.75250 2.70 37.8 1.82 26.3 1.11 17.55500 2.60 41.6 1.61 27.5 0.97 18.35750 2.50 45.5 1.44 28.8 0.85 19.26000 2.30 49.7 1.28 30.0 0.74 20.0

MI-120, one single load

Length of F [kN] f [mm] F1 [kN] f [mm] F2 [kN] f [mm]span [mm] ≤ σzul ≤ L/200 ≤ L/300

250 101.32 < 0.1 – – – –500 53.13 0.2 – – – –750 35.73 0.6 – – – –

1000 26.86 1.0 – – – –1250 21.50 1.6 – – – –1500 17.90 2.3 – – – –1750 15.32 3.1 – – – –2000 13.38 4.0 – – – –2250 11.87 5.1 – – – –2500 10.66 6.3 – – – –2750 9.66 7.7 – – – –3000 8.83 9.1 – – – –3250 8.12 10.7 – – – –3500 7.51 12.4 – – 7.03 11.73750 6.98 14.3 – – 6.07 12.54000 6.52 16.3 – – 5.28 13.34250 6.10 18.4 – – 4.62 14.24500 5.74 20.7 – – 4.07 15.04750 5.41 23.1 – – 3.60 15.85000 5.11 25.6 4.98 25.0 3.20 16.75250 4.80 28.2 4.47 26.3 2.85 17.55500 4.60 31.0 4.01 27.5 2.54 18.35750 4.50 34.0 3.62 28.8 2.27 19.26000 4.10 37.1 3.27 30.0 2.03 20.0

90

50

2590 s = 3.5

120

90 s = 4

50

25

L/2 L/2

L

F

L/2 L/2

L

F

-5.00

0.00

5.00

10.00

15.00

20.00

25.00

30.00

35.00

40.00

45.00

50.00

0 500 1000 1500 2000 2500 3000

MI-90MI-120

MQ-41 D/F*MQ-21 D/F*

MQ-41/F*MQ-52-72 D/F*

L

F[kN]Selection of framing section for single span with max. load when f < L/200Single central load incl. framing section’s own weight

Load

F (k

N)

*Technical data for the MQ System can be found in the Installations Systems main catalogue.

Length of span (mm)


page 5

± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fx // Fz* 9.70 1.70 12.00Fy + Fx + Fz 9.70 1.70 12.00* Force permissible in only one direction ( // = or )Note: Not to be used for cantilevers. Section always requires support at both ends.

MI connector on MI girder (recommended loads1))

MIC-90-U or MIC-120-U on MI-90

± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fx // Fz* 10.30 1.70 13.70Fy + Fx + Fz 10.30 1.70 13.70* Force permissible in only one direction ( // = or)Note: Not to be used for cantilevers. Section always requires support at both ends.

MIC-90-U or MIC-120-U on MI-120MI-90

Fy

Fz

Fx

Fy

Fz

Fx

MI-90 or MI-120

Each with single screw (84 Nm)

± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fx // Fz* 13,20 8,26 18,60Fy + Fx + Fz 13,20 3,10 18,60* Force permissible in only one direction ( // = or)Note: Designed for use with cantilevers. May be supported at only one end.2)

MIC-90-L auf MI-90 oder MI-120

1) Calculation of rated values: Fd = Frec.�1,52) Our technical advisory service would be pleased to assist with design and calculation.

2 screws crosswise(84 Nm)

Single screw (84 Nm)


M12

M12 x 85

30Fy

Fx

Fz

± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fz 1.50 - 1.50Fy + Fx + Fz 0.78 5.80 0.78All loads apply to 1 beam clamp. Recommended shear loads apply to galvanized steel on galvanized steel.Clamps must always be used in pairs.Tightening torque MD: 69 Nm

MI beam clamps (recommended loads1))

MI-GC-M12


page 6

155150

60 x 13

12

220

140

14

MI-120

Fy

Fz

Fx

2 x screws crosswise(84 Nm)

4 x beam clamps (69 Nm)

300B

100

12140

MI-90

60 x 13

Fy

Fz

Fx

± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fx // Fz* 3.00 9.00 3.00Fy + Fx + Fz 1.56 5.00 1.56* Force permissible in only one direction ( // = or)Note: Not to be used for cantilevers. Always requires support at both ends.

MI connector on steel beams (recommended loads1))

MIC-S-90-AA

± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fx // Fz* 6.00 14.70 6,00Fy + Fx + Fz 3.11 14.70 3,11* Force permissible in only one direction (// = or)Note: Designed for use with cantilevers. May be supported at only one end.2)

MIC-S-90-A

155150

60 x 13

MI-90

12

220

140

14

Fy

Fz

Fx

± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fx // Fz* 6.00 10.20 6.00Fy + Fx + Fz 3.11 10.20 3.11* Force permissible in only one direction (// = or)Note: Designed for use with cantilevers. May be supported at only one end.2)

MIC-S-90-B


MIC-S-90-C2 x screws crosswise (84 Nm)

4 x beam clamps (69 Nm)

2 x screws crosswise (84 Nm)

2x beam clamps (69 Nm)


MIC-S-120-A


MIC-S-120-B


MIC-S-120-C

1) Calculation of rated values: Fd = Frec.�1,52) Our technical advisory service would be pleased to assist with design and calculation.


page 7

± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fx // Fz* 8.73 8.80 13.20Fy + Fx + Fz 1.60 3.60 1.60*Force permissible in only one direction ( // = or)Note: Designed for use with cantilevers. May be supported at only one end.2)

100

MI-90140

200

12

Fy

Fz

Fx

MI connector on concrete (recommended loads1))

MIC-C90-AA3)

156

47 x 17

15

156

230

MI-90

230

140Fy

Fz

Fx


MIC-C90-D4)

156

47 x 17

15

156

230

230

140Fy

Fz

Fx


MIC-C120-D4)

MI-90

100

200

8Fy

Fz

Fx

± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fy // Fz* 5.82 - 13.20Fy + Fz 5.82 - 11.67*Force permissible in only one direction ( // = or)Note: Not to be used for cantilevers. Always requires support at both ends.

MIC-C90-U3)

1) Calculation of rated values: Fd = Frec. x 1,52) Our technical advisory service would be pleased to assist with design and calculation.3) Fxrec.: Given values apply only to use of HST/HST-R M12 anchors; higher values possible when other

anchors are selected.Fyrec.: Given values apply to all M12 anchorsNote: When loading with Fy, the elongated hole in the base plate in line with the direction of force must be filled with high-strength mortar (e.g. HIT-HY 150).

4) Fxrec., Fyrec., Fzrec.: Given values apply only to use of HST/HST-R M16 anchors; higher values possiblewhen other anchors are selected.

screws crosswise (84 Nm)





page 8

250

MI-90

Fy

Fz

Fx

250

MI-120

Fy

Fz

Fx

Fy

Fz

Fx

1) Calculation of rated values: Fd = Frec. x 1,5

MI girder extension (recommended loads1))

MIC-90-E

The loading capacity of the extension depends on the moments acting in the Y- and Z-axes.Please consult our technical advisory service.

The loading capacity of the extension depends on the moments acting in the Y- and Z-axes.Please consult our technical advisory service.

MI connector / pedestal connector (recommended loads1))

MIC-T

MIC-120-E

± Fyrec. [kN] ± Fxrec. [kN] ± Fzrec. [kN]Fz* - - 20.00Fy + Fx + Fz 3.50 1.00 10.00* Force permissible in only one direction ( // = or )Note: Always to be fitted on both sides.

4 screws crosswise in end ofeach girder (84 Nm)

4 screws crosswise in end ofeach girder (84 Nm)

2 screws (84 Nm)


page 9

197,5

130

80

8120

12.5

100

1552

B

C

D

80

12

12.5

1460 x 13

6

90°

0°

100

100

6

80

8 200

12.5

25 x 14

150

90°

0°

Tension or compression Frec. [kN]2)

Angle 0° 30° 45° 60° 90°24.00 11.80 10.00 9.20 9.70

Note: Always to be fitted in pairs.

MI Multi-angle connectors ( recommended loads 1))

MIC-U-MA (connection to MI girder )


Angle 0° 30° 45° 60° 90°16.00 10.00 7.00 6.00 5.00

MIC-SA-MA (connection to steel beam)


Angle 0° 30° 45° 60° 90°12.00 10.00 7.00 6.00 5.00

MIC-SB-MA (connection to steel beam)


Winkel 0° 30° 45° 60° 90°8.00 8.00 7.00 6.00 5.00

MIC-SC-MA (connection to steel beam)

Tension or compression Frec. [kN]2)3)

Angle 0° 30° 45° 60° 90°7.10 5.00 4.00 4.00 5.30

MIC-CU-MA (connection to concrete)

1) Calculation of rated values: Fd = Frec. � 1,52) Frec. always acts in the longitudinal axis of the girder, irrespective of angle.3) Frec. : Given values apply only to use of HST/HST-R M12 anchors; higher values possible

when other anchors are selected.

2 screws (84 Nm)

4 beam clamps (69 Nm)


page 10


page 11

MI girder

Advantages■ Torsionally rigid girder.■ Pipes may be mounted on all four sides simultaneously.■ Scale marks facilitate installation /cutting to length.■ Crimped-in depression for 100% compatibility with MQ channel

system.

Section height Length Material thickness Weight Ordering designation Item no. Packaged[mm] (m) [mm] (kg/m) in lengths of

90 3 3.5 9.43 �➀MI-90 3m 304798 3m90 6 3.5 9.43 �➀MI-90 6m 304799 6m

120 3 4 12.60 �➁MI-120 3m 304800 3m120 6 4 12.60 �➁MI-120 6m 304801 6m

Technical dataMaterial: S235JRG2 as per DIN 10025 Galvanizing: Hot-dip galvanized 75 µm

90

50

2590 s = 3.5

�

120

90 s = 4

50

25

�


page 12

MI connectors: Crossbeam connectors

Advantages■ Fine adjustment in 5 mm increments for maximum flexibility.■ Only two connecting screws required.■ Keyed hold for optimum transmission of forces and moments.■ Self-locking nuts for vibration-resistant screw connections.

Technical dataMaterial: S235 JRG2 as per DIN EN 10 025 Galvanizing: Hot-dip galvanized 55µm

Crossbeam connectors with connecting partsFor girder type Weight per Ordering designation Item no. Package

set [kg] contents

MI- 90 2.36 � MIC-90-U 304803 4MI-120 2.79 � MIC-120-U 304804 4

Set besteht aus:2x

Crossbeam connectors without connecting partsFor girder type Weight per Ordering designation Item no. Package

set [kg] contents

MI- 90 1.78 � MIC- 90-U-AP 305708 4MI-120 2.18 � MIC-120-U-AP 305709 4

NoteAlways to be supported at opposite end.

192

758100

MI-90

220

758100

MI-120

�

�

Items in set


page 13

MI connectors: Cantilever connectors

Advantages■ Fine adjustment in 5 mm increments for maximum flexibility.■ Only four connecting screws required.■ Keyed hold for optimum transmission of forces and moments.■ Self-locking nuts for vibration-resistant screw connections

Technical dataMaterial: S235 JRG2 as per DIN EN 10 025 Galvanizing: Hot-dip galvanized 55 µm

Set besteht aus:4x

2x 2x

2x315

75

8140

Cantilever connector with connecting partsFor girder type Weight per Ordering designation Item no. Package

set [kg] contents

MI-90 3.95 MIC-90-L 304805 2➀

Cantilever connector without connecting parts

For girder type Weight per Ordering designation Item no. Packageset [kg] contents

MI-90 2.80 MIC-90-L-AP 305710 2

NoteDesigned for cantilever applications.May be supported at only one end.

Items in set


page 14

MI connectors: Pedestal connector

Technical dataMaterial: S235 JRG2 as per DIN EN 10 025Galvanizing: Hot-dip galvanized 55 µm

220

75

8120Pedestal connector with connecting parts


MI-90/MI-120 2.04 � MIC-T 304807 2

Advantages■ Fine adjustment in 5 mm increments for maximum flexibility.■ Keyed hold for optimum transmission of forces and moments.

�

Set besteht aus:2x

2x

2x2x

Items in set


page 15

MI connectors: Girder extension

Advantages■ Flexurally rigid extension/connection for MI girder.■ Built-in stop prevents the extension sliding right inside the girder.


Set besteht aus �:

8x8x

250

MI-90

Girder extension with connecting partsFor girder type Weight per ordering designation Item no. Package

set [kg] contents

MI-90 3.57 � MIC-90-E 304809 2MI-120 4.35 � MIC-120-E 304810 2

Set besteht aus �:

8x

4x 4x250

MI-120

�

�

Items in set �

Items in set �


page 16

Steel connectors with connecting partsFor girder type Steel beam width B C D Weight per Ordering designation Item no. Package

[mm] [mm] [mm] set [kg] contents

MI-90 75–165 – – 4.37 � MIC-S90-AA 304811 2MI-90 75–165 200 280 7.14 � MIC-S90-A 304812 2MI-90 165–235 300 350 8.59 � MIC-S90-B 304813 2MI-90 235–300 350 430 10.24 � MIC-S90-C 304814 2MI-120 75–165 200 280 7.54 � MIC-S120-A 304818 2MI-120 165–235 300 350 8.99 � MIC-S120-B 304819 2MI-120 235–300 350 430 10.65 � MIC-S120-C 304820 2

MI steel connectors: Connection to steel beams

Advantages■ For connection to standard steel beams without drilling or welding.■ Suitable for connection to flange or web.■ For use with MI-GC-M12 beam clamp.


B

155150

60 x 13

MI-90

12

B

CD

220

140

14

155150

60 x 13

12

BC

D

220

140

14

MI-120

�

Set besteht aus:2x

2x

300B

100

12140

MI-90

60 x 13 ��

Note: �Always to be supported at opposite end.

Note: � + �Designed for cantilever applications. May be supported at only one end.

Items in set


page 17

Steel connectors – welded bracket

For girder type Length L Steel beam width B C D Weight per Ordering designation Item no.[mm] [mm] [mm] [mm] set [kg] Recommended working load Fz [kN]

MI-90 500 75–165 200 280 10.18 4.660 2.970 � MIC-S90-A-500 267774MI-90 750 75–165 200 280 12.53 3.920 1.960 � MIC-S90-A-750 267775MI-90 1000 75–165 200 280 14.89 2.900 1.450 � MIC-S90-A-1000 267776MI-90 1500 75–165 200 280 19.61 1.850 0.920 � MIC-S90-A-1500 267777MI-90 2000 75–165 200 280 24.32 1.310 0.650 � MIC-S90-A-2000 267778

MI-90 500 165–235 300 350 11.63 4.660 2.970 � MIC-S90-B-500 267779MI-90 750 165–235 300 350 13.98 3.920 1.960 � MIC-S90-B-750 267780MI-90 1000 165–235 300 350 16.34 2.900 1.450 � MIC-S90-B-1000 267781MI-90 1500 165–235 300 350 21.06 1.850 0.920 � MIC-S90-B-1500 267782MI-90 2000 165–235 300 350 25.77 1.310 0.650 � MIC-S90-B-2000 267783

MI-90 500 235–300 350 430 13.29 4.230 2.110 � MIC-S90-C-500 267784MI-90 750 235–300 350 430 15.64 2.780 1.390 � MIC-S90-C-750 267785MI-90 1000 235–300 350 430 18.00 2.040 1.020 � MIC-S90-C-1000 267786MI-90 1500 235–300 350 430 22.72 1.280 0.640 � MIC-S90-C-1500 267787MI-90 2000 235–300 350 430 27.43 0.880 0.440 � MIC-S90-C-2000 267788

MI-120 500 75–165 200 280 11.76 4.640 3.610 � MIC-S120-A-500 267794MI-120 750 75–165 200 280 14.91 4.640 2.380 � MIC-S120-A-750 267795MI-120 1000 75–165 200 280 18.06 3.510 1.750 � MIC-S120-A-1000 267796MI-120 1500 75–165 200 280 24.36 2.230 1.110 � MIC-S120-A-1500 267797MI-120 2000 75–165 200 280 30.66 1.560 0.780 � MIC-S120-A-2000 267798

MI-120 500 165–235 300 350 13.21 4.640 2.960 � MIC-S120-B-500 267799MI-120 750 165–235 300 350 16.36 3.900 1.950 � MIC-S120-B-750 270459MI-120 1000 165–235 300 350 19.51 2.870 1.430 � MIC-S120-B-1000 270460MI-120 1500 165–235 300 350 25.81 1.810 0.900 � MIC-S120-B-1500 270461MI-120 2000 165–235 300 350 32.11 1.240 0.620 � MIC-S120-B-2000 270462

MI-120 500 235–300 350 430 14.87 4.640 2.320 � MIC-S120-C-500 270463MI-120 750 235–300 350 430 18.02 3.040 1.520 � MIC-S120-C-750 270464MI-120 1000 235–300 350 430 21.17 2.230 1.110 � MIC-S120-C-1000 270465MI-120 1500 235–300 350 430 27.47 1.230 0.690 � MIC-S120-C-1500 270466MI-120 2000 235–300 350 430 33.77 0.810 0.460 � MIC-S120-C-2000 270467

MI steel connectors: Connection to steel beams

Advantages■ For connection to standard steel beams without drilling or welding.■ Suitable for connection to flange or web.■ Lightweight for easy one man installation.


155150

60 x 13

12

BC

D

220

L

14

�

B

Fz1/2 1/2

Fz1/31/3

Fz1/3

155

60 x 13

12

B

D

C

220

L

14

�Note: � + �Designed for cantilever applications. May be supported at only one end.

Calculated by:Suitable Hilti beam clamps MI-GC-M12, Item No. 304894

FZFZ


page 18

Concrete connector with connecting partsFor girder type Weight per Ordering designation Item no Package

set [kg] contents

MI-90 3.51 � MIC-C90-AA 304825 2MI-90 7.32 � MIC-C90-D 304827 2MI-120 7.69 � MIC-C120-D 304829 2

MI concrete connectors: Connection to concrete

Advantages■ Four elongated holes for easy wall mounting.■ Designed for ceiling, wall and floor mounting.


Set besteht aus:2x

2x

100

140 200

12

MI-90156

47 x 17

15

156

230

MI-90

230

140

156

47 x 17

15

156

230

230

140

� � �

Note: �Always to be supported at opposite end.


Items in set


page 19

Concrete connector – welded bracket

For girder type Length L Weight per Ordering designation Item no.[mm] set [kg] Recommended working load Fz [kN]

MI-90 500 10.60 9.380 4.690 � MIC-C90-D-500 267789MI-90 750 12.95 6.210 3.100 � MIC-C90-D-750 267790MI-90 1000 15.31 4.610 2.300 � MIC-C90-D-1000 267791MI-90 1500 20.03 3.000 1.500 � MIC-C90-D-1500 267792MI-90 2000 24.74 2.160 1.080 � MIC-C90-D-2000 267793

MI-120 500 12.18 10.000 5.320 � MIC-C120-D-500 270468MI-120 750 15.33 7.040 3.520 � MIC-C120-D-750 270469MI-120 1000 18.48 5.230 2.610 � MIC-C120-D-1000 270470MI-120 1500 24.78 3.380 1.690 � MIC-C120-D-1500 270471MI-120 2000 31.08 2.420 1.210 � MIC-C120-D-2000 270472


Anchor Calculated by:Approved Hilti HST(R) M16 anchors; alternative approved Hilti anchors are the Hilt HVZ, HIT-TZ(R) of thesame nominal diameter and same version.

MI concrete connectors: Connection to concrete

Advantages■ Four elongated holes for easy wall mounting.■ Designed for ceiling, wall and floor mounting.■ Lightweight for easy one man installation.


156

47 x 17

15

156

230

230

L

156

47 x 17

15

156

230

230

L

� �

Fz1/2 1/2

Fz1/31/3

Fz1/3

FZFZ


page 20

Concrete wall connector with connecting partsFor girder type Weight per Ordering designation Item no. Package

set [kg] contents

MI-90 2.29 � MIC-C90-U 304826 2

MI concrete connectors: Connection to concrete walls

Advantages■ Lighter version for structures supported at both ends.■ Elongated holes for easier positioning.■ Simple support for installation between two walls.


Set besteht aus:1x

1x

100

25 x 14

8150

200

100

MI-90

�

NoteAlways to be supported at opposite end.

Items in set


page 21

MI connectors: Multi-angle connectors

Advantages■ For supports / corner struts at angles between 0° and 180°.■ For connecting directly to standard steel beams or concrete.


MI angle connectors for girder, with connecting parts


MI-90/MI-120 2.53 � MIC-U-MA 304806 2

MI angle connectors for steel, with connecting parts

For girder type Steel beam width B C D Weight per Ordering designation Item no. Package[mm] [mm] [mm] set [kg] contents

MI-90/MI-120 75–165 200 280 6.29 � MIC-SA-MA 304815 4MI-90/MI-120 165–235 300 350 7.74 � MIC-SB-MA 304816 2MI-90/MI-120 235–300 350 430 9.40 � MIC-SC-MA 304817 2

MI angle connectors for concrete, with connecting parts


MI-90/MI-120 2.04 � MIC-CU-MA 304828 4

197,5

130

80

8120

12.5

Set besteht aus:

2x

2x

Set besteht aus:

Set besteht aus:

100

155220

B

C

D

80

12

12.5

1460 x 13

6

�

�

100

100

6

80

8 200

12.5

25 x 14

150

�

Items in set

Items in set

Items in set

�

�


page 22

MI steel / concrete connectorsBase plates for steel / concrete

Advantages■ All steel beam widths from 75–300 mm covered by only 3 plate

sizes.


�

155

150

60 x 13

12

BC

D

220

14

156

47 x 17

15

156

230

230

�MI base plates for steel /concrete, without connecting partsFor girder type Steel beam width B C D Weight per Ordering Item no. Package

[mm] [mm] [mm] set [kg] designation contents

MI-90/MI-120 75–165 200 280 5.46 � MIB-SA 304821 2MI-90/MI-120 165–235 300 350 6.91 � MIB-SB 304822 2MI-90/MI-120 235–300 350 430 8.57 � MIB-SC 304823 2MI-90/MI-120 For connection to concrete 5.88 � MIB-CD 304830 2


page 23

MI basic connector for welding, without connecting parts


MI- 90 1.44 � MIC-SC90 304824 2MI-120 1.81 � MIC-SC120 304808 2

Flexy pack: Adaptable connectorfor steel or concrete

Advantages■ The girder connection point can be positioned as desired

for special cases.■ Supplied in a primer finish for trouble-free welding.

Can be galvanized later if desired.

Technical dataMaterial: S235 JRG2 as per DIN EN 10 025Corrosion protection: None (primer coating-basic connector)

72

72

140

101

71

140� �

Flexy pack – connector for welding as desired, without connecting parts

Parts listOrdering designation Item no. Info Position

MIC-SC90 or MIC-SC120 304824 or 304808 Pos.1MIB-SA or MIB-SB 304821/304822 Depending on base material Pos.2MIB-SC or MIB-CD 304823/304830 or size of steel beam

Pos. 2

Pos. 1


page 24

49

15

28,5

400

96

6

177,5 x 13

35 x 13

MI U-bolt clamps with connecting partsFor girder type Weight per Ordering designation Item no. Package

set [kg] contents

MI-90 1.26 � MIC-UB90 304831 10*MI-90 2.58 � MIC-UB90 L400 304832 2MI-120 1.38 � MIC-UB120 304833 10*MI-90 1.24 � MIC-UB90-M16 304834 6*MI-120 1.36 � MIC-UB120-M16 304835 6*

*numbers of pairs in set

Advantages■ Reliable fastening system for U-bolts.■ Elongated holes for full adjustment of pipe position.■ Keyed hold for optimum transmission of forces.

Technical data for the clamping systemMaterial: S235 JRG2 as per DIN EN 10 025Galvanizing: Hot-dip galvanized 55 µmConnecting screws: M12 (connection to MI-girder)

90

90

65 x 13 49

26 x 13,5

96

90

65 x 13 49

26 x 13,596

90

65 x 17 49

26 x 13,5

� � ��

Pipe clamps: U-bolt clamps for uninsulated pipes

Set : besteht aus:

2x

2x 2x

2x2x

Set : besteht aus:

2x

1x

2x 2x 2x

90

90

65 x 17 49

26 x 13,5

�

��Items in set ��

Items in set �


page 25

U-bolts with connecting partsNominal size Pipe outside d1 b2 h Shank d3 e Weight Ordering designation Item no. Package

diameter Da dia. each contentsNW [mm] [mm] [mm] [mm] [mm] [mm] [kg]

25 33.7 38 50 76 10 M10 48 0.13 MI-UB 25-M10 304870 540 48.3 52 50 92 10 M10 62 0.16 MI-UB 40-M10 304871 550 60.3 64 50 109 12 M12 76 0.24 MI-UB 50-M12 304872 565 76.1 82 50 125 12 M12 94 0.27 MI-UB 65-M12 304873 580 88.9 94 50 138 12 M12 106 0.29 MI-UB 80-M12 304874 5

100 114.3 120 60 171 16 M16 136 0.64 MI-UB 100-M16 304875 5125 139.7 148 60 191 16 M16 164 0.72 MI-UB 125-M16 304876 3150 168.3 176 60 217 16 M16 192 0.80 MI-UB 150-M16 304877 3200 219.1 228 70 283 16 M16 244 1.01 MI-UB 200-M16 304878 3250 273.0 282 70 334 16 M16 298 1.19 MI-UB 250-M16 304879 3

Pipe clamps: MI U-bolts for uninsulated pipes

Advantages■ Small contact surface between U-bolt and pipe.■ Minimizes crevice corrosion.■ In compliance with DIN standard for U-bolts.

Technical data for the clamping systemMaterial: S235 JRG2 as per DIN EN 10025Galvanizing: Hot-dip galvanized 45 µmTemperatures: 300 °C

h

b2

d3e

d1


page 26

Nominal Pipe outside B s F W H L L1 Clamping Weight per Permissible loads Ordering designation Item no. Packagesize diameter Da screw set Fx +Fz –Fz Fy contentsNW [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [kg] (kN) (kN) (kN) (kN)

25 33.7 30 6 9 80 85 250 – M10 2.8 0.4 0.8 0.3 0.3 � MI-PS1/1 25-85 304844 225 33.7 30 6 8 82 140 250 – M10 2.4 0.4 0.8 0.3 0.3 � MI-PS1/1 25-140 286957 240 48.3 30 6 9 80 85 250 – M10 2.8 0.5 1.0 0.3 0.3 � MI-PS1/1 40-85 304845 240 48.3 30 6 8 82 140 250 – M10 2.4 0.5 1.0 0.3 0.3 � MI-PS1/1 40-140 286958 250 60.3 40 6 9 80 85 250 – M12 3.2 0.9 1.8 0.6 0.6 � MI-PS1/1 50-85 304846 250 60.3 40 6 8 82 140 250 – M12 2.7 0.9 1.8 0.6 0.6 � MI-PS1/1 50-140 286959 265 76.1 40 6 9 80 85 250 – M12 3.3 1.1 2.1 0.7 0.7 � MI-PS1/1 65-85 304847 265 76.1 40 6 8 82 140 250 – M12 2.8 1.1 2.1 0.7 0.7 � MI-PS1/1 65-140 286960 280 88.9 40 6 9 80 85 250 – M12 3.3 1.2 2.3 0.8 0.8 � MI-PS1/1 80-85 304848 280 88.9 40 6 8 82 140 250 – M12 2.9 1.2 2.3 0.8 0.8 � MI-PS1/1 80-140 286961 2

100 114.3 40 8 9 80 85 250 – M12 3.8 2.5 5.0 1.7 1.7 � MI-PS1/1 100-85 304849 2100 114.3 40 8 8 80 140 250 – M12 3.4 2.5 5.0 1.7 1.7 � MI-PS1/1 100-140 286962 2125 139.7 40 8 9 80 85 250 – M12 4.0 2.9 5.8 1.9 1.9 � MI-PS1/1 125-85 304850 2125 139.7 40 8 8 80 140 250 – M12 3.6 2.9 5.8 1.9 1.9 � MI-PS1/1 125-140 286963 2150 168.3 40 8 9 80 85 250 – M12 4.2 3.2 6.4 2.1 2.1 � MI-PS1/1 150-85 304851 2150 168.3 40 8 8 80 140 250 – M12 3.8 3.2 6.4 2.1 2.1 � MI-PS1/1 150-140 286964 2

25 21.3 30 5 9 80 85 250 200 M10 3.3 0.8 1.5 0.5 0.5 � MI-PS2/1 25-85 304852 225 21.3 30 5 9 80 140 250 180 M10 3.7 0.8 1.5 0.5 0.5 � MI-PS2/1 25-140 286965 240 48.3 30 5 9 80 85 250 200 M10 3.4 1.0 2.0 0.7 0.7 � MI-PS2/1 40-85 304853 240 48.3 30 5 9 80 140 250 180 M10 3.8 1.0 2.0 0.7 0.7 � MI-PS2/1 40-140 286966 250 60.3 40 6 9 80 85 250 190 M12 4.1 1.8 3.5 1.2 1.2 � MI-PS2/1 50-85 304854 250 60.3 40 6 9 80 140 250 180 M12 4.5 1.8 3.5 1.2 1.2 � MI-PS2/1 50-140 286967 265 76.1 40 6 9 80 85 250 190 M12 4.3 2.1 4.2 1.4 1.4 � MI-PS2/1 65-85 304855 265 76.1 40 6 9 80 140 250 180 M12 4.7 2.1 4.2 1.4 1.4 � MI-PS2/1 65-140 286968 280 88.9 40 6 9 80 85 250 190 M12 4.4 2.4 4.7 1.6 1.6 � MI-PS2/1 80-85 304856 280 88.9 40 6 9 80 140 250 180 M12 4.8 2.4 4.7 1.6 1.6 � MI-PS2/1 80-140 286969 2

100 114.3 40 8 9 80 85 250 190 M12 5.3 3.0 6.0 2.0 2.0 � MI-PS2/1 100-85 304857 2100 114.3 40 8 9 80 140 250 180 M12 5.8 3.0 6.0 2.0 2.0 � MI-PS2/1 100-140 286970 2125 139.7 40 8 9 80 85 250 190 M12 5.7 3.5 7.0 2.3 2.3 � MI-PS2/1 125-85 304858 1125 139.7 40 8 9 80 140 250 180 M12 6.1 3.5 7.0 2.3 2.3 � MI-PS2/1 125-140 286971 1150 168.3 40 8 9 80 85 250 190 M12 6.1 4.0 8.0 2.7 2.7 � MI-PS2/1 150-85 304859 1150 168.3 40 8 9 80 140 250 180 M12 6.6 4.0 8.0 2.7 2.7 � MI-PS2/1 150-140 286972 1200 219.1 50 8 9 100 107 250 180 M16 8.5 4.8 9.5 3.2 3.2 � MI-PS2/1 200-107 304860 1200 219.1 50 8 9 100 142 250 180 M16 8.9 4.8 9.5 3.2 3.2 � MI-PS2/1 200-142 286973 1250 273.0 50 8 9 100 107 250 180 M16 9.5 5.3 10.5 3.5 3.5 � MI-PS2/1 250-107 304861 1250 273.0 50 8 9 100 142 250 180 M16 9.9 5.3 10.5 3.5 3.5 � MI-PS2/1 250-142 286974 1300 323.9 50 8 9 100 107 250 180 M16 10.5 5.8 11.5 3.8 3.8 � MI-PS2/1 300-107 304862 1300 323.9 50 8 9 100 142 250 180 M16 10.9 5.8 11.5 3.8 3.8 � MI-PS2/1 300-142 286975 1

* The maximum permissible loads for connecting components must be taken into account when the pipe support is used!

MI pipe clamps: Pipe supports for insulated pipes

Advantages■ With mounting holes for installing light-duty fixed points.

Technical data for the clamping systemMaterial: S235 JRG2 as per DIN EN 10025Galvanizing: Hot-dip galvanized 70 µmTemperatures: Up to 300 °C

8

5

75

L

F

W

s

Da

B

H

13

Fy

Fx

– Fz

+ Fz

L

F

W

sDa

B

L1

H

13

Fy

Fx

– Fz

+ Fz

L

F

W

sDa

B

L1

H

13

Fy

Fx

– Fz

+ Fz

1 ring / 1 rib for DN25-DN150

Low-friction plate

2 rings / 1 rib for DN25-DN300

Sliding support clamps

Heavy-duty version for DN200-DN600

Fixed point

� � �


page 27

Nominal Pipe outside B s F W H L L1 Clamping Weight per Permissible loads Ordering designation Item no. Packagesize diameter Da screw set Fx +Fz –Fz Fy contentsNW [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [kg] (kN) (kN) (kN) (kN)

200 219.1 50 8 8 175 107 290 260 M16 12.4 – 12.0 4.0 4.0 � MI-PS2/2 200-107 304863 1200 219.1 50 8 8 175 142 290 260 M16 15.5 – 12.0 4.0 4.0 � MI-PS2/2 200-142 286976 1250 273.0 50 8 8 175 107 290 260 M16 13.2 – 15.0 5.0 5.0 � MI-PS2/2 250-107 304864 1250 273.0 50 8 8 175 142 290 260 M16 16.3 – 15.0 5.0 5.0 � MI-PS2/2 250-142 286977 1300 323.9 50 8 8 175 107 290 260 M16 14.0 – 16.0 5.3 5.3 � MI-PS2/2 300-107 304865 1300 323.9 50 8 8 175 142 290 260 M16 17.0 – 16.0 5.3 5.3 � MI-PS2/2 300-142 286978 1350 355.6 60 8 10 175 142 290 250 M16 19.2 – 17.8 5.9 5.9 � MI-PS2/2 350-142 304866 1350 355.6 60 8 10 175 192 290 250 M16 21.4 – 17.8 5.9 5.9 � MI-PS2/2 350-192 286979 1400 406.4 60 8 10 250 142 290 250 M16 24.9 – 18.7 6.0 6.0 � MI-PS2/2 400-142 304867 1400 406.4 60 8 10 250 192 290 250 M16 27.9 – 18.7 6.0 6.0 � MI-PS2/2 400-192 286980 1500 508.0 70 10 10 250 142 290 240 M20 33.5 – 21.3 6.0 6.0 � MI-PS2/2 500-142 304868 1500 508.0 70 10 10 250 192 290 240 M20 36.5 – 21.3 6.0 6.0 � MI-PS2/2 500-192 286981 1600 610.0 70 10 10 250 142 290 240 M20 36.8 – 28.0 6.0 6.0 � MI-PS2/2 600-142 304869 1600 610.0 70 10 10 250 192 290 240 M20 38.8 – 28.0 6.0 6.0 � MI-PS2/2 600-192 286982 1

* The maximum permissible loads for connecting components must be taken into account when the pipe support is used!

MI pipe clamps: Pipe supports for insulated pipes

Advantages■ With mounting holes for installing light-duty fixed points.

Technical data for the clamping systemMaterial: S235 JRG2 as per DIN EN 10025Galvanizing: Hot-dip galvanized 70 µmTemperatures: Up to 300 °C

8

5

75

L

F

W

s

Da

B

H

13

Fy

Fx

– Fz

+ Fz

L

F

W

sDa

B

L1

H

13

Fy

Fx

– Fz

+ Fz

L

F

W

sDa

B

L1

H

13

Fy

Fx

– Fz

+ Fz

1 ring / 1 rib for DN25-DN150

Low-friction plate

2 rings / 1 rib for DN25-DN300

Sliding support clamps

Heavy-duty version for DN200-DN600

Fixed point

� � �


page 28

Advantages■ Pipe ring support free to move in one direction.■ Fully adjustable.■ Spacer plates permit use of pipe supports with

base plates of greater thickness.

Technical data for the clamping systemMaterial: S235 JRG2 as per DIN EN 10 025Galvanizing: Hot-dip galvanized 45 µm

12

90

45

18130

102

M12

12

120

45

18130

102

M12

� �

4

102

30130

13

16

6

102

30

18

130

13� �

�

MI pipe clamps: MI sliding support clamping system for insulated pipes


MI-90 1.80 � MIC-PS90 304838 4*MI-120 1.88 � MIC-PS120 304839 4*MI-90/MI-120 0.22 � MIC-PSP-4MM 283593 10*MI-90/MI-120 0.34 � MIC-PSP-6MM 283594 10**Number of pairs in package


MI-90/MI-120 0.1 � MIC-PG 304842 108

5

75

MI clamping system for sliding support, with connecting parts

MI low-friction system for sliding support

Technical data for low-friction systemMaterial: PE-UH MWFriction value: µ = 0,15Temperature resistance: –273,15 °C to +90 °C


page 29

126

M12

102

156

M12

102� �

Advantages■ Quickly and easily installed pipe support system for light-duty fixed

points.

MI clamping system for fixed points, with connecting partsFor girder type Weight per Ordering designation Item no. Package

set [kg] contents

MI-90 0.60 � MIA-B090-M12 304840 8*MI-120 0.68 � MIA-B0120-M12 304841 8*

*Number of pairs in package

MI pipe clamps: MI rigid support clamping system,with connecting parts

Technical data for the clamping systemMaterial: S235 JRG2 as per DIN EN 10025Galvanizing: Hot-dip galvanized 45 µm


page 30

For girder type Weight per Suitable pipe Ordering designation Item no. Packageset [kg] diameter [mm] contents

MI-90/MI-120 5.50 219 ÷ 406 MI-DPR 304880 1

MI pipe clamps:Twin roller support

Advantages■ Dimensions suitable for fastening to MI-girder with MIC-PA90

or MIC-PA120.

Technical data:Body material: S235 JRG2 as per DIN EN 10 025Roller material: S355 JO as per DIN EN 10 025Axle material: Stainless steel (1.4541)Rated load capacity: 15 kNCoefficient of friction: 0.035

2x 2x

2x2x

Set besteht aus:

86

130

8

190

225

E

DA

Items in set

90

10210

M12

150

Adaptor plate with connecting partsFor girder type Weight per Ordering designation Item no. Package

set [kg] contents

MI-90 3.38 � MIC-PA90 304836 2MI-120 3.46 � MIC-PA120 304837 2

Advantages■ The adaptor plate takes the place of the steel beam flange and thus

permits the use of conventional clamping systems for pipe supports.

Technical data for the clamping systemMaterial: S235 JRG2 as per DIN EN 10 025Galvanizing: Hot-dip galvanized 55 µm

�

120

10210

150

M12

�

MI pipe clamps: Adaptor plate forpipe support clamping system,incl. connecting parts

DA = Outside-diameter pipe

E = 0.532 x DA + 54


page 31

MI pipe clamps: Plate for weld-on tabs

Advantages■ Easy installation of standard weld-on tabs, e.g. for spring hangers.

Technical data for the clamping systemMaterial: S235 JRG2 as per DIN EN 10 025Galvanizing: U-bolt galvanized 45µm,

plate with primer finish


MI-90 1.01 � MIC-SPH-90 304843 4MI-120 1.10 � MIC-SPH-120 283592 4

90

12

M12

60

130

120

12

M12

60

130

� �

��


page 32

For girder type Weight per Ordering designation Item no. Packegeset [kg] contents

MI-90 0,16 � MIA-EH90 304887 10MI-120 0,19 � MIA-EH120 304888 10MI-90 0,10 � MIA-OH90 304889 10MI-120 0,13 � MIA-OH120 304890 10MI-90, MI-120 0,28 � MIA-EH-P 304891 10MI-90, MI-120 0,02 � M12-F hex.collar nut 283589 50MI-90, MI-120 0,06 � MIA-TP 305707 20MI-90, MI-120 0,10 Hex.head screw M12�120-F/8.8 283595 40MI-90, MI-120 0,11 Hex.head screw M12�130-F/8.8 283596 40MI-90, MI-120 0,005 A 13-F washer 304771 100

MI accessories: Individual connecting parts

Advantages■ Parts designed for easy assembly with one hand (shaped to prevent

rotation).■ “Easy hand” plate (5) for easy single-handed adjustment of the con-

nection.

Technical dataMaterial: EN-GJMW-400-5 as per DIN EN 1562Screws: 8.8 grade Nuts: 8 grade DIN 1661, self lockingGalvanizing: 45 µm

120

M12

36,6

36,6

150

M12

36,6

36,6

95

M12 127

M12

72

50

12M12

26

12,2 x 12,2

36,6 36,6

7

�

�

�

�

�

�

�

Examples of applications (cantilever)

Assembly procedure

1.

2.

2-3x

1.2.

1 2

3 4


page 33

MI accessories: End caps

Advantages■ Ends of girder closed securely.■ With built-in opening to permit drainage of liquids.

Technical dataMaterial: Moplen EP 240HTemperature resistance: –30° to +90° C

For girder type Weight Ordering designation Item no. Package [kg] contents

MI-90 0.03 � MIA-EC-90 304892 25MI-120 0.04 � MIC-EC-120 304893 25

� �

18.5

96

96

18.5

126

96


page 34


MI-90/MI-120 0.27 � MI-GC-M12 304894 16MI-90/MI-120 0.03 � MI-GCD-6MM 283590 16MI-90/MI-120 0.07 � MI-GCD-12MM 283591 16

MI accessories: Beam clamps for various flange thicknesses

Advantages■ For steel beams with a flange thickness of 3 -12 mm and angle of

up to 15°.■ Spacers for use with flange thicknesses greater than 12 mm.

Note■ The flat nose must be positioned against the steel beam and the

round nose on the connecting part or spacer.

Technical dataMaterial: EN-GJMW-400-5 as per DIN EN 1562Galvanizing: Hot-dip galvanized 55 µmScrews: 8.8 grade

M12

M12 x 85

30

12

3830

6

3830

�

� �


page 35


page 36

MI / MQ connectors with connecting partsFor channel Weight per Ordering designation Item no. Package

set [kg] contents

MQ-41, MQ-21D 0.36 � MIC-MI/MQ-X 304881 16all MQ single channels 0.05 � MIC-MI/MQ-M8 304882 5

MI / MQ connector

Advantages■ Direct connection to components of the Hilti MQ system.■ Keyed hold for optimum transmission of forces and moments.


250

41

47

4

61 x 11

5

12

M8x16SW13

�

�

�

Set besteht aus:

2x

4x

2x

Set besteht aus:

Items in set

Items in set

Assembly procedure

2.

1.M8x16

1 2

Description Size Ordering designation Item no. Package contents

Magnetic wrench SW 13 � MQZ-SVS 369693 1

200 mm

SW 13mit MagneteinsatzSW 13with magnetic insert


page 37

MQV-UB U-bolt pipe clamp for MQ system

Advantages■ Easy installation of U-bolts.■ Fastened with wing nuts or hex. nuts.

Technical dataMaterial: S235JR as per DIN EN 10025Galvanizing: hot-dip galvanized, approx. 55 µm

47530

37

1113

MQV-PS pipe support for MQ system

55

37

12

25

94

4

11

Advantages■ Easy installation as guide-type pipe support.■ Fastened with wing nuts or hex. nuts.

Technical dataMaterial: S235JR as per DIN EN 10025Galvanizing: hot-dip galvanized, approx. 55 µm

MQP-U universal joint

For D1 D2 Weight each Ordering Item no. Package[mm] [mm] [g] designation contents

M12 12,5 12,5 390 MQP-U M12 284248 10M16 16,5 16,5 390 MQP-U M16 284249 10

Item no. Max. recommended load Tightening torque MD[kN] [Nm]

MQP-U M12 14 20MQP-U M16 14 20

MQP-45°-F base material connectorFor channel Weight each Ordering designation Item no. Package

[g] contents

MQ-21-F, MQ-41-F 350 MQP-45°-F 304164 1105

4241

14

45°

For channel Weight per Ordering designation Item no. Packageset [g] contents

MQ-41-F, MQ-41D-F, MQ-52-72D-F 70 MQV-UB-M12 304884 5** Number of pairs in package

For channel Weight each Ordering designation Item no. Package[g] contents

MQ-41-F, MQ-41D-F, MQ-52-72D-F 70 MQV-PS 304886 1** Number of pairs in package


page 38

Example of applicationOpposite cantilever arms at same or similar height

Parts listQuantity Ordering designation Item no. Info Position

2 MIC-90-L-AP 305710 Cantilever connectors Pos. 12 MIC-EH-90 304887 Pos. 22 MIA-TP 305707 Pos. 34 MIA-OH90 304889 Pos. 46 M12-F hex. collar nut 283589 Self-locking nuts Pos. 5

Pos. 1

Pos. 3 Pos. 5

Pos. 4

Pos. 2

Example of applicationGirder connection to steel beam

Pos. 1

Pos. 2

Pos. 3Pos. 4

Beam height up to about 320 mm.

Parts list (beam height up to 320 mm)Quantity Ordering designation Item no. Info Position

1 MIC-S*(A/B/C) 304812/304813/304814 To suit beam size Pos. 11 MIB-S* 304821/ 304822/ 304823 Size as (1) Pos. 24 AM 12-F 304774 M12-F threaded rod Pos. 38 M12-F hex. collar nut 283589 Self-locking nuts Pos. 4*Plate size to be selected to suit width between flanges

Advantages■ Girder can be connected to steel beam without welding.


page 39

Pos. 1

Pos. 3

Pos. 5

Pos. 2

Pos. 4

Beam height greater than 320 mm.Further connections using MIC-90-L cantilever connector.

Parts list (beam height greater than 320 mm)Quantity Ordering designation Item no. Info Position

2 MI-90 304799 Length to suit beam size Pos.18 MIC-UB90-M12 304831 Pos.24 Hex.head screw M12�120F/ 8.8 283595 Pos.3

12 M12-F hex. collar nut 283589 Self-locking nuts Pos.44 AM 12-F 304774 M12-F threaded rod Pos.5

Parts listQuantity Ordering designation Item no. Info Position

1 MIB-SA 304821 Pos. 14 MIA-EH-P 304891 Pos. 24 A13-F 304771 Pos. 34 M12�130F/8.8 hex screw 283596 Pos. 44 M12 hex. collar nut 283589 Self-locking nut Pos. 5

Example of applicationCross connection between MI girder

Pos. 1 Pos. 4

Pos. 3

Pos. 5

Pos. 2

Pos. 5

Advantages■ Keyed hold for optimum transmission of forces and moments.

Hilti MI industrial pipe support system Technical ... · Hilti MI industrial pipe support system...

Documents

Transcript of Hilti MI industrial pipe support system Technical ... · Hilti MI industrial pipe support system...