High Quality European based Manufacturers BS-413en]file.pdf · bs-413 en 50130-4, en 55022, en...

4
921413000_09_005 Page 1 from 4 13,6- 14,8V DC 6mA Bayblend FR3010, clear polycarbonate (red) USAGE BATTERY TYPE For external use 12V/1,3Ah Pb ( sealed lead-acid) IP 34 115 dB / 1m -10 60 C o έως Up to 95% 2 years 1700gr. 290x95x190mm BS-413 EN 50130- 4, EN 55022, EN 60950-1 Technical characteristics RELATIVE HUMIDITY CONSTRUCTION MATERIAL WEIGHT EXTERNAL DIAMENSIONS GUARANTEE OPERATION VOLTAGE QUIESCENT CONSUMPTION SOUND LEVEL PRODUCED IN ACCORDANCE WITH OPERATION TEMPERATURE RANGE DEGREES OF COVER PROTECTION Autonomous electronic siren with beacon for burglar alarm panels Thank you for purchasing this product of Olympia tampered with. Electronics. A European manufacturer. If you require, the siren to also be activated if the siren is dismounted from the wall. you must Description connect the T1, T2 (TAMPER) inputs. The BS-413 alarm siren is of robust design and In case of maintenance or if the siren is moved can be used with conventional burglar alarm from it’s mounting position, the SE (Service) panels such as the BS-468. It has a red beacon input of the siren must be connected to the (-) of that blinks when the siren is activated and a the panel and the panel must be set to OFF. piezo speaker that produces a sound level of 115dB at 1 meter. Battery The incorporated tamper mechanism protects If the battery has not been connected then the the siren from unauthorized access when the siren produces a single tone sound every 1 cables are cut, the cover is removed or when second. the siren is unmounted from the wall. Whereas if the battery does not operate correctly, a 3 tone sound is emitted every 12 Mounting hours. It is mounted externally on a flat surface and at a height of about 2,5 meters. Also it should be Beacon placed in an area that does not obstruct the There is a two position (ON, OFF) jumper on the sound. siren which is marked (LED FLASΗ). If a link is placed on the (ON) position, the beacon blinks WARNING!!! every 4 seconds in the quiescent state. If no All 4 mounting screws must be used. jumper is placed then the beacon is OFF during the quiescent state and blinks during the alarm. Connection The connection between the siren and the BS- Start signal 468 panel is shown on figure 1. There is also another 2 position jumper marked After finishing with the connections, connect the (TRIGGER) with the positions (-) and (+). battery cables, install the internal cover and the This jumper sets if the trigger in positive or front fascia of the siren by installing the screws negative. Α positive trigger means that the ST on the bottom side. Finally remove the cable (START) signal must be a positive voltage for connected to the SE (Service) of the siren from the siren to be activated. the (-) of the panel. The siren will sound once to indicate that it is ready to operate and receive a command from the panel. The siren now charges the battery and is ready to accept an ALARM signal from the panel or if the cables are cut. If we connect the Τ1, Τ2 (TAMPER) signals then it will be activated if it is High Quality European based Manufacturers

Transcript of High Quality European based Manufacturers BS-413en]file.pdf · bs-413 en 50130-4, en 55022, en...

921413000_09_005Page 1 from 4

13,6-14,8V DC

6mA

Bayblend FR3010, clear polycarbonate (red)

USAGE

BATTERY TYPE

For external use

12V/1,3Ah Pb (sealed lead-acid)

IP 34

115 dB / 1m

-10 60 Coέως

Up to 95%

2 years

1700gr.

290x95x190mm

BS-413

EN 50130-4, EN 55022, EN 60950-1

Technical characteristics

RELATIVE HUMIDITY

CONSTRUCTION MATERIAL

WEIGHT

EXTERNAL DIAMENSIONS

GUARANTEE

OPERATION VOLTAGE

QUIESCENT CONSUMPTION

SOUND LEVEL

PRODUCED IN ACCORDANCE WITH

OPERATION TEMPERATURE RANGE

DEGREES OF COVER PROTECTION

Autonomous electronic siren with beacon for burglar alarm panels

Thank you for purchasing this product of Olympia tampered with.Electronics. A European manufacturer. If you require, the siren to also be activated if the

siren is dismounted from the wall. you must Description connect the T1, T2 (TAMPER) inputs.The BS-413 alarm siren is of robust design and In case of maintenance or if the siren is moved can be used with conventional burglar alarm from it’s mounting position, the SE (Service) panels such as the BS-468. It has a red beacon input of the siren must be connected to the (-) of that blinks when the siren is activated and a the panel and the panel must be set to OFF.piezo speaker that produces a sound level of 115dB at 1 meter. BatteryThe incorporated tamper mechanism protects If the battery has not been connected then the the siren from unauthorized access when the siren produces a single tone sound every 1 cables are cut, the cover is removed or when second.the siren is unmounted from the wall. Whereas if the battery does not operate

correctly, a 3 tone sound is emitted every 12 Mounting hours.It is mounted externally on a flat surface and at a height of about 2,5 meters. Also it should be Beaconplaced in an area that does not obstruct the There is a two position (ON, OFF) jumper on the sound. siren which is marked (LED FLASΗ). If a link is

placed on the (ON) position, the beacon blinks WARNING!!! every 4 seconds in the quiescent state. If no All 4 mounting screws must be used. jumper is placed then the beacon is OFF during

the quiescent state and blinks during the alarm.ConnectionThe connection between the siren and the BS- Start signal468 panel is shown on figure 1. There is also another 2 position jumper marked After finishing with the connections, connect the (TRIGGER) with the positions (-) and (+). battery cables, install the internal cover and the This jumper sets if the trigger in positive or front fascia of the siren by installing the screws negative. Α positive trigger means that the ST on the bottom side. Finally remove the cable (START) signal must be a positive voltage for connected to the SE (Service) of the siren from the siren to be activated.the (-) of the panel. The siren will sound once to indicate that it is ready to operate and receive a command from the panel. The siren now charges the battery and is ready to accept an ALARM signal from the panel or if the cables are cut. If we connect the Τ1, Τ2 (TAMPER) signals then it will be activated if it is

High Quality European based Manufacturers

Alarm Alarm durationThe siren sounds the alarm in 2 cases, when The siren is activated for as long as an alarm the ST (START) signal is activated or when it’s signal is issued but stops after 7 minutes. The power is interrupted. siren will be reactivated with a new alarm signal.

A total of 7 cables are needed for connecting the siren. 2 cables are needed for connecting the siren power supply. The third cable is used for the ST (START) signal. The fourth cable is the signal for the beacon FL (FLASH), which in not mandatory for the operation of the siren. The fifth cable is for the SE (SERVICE) signal that prevents the siren from sounding during the installation. It must be connected during the connection procedure and disconnected (from the panel side) after the installation has finished. The remaining 2 cables are used for connecting the T1, T2 (TAMPER) inputs of the siren to the Ζ8 zone TAMPER of the panel. This method permits the siren to sound if tampered with and will also activate the auto telephone dialer.

1. Mounting points (All four screws must be used) 2. Inner cover mounting points3. Piezo megaphone4. Connection terminals5. Battery compartment 12V/1,2Ah6. TAMPER protection mechanism7. Beacon 8. Cable entry hole

Figure 2. The main parts of the siren

11

1

1

2

6

2

7

3

4

5

8

Jumpers

921413000_09_005Page 2 from 4

Installation Instructions

Connections

Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 12V12V A B P1 P2 P3 AS ES NO C NC ANT

5K

6

Siren BS-413

Figure 1. Connecting a BS-413 siren to the BS-468 panel

Remove thiscable after the installation

has finished

24_HC C

12V ALARM RELAYSIRENS

NOCNCTC

EXT AUTO

Remove thiscable after the installation

has finished

SirenBS-413

Figure 2. Connecting a BS-413 siren to the BS-418 panel

921413000_09_005Page 3 from 4

SE

T1

T2

+

+

-

++ ST SE T1 T2FL

Figure 3. Connecting a BS-413 siren to the BS-458 panel

Remove thiscable after the installation

has finished

BS-458

N L P2

P1

Z1

Z2

Z3

Z4

AS

TAMP

ER

-12V - - - -

+12V

Siren BS-413

++ ST SE T1 T2FL

5K

6

921413000_09_005Page 4 from 4