GE Fanuc Automation - Motortong.com SAFETY PRECAUTIONS s-1 SAFETY PRECAUTIONS This "Safety...

of 134/134
GE Fanuc Automation Computer Numerical Control Products AC Spindle Motor α α αiB Series Descriptions GFZ-65292EN/03 March 2003
  • date post

    19-Mar-2018
  • Category

    Documents

  • view

    290
  • download

    14

Embed Size (px)

Transcript of GE Fanuc Automation - Motortong.com SAFETY PRECAUTIONS s-1 SAFETY PRECAUTIONS This "Safety...

  • GE Fanuc Automation

    Computer Numerical Control Products

    AC Spindle Motor iB Series Descriptions GFZ-65292EN/03 March 2003

  • GFL-001

    Warnings, Cautions, and Notesas Used in this Publication

    Warning

    Warning notices are used in this publication to emphasize that hazardous voltages, currents,temperatures, or other conditions that could cause personal injury exist in this equipment ormay be associated with its use.

    In situations where inattention could cause either personal injury or damage to equipment, aWarning notice is used.

    Caution

    Caution notices are used where equipment might be damaged if care is not taken.

    NoteNotes merely call attention to information that is especially significant to understanding andoperating the equipment.

    This document is based on information available at the time of its publication. While effortshave been made to be accurate, the information contained herein does not purport to cover alldetails or variations in hardware or software, nor to provide for every possible contingency inconnection with installation, operation, or maintenance. Features may be described hereinwhich are not present in all hardware and software systems. GE Fanuc Automation assumesno obligation of notice to holders of this document with respect to changes subsequently made.

    GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutorywith respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, orusefulness of the information contained herein. No warranties of merchantability or fitness forpurpose shall apply.

    Copyright 2003 GE Fanuc Automation North America, Inc.

    All Rights Reserved.

  • B-65292EN/03 SAFETY PRECAUTIONS

    s-1

    SAFETY PRECAUTIONSThis "Safety Precautions" section describes the precautions whichmust be observed to ensure safety when using FANUC AC SPINDLEMOTOR iB series.Users of any spindle motor model are requested to read this manualcarefully before using the spindle motor.The users are also requested to read this manual carefully andunderstand each function of the motor for correct use.The users are basically forbidden to do any behavior or action notmentioned in this manual. They are invited to ask FANUC previouslyabout what behavior or action is prohibited.

    Contents1.1 DEFINITION OF WARNING, CAUTION, AND NOTE.........s-21.2 WARNING ................................................................................s-31.3 CAUTION..................................................................................s-51.4 NOTE ...................................................................................s-6

  • SAFETY PRECAUTIONS B-65292EN/03

    s-2

    1.1 DEFINITION OF WARNING, CAUTION, AND NOTEThis manual includes safety precautions for protecting the user andpreventing damage to the machine. Precautions are classified intoWarning and Caution according to their bearing on safety. Also,supplementary information is described as a Note. Read the Warning,Caution, and Note thoroughly before attempting to use the machine.

    WARNINGApplied when there is a danger of the user beinginjured or when there is a damage of both the userbeing injured and the equipment being damaged ifthe approved procedure is not observed.

    CAUTIONApplied when there is a danger of the equipmentbeing damaged, if the approved procedure is notobserved.

    NOTEThe Note is used to indicate supplementaryinformation other than Warning and Caution.

    - Read this manual carefully, and store it in a safe place.

  • B-65292EN/03 SAFETY PRECAUTIONS

    s-3

    1.2 WARNING WARNING

    - Be safely dressed when handling a motor.Wear safety shoes or gloves when handling a motor as you may gethurt on any edge or protrusion on it or electric shocks.

    - Use a crane or lift to move a motor from one place to another.Motors are heavy. When moving them, use a crane or lift as required.(For the weight of motors, refer to Chapter 1 in Part I.)When moving a motor using a crane or lift, use a hanging bolt if themotor has a corresponding tapped hole, or textile rope if it has notapped hole. If a motor is attached with a machine or any other heavystuff, do not use a hanging bolt to move the motor as the hanging boltand/or motor may get broken.When moving a motor, be careful not to apply excessive force to itswindings as the windings may break and/or their insulation maydeteriorate.

    - Do not touch a motor with a wet hand.A failure to observe this caution is vary dangerous because you mayget electric shocks.

    - Before starting to connect a motor to electric wires, make sure they are isolatedfrom an electric power source.

    A failure to observe this caution is vary dangerous because you mayget electric shocks.

    - Do not bring any dangerous stuff near a motor.Motors are connected to a power line, and may get hot. If a flammableis placed near a motor, it may be ignited, catch fire, or explode.

    - Be sure to ground a motor frame.To avoid electric shocks, be sure to connect the grounding terminal inthe terminal box to the grounding terminal of the machine.

    - Do not ground a motor power wire terminal or short-circuit it to another powerwire terminal.

    A failure to observe this caution may cause electric shocks or aburned wiring.* Some motors require a special connection such as a winding

    changeover. Refer to their respective motor specificationmanuals for details.

    - Connect power wires securely so that they will not get loose.A failure to observe this caution may cause a wire to be disconnected,resulting in a ground fault, short circuit, or electric shock.

  • SAFETY PRECAUTIONS B-65292EN/03

    s-4

    WARNING - Do not supply the power to the motor while any terminal is exposed.

    A failure to observe this caution is very dangerous because you mayget electric shocks if your body or any conductive stuff touches anexposed terminal.

    - Do not get close to a rotary section of a motor when it is rotating.A rotating part may catch your cloths or fingers. Before starting amotor, ensure that there is no stuff that can fly away (such as a key)on the motor.

    - Before touching a motor, shut off the power to it.Even if a motor is not rotating, there may be a voltage across theterminals of the motor.Especially before touching a power supply connection, take sufficientprecautions.Otherwise you may get electric shocks.

    - Do not touch any terminal of a motor for a while (at least 5 minutes) after thepower to the motor is shut off.

    High voltage remains across power line terminals of a motor for awhile after the power to the motor is shut off. So, do not touch anyterminal or connect it to any other equipment. Otherwise, you may getelectric shocks or the motor and/or equipment may get damaged.

    - To drive a motor, use a specified amplifier and parameters.An incorrect combination of a motor, amplifier, and parameters maycause the motor to behave unexpectedly. This is dangerous, and themotor may get damaged.

    - Do not touch a motor when it is running or immediately after it stops.A motor may get hot when it is running. Do not touch the motorbefore it gets cool enough. Otherwise, you may get burned.

    - Ensure that motors and related components are mounted securely.If a motor or its component slips out of place or comes off when themotor is running, it is very dangerous.

    - When designing and assembling a machine tool, make it compliant withEN60204-1.

    To ensure the safety of the machine tool and satisfy Europeanstandards, when designing and assembling a machine tool, make itcompliant with EN60204-1. For details of the standards, refer to thestandards.

  • B-65292EN/03 SAFETY PRECAUTIONS

    s-5

    1.3 CAUTION CAUTION

    - FANUC motors are designed for use with machines. Do not use them for any otherpurpose.

    If a FANUC motor is used for an unintended purpose, it may cause anunexpected symptom or trouble. If you want to use a motor for anunintended purpose, previously consult with FANUC.

    - Ensure that a base or frame on which a motor is mounted is strong enough.Motors are heavy. If a base or frame on which a motor is mounted isnot strong enough, it is impossible to achieve the required precision.

    - Be sure to connect motor cables correctly.An incorrect connection of a cable cause abnormal heat generation,equipment malfunction, or failure. Always use a cable with anappropriate current carrying capacity (or thickness). For how toconnect cables to motors, refer to theirrespective specification manuals.

  • SAFETY PRECAUTIONS B-65292EN/03

    s-6

    1.4 NOTENOTE - Do not step or sit on a motor.

    If you step or sit on a motor, it may get deformed or broken. Do notput a motor on another unless they are in packages.

    - When storing a motor, put it in a dry (non-condensing) place at room temperature(0 to 40 C).

    If a motor is stored in a humid or hot place, its components may getdamaged or deteriorated. In addition, keep a motor in such a positionthat its shaft is held horizontal and its terminal box is at the top.

    - Do not remove a nameplate from a motor.If a nameplate comes off, be careful not to lose it. If the nameplate islost, the motor becomes unidentifiable, resulting in maintenancebecoming impossible. For a nameplate for a built-in spindle motor,keep the nameplate with the spindle.

    - Do not apply shocks to a motor or cause scratches to it.If a motor is subjected to shocks or is scratched, its components maybe adversely affected, resulting in normal operation being impaired.Be very careful when handling plastic portions, sensors, and windings,because they are very liable to break. Especially, avoid lifting a motorby pulling its plastic portion, winding, or power cable.

    - Do not conduct dielectric strength or insulation test for a sensor.Such a test can damage elements in the sensor.

    - When testing the winding or insulation resistance of a motor, satisfy theconditions stipulated in IEC34.

    Testing a motor under a condition severer than those specified inIEC34 may damage the motor.

    - Do not disassemble a motor.Disassembling a motor may cause a failure or trouble in it.If disassembly is in need because of maintenance or repair, pleasecontact a service representative of FANUC.

    - Do not modify a motor.Do not modify a motor unless directed by FANUC. Modifying amotor may cause a failure or trouble in it.

    - Use a motor under an appropriate environmental condition.Using a motor in an adverse environment may cause a failure ortrouble in it. Refer to their respective specification manuals for detailsof the operating and environmental conditions for motors.

  • B-65292EN/03 SAFETY PRECAUTIONS

    s-7

    NOTE - Do not apply a commercial power source voltage directly to a motor.

    Applying a commercial power source voltage directly to a motor mayresult in its windings being burned. Be sure to use a specifiedamplifier for supplying voltage to the motor.

    - For a motor with a terminal box, make a conduit hole for the terminal box in aspecified position.

    When making a conduit hole, be careful not to break or damageunspecified portions. Refer to an applicable specification manual.

    - Before using a motor, measure its winding and insulation resistances, and makesure they are normal.

    Especially for a motor that has been stored for a prolonged period oftime, conduct these checks. A motor may deteriorate depending on thecondition under which it is stored or the time during which it is stored.For the winding resistances of motors, refer to their respectivespecification manuals, or ask FANUC. For insulation resistances, seethe following table.

    - To use a motor as long as possible, perform periodic maintenance and inspectionfor it, and check its winding and insulation resistances.

    Note that extremely severe inspections (such as dielectric strengthtests) of a motor may damage its windings. For the windingresistances of motors, refer to their respective specification manuals,or ask FANUC. For insulation resistances, see the following table.

    MOTOR INSULATION RESISTANCE MEASUREMENTMeasure an insulation resistance between each winding andmotor frame using an insulation resistance meter (500 VDC).Judge the measurements according to the following table.

    Insulationresistance Judgment

    100 M or higher Acceptable

    10 to 100 MThe winding has begun deteriorating. There is noproblem with the performance at present. Besure to perform periodic inspection.

    1 to 10 MThe winding has considerably deteriorated.Special care is in need. Be sure to performperiodic inspection.

    Lower than 1 M Unacceptable. Replace the motor.

  • B-65292EN/03 INTRODUCTION

    p-1

    INTRODUCTIONThis manual includes information of following models.FANUC AC SPINDLE MOTOR iB seriesStandard type

    Single winding Double windings(Speed range switching control)50L/25000iB80M/15000iB80L/8000iB100S/12500iB112M/15000iB

    80S/20000iB112SS/20000iB112S/15000iB112L/15000iB112LL/15000iB132M/14000iB132L/14000iB160S/13000iB160M/13000iB160L/13000iB160LL/13000iB180M/6000iB180L/6000iB180LL/8000iB200M/6000iB200L/6000iB250M/3000iB

    High-speed type

    Single winding Double windings(Speed range switching control)40S/70000iB80S/40000iB

    100S/20000iB112S/20000iB112M/20000iB112L/20000iB112L/25000iB132L/25000iB160M/20000iB160L/20000iB160LL/20000iB

    CAUTIONThe motors cannot be driven normally if incorrecthandling or assembling is applied. ReadII.INSTRUCTION, especially 1.GENERAL, beforedesigning or assembling the spindle.

    NOTE1 The above models with some exceptions are certified

    by a certification organization (TV Rheinland).2 Many drawings in this manual are drawn by Third

    Angle Projection Method.3 Amplifier information is in the latest edition of

    Descriptions FANUC SERVO AMPLIFIER i series(B-65282EN). Refer to the manual to get informationabout the amplifier.

  • CONSTRUCTION B-65292EN/03

    p-2

    CONSTRUCTIONThis manual consists of following three parts.

    I. SPECIFICATIONSOutput characteristics, dimensions, cooling conditions, and so onare shown here.

    II. INSTRUCTIONInstallation instructions for the built-in motor are shown here.Refer to this part when you design or assemble a spindle.

    APPENDIXFormulas for acceleration time, specification number, rotorsleeve, switching unit and so on are shown here.

  • B-65292EN/03 HANDLING OF BUILT-IN MOTOR

    p-3

    HANDLING OF BUILT-IN MOTOR

    CAUTIONYou should read this clause before handling abuilt-in motor.If you handle the motor incorrectly, some trouble oraccident will occur. Refer to Part II.The word Motor described here means stator,rotor, sensor and all parts of the motor.

    Avoid impact or excessive force. It will damagemotor parts. Often it will not operate normally ifmotor parts are damaged.

    Do not machine on the parts without FANUCspermission. Machine only on the parts designatedby FANUC.

    Rotor may be deformed by incorrect method of machining.Refer to the Chapter II-3 for correct instructions.

    Protect the motor from water, oil, solvent and otherchemicals that may damage the motor insulation, andfrom conductive dust that may cause shorts in themotor.

    Do not heat or cool if it is unnecessary. Especially becareful to the heat shock.

    Some magnetic elements are used for a sensor and must bekept away from magnetic fields. A screw driverwhich had magnetic tip may damage the sensor.

    Place the stator sidewise as shown to store. Using a rubber pad ispreferable. Use jigs to protect the windings if you want to storethe stator vertically.

    JigRubber pad

  • B-65292EN/03 TABLE OF CONTENTS

    c-1

    TABLE OF CONTENTS

    SAFETY PRECAUTIONS ......................................................................... s-1INTRODUCTION ....................................................................................... p-1CONSTRUCTION...................................................................................... p-2HANDLING OF BUILT-IN MOTOR............................................................ p-3

    I. SPECIFICATIONS

    CONSTRUCTION OF THIS PART ................................................................31 SPECIFICATIONS..................................................................................5

    1.1 STANDARD TYPE.........................................................................................61.2 HIGH-SPEED TYPE ....................................................................................16

    2 POWER CURVES ................................................................................212.1 STANDARD TYPE.......................................................................................222.2 HIGH-SPEED TYPE ....................................................................................32

    3 DIMENSIONS.......................................................................................373.1 STATOR ......................................................................................................383.2 ROTOR........................................................................................................41

    3.2.1 Dimensions of Rotor.............................................................................................. 413.2.2 Reference Size of Spindle Shaft ............................................................................ 43

    3.3 BZi SENSOR ...............................................................................................443.3.1 With Mounting Ring.............................................................................................. 443.3.2 Without Mounting Ring......................................................................................... 453.3.3 Sensor Ring............................................................................................................ 46

    3.4 COOLING JACKET (REFERENCE) ............................................................473.5 REACTOR ...................................................................................................48

    II. INSTRUCTION

    CONSTRUCTION OF THIS PART ..............................................................531 GENERAL ............................................................................................55

    1.1 NOTES ........................................................................................................561.2 PROTECTION CLASS (WATER AND DUST PROOF) ...............................581.3 CLEARANCE AND CREEPAGE (DISTANCE FOR INSULATION) .............591.4 SATISFYING STANDARDS ........................................................................60

  • TABLE OF CONTENTS B-65292EN/03

    c-2

    1.5 DEVIATION .................................................................................................61

    2 STATOR...............................................................................................622.1 HEAT SHRINK FITTING..............................................................................632.2 CHECKING THE WINDING RESISTANCE.................................................642.3 POWER LEADS CONNECTION .................................................................652.4 GROUNDING A MOTOR.............................................................................682.5 CABLE CONNECTION (OUTLINE) .............................................................69

    3 ROTOR.................................................................................................703.1 MACHINING AND FINISHING.....................................................................713.2 ADJUSTING THE BALANCE.......................................................................733.3 HEAT SHRINK FITTING..............................................................................74

    4 BZi SENSOR .......................................................................................754.1 MOUNTING .................................................................................................764.2 INTERFERENCE.........................................................................................774.3 BZi SENSOR CONNECTION ......................................................................784.4 FEEDBACK SIGNAL ADJUSTMENT ..........................................................80

    5 LOAD METER (DYNAMOMETER) ......................................................825.1 STANDARD TYPE.......................................................................................835.2 HIGH SPEED TYPE ....................................................................................92

    APPENDIX

    CONSTRUCTION OF APPENDIX ...............................................................99A DEFINITION OF RATING...................................................................101B ACCELERATION TIME......................................................................102C COOLING CONDITION......................................................................103D ROTOR SLEEVE (REFERENCE) ......................................................104E CONTACTOR (SPEED RANGE SWITCHING UNIT) .........................107F SPECIFICATION NUMBER ...............................................................108G SELECTION DATA TABLE................................................................110

  • I. SPECIFICATIONS

  • B-65292EN/03 SPECIFICATIONS CONSTRUCTION OF THIS PART

    - 3 -

    CONSTRUCTION OF THIS PARTThis part includes followings.

    1 SPECIFICATIONS...................................................................... 5Technical data includes a cooling condition which is required toget rated output and to conform to the IEC standard.1.1 STANDARD TYPE............................................................. 61.2 HIGH-SPEED TYPE......................................................... 16

    2 POWER CURVES..................................................................... 21Power curves and torque curves of all models of standard typeand high-speed type.2.1 STANDARD TYPE........................................................... 222.2 HIGH-SPEED TYPE......................................................... 32

    3 DIMENSIONS........................................................................... 373.1 STATOR............................................................................ 383.2 ROTOR.............................................................................. 413.3 BZi SENSOR..................................................................... 443.4 COOLING JACKET (REFERENCE) ............................... 473.5 REACTOR......................................................................... 48

    NOTERefer to II.INSTRUCTION before installing a motorin a spindle. The part describes how to handle,assemble, and modify motors properly andcontains information required to satisfy IEC andother standards.

  • B-65292EN/03 SPECIFICATIONS 1.SPECIFICATIONS

    - 5 -

    1 SPECIFICATIONS

  • 1.SPECIFICATIONS SPECIFICATIONS B-65292EN/03

    - 6 -

    1.1 STANDARD TYPEModel name 50L/25000iB 80S/20000iB 80M/15000iB

    Type No.(A06B-) *8 1615-B120#Z318 1621-B120#Z312 1623-B170#Z011Item Low High

    S1 continuous 1.5 1.5 1.5 1.5(Max. current) (12) (10) (13) (11)S2 short time 2.2 2.2

    *1 Rated minutes 5min. 15min.Rated output (Max. current) kW (16) (14)

    S3 40% (A)(Max. current)

    S3 25% 3.7 3.7(Max. current) (23) (21)

    *2 Base 10000 4500 8000 3000Rated speed Power constant min-1 17000 10000 20000 12000

    Maximum 25000 15000 20000 15000Rated S1 continuous Nm 1.4 3.2 4.8

    Max. torque S2 or S3 3.5 7.0 7.0Power factor 0.74 0.69 0.68

    Rated voltage of motor input *3 VAC 144-183 122-191 144-217Winding connection Y

    Power leads connection *5 Connection B Connection E Connection ANumber of poles 4 4 4

    Resistance of winding *10 m 5% 303 754 251 436Insulation class F F F

    Temperature rise of winding K 105 105 105Required clearance mm 3 3 3

    Overheating temperature setting 5C 140 130 130IC code IC9U7A7 IC9U7A7 IC9U7A7Temperature C 20 20 20 20

    Temperature rise K 4 2 2 2Coolant Flowing rate Liter/min 12.0 12.0 12.9

    Specific heat J/gK 1.87 1.87 1.87Density g/cm3 0.78 0.78 0.78

    Pressure *11 kPa 2940 2940 2940Capacity of cooler *12 W 1200 1000 1160

    BZi sensor *4 T211 T201 T401Weight Stator kg 3 4 6

    Rotor 0.6 1.2 3Rotor inertia kgm2 0.0002 0.002 0.003

    Allowable overload *6 kW 4.4 2.6 4.4 2.6Spindle amplifier module (SPM-) 5.5i 5.5i 2.2iAC reactor (A81L-0001-) *13 - - -

    Date for choice of PSM *7 kW 1.5/4.6 1.5/4.8 1.5/2.7Parameter spec. (A06B-6111-) *9

    NOTE All specifications are guaranteed when using FANUCs amplifier and providing the cooling system required. All specification are guaranteed when input voltage of amplifier is 200/220/230VAC. (except for the

    112L/25000iB and 160LL/20000iB with the 400 V specification) IEC34 and VDE0110 etc. should be applied to conform to CE marking when installing the motor in a spindle.

    Refer to the standards for details. Use motors under following condition.

    Room temperature form 0 to 40C, 1000m or less above sea level, vibration acceleration of 1 G or less at no loador 10 G or less at cutting, dry environment, non-condensation.

  • B-65292EN/03 SPECIFICATIONS 1.SPECIFICATIONS

    - 7 -

    80L/8000iB 100L/12500iB 112SS/20000iB Model name1625-B170#Z011 1641-B120#Z011 1661-B120#Z312 Type No.(A06B-) *8

    Low High Item1.1 2.2 2.2 2.2 S1 continuous(20) (21) (28) (17) (Max. current)3.7 3.7 S2 short time

    30min. 30min. Rated minutes *1(28) (29) kW (Max. current) Rated output

    5.5 5.5 (A) S3 40%(31) (33) (Max. current)

    5.5 (S3 10%) S3 25%(53) (Max. current)

    1500 1500 1070 5000 Base *28000 8000 5000 20000 min-1 Power constant Rated speed8000 12500 5000 20000 Maximum7.0 14.0 20 Nm S1 continuous Rated

    23.6 23.6 49 S2 or S3 Max. torque0.74 0.75 0.66 Power factor

    114-217 105-218 99-176 VAC Rated voltage of motor input *3 Y Winding connection

    Connection A Connection B Connection E Power leads connection *54 4 4 Number of poles

    427 328 510 170 m 5% Resistance of winding *10F F F Insulation class

    105 105 105 K Temperature rise of winding3 3 3 mm Required clearance

    130 140 140 5C Overheating temperature settingIC9U7A7 IC9U7A7 IC9U7A7 IC code

    20 20 20 20 C Temperature5 3 4 4 K Temperature rise

    12.1 12.0 13.0 Liter/min Flowing rate Coolant1.87 1.87 1.87 J/gK Specific heat0.78 0.78 0.78 g/cm3 Density

    2940 2940 2940 kPa Pressure *111160 1160 4900 W Capacity of cooler *12T401 T401 T201 BZi sensor *4

    9 11 7 kg Stator Weight4 5 3 Rotor

    0.004 0.008 0.008 kgm2 Rotor inertia4.4 4.4 6.6 kW Allowable overload *65.5i 5.5i 11i Spindle amplifier module (SPM-)

    - - - AC reactor (A81L-0001-) *131.1/4.8 2.2/5.5 2.2/7.9 kW Date for choice of PSM *7

    Parameter spec. (A06B-6111-) *9

    *1 Data indicate the output of constant power range.*2 This speed is applied for S1 continuous rated. Refer to 2. POWER CURVES for details.*3 This is not an input voltage of amplifier. This indicates that the input voltage of motor is changed when the motor output changes

    within the rated output and speed.*4 A860-2120-Txxx. For velocity and position feedback. Install to a rotating axis. Refer to 3.3 SENSOR.*5 Refer to 2.3 POWER LEADS CONNECTION in the Part II.*6 Reference data, applied for 1 minute. This value is not guaranteed.*7 Reference data of Continuous/Maximum(at acceleration) output for the choice of PSM.*8 The number indicates the type number of the standard model. For other specification numbers such as of a model with a different

    sensor, refer to E. SPECIFICATION NUMBER in APPENDIX.*9 Refer to the manual, the latest edition of Parameter Manual (B-65280EN) for details.*10 The resistance of winding indicates reference data between the amplifier (SPM) and motor after motor power leads connection (the

    actual resistance differs slightly depending on the length of the used power cable). To measure the resistance of winding, refer to 2.2CHECKING THE WINDING RESISTANCE in II. INSTRUCTION before connection.

    *11 Adjust the coolant pressure according to the O-ring you use.*12 Actual calorie which must be removed from the motor is calculated as follows.

    Q(W)=Flowing rate(/min)Specific heat(J/gK)Density(g/cm3)Temperature rise(K)100060*13 The model for which this item is given requires an AC reactor between the motor and amplifier (SPM). Refer to 3.5 REACTOR.

  • 1.SPECIFICATIONS SPECIFICATIONS B-65292EN/03

    - 8 -

    Model name 112S/15000iB 112M/15000iBType No.(A06B-) *8 1671-B120#Z311 1673-B120#Z311

    Item Low HighS1 continuous 5.5 5.5 5.5(Max. current) (66) (40) (41)

    S2 SHORT TIME 7.5 7.5*1 Rated minutes 30min. 30min.

    Rated output (Max. current) kW (48) (51)S3 40% (A)

    (Max. current)S3 25% 7.5

    (Max. current) (85)*2 Base 1200 6000 1500

    Rated speed Power constant min-1 6000 15000 6000Maximum 6000 15000 15000

    Rated S1 continuous Nm 44 35Max. torque S2 or S3 60 48

    Power factor 0.63 71Rated voltage of motor input *3 VAC 79-194 132-189

    Winding connection Y Power leads connection *5 Connection E Connection B

    Number of poles 4 4Resistance of winding *10 m 5% 95 32 112

    Insulation class H FTemperature rise of winding K 125 105

    Required clearance mm 3 3Overheating temperature setting 5C 155 140

    IC code IC9U7A7 IC9U7A7Temperature C 20 20

    Temperature rise K 5 5 3Coolant Flowing rate Liter/min 13.2 12.9

    Specific heat J/gK 1.87 1.87Density g/cm3 0.78 0.78

    Pressure *11 kPa 2940 2940Capacity of cooler *12 W 5200 1160

    BZi sensor *4 T401 T401Weight Stator kg 10 25

    Rotor 5 8Rotor inertia kgm2 0.012 0.018

    Allowable overload *6 kW 9.0 9.0Spindle amplifier module (SPM-) 22i 11i

    AC reactor (A81L-0001-) *13 - -Date for choice of PSM *7 kW 5.5/9.9 5.5/12

    Parameter spec. (A06B-6111-) *9

    NOTE All specifications are guaranteed when using FANUCs amplifier and providing the cooling system required. All specification are guaranteed when input voltage of amplifier is 200/220/230VAC. (except for the

    112L/25000iB and 160LL/20000iB with the 400 V specification) IEC34 and VDE0110 etc. should be applied to conform to CE marking when installing the motor in a spindle.

    Refer to the standards for details. Use motors under following condition.

    Room temperature form 0 to 40C, 1000m or less above sea level, vibration acceleration of 1 G or less at no loador 10 G or less at cutting, dry environment, non-condensation.

  • B-65292EN/03 SPECIFICATIONS 1.SPECIFICATIONS

    - 9 -

    112L/15000iB 112LL/15000iB Model name1675-B100#Z311 1676-B100#Z311 Type No.(A06B-) *8

    Low High Low High Item15 18.5 15 18.5 S1 continuous

    (88) (107) (88) (117) (Max. current)18.5 22 18.5 22 S2 short time

    15min. 15min. 15min. 15min. Rated minutes *1(105) (123) (104) (132) kW (Max. current) Rated output

    (A) S3 40%(Max. current)

    18.5 18.5 S3 25%(139) (137) (Max. current)1500 5000 1200 3500 Base *23500 12500 2800 12000 min-1 Power constant Rated speed3500 15000 4500 15000 Maximum

    95 119 Nm S1 continuous Rated167 204 S2 or S3 Max. torque0.74 0.73 Power factor

    133-182 94-177 VAC Rated voltage of motor input *3Y Y Y Y Winding connection

    Connection D Connection D Power leads connection *54 4 Number of poles

    91 40 100 44 m 5% Resistance of winding *10H H Insulation class

    125 125 K Temperature rise of winding3 3 mm Required clearance

    180 180 5C Overheating temperature settingIC9U7A7 IC9U7A7 IC code

    20 20 20 20 C Temperature12 15 18 18 K Temperature rise

    12.0 12.9 Liter/min Flowing rate Coolant1.87 1.87 J/gK Specific heat0.78 0.78 g/cm3 Density

    2940 2940 kPa Pressure *114200 5200 W Capacity of cooler *12T401 T401 BZi sensor *4

    28 38 kg Stator Weight10 12 Rotor

    0.022 0.028 kgm2 Rotor inertia22.2 26.4 22.2 26.4 kW Allowable overload *6

    30i 30i Spindle amplifier module (SPM-)- - AC reactor (A81L-0001-) *13

    18.5/29.4 18.5/27.6 kW Date for choice of PSM *7Parameter spec. (A06B-6111-) *9

    *1 Data indicate the output of constant power range.*2 This speed is applied for S1 continuous rated. Refer to 2. POWER CURVES for details.*3 This is not an input voltage of amplifier. This indicates that the input voltage of motor is changed when the motor output changes

    within the rated output and speed.*4 A860-2120-Txxx. For velocity and position feedback. Install to a rotating axis. Refer to 3.3 SENSOR.*5 Refer to 2.3 POWER LEADS CONNECTION in the Part II.*6 Reference data, applied for 1 minute. This value is not guaranteed.*7 Reference data of Continuous/Maximum(at acceleration) output for the choice of PSM.*8 The number indicates the type number of the standard model. For other specification numbers such as of a model with a different

    sensor, refer to E. SPECIFICATION NUMBER in APPENDIX.*9 Refer to the manual, the latest edition of Parameter Manual (B-65280EN) for details.*10 The resistance of winding indicates reference data between the amplifier (SPM) and motor after motor power leads connection (the

    actual resistance differs slightly depending on the length of the used power cable). To measure the resistance of winding, refer to 2.2CHECKING THE WINDING RESISTANCE in II. INSTRUCTION before connection.

    *11 Adjust the coolant pressure according to the O-ring you use.*12 Actual calorie which must be removed from the motor is calculated as follows.

    Q(W)=Flowing rate(/min)Specific heat(J/gK)Density(g/cm3)Temperature rise(K)100060*13 The model for which this item is given requires an AC reactor between the motor and amplifier (SPM). Refer to 3.5 REACTOR.

  • 1.SPECIFICATIONS SPECIFICATIONS B-65292EN/03

    - 10 -

    Model name 132M/14000iB 132L/14000iBType No.(A06B-) *8 1713-B100#Z311 1705-B140#Z311

    Item Low High Low HighS1 continuous 15 18.5 15 22(Max. current) (81) (99) (100) (124)S2 short time 18.5 22 22, 18.5, 18.5 25

    *1 Rated minutes 15min. 10min. 5, 15, 30min. 30min.Rated output (Max. current) kW (97) (114) (141,121,115) (133)

    S3 40% (A)(Max. current)

    S3 25% 18.5(Max. current) (119)

    *2 Base 1400 5000 1000 5500Rated speed Power constant min-1 2500 14000 2000 14000

    Maximum 2500 14000 3000 14000Rated S1 continuous Nm 102 143

    Max. torque S2 or S3 161 233Power factor 81 74

    Rated voltage of motor input *3 VAC 135-185 133-195Winding connection Y Y Y

    Power leads connection *5 Connection D Connection HNumber of poles 4 4

    Resistance of winding *10 m 5% 69 29 114 19Insulation class F F

    Temperature rise of winding K 105 105Required clearance mm 3 3

    Overheating temperature setting 5C 155 155IC code IC9U7A7 IC9U7A7Temperature C 20 20 20 20

    Temperature rise K 7 19 7 17Coolant Flowing rate Liter/min 13.5 13.5

    Specific heat J/gK 1.87 1.87Density g/cm3 0.78 0.78

    Pressure *11 kPa 2940 2940Capacity of cooler *12 W 5200 5200

    BZi sensor *4 T401 T401Weight Stator kg 43 42

    Rotor 10 14Rotor inertia kgm2 0.028 0.039

    Allowable overload *6 kW 18 26.4 26.4 30Spindle amplifier module (SPM-) 30i 30iAC reactor (A81L-0001-) *13 - -

    Date for choice of PSM *7 kW 18.5/27.3 22/35Parameter spec. (A06B-6111-) *9

    NOTE All specifications are guaranteed when using FANUCs amplifier and providing the cooling system required. All specification are guaranteed when input voltage of amplifier is 200/220/230VAC. (except for the

    112L/25000iB and 160LL/20000iB with the 400 V specification) IEC34 and VDE0110 etc. should be applied to conform to CE marking when installing the motor in a spindle.

    Refer to the standards for details. Use motors under following condition.

    Room temperature form 0 to 40C, 1000m or less above sea level, vibration acceleration of 1 G or less at no loador 10 G or less at cutting, dry environment, non-condensation.

  • B-65292EN/03 SPECIFICATIONS 1.SPECIFICATIONS

    - 11 -

    160S/13000iB 160M/13000iB Model name1721-B120#Z311 1723-B120#Z311 Type No.(A06B-) *8

    Low High Low High Item11 11 5.5 11 S1 continuous

    (70) (73) (58) (79) (Max. current)15 15 S2 short time

    30min. 30min. Rated minutes *1(72) (91) kW (Max. current) Rated output15 18.5 (A) S3 40%

    (91) (112) (Max. current)7.5 (S3 15%) 18.5 S3 25%

    (100) (126) (Max. current)750 1400 300 850 Base *2

    1400 6000 850 3250 min-1 Power constant Rated speed1400 13000 850 13000 Maximum

    140 175 Nm S1 continuous Rated208 326 S2 or S3 Max. torque84 71 Power factor

    142-189 109-177 VAC Rated voltage of motor input *3Y Y Winding connection

    Connection E Connection E Power leads connection *54 4 Number of poles

    192 64 273 91 m 5% Resistance of winding *10F H Insulation class

    105 125 K Temperature rise of winding3 3 mm Required clearance

    140 155 5C Overheating temperature settingIC9U7A7 IC9U7A7 IC code

    20 20 20 C Temperature8 6 6 4 K Temperature rise

    14.5 14.5 Liter/min Flowing rate Coolant1.87 1.87 J/gK Specific heat0.78 0.78 g/cm3 Density

    2940 2940 kPa Pressure *115200 2900 W Capacity of cooler *12T401 T401 BZi sensor *4

    35 37 kg Stator Weight13 16 Rotor

    0.059 0.070 kgm2 Rotor inertia18 9.0 22.2 kW Allowable overload *622i 30i Spindle amplifier module (SPM-)- - AC reactor (A81L-0001-) *13

    11/17.9 11/28.6 kW Date for choice of PSM *7Parameter spec. (A06B-6111-) *9

    *1 Data indicate the output of constant power range.*2 This speed is applied for S1 continuous rated. Refer to 2. POWER CURVES for details.*3 This is not an input voltage of amplifier. This indicates that the input voltage of motor is changed when the motor output changes

    within the rated output and speed.*4 A860-2120-Txxx. For velocity and position feedback. Install to a rotating axis. Refer to 3.3 SENSOR.*5 Refer to 2.3 POWER LEADS CONNECTION in the Part II.*6 Reference data, applied for 1 minute. This value is not guaranteed.*7 Reference data of Continuous/Maximum(at acceleration) output for the choice of PSM.*8 The number indicates the type number of the standard model. For other specification numbers such as of a model with a different

    sensor, refer to E. SPECIFICATION NUMBER in APPENDIX.*9 Refer to the manual, the latest edition of Parameter Manual (B-65280EN) for details.*10 The resistance of winding indicates reference data between the amplifier (SPM) and motor after motor power leads connection (the

    actual resistance differs slightly depending on the length of the used power cable). To measure the resistance of winding, refer to 2.2CHECKING THE WINDING RESISTANCE in II. INSTRUCTION before connection.

    *11 Adjust the coolant pressure according to the O-ring you use.*12 Actual calorie which must be removed from the motor is calculated as follows.

    Q(W)=Flowing rate(/min)Specific heat(J/gK)Density(g/cm3)Temperature rise(K)100060*13 The model for which this item is given requires an AC reactor between the motor and amplifier (SPM). Refer to 3.5 REACTOR.

  • 1.SPECIFICATIONS SPECIFICATIONS B-65292EN/03

    - 12 -

    Model name 160L/13000iB 160LL/13000iBType No.(A06B-) *8 1725-B120#Z311 1726-B100#Z311

    Item Low High Low HighS1 continuous 7.5 7.5 15 25(Max. current) ( ) ( ) (84) (114)S2 short time 11 11 22 30

    *1 Rated minutes 30min. 30min. 10min. 30min.Rated output (Max. current) kW ( ) ( ) (114) (133)

    S3 40% (A)(Max. current)

    S3 25% 22(Max. current) (133)

    *2 Base 360 800 600 2500Rated speed Power constant min-1 800 10000 2000 10000

    Maximum 800 13000 3000 13000Rated S1 continuous Nm 199 238

    Max. torque S2 or S3 292 420Power factor 0.80

    Rated voltage of motor input *3 VAC 133-190Winding connection Y Y Y

    Power leads connection *5 Connection E Connection DNumber of poles 4 4

    Resistance of winding *10 m 5% 208 69 133 62Insulation class F H

    Temperature rise of winding K 105 125Required clearance mm 3 3

    Overheating temperature setting 5C 140 155IC code IC9U7A7 IC9U7A7Temperature C 20 20

    Temperature rise K 17 17Coolant Flowing rate Liter/min 10.1

    Specific heat J/gK 1.87Density g/cm3 0.78

    Pressure *11 kPa 2940Capacity of cooler *12 W 3740

    BZi sensor *4 T401 T401Weight Stator kg 52 65

    Rotor 23 28Rotor inertia kgm2 0.101 0.121

    Allowable overload *6 kW 13.2 26.4 36Spindle amplifier module (SPM-) 22i 30iAC reactor (A81L-0001-) *13 - -

    Date for choice of PSM *7 kW 7.5/16.4 25/39.4Parameter spec. (A06B-6111-) *9

    NOTE All specifications are guaranteed when using FANUCs amplifier and providing the cooling system required. All specification are guaranteed when input voltage of amplifier is 200/220/230VAC. (except for the

    112L/25000iB and 160LL/20000iB with the 400 V specification) IEC34 and VDE0110 etc. should be applied to conform to CE marking when installing the motor in a spindle.

    Refer to the standards for details. Use motors under following condition.

    Room temperature form 0 to 40C, 1000m or less above sea level, vibration acceleration of 1 G or less at no loador 10 G or less at cutting, dry environment, non-condensation.

  • B-65292EN/03 SPECIFICATIONS 1.SPECIFICATIONS

    - 13 -

    180M/6000iB 180L/6000iB Model name1743-B100#Z011 1745-B100#Z011 Type No.(A06B-) *8

    Low High Low High Item11 11 18.5 22 S1 continuous

    (52) (78) (83) (97) (Max. current)15 15 22 30 S2 short time

    20min. 30min. 30, 15min. 30min. Rated minutes *1(67) (99) (96, 129) (125) kW (Max. current) Rated output15 (A) S3 40%

    (74) (Max. current)15 S3 25%

    (93) (Max. current)450 800 500 1500 Base *2800 6000 800 2500 min-1 Power constant Rated speed800 6000 1500 6000 Maximum

    233 353 Nm S1 continuous Rated477 600 S2 or S3 Max. torque0.82 0.83 Power factor

    115-222 157-218 VAC Rated voltage of motor input *3Y Y Y Y Winding connection

    Connection D Connection D Power leads connection *54 4 Number of poles

    258 117 137 70 m 5% Resistance of winding *10F H Insulation class

    105 125 K Temperature rise of winding3 3 mm Required clearance

    140 155 5C Overheating temperature settingIC9U7A7 IC9U7A7 IC code

    20 20 20 20 C Temperature16 9 16 12 K Temperature rise

    13.8 9.7 Liter/min Flowing rate Coolant1.78 1.87 J/gK Specific heat0.87 0.78 g/cm3 Density

    2940 2940 kPa Pressure *114900 3740 W Capacity of cooler *12T401 T401 BZi sensor *4

    63 70 kg Stator Weight38 40 Rotor

    0.190 0.260 kgm2 Rotor inertia18 26.4 36 kW Allowable overload *630i 30i Spindle amplifier module (SPM-)- - AC reactor (A81L-0001-) *13

    11/25.6 22/34.8 kW Date for choice of PSM *7Parameter spec. (A06B-6111-) *9

    *1 Data indicate the output of constant power range.*2 This speed is applied for S1 continuous rated. Refer to 2. POWER CURVES for details.*3 This is not an input voltage of amplifier. This indicates that the input voltage of motor is changed when the motor output changes

    within the rated output and speed.*4 A860-2120-Txxx. For velocity and position feedback. Install to a rotating axis. Refer to 3.3 SENSOR.*5 Refer to 2.3 POWER LEADS CONNECTION in the Part II.*6 Reference data, applied for 1 minute. This value is not guaranteed.*7 Reference data of Continuous/Maximum(at acceleration) output for the choice of PSM.*8 The number indicates the type number of the standard model. For other specification numbers such as of a model with a different

    sensor, refer to E. SPECIFICATION NUMBER in APPENDIX.*9 Refer to the manual, the latest edition of Parameter Manual (B-65280EN) for details.*10 The resistance of winding indicates reference data between the amplifier (SPM) and motor after motor power leads connection (the

    actual resistance differs slightly depending on the length of the used power cable). To measure the resistance of winding, refer to 2.2CHECKING THE WINDING RESISTANCE in II. INSTRUCTION before connection.

    *11 Adjust the coolant pressure according to the O-ring you use.*12 Actual calorie which must be removed from the motor is calculated as follows.

    Q(W)=Flowing rate(/min)Specific heat(J/gK)Density(g/cm3)Temperature rise(K)100060*13 The model for which this item is given requires an AC reactor between the motor and amplifier (SPM). Refer to 3.5 REACTOR.

  • 1.SPECIFICATIONS SPECIFICATIONS B-65292EN/03

    - 14 -

    Model name 180LL/8000iB 200M/6000iBType No.(A06B-) *8 1746-B100#Z011 1753-B120#Z313

    Item Low High Low HighS1 continuous 18.5 22 15 15(Max. current) (112) (121) (96) (103)S2 short time 22 25 22 22

    *1 Rated minutes 30min. 30min. 30min. 30min.Rated output (Max. current) kW (131) (131) (116) (142)

    S3 40% (A)(Max. current)

    S3 25% 22(Max. current) (132)

    *2 Base 350 1300 485 900Rated speed Power constant min-1 1200 8000 900 3800

    Maximum 1500 8000 900 6000Rated S1 continuous Nm 504 295

    Max. torque S2 or S3 600 433Power factor 0.80 0.74

    Rated voltage of motor input *3 VAC 146-215 119-193Winding connection Y Y Y

    Power leads connection *5 Connection D Connection ENumber of poles 4 6

    Resistance of winding *10 m 5% 112 47 116 39Insulation class H H

    Temperature rise of winding K 125 125Required clearance mm 3 3

    Overheating temperature setting 5C 155 180IC code IC9U7A7 IC9U7A7Temperature C 20 20 20 20

    Temperature rise K 19 16 12 10Coolant Flowing rate Liter/min 12.0 12.0

    Specific heat J/gK 1.78 1.87Density g/cm3 0.87 0.78

    Pressure *11 kPa 2940 2940Capacity of cooler *12 W 4900 3740

    BZi sensor *4 T401 T611Weight Stator kg 102 56

    Rotor 48 25Rotor inertia kgm2 0.307 0.206

    Allowable overload *6 kW 26.4 30 26.4Spindle amplifier module (SPM-) 30i 30iAC reactor (A81L-0001-) *13 - -

    Date for choice of PSM *7 kW 22/35.1 15/29Parameter spec. (A06B-6111-) *9

    NOTE All specifications are guaranteed when using FANUCs amplifier and providing the cooling system required. All specification are guaranteed when input voltage of amplifier is 200/220/230VAC. (except for the

    112L/25000iB and 160LL/20000iB with the 400 V specification) IEC34 and VDE0110 etc. should be applied to conform to CE marking when installing the motor in a spindle.

    Refer to the standards for details. Use motors under following condition.

    Room temperature form 0 to 40C, 1000m or less above sea level, vibration acceleration of 1 G or less at no loador 10 G or less at cutting, dry environment, non-condensation.

  • B-65292EN/03 SPECIFICATIONS 1.SPECIFICATIONS

    - 15 -

    200L/6000iB 250M/3000iB Model name1755-B120#Z316 1773-B140#Z316 Type No.(A06B-) *8

    Low High Low High Item15 15 37 37 S1 continuous

    (131) (131) (197) (169) (Max. current)22 22 45 45 S2 short time

    30min. 30min. 30, 15min. 30min. Rated minutes *1(184) (183) (233, 267) (257) kW (Max. current) Rated output

    (A) S3 40%(Max. current)

    22 S3 25%(199) (Max. current)360 650 360 650 Base *2650 4500 650 2000 min-1 Power constant Rated speed650 6000 650 3000 Maximum

    398 981 Nm S1 continuous Rated700 1432 S2 or S3 Max. torque0.76 0.75 Power factor

    90-159 133-196 VAC Rated voltage of motor input *3Y Y Winding connection

    Connection E Connection F - Power leads connection *56 6 Number of poles

    74 25 53 18 m 5% Resistance of winding *10H H Insulation class

    125 125 K Temperature rise of winding3 3 mm Required clearance

    180 180 5C Overheating temperature settingIC9U7A7 IC9U7A7 IC code

    20 20 20 20 C Temperature16 8 19 12 K Temperature rise

    12.0 18.5 Liter/min Flowing rate Coolant1.87 1.87 J/gK Specific heat0.78 0.78 g/cm3 Density

    2940 2940 kPa Pressure *114900 8500 W Capacity of cooler *12T511 T511 BZi sensor *4

    74 140 kg Stator Weight31 75 Rotor

    0.258 0.920 kgm2 Rotor inertia26.4 60 kW Allowable overload *645i 55i Spindle amplifier module (SPM-)- - AC reactor (A81L-0001-) *13

    15/28.9 37/58.6 kW Date for choice of PSM *7Parameter spec. (A06B-6111-) *9

    *1 Data indicate the output of constant power range.*2 This speed is applied for S1 continuous rated. Refer to 2. POWER CURVES for details.*3 This is not an input voltage of amplifier. This indicates that the input voltage of motor is changed when the motor output changes

    within the rated output and speed.*4 A860-2120-Txxx. For velocity and position feedback. Install to a rotating axis. Refer to 3.3 SENSOR.*5 Refer to 2.3 POWER LEADS CONNECTION in the Part II.*6 Reference data, applied for 1 minute. This value is not guaranteed.*7 Reference data of Continuous/Maximum(at acceleration) output for the choice of PSM.*8 The number indicates the type number of the standard model. For other specification numbers such as of a model with a different

    sensor, refer to E. SPECIFICATION NUMBER in APPENDIX.*9 Refer to the manual, the latest edition of Parameter Manual (B-65280EN) for details.*10 The resistance of winding indicates reference data between the amplifier (SPM) and motor after motor power leads connection (the

    actual resistance differs slightly depending on the length of the used power cable). To measure the resistance of winding, refer to 2.2CHECKING THE WINDING RESISTANCE in II. INSTRUCTION before connection.

    *11 Adjust the coolant pressure according to the O-ring you use.*12 Actual calorie which must be removed from the motor is calculated as follows.

    Q(W)=Flowing rate(/min)Specific heat(J/gK)Density(g/cm3)Temperature rise(K)100060*13 The model for which this item is given requires an AC reactor between the motor and amplifier (SPM). Refer to 3.5 REACTOR.

  • 1.SPECIFICATIONS SPECIFICATIONS B-65292EN/03

    - 16 -

    1.2 HIGH-SPEED TYPEModel name 40S/70000iB 80S/40000iB 100S/20000iB

    Type No.(A06B-) *8 1601-B120#Z618 1631-B120#Y618 1641-B121#X617Item Low High

    S1 continuous 0.55 13 7.5 11(Max. current) ( ) (96) (49) (69)S2 short time 0.75 18.5 11 15

    *1 Rated minutes 15min. 1min. 10min. 30min.Rated output (Max. current) kW ( ) (127) (64) (83)

    S3 40% (A)(Max. current)

    S3 25%(Max. current)

    *2 Base 70000 30000 3300 7500Rated speed Power constant min-1 - 40000 5500 12000

    Maximum 70000 40000 5500 20000Rated S1 continuous Nm 0.075 4.1 22

    Max. torque S2 or S3 0.10 5.9 28Power factor 0.67

    Rated voltage of motor input *3 VAC 149-210Winding connection Y

    Power leads connection *5 Connection B Connection B Connection ENumber of poles 2 2 4

    Resistance of winding *10 m 5% 99 21 150 50Insulation class F F F

    Temperature rise of winding K 105 105 105Required clearance mm 3 3 3

    Overheating temperature setting 5C 140 140 140IC code IC9U7A7 IC9U7A7 IC9U7A7Temperature C 20 20 20 20

    Temperature rise K 3 11 5.6 5.6Coolant Flowing rate Liter/min 14.5 14.5 14.5

    Specific heat J/gK 1.78 1.78 1.87Density g/cm3 0.87 0.87 0.78

    Pressure *11 kPa 2940 2940 2940Capacity of cooler *12 W 1500 6000 2900

    BZi sensor *4 T211 T211 T411Weight Stator kg 3 15 11

    Rotor 0.3 2 4Rotor inertia kgm2 0.00008 0.004 0.007

    Allowable overload *6 kW 0.90 22.2 13.2 18Spindle amplifier module (SPM-) 2.2i 45i 22iAC reactor (A81L-0001-) *13 0142 0154 -

    Date for choice of PSM *7 kW 0.55/1 13/24.4 11/19.5Parameter spec. (A06B-6111-) *9

    NOTE All specifications are guaranteed when using FANUCs amplifier and providing the cooling system required. All specification are guaranteed when input voltage of amplifier is 200/220/230VAC. (except for the

    112L/25000iB and 160LL/20000iB with the 400 V specification) IEC34 and VDE0110 etc. should be applied to conform to CE marking when installing the motor in a spindle.

    Refer to the standards for details. Use motors under following condition.

    Room temperature form 0 to 40C, 1000m or less above sea level, vibration acceleration of 1 G or less at no loador 10 G or less at cutting, dry environment, non-condensation.

  • B-65292EN/03 SPECIFICATIONS 1.SPECIFICATIONS

    - 17 -

    112S/20000iB 112M/20000iB Model name1662-B120#Z317 1673-B100#Y617 Type No.(A06B-) *8

    Low High Low High Item7.5 11 10 15 S1 continuous(58) (70) (85) (89) (Max. current)

    15, 18.5 15 18.5 S2 short time30, 10min. 10min. 30min. Rated minutes *1(84,100) (115) (98) kW (Max. current) Rated output

    (A) S3 40%(Max. current)

    11 (25%, 15%) S3 25%(78,98) (Max. current)2300 6000 1500 10000 Base *26000 15000 6000 20000 min-1 Power constant Rated speed6000 20000 6000 20000 Maximum

    31 64 Nm S1 continuous Rated60 95 S2 or S3 Max. torque

    0.75 0.65 Power factor118-190 114-193 VAC Rated voltage of motor input *3

    Y Y Y Winding connectionConnection E Connection D Power leads connection *5

    4 4 Number of poles170 57 82 37 m 5% Resistance of winding *10

    F F Insulation class105 105 K Temperature rise of winding

    3 3 mm Required clearance140 140 5C Overheating temperature setting

    IC9U7A7 IC9U7A7 IC code20 20 20 20 C Temperature8 14 8 10 K Temperature rise

    12.0 12.0 Liter/min Flowing rate Coolant1.87 1.87 J/gK Specific heat0.78 0.78 g/cm3 Density

    2940 2940 kPa Pressure *114000 4000 W Capacity of cooler *12T411 T411 BZi sensor *4

    10 25 kg Stator Weight5 8 Rotor

    0.011 0.017 kgm2 Rotor inertia13.2 22.2 18 22.2 kW Allowable overload *6

    30i 30i Spindle amplifier module (SPM-)- - AC reactor (A81L-0001-) *13

    11/24.4 15/25.6 kW Date for choice of PSM *7Parameter spec. (A06B-6111-) *9

    *1 Data indicate the output of constant power range.*2 This speed is applied for S1 continuous rated. Refer to 2. POWER CURVES for details.*3 This is not an input voltage of amplifier. This indicates that the input voltage of motor is changed when the motor output changes

    within the rated output and speed.*4 A860-2120-Txxx. For velocity and position feedback. Install to a rotating axis. Refer to 3.3 SENSOR.*5 Refer to 2.3 POWER LEADS CONNECTION in the Part II.*6 Reference data, applied for 1 minute. This value is not guaranteed.*7 Reference data of Continuous/Maximum(at acceleration) output for the choice of PSM.*8 The number indicates the type number of the standard model. For other specification numbers such as of a model with a different

    sensor, refer to E. SPECIFICATION NUMBER in APPENDIX.*9 Refer to the manual, the latest edition of Parameter Manual (B-65280EN) for details.*10 The resistance of winding indicates reference data between the amplifier (SPM) and motor after motor power leads connection (the

    actual resistance differs slightly depending on the length of the used power cable). To measure the resistance of winding, refer to 2.2CHECKING THE WINDING RESISTANCE in II. INSTRUCTION before connection.

    *11 Adjust the coolant pressure according to the O-ring you use.*12 Actual calorie which must be removed from the motor is calculated as follows.

    Q(W)=Flowing rate(/min)Specific heat(J/gK)Density(g/cm3)Temperature rise(K)100060*13 The model for which this item is given requires an AC reactor between the motor and amplifier (SPM). Refer to 3.5 REACTOR.

  • 1.SPECIFICATIONS SPECIFICATIONS B-65292EN/03

    - 18 -

    Model name 112L/20000iB 112L/25000iBType No.(A06B-) *8 1675-B100#Y617 1675-B140#X627

    Item Low High Low HighS1 continuous 15 18.5 15 25(Max. current) (87) (103) ( ) ( )S2 short time 18.5 22 37

    *1 Rated minutes 15min. 15min. 15min.Rated output (Max. current) kW (101) (118) (111)

    S3 40% (A)(Max. current)

    S3 25% 18.5 25 (25%, 15%)(Max. current) (117) ( , )

    *2 Base 1800 8000 2000 8000Rated speed Power constant min-1 4000 20000 8000 15000

    Maximum 4000 20000 8000 25000Rated S1 continuous Nm 80 72

    Max. torque S2 or S3 118 159Power factor 0.67

    Rated voltage of motor input *3 VAC 161-191Winding connection Y Y Y Y

    Power leads connection *5 Connection D Connection GNumber of poles 4 4

    Resistance of winding *10 m 5% 91 40Insulation class H

    Temperature rise of winding K 125Required clearance mm 3

    Overheating temperature setting 5C 180IC code IC9U7A7 IC9U7A7Temperature C 20 20

    Temperature rise K 10 12Coolant Flowing rate Liter/min 12.0

    Specific heat J/gK 1.87Density g/cm3 0.78

    Pressure *11 kPa 2940Capacity of cooler *12 W 4000

    BZi sensor *4 T411 T411Weight Stator kg 28

    Rotor 9Rotor inertia kgm2 0.021

    Allowable overload *6 kW 22.2 26.4Spindle amplifier module (SPM-) 30i 45HViAC reactor (A81L-0001-) *13 - 0154

    Date for choice of PSM *7 kW 18.5/32.7Parameter spec. (A06B-6111-) *9

    NOTE All specifications are guaranteed when using FANUCs amplifier and providing the cooling system required. All specification are guaranteed when input voltage of amplifier is 200/220/230VAC. (except for the

    112L/25000iB and 160LL/20000iB with the 400 V specification) IEC34 and VDE0110 etc. should be applied to conform to CE marking when installing the motor in a spindle.

    Refer to the standards for details. Use motors under following condition.

    Room temperature form 0 to 40C, 1000m or less above sea level, vibration acceleration of 1 G or less at no loador 10 G or less at cutting, dry environment, non-condensation.

  • B-65292EN/03 SPECIFICATIONS 1.SPECIFICATIONS

    - 19 -

    132L/25000iB 160M/20000iB Model name1705-B140#Y617 1723-B140#Y627 Type No.(A06B-) *8

    Low High Low High Item15 18.5 11 18.5 S1 continuous

    (103) (92) (62) (105) (Max. current)18.5 22 15 22 S2 SHORT TIME

    30min. 15min. 15min. 30min. Rated minutes *1(118) (111) (73) (121) kW (Max. current) Rated output

    15 (A) S3 40%(87) (Max. current)15 S3 25%

    (108) (Max. current)1000 6000 850 4200 Base *22000 20000 3000 20000 min-1 Power constant Rated speed2000 25000 3000 20000 Maximum

    143 124 Nm S1 continuous Rated177 239 S2 or S3 Max. torque

    0.82 Power factor132-194 VAC Rated voltage of motor input *3

    Y Y Winding connectionConnection F - Connection F - Power leads connection *5

    4 4 Number of poles114 10 166 14 m 5% Resistance of winding *10

    H H Insulation class125 125 K Temperature rise of winding

    3 3 mm Required clearance155 180 5C Overheating temperature setting

    IC9U7A7 IC9U7A7 IC code20 20 20 20 C Temperature

    14 14 7 18 K Temperature rise13.5 13.5 Liter/min Flowing rate Coolant1.87 1.87 J/gK Specific heat0.78 0.78 g/cm3 Density

    2940 2940 kPa Pressure *115200 5800 W Capacity of cooler *12T411 T411 BZi sensor *4

    42 37 kg Stator Weight13 15 Rotor

    0.037 0.068 kgm2 Rotor inertia22.2 26.4 18 26.4 kW Allowable overload *6

    30i 30i Spindle amplifier module (SPM-)- - AC reactor (A81L-0001-) *13

    18.5/29 18.5/29 kW Date for choice of PSM *7Parameter spec. (A06B-6111-) *9

    *1 Data indicate the output of constant power range.*2 This speed is applied for S1 continuous rated. Refer to 2. POWER CURVES for details.*3 This is not an input voltage of amplifier. This indicates that the input voltage of motor is changed when the motor output changes

    within the rated output and speed.*4 A860-2120-Txxx. For velocity and position feedback. Install to a rotating axis. Refer to 3.3 SENSOR.*5 Refer to 2.3 POWER LEADS CONNECTION in the Part II.*6 Reference data, applied for 1 minute. This value is not guaranteed.*7 Reference data of Continuous/Maximum(at acceleration) output for the choice of PSM.*8 The number indicates the type number of the standard model. For other specification numbers such as of a model with a different

    sensor, refer to E. SPECIFICATION NUMBER in APPENDIX.*9 Refer to the manual, the latest edition of Parameter Manual (B-65280EN) for details.*10 The resistance of winding indicates reference data between the amplifier (SPM) and motor after motor power leads connection (the

    actual resistance differs slightly depending on the length of the used power cable). To measure the resistance of winding, refer to 2.2CHECKING THE WINDING RESISTANCE in II. INSTRUCTION before connection.

    *11 Adjust the coolant pressure according to the O-ring you use.*12 Actual calorie which must be removed from the motor is calculated as follows.

    Q(W)=Flowing rate(/min)Specific heat(J/gK)Density(g/cm3)Temperature rise(K)100060*13 The model for which this item is given requires an AC reactor between the motor and amplifier (SPM). Refer to 3.5 REACTOR.

  • 1.SPECIFICATIONS SPECIFICATIONS B-65292EN/03

    - 20 -

    Model name 160L/20000iB 160LL/20000iBType No.(A06B-) *8 1725-B140#Y617 1726-B140#Y617

    Item Low High Low HighS1 continuous 15 25 32 50(Max. current) (96) (115) ( ) ( )S2 short time 22 30 44 55

    *1 Rated minutes 10min. 30min. 10min. 10min.Rated output (Max. current) kW (123) (132) ( ) ( )

    S3 40% (A)(Max. current)

    S3 25% 44(Max. current) ( )

    *2 Base 750 2500 1600 12000Rated speed Power constant min-1 2000 6000 4000 20000

    Maximum 3000 20000 6000 20000Rated S1 continuous Nm 191 191

    Max. torque S2 or S3 263 350Power factor 0.81

    Rated voltage of motor input *3 VAC 136-190Winding connection Y Y Y

    Power leads connection *5 Connection G Connection F -Number of poles 4 4

    Resistance of winding *10 m 5% 112 28 124 10Insulation class F

    Temperature rise of winding K 105Required clearance mm 3

    Overheating temperature setting 5C 155IC code IC9U7A7 IC9U7A7Temperature C 20 20

    Temperature rise K 11 16Coolant Flowing rate Liter/min 12.0

    Specific heat J/gK 1.87Density g/cm3 0.78

    Pressure *11 kPa 2940Capacity of cooler *12 W 4500

    BZi sensor *4 T411 T411Weight Stator kg 52 65

    Rotor 22 27Rotor inertia kgm2 0.098 0.119

    Allowable overload *6 kW 26.4 36 52.8 66Spindle amplifier module (SPM-) 30i 75HViAC reactor (A81L-0001-) *13 - 0154

    Date for choice of PSM *7 kW 25/39.6 50/76.3Parameter spec. (A06B-6111-) *9

    NOTE All specifications are guaranteed when using FANUCs amplifier and providing the cooling system required. All specification are guaranteed when input voltage of amplifier is 200/220/230VAC. (except for the

    112L/25000iB and 160LL/20000iB with the 400 V specification) IEC34 and VDE0110 etc. should be applied to conform to CE marking when installing the motor in a spindle.

    Refer to the standards for details. Use motors under following condition.

    Room temperature form 0 to 40C, 1000m or less above sea level, vibration acceleration of 1 G or less at no loador 10 G or less at cutting, dry environment, non-condensation.

  • B-65292EN/03 SPECIFICATIONS 2.POWER CURVES

    - 21 -

    2 POWER CURVES

  • 2.POWER CURVES SPECIFICATIONS B-65292EN/03

    - 22 -

    2.1 STANDARD TYPE50L/25000iB (A06B-1615-B120#Z318)

    Motor speed(min-1)

    Out

    put(k

    W)

    2500000

    1

    4

    5

    10000 1700020000

    1.5kW S1 Cont.

    3.7kW S3 25%

    3

    2 2.1

    1.1

    25000

    Torq

    ue(N

    m)

    00

    1

    2

    5

    10000 17000Motor speed(min-1)

    2.0Nm

    0.8Nm

    1.4Nm S1 Cont.

    3.5Nm S3 25%

    3

    4

    0.80.4

    80S/20000iB (A06B-1621-B120#Z312)Low winding

    Out

    put(k

    W)

    00

    1

    2

    3

    5000 10000 15000Motor speed(min-1)

    3000

    0.75

    1.5kW S1 Cont.

    2.2kW S2 5min.

    1.5

    4500

    Torq

    ue(N

    m)

    00

    2.5

    5

    10

    5000 10000 15000Motor speed(min-1)

    30000.5

    3.2Nm S1 Cont.

    7.0Nm S2 5min.

    4500

    7.5

    2.1Nm

    1.4Nm 1.0

    High winding

    Out

    put(k

    W)

    00

    1.5

    3

    4.5

    5000 10000 20000Motor speed(min-1)

    8000

    15000

    1.5kW S1 Cont.

    3.7kW S3 25%

    Torq

    ue(N

    m)

    00

    2

    4

    6

    5000 10000 20000Motor speed(min-1)

    800015000

    1.8Nm S1 Cont.

    4.4Nm S3 25%

    0.7

    1.8

    80M/15000iB (A06B-1623-B170#Z011)

    00

    1

    2

    3

    5000 10000 15000Motor speed(min-1)

    Out

    put(k

    W)

    3000 12000

    1.5kW S1 Cont.

    2.2kW S2 15min.

    1.5

    1.1

    Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    2

    6

    8

    5000 150003000

    12000

    4.8Nm S1 Cont.

    7.0Nm S2 15min.

    41.8Nm

    1.2Nm1.00.7

  • B-65292EN/03 SPECIFICATIONS 2.POWER CURVES

    - 23 -

    80L/8000iB (A06B-1625-B170#Z011)

    0

    1

    2

    3

    1.1kW S1 Cont.

    3.7kW S2 30min.4

    5

    0 4000 8000Motor speed(min-1)

    Out

    put(k

    W)

    1500 8000Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    10

    20

    30

    40001500

    7.0Nm S1 Cont.

    24Nm S2 30min.

    4.41.3

    100S/12500iB (A06B-1641-B120#Z011)

    0

    1

    2

    3

    1500 8000

    2.2kW S1 Cont.

    3.7kW S2 30min.4

    5

    0 5000 10000 12500Motor speed(min-1)

    Out

    put(k

    W)

    2.2

    1.5

    12500Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    10

    20

    30

    50001500

    8000

    14Nm S1 Cont.

    24Nm S2 30min.

    1.71.1

    4.4Nm

    2.6Nm

    112SS/20000iB (A06B-1661-B120#Z312)Low winding

    Motor speed(min-1)

    Out

    put(k

    W)

    500000

    2

    4

    8

    25001070

    2.2kW S1 Cont.

    5.5kW S3 40%6S3 10%

    5000Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    20

    40

    60

    25001070

    20NmS1 Cont.

    49Nm S3 10%

    21Nm S3 40%

    11

    4.2

    20000Motor speed(min-1)

    Out

    put(k

    W)

    00

    2

    4

    8

    5000 1000018000

    2.2kW S1 Cont.

    5.5kW S3 40%6

    3.7

    20000Motor speed(min-1)

    00

    5

    10

    15

    5000 10000 18000

    4.2Nm S1 Cont.

    11Nm S3 40%

    Torq

    ue(N

    m)

    2.9Nm

    1.2Nm1.81.0

  • 2.POWER CURVES SPECIFICATIONS B-65292EN/03

    - 24 -

    112S/15000iB (A06B-1671-B120#Z311)Low winding

    00

    2.5

    7.5

    10

    2000 4000 6000Motor speed(min-1)

    1200

    5.5kW S1 Cont.

    7.5kW S3 25%

    5

    Out

    put(k

    W)

    Torq

    ue(N

    m)

    00

    20

    60

    80

    2000 4000 6000Motor speed(min-1)

    1200

    12

    44Nm S1 Cont.

    60Nm S3 25%

    40

    8.8

    High winding

    Out

    put(k

    W)

    00

    2.5

    7.5

    10

    5000 10000 15000Motor speed(min-1)

    6000

    5.5kW S1 Cont.

    7.5kW S2 30min.

    5

    Torq

    ue(N

    m)

    00

    5

    10

    15

    5000 10000 15000Motor speed(min-1)

    6000

    3.5

    8.8Nm S1 Cont.

    12Nm S2 30min.

    4.7

    112M/15000iB (A06B-1673-B120#Z311)

    Out

    put(k

    W)

    00

    2.5

    7.5

    10

    5000 10000 15000Motor speed(min-1)

    1500 6000

    5.5kWS1 Cont.

    7.5kW S2 30min.

    5

    2.21.5

    Torq

    ue(N

    m)

    00

    20

    40

    60

    10000 15000Motor speed(min-1)

    15006000

    35Nm S1 Cont.

    48Nm S2 30min.

    1.41.0

    12Nm

    8.8Nm

  • B-65292EN/03 SPECIFICATIONS 2.POWER CURVES

    - 25 -

    112L/15000iB (A06B-1675-B100#Z311)Low winding

    Out

    put(k

    W)

    00

    5

    20

    25

    1060 2000 3500Motor speed(min-1)

    1500

    15kW S1 Cont.

    18.5kW S2 15min.S3 25%

    10

    15

    Torq

    ue(N

    m)

    00

    50

    150

    200

    1060 2000 3500Motor speed(min-1)

    1500

    50

    95Nm S1 Cont.

    118Nm S2 15min.

    167Nm S3 25%

    100

    41

    High winding

    Out

    put(k

    W)

    00

    10

    20

    30

    5000 10000 15000Motor speed(min-1)

    18.5

    12500

    18.5kW S1 Cont.

    22kW S2 15min.

    15

    Torq

    ue(N

    m)

    00

    20

    40

    60

    5000 10000 15000Motor speed(min-1)

    12500

    35Nm S1 Cont.

    42Nm S2 15min.

    17Nm

    14Nm 9.512

    112LL/15000iB (A06B-1676-B100#Z311)Low winding

    Out

    put(k

    W)

    00

    5

    20

    25

    1500 3000 4500Motor speed(min-1)

    2800

    15

    15kWS1 Cont.

    18.5kW S2 15min.

    10

    15

    S3 25%

    865

    18.5

    1200

    Torq

    ue(N

    m)

    00

    100

    200

    300

    1500 3000 4500Motor speed(min-1)

    1200 2800

    119NmS1 Cont.

    147Nm S2 15min.

    865

    204Nm S3 25%

    63Nm51Nm

    2316

    High winding

    15000Motor speed(min-1)

    Out

    put(k

    W)

    00

    10

    20

    30

    5000 100003500 12000

    18.5kW S1 Cont.

    22kW S2 15min.

    18.5

    15

    15000Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    20

    60

    80

    50003500

    12000

    50Nm S1 Cont.

    60Nm S2 15min.

    40

    15Nm

    18Nm

    129.5

  • 2.POWER CURVES SPECIFICATIONS B-65292EN/03

    - 26 -

    132M/14000iB (A06B-1713-B100#Z311)Low winding

    Out

    put(k

    W)

    00

    5

    20

    25

    1100

    1400 2500Motor speed(min-1)

    S3 25%

    15kW S1 Cont.

    18.5kW S2 15min.

    10

    15

    2000

    Torq

    ue(N

    m)

    00

    50

    100

    200

    1400 2000 2500Motor speed(min-1)

    1100

    102Nm S1 Cont.

    126Nm S2 15min.

    161Nm S3 25%150

    7157

    High winding

    Out

    put(k

    W)

    00

    10

    20

    30

    5000 10000 14000Motor speed(min-1)

    18.5kW S1 Cont.

    22kW S2 10min.

    Torq

    ue(N

    m)

    00

    20

    40

    60

    5000 10000 14000Motor speed(min-1)

    35Nm S1 Cont.

    42Nm S2 10min.

    1513

    132L/14000iB (A06B-1705-B140#Z311)Low winding

    Out

    put(k

    W)

    00

    10

    20

    30

    1000 2000 3000Motor speed(min-1)

    900

    1315kWS1 Cont.

    22kW S2 5min.S215min.

    1517

    18.5kW S2 30min.

    Torq

    ue(N

    m)

    0 1000 2000 3000Motor speed(min-1)

    900

    105Nm143NmS1 Cont.

    233Nm S2 5min.

    196Nm S2 15min.177Nm S2 30min.

    0

    100

    200

    300

    88Nm72Nm

    544841

    High winding30

    14000Motor speed(min-1)

    Out

    put(k

    W)

    00

    10

    20

    5000 100005500

    22kW S1 Cont.25kW S2 30min.

    14000Motor speed(min-1)

    00

    20

    40

    60

    5500 10000

    38Nm S1 Cont.

    43Nm S2 30min.

    Torq

    ue(N

    m)

    1715

  • B-65292EN/03 SPECIFICATIONS 2.POWER CURVES

    - 27 -

    160S/13000iB (A06B-1721-B120#Z311)Low winding

    1400Motor speed(min-1)

    Out

    put(k

    W)

    00

    10

    15

    20

    500 1000688 910

    11kW S1 Cont.

    15kWS2 30min.

    750

    5

    S3 40%

    1400Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    50

    250

    500688

    910

    140Nm S1 Cont.

    208Nm S3 40%

    157Nm S2 30min.

    750

    200

    150

    100 102

    75

    High winding

    13000Motor speed(min-1)

    Out

    put(k

    W)

    00

    5

    15

    20

    5000 100001400 6000

    11kW S1 Cont.

    15kW S2 30min.

    10

    7.55.5

    13000Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    50

    100

    150

    6000 10000

    75Nm S1 Cont.

    102Nm S2 30min.

    3000

    24Nm

    18Nm 4.05.5

    160M/13000iB (A06B-1723-B120#Z311)Low winding

    850Motor speed(min-1)

    Out

    put(k

    W)

    00

    5

    7.5

    10

    300 600220

    5.5kW S1 Cont.

    7.5kW S3 15%

    2.5 100

    850Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    300

    400

    300 600220

    175Nm S1 Cont.

    326Nm S3 15%

    200

    8462

    High winding

    13000Motor speed(min-1)

    Out

    put(k

    W)

    00

    10

    20

    25

    3000850

    18.5kW S3 40%

    9753250

    6000

    7.5kW

    5.5kW

    15

    5

    11kWS1 Cont.

    S3 25%

    2.23.7

    13000Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    50

    150

    250

    10000850

    181Nm S3 40%

    208Nm S3 25%

    975 32503000 6000

    124Nm S1 Cont.

    200

    10059Nm

    32Nm

    12Nm

    8.8Nm

    1.62.7

  • 2.POWER CURVES SPECIFICATIONS B-65292EN/03

    - 28 -

    160L/13000iB (A06B-1725-B120#Z311)Low winding

    800Motor speed(min-1)

    Out

    put(k

    W)

    0 200 600360

    450

    7.5kW S1 Cont.

    11kW S2 30min.

    15

    0

    5

    10

    S3 40%

    800Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    100

    300

    400

    400360

    292Nm S3 40%

    233Nm S2 30min.

    199Nm S1 Cont.

    450

    200

    131

    90

    High winding

    13000Motor speed(min-1)

    Out

    put(k

    W)

    0

    5

    10

    15

    0 5000 10000800

    7.5kW S1 Cont.

    11kW S2 30min.

    5.5

    3.7

    13000Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    50

    100

    150

    5000 10000800

    90Nm S1 Cont.

    131Nm S2 30min.

    11Nm

    7.2Nm4.02.7

    160LL/13000iB (A06B-1726-B100#Z311)Low winding

    3000Motor speed(min-1)

    Out

    put(k

    W)

    00

    10

    20

    30

    2000500 1500

    15kW S1 Cont.

    22kW S2 10min.

    600

    S3 25%

    15

    11

    3000Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    100

    400

    500

    600 2000500

    1500

    238NmS1 Cont.

    420Nm S3 25%

    350Nm S2 10min.

    140Nm

    72Nm

    300

    200

    3548

    High winding

    13000Motor speed(min-1)

    Out

    put(k

    W)

    00

    10

    20

    40

    5000 100002500

    25kW S1 Cont.

    30kW S2 30min.30

    2218.5

    00

    50

    100

    150

    5000 100002500

    95Nm S1 Cont.

    115Nm S2 30min.

    29Nm

    24Nm

    13000Motor speed(min-1)

    Torq

    ue(N

    m)

    1614

  • B-65292EN/03 SPECIFICATIONS 2.POWER CURVES

    - 29 -

    180M/6000iB (A06B-1743-B100#Z011)Low winding

    800Motor speed(min-1)

    Out

    put(k

    W)

    00

    5

    15

    20

    400 600300 450

    11kW S1 Cont.

    15kW S2 20min.

    10

    200

    S3 25% S3 40%

    800Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    200

    400

    600

    400300 450

    233Nm S1 Cont.

    358Nm S3 40%

    318Nm S2 20min.

    477Nm S3 25%

    179131

    High winding

    6000Motor speed(min-1)

    Out

    put(k

    W)

    00

    5

    15

    20

    2000 4000800

    11kW S1 Cont.

    15kW S2 20min.

    10

    6000Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    100

    150

    200

    2000 4000800

    131Nm S1 Cont.

    179Nm S2 20min.

    50

    2418

    180L/6000iB (A06B-1745-B100#Z011)Low winding

    1500Motor speed(min-1)

    Out

    put(k

    W)

    00

    10

    20

    30

    500 1000350 800

    18.5kWS1 Cont.

    22kW S2 30min.

    S2 15min.

    18.5

    15

    1500Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    200

    600

    800

    500350

    800

    353NmS1 Cont.

    420Nm S2 30min.

    600Nm S2 15min.

    400 263Nm

    221Nm11895

    High winding

    0 2000 4000 6000Motor speed(min-1)

    Out

    put(k

    W)

    0

    10

    20

    40

    1500 2500

    22kW S1 Cont.

    30kW S2 30min.30

    18.515

    6000Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    100

    200

    250

    2500 40001500

    115Nm

    140NmS1 Cont.

    191Nm S2 30min.

    84Nm

    150

    502924

  • 2.POWER CURVES SPECIFICATIONS B-65292EN/03

    - 30 -

    180LL/8000iB (A06B-1746-B100#Z011)Low winding

    1500Motor speed(min-1)

    Out

    put(k

    W)

    00

    10

    20

    30

    500 1000350 1200

    18.5kW S1 Cont.

    22kW S2 30min.

    18.515

    1500Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    400

    600

    800

    500350

    1200

    505Nm S1 Cont.

    600Nm S2 30min.

    200

    175Nm

    147Nm11895

    High winding

    8000Motor speed(min-1)

    Out

    put(k

    W)

    00

    10

    20

    30

    4000 60001300

    22kW S1 Cont.25kW S2 30min.

    20000

    50

    150

    250

    200

    100

    8000Motor speed(min-1)

    Torq

    ue(N

    m)

    0 40001300

    30

    162Nm S1 Cont.

    184Nm S2 30min.

    26

    200M/6000iB (A06B-1753-B120#Z313)Low winding

    900Motor speed(min-1)

    Out

    put(k

    W)

    00

    10

    20

    30

    300485

    570

    15kW S1 Cont.

    22kWS2 30min.

    S3 25%

    00

    200

    400

    600

    300 570485

    233

    295Nm S1 Cont.

    433Nm S3 25%

    368Nm S2 30min.

    900Motor speed(min-1)

    Torq

    ue(N

    m)

    159

    High winding

    6000Motor speed(min-1)

    Out

    put(k

    W)

    00

    10

    20

    30

    2000900

    3800

    15kW S1 Cont.

    22kW S2 30min.

    11

    7.5

    6000Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    100

    200

    300

    2000 3800900

    55Nm

    159Nm S1 Cont.

    233Nm S2 30min.

    38Nm 1812

  • B-65292EN/03 SPECIFICATIONS 2.POWER CURVES

    - 31 -

    200L/6000iB (A06B-1755-B120#Z316)Low winding

    Out

    put(k

    W)

    00

    10

    20

    30

    250 360 650Motor speed(min-1)

    390500

    15kW S1 Cont.

    22kW S2 30min.

    300

    S3 25%

    Torq

    ue(N

    m)

    00

    200

    400

    800

    250 500 650Motor speed(min-1)

    300

    398Nm S1 Cont.

    700Nm S3 25%

    539Nm S2 30min.600

    390360

    323

    220

    High winding

    6000Motor speed(min-1)

    Out

    put(k

    W)

    00

    10

    20

    30

    2000 4000650 4500

    15kW S1 Cont.

    22kW S2 30min.

    15

    11

    6000Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    200

    300

    400

    2000 4500650

    32Nm

    220Nm S1 Cont.

    323Nm S2 30min.

    47Nm100

    1824

    250M/3000iB (A06B-1773-B140#Z316)Low winding

    650Motor speed(min-1)

    Out

    put(k

    W)

    00

    15

    45

    60

    250 500300

    360

    37kW S1 Cont.

    45kW S2 30min.

    30

    S2 15min.

    1200

    650Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    400

    1600

    500300

    360

    981Nm S1 Cont.

    1194Nm S2 30min.

    1432Nm S2 15min.

    800661544

    High winding

    3000Motor speed(min-1)

    Out

    put(k

    W)

    00

    15

    45

    60

    1000 2000650

    37kW S1 Cont.

    45kW S2 30min.

    30 3025

    200

    3000Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    600

    800

    1000 2000650

    543Nm S1 Cont.

    661Nm S2 30min.

    400215Nm

    177Nm9580

  • 2.POWER CURVES SPECIFICATIONS B-65292EN/03

    - 32 -

    2.2 HIGH-SPEED TYPE

    40S/70000iB (A06B-1601-B120#Z618)

    Motor speed(min-1)

    Out

    put(k

    W)

    00

    0.5

    1

    70000

    0.55

    0.75

    S1 Cont.

    S2 15min.

    70000Motor speed(min-1)

    00

    0.05

    0.1

    0.15

    0.075Nm S1 Cont.

    0.10Nm S2 15min.

    Torq

    ue(N

    m)

    80S/40000iB (A06B-1631-B120#Y618)

    Out

    put(k

    W)

    00

    5

    15

    25

    10000 20000 40000Motor speed(min-1)

    30000

    13kW S1 Cont.

    18.5kW S2 1min.

    10

    20

    Torq

    ue(N

    m)

    00

    2.5

    5

    7.5

    20000 30000 40000Motor speed(min-1)

    10000

    3.1

    4.1Nm S1 Cont.

    5.9Nm S2 1min.

    4.4

    100S/20000iB (A06B-1641-B121#X617)Low winding

    Out

    put(k

    W)

    00

    5

    10

    15

    2000 4000 5500Motor speed(min-1)

    33003800

    7.5kW S1 Cont.

    11kW S2 10min.

    Torq

    ue(N

    m)

    00

    10

    20

    40

    2000 4000 5500Motor speed(min-1)

    33003800

    22Nm S1 Cont.

    28Nm S2 10min.30

    13

    19

    High winding

    20000Motor speed(min-1)

    Out

    put(k

    W)

    00

    5

    15

    20

    100007500 12000

    11kW S1 Cont.

    15kW S2 30min.

    1011

    7.5

    20000Motor speed(min-1)

    Torq

    ue(N

    m)

    00

    25

    7500 12000

    12Nm14Nm S1 Cont.

    19Nm S2 30min.20

    15

    10

    58.8Nm

    5.33.6

  • B-65292EN/03 SPECIFICATIONS 2.POWER CURVES

    - 33 -

    112S/20000iB (A06B-1662-B120#Z317)Low winding

    Out

    put(k

    W)

    00

    5

    10

    15

    2300 4000 6000Motor speed(min-1)

    1750

    S3 15%

    7.5kW S1 Cont.

    11kW S3 25%

    Torq

    ue(N

    m)

    00

    25

    50

    75

    2300 4000 6000Motor speed(min-1)

    175012

    31Nm S1 Cont.

    60Nm S3 15%

    46Nm S3 25%

    18

    High winding

    20000Motor speed(min-1)

    Out

    put(k

    W)

    00

    5

    15

    25

    5000 100006000

    11kW S1 Cont.

    18.5kW S2 10min.

    15000

    15kW S2 30min.

    10

    20

    1315

    11

    Torq

    ue(N

    m)

    00

    10

    20

    40

    6000 15000 20000Motor speed(min-1)

    12Nm18Nm S1 Cont.

    24Nm S2 30min.

    29Nm S2 10min.30

    7.0Nm

    9.5Nm

    7.26.25.3

    112M/20000iB (A06B-1673-B100#Y617)Low winding

    Out

    put(k

    W)

    00

    5

    15

    20

    2000 4000 6000Motor speed(min-1)

    1500

    10kW S1 Cont.

    15kW S2 10min.

    10

    Out

    put(k

    W)

    00

    50

    100

    150

    2000 4000 6000Motor speed(min-1)

    150016

    64Nm S1 Cont.

    95Nm S2 10min.

    24

    High winding

    20000Motor speed(min-1)

    Out

    put(k

    W)

    00

    5

    20

    25

    10000

    15kW S1 Cont.

    18.5kW S2 30min.

    15

    10 Torq

    ue(N

    m)

    00

    10

    15

    25

    10000 20000Motor speed(min-1)

    14Nm S1 Cont.

    17Nm S2 30min.20

    5

    8.87.2

  • 2.POWER CURVES SPECIFICATIONS B-65292EN/03

    - 34 -

    112L/20000iB (A06B-1675-B100#Y617)Low winding

    Out

    put(k

    W)

    00

    5

    20

    25

    1000 2000 4000Motor speed(min-1)

    18003000

    15kW S1 Cont.

    18.5kW S2 15min.

    15

    10

    1500

    S3 25%

    Torq

    ue(N

    m)

    00

    50

    100

    150

    1000 2000 4000Motor speed(min-1)

    1500

    3000

    80Nm S1 Cont.

    98Nm S2 15min.

    118Nm S3 25%

    1800

    3644

    High winding

    Out

    put(k

    W)

    00

    10

    20

    30

    5000 10000 15000Motor speed(min-1)

    800020000

    18.5kW S1 Cont.

    22kW S2 15min.

    Torq

    ue(N

    m)

    00

    20

    40

    60

    5000 10000 20000Motor speed(min-1)

    800015000

    22Nm S1 Cont.

    42Nm S2 15min.

    118.8

    112L/25000iB (A06B-1675-B140#X627)Low winding

    Out

    put(k

    W)

    00

    10

    20

    30

    2000 4000 8000Motor speed(min-1)

    1500

    6000

    15kW S1 Cont.

    25kW S3 25%S3 15%

    Torq

    ue(N

    m)

    00

    50

    100

    200

    2000 6000 8000Motor speed(min-1)

    1500 18

    72Nm S1 Cont.

    119Nm S3 25%

    150

    4000

    159Nm S3 15%

    30

    High winding

    Out

    put(k

    W)

    00

    15

    30

    45

    10000 20000 25000Motor speed(min-1)

    8000 15000

    25kWS1 Cont.