EN 593 / MSS SP-67, Wafer Type, PN16 /...

45
Fivalco R -1- Dimensions (mm) Size 50 65 80 100 125 150 200 250 300 350 400 450 500 600 A 161 175 181 200 215 225 241 296 336 368 400 422 480 562 B 80 91 95 115 134 138 174 198 234 280 310 340 388 450 D 90 90 90 90 90 90 125 125 125 150 175 175 210 210 E 43 45 46 51.5 56 56.5 60 68.5 79.5 78 88 109 127 154 SxS 11x11 14x14 17x17 22x22 27x27 φ48 Notes: 1. Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange bolt circle dimensions comply with EN1092-2 PN10 / 16, ANSI B16.1 Class125. Other flange types are available. 3. Top flange conforms to ISO5211/1. *4. Valves size 2(50) to 12(300) can be rated at PN20 / Class150, but the body material should be ductile iron ASTM A536 Gr. 65-45-12. Working pressure is 20bar / 300psi. 5. Design & materials are subject to change without notice. Butterfly Valve EN 593 / MSS SP-67, Wafer Type, PN16 / Class125 Figure Number 2302E Stainless Steel Disc, EPDM Liner 2302N Stainless Steel Disc, NBR Liner 2303E Bronze Disc, EPDM Liner 2303N Bronze Disc, NBR Liner 2304E DI Disc, Chrome or Nickel Plated, EPDM Liner 2304N DI Disc, Chrome or Nickel Plated, NBR Liner Working Pressure and Temperature Nominal Pressure Size DN50-DN300: 16bar / 200psi Size DN350-DN600: 10bar / 150psi Working Temperature EPDM: -10to 120NBR: -10to 82Materials List Part Name Material EN Spec. ASTM Spec. Body* Cast Iron EN-JL1040 A126 Class B Shaft Stainless Steel BS970 416S21 AISI 416 Stainless Steel BS970 304S15 A351 CF8 Cast Bronze EN1982 CC491K B62 C83600 Disc Ductile Iron Chrome or Nickel Plated EN-JS1050 A536 65-45-12 Bushing PTFE Commercial Commercial Liner EPDM/NBR Commercial Commercial O-Ring EPDM/NBR Commercial Commercial Size 2-12Size 14-24

Transcript of EN 593 / MSS SP-67, Wafer Type, PN16 /...

Page 1: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-1-

Dimensions (mm)

Size 50 65 80 100 125 150 200 250 300 350 400 450 500 600

A 161 175 181 200 215 225 241 296 336 368 400 422 480 562 B 80 91 95 115 134 138 174 198 234 280 310 340 388 450 D 90 90 90 90 90 90 125 125 125 150 175 175 210 210 E 43 45 46 51.5 56 56.5 60 68.5 79.5 78 88 109 127 154

SxS 11x11 14x14 17x17 22x22 27x27 φ48

Notes: 1. Designed and tested in accordance with EN 593 or MSS SP-67.

2. Flange bolt circle dimensions comply with EN1092-2 PN10 / 16, ANSI B16.1 Class125. Other flange types are available.

3. Top flange conforms to ISO5211/1.

*4. Valves size 2”(50) to 12”(300) can be rated at PN20 / Class150, but the body material should be ductile iron ASTM A536 Gr. 65-45-12. Working pressure is 20bar / 300psi.

5. Design & materials are subject to change without notice.

Butterfly Valve EN 593 / MSS SP-67, Wafer Type, PN16 / Class125

Figure Number 2302E Stainless Steel Disc, EPDM Liner

2302N Stainless Steel Disc, NBR Liner

2303E Bronze Disc, EPDM Liner

2303N Bronze Disc, NBR Liner

2304E DI Disc, Chrome or Nickel Plated, EPDM Liner

2304N DI Disc, Chrome or Nickel Plated, NBR Liner

Working Pressure and Temperature

Nominal

Pressure

Size DN50-DN300: 16bar / 200psi

Size DN350-DN600: 10bar / 150psi

Working

Temperature

EPDM: -10℃ to 120℃

NBR: -10℃ to 82℃

Materials List Part Name Material EN Spec. ASTM Spec.

Body* Cast Iron EN-JL1040 A126 Class B

Shaft Stainless Steel BS970 416S21 AISI 416

Stainless Steel BS970 304S15 A351 CF8

Cast Bronze EN1982

CC491K B62 C83600 Disc

Ductile Iron Chrome or

Nickel Plated EN-JS1050 A536 65-45-12

Bushing PTFE Commercial Commercial

Liner EPDM/NBR Commercial Commercial

O-Ring EPDM/NBR Commercial Commercial

Size 2”-12”

Size 14”-24”

Page 2: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-2-

Dimensions (mm)

Size 50 65 80 100 125 150 200 250 300 350 400 450 500 600

A 140 152 160 180 191 202 241 274 315 368 400 422 480 562

B 68 76 85 100 120 132 160 200 230 280 310 340 388 450

D 90 90 90 90 90 90 125 125 125 150 175 175 210 210

E 43 45 46 51.5 56 56.5 60 68.5 79.5 78 88 109 127 154

SxS 11x11 14x14 17x17 22x22 27x27 φ48

Notes: 1. Designed and tested in accordance with EN 593 or MSS SP-67.

2. Flange bolt circle dimensions comply with EN1092-2 PN10 / 16, ANSI B16.1 Class125. Other flange types are available. 3. Top flange conforms to ISO5211/1. *4. Valves size 2” to 12” can be rated at PN20 / Class150, but the body material should be ductile iron ASTM

A536 Gr. 65-45-12. Working pressure is 20bar / 300psi. 5. Design & materials are subject to change without notice.

Size 2”-12”

Size 14”-24”

Figure Number 2502E Stainless Steel Disc, EPDM Liner

2502N Stainless Steel Disc, NBR Liner

2503E Bronze Disc, EPDM Liner

2503N Bronze Disc, NBR Liner

2504E DI Disc, Chrome or Nickel Plated, EPDM Liner

2504N DI Disc, Chrome or Nickel Plated, NBR Liner

Butterfly Valve EN 593 / MSS SP-67, Lug Type, PN16 / Class125

Working Pressure and Temperature Nominal

Pressure

Size DN50-DN300: 16bar / 200psi

Size DN350-DN600: 10bar / 150psi

Working

Temperature

EPDM: -10℃ to 120℃

NBR: -10℃ to 82℃

Materials List Part Name Material EN Spec. ASTM Spec.

Body* Cast Iron EN-JL1040 A126 Class B

Shaft Stainless Steel BS970 416S21 AISI 416

Stainless Steel BS970 304S15 A351 CF8

Cast Bronze EN1982

CC491K B62 C83600 Disc

Ductile Iron Chrome or

Nickel Plated EN-JS1050 A536 65-45-12

Bushing PTFE Commercial Commercial

Liner EPDM/NBR Commercial Commercial

O-Ring EPDM/NBR Commercial Commercial

Page 3: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-3-

Dimensions (mm)

Size 50 65 80 100 125 150 200 250 300

Pipe OD 60.3 73.0/76.1 88.9 114.3 139.7/141.3 165.1/168.3 219.1 273.0 323.9

A 122 140 147 177 204 215 245 295 320

B 77 85 90 108 120 145 180 230 260

C 30 30 30 30 30 30 30 30 30

D 90 90 90 90 90 90 125 125 125

E 84 97 97 116 148 148 133 159 165

Notes:

1. Designed and tested in accordance with EN 593 or MSS SP-67.

2. Grooves conform to European or AWWA C606 standard. Other groove dimensions are available.

3. Top flange conforms to ISO 5211/1.

4. Valve also can be made to shouldered end type.

5. Design & materials are subject to change without notice.

Figure Number 2902E Ductile Iron Disc, EPDM Encapsulated

2902N Ductile Iron Disc, NBR Encapsulated

Butterfly Valve EN 593 / MSS SP-67, Grooved End, PN20 / Class150

Working Pressure and Temperature Nominal

Pressure 20bar / 300psi

Working

Temperature

EPDM: -10℃ to 120℃

NBR: -10℃ to 82℃

Materials List

Part Name Material EN Spec. ASTM Spec.

Body Ductile Iron EN-JS1050 A536 65-45-12

Shaft Stainless Steel BS970 416S21 AISI 416 DI EPDM Coated EN-JS1050 A536 65-45-12

Disc DI NBR Coated EN-JS1050 A536 65-45-12

Bushing PTFE Commercial Commercial

O-Ring EPDM/NBR Commercial Commercial

Page 4: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-4-

Dimensions (mm)

Size 50 65 80 100 125 150 200

Pipe OD 60.3 73.0/76.1 88.9 114.3 139.7/141.3 165.1/168.3 219.1

A 81 97 97 116 148 148 135

B 151 210 210 245 292 335 398

C 46 70 70 89 102 113 140

D 155 155 205 245 245 310 310

E 103 124 145 178 216 240 343

Notes: 1.Grooves conform to European or AWWA C606 standard. Other groove dimensions are available.

2. Valve can be made to shouldered end type also.

3. Design and Materials are subject to change without notice.

Figure Number 2952E EPDM Lined Body

2952N NBR Lined Body

Butterfly Valve Steel Pipe Body, Grooved End, PN16 / Class150

Materials List Part Name Material EN Spec. ASTM Spec.

Steel Pipe, EPDM Coated BS970 050A20 AISI 1020

Body Steel Pipe,

NBR Coated BS970 050A20 AISI 1020

Shaft Stainless Steel BS970 416S21 AISI 416

Disc Stainless Steel BS970 304S15 A351 CF8

Coupling Ductile Iron EN-JS1050 A536 65-45-12

O-Ring EPDM/NBR Commercial Commercial

Spring Stainless Steel BS970 304S15 AISI 304

Gasket PTFE Commercial Commercial

Dust Cover Stainless Steel BS970 304S15 AISI 304

Handle Ductile Iron EN-JS1050 A536 65-45-12

Page 5: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-5-

Ductile Iron Lever Handle

Steel Lever Handle, FBE Coated

Gear Operator

Dimensions (mm) Valve Size Part Number T

DN50~ DN150 2000 - S 263

DN200~DN250 2000 - M 326

DN300 2000 - L 415

Dimensions (mm) Valve Size Part Number T

DN50~ DN150 2001 - S 260

DN200~DN250 2001 - M 325

DN300 2001 - L 400

Dimensions (mm) Valve Size 50~150 200~250 300~350 400~450 500~600

Part No. 2000-24 2000-30 2000-50 2000-80 2000-70

Ratio 24:1 30:1 50:1 80:1 70:1

L 160 238 226 266 241

H 65 85 95 121 118

D 195 297 297 388 388

E 108 153 161 252 264

C 130 177 198 281 303

Materials List Part Name Material EN Spec. ASTM Spec.

Housing Cast Iron EN-JL1040 A126 Class B

Cover Cast Iron EN-JL1040 A126 Class B

Worm Gear Carbon Steel BS970 060A47 AISI 1045

Segment Gear Ductile Iron EN-JS1050 A536 65-45-12

Handwheel Cast Iron EN-JL1040 A126 Class B

Butterfly Valve Lever Handle and Gear Operator

Page 6: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-6-

Design and Installation

Design requirements Fivalco butterfly valve should be connected to the piping system with approved couplings or flanges. Flow may be from either direction, and the valves may be positioned in any direction. Fivalco butterfly valves have been designed with a slow close handwheel operator, which effectively minimizes water hammer. These valves feature minimum flow restriction and pressure loss when in the fully open position. Installation When the valves are received from the manufacturer they should be handled carefully to avoid breakage and damage to the seating area. Before installation of the valves, clean piping, flange and coupling. When the valves close hard, it is usually due to debris lodged in the seating area. Often this may be corrected by backing off the handwheel and closing again. The valve should never be forced to seat by applying a wrench to the handwheel as this may distort the valve components or score the sealing surface. Care must be taken to align wafer valves correctly so that the disc operation to the fully open position will not be obstructed. The use of excessive force to open or close the valve violates all warranties whether express or implied. The inlet and outlet pipe adjacent to the valve should be properly supported to prevent excessive stress on the valve body. The valve should not be used to force a pipeline into position as this may result in distortion of the valve body. Care and Maintenance Fivalco butterfly valves require no regular maintenance, however, it is advisable to inspect and verify proper operation of the unit annually or in accordance with the requirements of the authority having jurisdiction. The inspection should include a visual check for leakage at the valve pipe connection and body to operator connection. Inspection and maintenance should be performed by a qualified inspection service. Switch Installation Fivalco butterfly valves are provided with internal supervisor position switches. The tamper switch operates by a cam connected to the valve stem. The switch will change position and close with two (2) full turns of the handwheel from the fully open position. Switch 1# For connection to the supervisory circuit Normally Open: 1 Yellow Normally Closed: 1 Red Common: 1 White Switch 2# Auxiliary switch connected per authority Normally Open: 1 Blue Normally Closed: 1 Orange Common: 1 Black Ground Lead: 1 Green

Dimensions (mm) Valve Size Part Number H D L K W

DN50~ DN150 S2000 - 40 100 120 115 145 110

DN200~DN300 S2000 - 50 115 170 162 200 165

Materials List Part Name Material EN Spec. ASTM Spec.

Housing Cast Iron EN-JL1040 A126 Class B

Cover Cast Iron EN-JL1040 A126 Class B

Worm Gear Carbon Steel BS970 060A47 AISI 1045

Segment Gear Ductile Iron EN-JS1050 A536 65-45-12

Handwheel Cast Iron EN-JL1040 A126 Class B

Butterfly Valve Gear Actuator with Tamper Switch

SWITCH WIRE OPTION

Page 7: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

Dimensions (mm)

Size 50 65 80 100 125 150 200 250 300 350 400 450 500 600

L 178 190 203 229 254 267 292 330 356 381 406 432 457 508

H(Open) 405 415 486 632 710 842 1100 1228 1373 1595 1900 2210 2600 3040

BS 190 190 190 305 305 305 305 405 405 508 558 610 610 762 C

ANSI 178 178 190 250 307 300 356 400 457 508 558 610 610 762

Notes 1. Designed to BS 5150 ( EN 1171), MSS SP-70.

2. Flanges machined and drilled to EN1092-2 PN16 / ANSI 125 or EN1092-2 PN25 / ANSI 250, other flange types are available.

3. Design & materials are subject to change without notice.

Gate Valve BS 5150 (EN 1171) & MSS SP-70, OS&Y Type

Figure Number and Pressure PN16 / Class125 PN25 / Class250

3113 Brass Stem, B16 C36000 3115 Brass Stem, B16 C36000

3114 Stainless Steel Stem SS420 3116 Stainless Steel Stem, SS420

Working Pressure:

DN50 to DN300: 16bar / 200psi

DN350 to DN600: 16bar / 150psi

Working Pressure:

DN50 to DN300: 25bar / 500psi

DN350 to DN600: 21bar / 300psi

Working Temperature: -10℃ to 120℃

Materials List

Part Name Material EN Spec. ASTM Spec.

PN16 / Class125 Cast Iron EN-JL1040 A126 Class B Body

PN25 / Class 250 Ductile Iron EN-JS1050 A536 65-45-12

Body Ring Bronze EN1982 CC491K B62 C83600

Wedge Ring Bronze EN1982 CC491K B62 C83600

PN16 / Class125 Cast Iron EN-JL1040 A126 Class B Wedge

PN25 / Class 250 Ductile Iron EN-JS1050 A536 65-45-12

Stem Nut Brass CuZn39Pb3 B16 C36000

Stem See above shown.

PN16 / Class125 Cast Iron EN-JL1040 A126 Class B Bonnet

PN25 / Class 250 Ductile Iron EN-JS1050 A536 65-45-12

Gasket Graphite Non-asbestos Non-asbestos

PN16 / Class125 Cast Iron EN-JL1040 A126 Class B Yoke

PN25 / Class 250 Ductile Iron EN-JS1050 A536 65-45-12

Packing Graphite Non-asbestos Non-asbestos

PN16 / Class125 Cast Iron EN-JL1040 A126 Class B Handwheel

PN25 / Class 250 Ductile Iron EN-JS1050 A536 65-45-12

-7-

Page 8: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

Dimensions (mm)

Size 50 65 80 100 125 150 200 250 300 350 400 450 500 600

L 178 190 203 229 254 267 292 330 356 381 406 432 457 508

H 327 322 340 420 477 542 668 750 835 1015 1120 1210 1250 1390

BS 190 190 190 305 305 305 305 405 405 508 558 610 610 762 D

ANSI 178 178 200 250 300 300 356 400 457 508 558 610 610 762

Notes 1. Designed to BS 5150 (EN 1171), MSS SP-70.

2. Flanges machined and drilled to EN1092-2 PN16 / ANSI 125 or EN1092-2 PN25 / ANSI 250, other flange types are available.

3. Design & materials are subject to change without notice.

Gate Valve BS 5150 (EN 1171) & MSS SP-70, NRS Type

Figure Number and Pressure PN16 / Class125 PN25 / Class250

3123 Brass Stem, B16 C36000 3125 Brass Stem, B16 C36000

3124 Stainless Steel Stem SS420 3126 Stainless Steel Stem, SS420

Working Pressure:

DN50 to DN300: 16bar / 200psi

DN350 to DN600: 16bar / 150psi

Working Pressure:

DN50 to DN300: 25bar / 500psi

DN350 to DN600: 21bar / 300psi

Working Temperature: -10℃ to 120℃

Materials List

Part Name Material EN Spec. ASTM Spec.

PN16 / Class125 Cast Iron EN-JL1040 A126 Class B Body

PN25 / Class 250 Ductile Iron EN-JS1050 A536 65-45-12

Body Ring Bronze EN1982 CC491K B62 C83600

Wedge Ring Bronze EN1982 CC491K B62 C83600

PN16 / Class125 Cast Iron EN-JL1040 A126 Class B Wedge

PN25 / Class 250 Ductile Iron EN-JS1050 A536 65-45-12

Stem Nut Brass CuZn39Pb3 B16 C36000

Stem See above shown.

PN16 / Class125 Cast Iron EN-JL1040 A126 Class B Bonnet

PN25 / Class 250 Ductile Iron EN-JS1050 A536 65-45-12

Gasket Graphite Non-asbestos Non-asbestos

Packing Graphite Non-asbestos Non-asbestos

PN16 / Class125 Cast Iron EN-JL1040 A126 Class B Handwheel

PN25 / Class 250 Ductile Iron EN-JS1050 A536 65-45-12

-8-

Page 9: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

Dimensions (mm)

Size 50 65 80 100 125 150 200 250 300 L 146 159 165 171 191 210 241 273 305 H 405 415 486 632 710 842 1100 1228 1373 D 191 191 191 305 305 305 305 406 547

Notes 1. Comply with BS 3464 and generally comply with BS 5150 (EN 1171).

2. Flanges machined and drilled to EN1092-2 PN16 or ANSI 125, other flange types are available.

3. Design & materials are subject to change without notice.

Gate Valve BS 3464 with All Iron Trim, OS&Y Type, PN16 / Class125

Figure Number 3119

Working Pressure and Temperature

Nominal Pressure 16bar / 200psi

Working Temperature -10℃ to 120℃

Materials List

Part Name Material EN Spec. ASTM Spec.

Body Cast Iron EN-JL1040 A126 Class B

Wedge Cast Iron EN-JL1040 A126 Class B

Stem Nut Brass CuZn39Pb3 B16 C36000

Stem Carbon Steel BS970 220M07

Bonnet Cast Iron EN-JL1040 A126 Class B

Gasket Graphite Non-asbestos Non-asbestos

Yoke Cast Iron EN-JL1040 A126 Class B

Packing Graphite Non-asbestos Non-asbestos

Handwheel Cast Iron EN-JL1040 A126 Class B

-9-

Page 10: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

Dimensions (mm)

Size 50 65 80 100 125 150 200 250 300 L 146 159 165 171 191 210 241 273 305 H 327 322 340 420 477 542 668 750 835 D 191 191 191 305 305 305 305 406 547

Notes 1. Comply with BS 3464 and generally comply with BS 5150 (EN 1171).

2. Flanges machined and drilled to EN1092-2 PN16 or ANSI 125, other flange types are available.

3. Design & materials are subject to change without notice.

Gate Valve BS 3464 with All Iron Trim, NRS Type, PN16 / Class125

Figure Number: 3129

Working Pressure and Temperature

Nominal Pressure 16bar / 200psi

Working Temperature -10℃ to 120℃

Materials List

Part Name Material EN Spec. ASTM Spec.

Body Cast Iron EN-JL1040 A126 Class B

Wedge Cast Iron EN-JL1040 A126 Class B

Stem Nut Brass CuZn39Pb3 B16 C36000

Stem Carbon Steel BS970 220M07

Bonnet Cast Iron EN-JL1040 A126 Class B

Gasket Graphite Non-asbestos Non-asbestos

Yoke Cast Iron EN-JL1040 A126 Class B

Packing Graphite Non-asbestos Non-asbestos

Handwheel Cast Iron EN-JL1040 A126 Class B

-10-

Page 11: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

Dimensions (mm)

Size 40 50 65 80 100 125 150 200 250 300 350 400

L 140 150 170 180 190 200 210 230 250 270 290 310

H 200 202 222 250 303 351 411 498 579 679 870 941

D 130 130 130 150 185 185 195 225 245 285 400 400

Notes 1. Comply with DIN 3352.

2. Face to face dimensions conform to DIN3202 F4 series.

3. Flanges machined and drilled to EN1092-2 PN10 / 16, other flange types are available.

4. Design & materials are subject to change without notice.

Figure Number 3125 Brass Stem

3126 Stainless Steel Stem, 17440X20Cr13

Working Pressure and Temperature

Size 40~150 200~300 350~400

Nominal Pressure 10 bar 6 bar 4 bar

Suitable Media -10℃ to 120℃

Materials List

Part Name Material EN Spec.

Body Cast Iron EN-JL1040

Disc Cast Iron EN-JL1040

Body Seat Ring Brass CuZn39Pb3

Disc Seat Ring Brass CuZn39Pb3

Stem Nut Brass CuZn39Pb3

Brass CuZn39Pb3 Stem

Stainless Steel 17440x20Cr13

Bonnet Cast Iron EN-JL1040

Packing Graphite Non-asbestos

O-Ring EPDM Commercial

Gland Cast Iron EN-JL1040

Gasket Graphite Non-asbestos

Handwheel Cast Iron EN-JL1040

Gate Valve DIN 3352, NRS Type

-11-

Page 12: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

Dimensions (mm)

Size 50 65 80 100 125 150 200 250 300

OD 60.3 73.0/76.1 88.9 114.3 139.7/141.3 165.1/168.3 219.1 273.0 323.9

L 178 190 203 229 254 267 292 330 356

H(Open) 405 415 486 632 710 842 1100 1228 1373

BS 190 190 190 305 305 305 305 405 405 C

ANSI 178 178 190 250 307 300 356 400 457

Notes 1. Designed to BS 5150 (EN 1171), MSS SP-70.

2. Grooved end dimensions conform to European or AWWA C606 standard. Other groove dimensions are available.

3. Design & materials are subject to change without notice.

Gate Valve BS 5150 (EN 1171) & MSS SP-70, OS&Y Type,

Figure Number 3913 Brass Stem, B16 C36000

3914 Stainless Steel Stem SS420

Working Pressure and Temperature

Nominal Pressure 16bar / 200psi

Working Temperature -10℃ to 120℃

Materials List

Part Name Material EN Spec. ASTM Spec.

Body Ductile Iron EN-JS1050 A536 65-45-12

Body Ring Bronze EN1982 CC491K B62 C83600

Wedge Ring Bronze EN1982 CC491K B62 C83600

Wedge Ductile Iron EN-JS1050 A536 65-45-12

Stem Nut Brass CuZn39Pb3 B16 C36000

Stem See above shown.

Bonnet Ductile Iron EN-JS1050 A536 65-45-12

Gasket Graphite Non-asbestos Non-asbestos

Yoke Ductile Iron EN-JS1050 A536 65-45-12

Packing Graphite Non-asbestos Non-asbestos

Handwheel Ductile Iron EN-JS1050 A536 65-45-12

-12-

Page 13: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

Dimensions (mm)

Size 50 65 80 100 125 150 200 250 300

OD 60.3 73.0/76.0 88.9 114.3 139.7/141.3 165.1/168.3 219.1 273.0 323.9

L 178 190 203 229 254 267 292 330 356

H 327 322 340 420 477 542 668 750 835

BS 190 190 190 305 305 305 305 405 405 C

ANSI 178 178 190 250 307 300 356 400 457

Notes 1. Designed to BS 5150 (EN 1171), MSS SP-70.

2. Grooved end dimensions conform European or AWWA C606 standard, other grooved dimensions are available.

3. Design & materials are subject to change without notice.

Figure Number 3923 Brass Stem, B16 C36000

3924 Stainless Steel Stem SS420

Working Pressure and Temperature

Nominal Pressure 16bar / 200psi

Working Temperature -10℃ to 120℃

Materials List

Part Name Material EN Spec. ASTM Spec.

Body Ductile Iron EN-JS1050 A536 65-45-12

Body Ring Bronze EN1982 CC491K B62 C83600

Wedge Ring Bronze EN1982 CC491K B62 C83600

Wedge Ductile Iron EN-JS1050 A536 65-45-12

Stem Nut Brass CuZn39Pb3 B16 C36000

Stem See above shown.

Bonnet Ductile Iron EN-JS1050 A536 65-45-12

Packing Graphite Non-asbestos Non-asbestos

Gasket Graphite Non-asbestos Non-asbestos

Handwheel Ductile Iron EN-JS1050 A536 65-45-12

Gate Valve BS 5150 (EN 1171) & MSS SP-70, NRS Type,

-13-

Page 14: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-1-

Dimensions (mm) Size DN50 DN65 DN80 DN100 DN125 DN150 DN200 DN250 DN300

L 203 216 241 292 330 356 495 622 698.5

H(Open) 295 336 345 389 425 511 580 720 859

H(Close) 275 307 317 355 390 455 508 640 733

D 190.5 190.5 190.5 305 305 305 305 400 457

Note: 1. Designed to EN 13789, MSS SP-85.

2. Flanges can be drilled to ANSI 125 or EN1092-2 PN16. Other flange drilling types are available.

3. Design & materials are subject to change without notice. *4. Valves can be rated at PN25 / Class250, but the body and bonnet material should be ductile iron ASTM A536 Gr. 65-45-12.

Flanges conform to EN1092-2 PN25 or ANSI B16.2 Class250. Working pressure at 25bar/500psi.

Globe Valve BS EN 13789 / MSS SP-85, PN16 / Class125

Figure Number 6122 Brass Stem

6123 Stainless Steel Stem

Materials List Part Name Materials EN Spec. ASTM Spec.

Body* Cast Iron EN-JL1040 A126 Class B

Bonnet* Cast Iron EN-JL1040 A126 Class B

Seat Ring Cast Bronze EN1982 CC491K B62 C83600

Disc Ring Cast Bronze EN1982 CC491K B62 C83600

Disc Cast Iron EN-JL1040 A126 Class B

Brass CuZn39Pb3 B16 C36000 Stem

Stainless Steel 17440x20Cr13 AISI 420

Packing Graphite Non-asbestos Non-asbestos

Gasket Graphite Non-asbestos Non-asbestos Yoke

Bushing Brass CuZn39Pb3 B16 C36000

Handwheel Cast Iron EN-JL1040 A126 Class B

-14-

Page 15: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-2-

Dimensions (mm) Size 15 20 25 32 40 50 65 80 100 125 150 200 250 300

L 130 150 160 180 200 230 290 310 350 400 480 600 730 850

D 95 105 115 140 150 165 180 200 220 250 285 340 405 460

H 155 160 180 220 230 250 260 340 377 422 485 568 645 760

C 100 100 100 120 140 140 200 200 240 280 320 360 400 400

Notes:

1. Face to face dimension in accordance with DIN 3202 Series F1.

2. End flanges conform to EN1092-2 PN16 or ANSI 125. Other flange types are available.

Figure Number 6125

Working Pressure and Temperature

Working Pressure 16bar

Working Temperature -10℃ to 120℃

Materials List Part Name Materials EN Spec. ASTM Spec.

Body Cast Iron EN-JL1040 A126 Class B

Bonnet Cast Iron EN-JL1040 A126 Class B

Stainless Steel BS970 304S15 AISI 304 Seat Ring

Cast Bronze EN1982 CC491K B62 C83600

Stainless Steel BS970 304S15 AISI 304 Disc Ring

Cast Bronze EN1982 CC491K B62 C83600

Disc Cast Iron EN-JL1040 A126 Class B

Stem Stainless Steel 17440x20Cr13 AISI 420

Packing Graphite Non-asbestos Non-asbestos

Gasket Graphite Non-asbestos Non-asbestos

Yoke

Bushing Brass CuZn39Pb3 B16 C36000

Handwheel Cast Iron EN-JL1040 A126 Class B

Globe Valve DIN 3356, PN16

-15-

Page 16: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-1-

Dimensions (mm)

Size 50 65 80 100 125 150 200

A 203 216 241 292 330 356 495

B 121 135 141 168 182 215 267

Size 250 300 350 400 450 500 600

A 622 699 787 914 914 1016 1219

B 305 343 450 520 550 590 680

Notes 1. Designed in accordance with EN 12334, BS 5153 or MSS SP-71.

2. Flanges conform to EN1092-2 PN10 / 16 or ANSI 125. Other flange types are available. 3. Design & materials are subject to change without notice.

*4. Valves can be rated at PN25 / Class250, but the body & bonnet material should be changed to ductile iron ASTM A536 Gr. 65-45-12.

Swing Check Valve EN 12334 / BS 5153 / MSS SP-71, PN16 / Class125

Figure Number 5101 Bronze Disc Ring

5102 EPDM Disc Ring

5103 NBR Disc Ring

Materials List Part Name Materials EN Spec. ASTM Spec.

Body* Cast Iron EN-JL1040 A126 Class B

Cover* Cast Iron EN-JL1040 A126 Class B

Side Plug Brass CuZn39Pb3 B16 C36000

Hanger Pin Brass CuZn39Pb3 B16 C36000

Hanger Ductile Iron EN-JS1050 A536 65-45-12

Disc Cast Iron EN-JL1040 A126 Class B

Cast Bronze EN1982

CC491K B62 C83600

Disc Ring

EPDM/NBR Commercial Commercial

Seat Ring Cast Bronze EN1982

CC491K B62 C83600

Gasket SS+Graphite Non-asbestos Non-asbestos

-16-

Page 17: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-2-

Dimensions (mm)

Size 50 65 80 100 125 150 200

A 203 216 241 292 330 356 495

B 121 135 141 168 182 215 267

Size 250 300 350 400 450 500 600

A 622 699 787 914 914 1016 1219

B 305 343 450 520 550 590 680

Notes 1. Designed in accordance with EN 12334, BS 5153 or MSS SP-71.

2. Flanges conform to EN1092-2 PN10 / 16 or ANSI 125. Other flange types are available.

3. Design & materials are subject to change without notice.

*4. Valves can be rated at PN25 / Class250, but the body & cover material should be changed to ductile iron ASTM A536 Gr. 65-45-12.

Figure Number 5108

Working Pressure and Temperature

Nominal Pressure 16bar / 200psi

Working Temperature -10℃ to 120℃

Materials List Part Name Materials EN Spec. ASTM Spec.

Body* Cast Iron EN-JL1040 A126 Class B

Cover* Cast Iron EN-JL1040 A126 Class B

Side Plug Brass CuZn39Pb3 B16 C36000

Hanger Pin Brass CuZn39Pb3 B16 C36000

Hanger Ductile Iron EN-JS1050 A536 65-45-12

Disc Cast Iron EN-JL1040 A126 Class B

Cast Bronze EN1982

CC491K B62 C83600

Disc Ring

EPDM/NBR Commercial Commercial

Seat Ring Cast Bronze EN1982

CC491K B62 C83600

Gasket SS+Graphite Non-asbestos Non-asbestos

Lever Carbon Steel BS970 050A20 AISI 1020

Weight Cast Iron EN-JL1040 A126 Class B

Spring Carbon Steel Spring Steel Spring Steel

Swing Check Valve with Lever & Weight (Spring)

EN 12334 / BS 5153 / MSS SP-71, PN16 / Class125

-17-

Page 18: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-3-

s List

Dimensions (mm)

Size 40 50 65 80 100 125 150 200 250 300

A 180 200 240 260 300 350 400 500 600 700

B 105 118 124 144 154 179 184 245 346 337

Notes 1. Face to face dimensions are according to DIN3202 F6 series.

2. Flange machined and drilled to EN1092-2 PN10 / 16, other flange types are available.

3. Design & materials are subject to change without notice.

*4. Valves can be rated at PN25, but the body & cover material should be changed to ductile iron EN-JS1050.

Figure Number 5201 Bronze Disc Ring

5202 EPDM Disc Ring

5203 NBR Disc Ring

Working Pressure and Temperature

Nominal Pressure 16bar

Working Temperature EPDM: -10℃ to 120℃

NBR: -10℃ to 82℃

Materials List

Part Name Materials EN Spec. ASTM Spec.

Body Cast Iron EN-JL1040 A126 Class B

Cover Cast Iron EN-JL1040 A126 Class B

Gasket Graphite Non-asbestos Non-asbestos

Hanger Pin Brass CuZn39Pb3 B16 C36000

Hanger Ductile Iron EN-JS1050 A536 65-45-12

Disc Cast Iron EN-JL1040 A126 Class B

Cast Bronze EN1982

CC491K B62 C83600

Disc Ring

EPDM/NBR Commercial Commercial

Seat Ring Cast Bronze EN1982

CC491K B62 C83600

Side Plug Brass CuZn39Pb3 B16 C36000

Swing Check Valve DIN, PN16

-18-

Page 19: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-4-

Dimensions (mm)

Size 50 65 80 100 125 150 200 250 300

OD 60.3 73.0/76.1 88.9 114.3 139.7/141.3 165.1/168.3 219.1 273.0 323.9

99 99 108 A

165 172 200 254 267 292 356 432 495

B 36 53 54 76 111 105 130 163 188

C 47 57 68 99 114 127 154 188 205

Notes 1. Grooves conform to European or AWWA C606 standard.

2. Other standard steel pipes and ductile iron pipes are available.

3. Design & materials are subject to change without notice.

Figure Number 5904E EPDM Coated Disc

5904N NBR Coated Disc

Working Pressure and Temperature

Nominal Pressure 25bar / 400psi

Working Temp. EPDM: -10ºC to 120ºC

NBR: -10ºC to 82ºC

Materials list

Part

Name Material EN Spec. ASTM Spec.

Body Ductile Iron EN-JS1050 A536 65-45-12

Disc DI EPEM/NBR

Coated EN-JS1050 A536 65-45-12

Seat Bronze EN1982

CC491K B62 C83600

Spring Stainless Steel BS970 304S15 AISI 304

Shaft Stainless Steel 17440x20Cr13 AISI 420

Gasket EPDM/NBR Commercial Commercial

Shaft

Plug Brass CuZn39Pb3 B16 C36000

Swing Check Valve Grooved End, PN25 / Class250

-19-

Page 20: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-5-

Dimensions (mm)

Size A1 A2 A3 B C D 50 98.4 105 109 44.5 33 29 65 111 124 129 48 47 30 80 130 136.5 144 51 52 56

100 162 174.6 164 57 76 75 125 194 197 194 63.5 95 95 150 216 222 220 70 121 114 200 273 279 275 73 164 156 250 336.6 340 340 79 194 187 300 384 409.6 410 86 241 222 350 448 451 446 108 267 229 400 498.5 514 515 108 317.5 248 450 562 549 550 108 355.6 298.5 500 619 606 610 140 387.4 324 600 727 717.6 737 152 482.6 387

Notes 1. A1 for flange BS 10 Table D/E, A2 for flange ANSI Class125, A3 for flange EN1092-2 PN16. 2. A* dimensions should be specified in order.

3. Design & materials are subject to change without notice.

Figure Number 5301E Stainless Steel Clapper, EPDM Seat Ring 5301N Stainless Steel Clapper, NBR Seat Ring 5302E Bronze Clapper, EPDM Seat Ring 5302N Bronze Clapper, NBR Seat Ring

Working Pressure and Temperature

Nominal Pressure 16 Bar / 200psi

Working Temp. EPDM: -10ºC to 120ºC

NBR: -10ºC to 82ºC

Materials list

Part Name Material EN Spec. ASTM Spec.

Body Cast Iron EN-JL1040 A126 Class B

Stainless Steel BS970 304S15 A351 CF8 Clapper

Cast Bronze EN1982 CC491K B62 C83600

Stainless Steel BS970 304S15 A351 CF8 Hinge Arm

Cast Bronze EN1982 CC491K B62 C83600

Seat EPDM/NBR Commercial Commercial

Hinge-Pin Stainless Steel 17440x20Cr13 AISI 420

Spacer PTFE Commercial Commercial

Spring Stainless Steel BS970 304S15 AISI 304

Swing Check Valve Wafer Type, PN16 / Class125

-20-

Page 21: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-6-

Dimensions (mm)

Size A1 A2 A3 B C

50 109 111 109 54 66

65 129 130 129 54 78

80 144 150 144 57 90

100 170 181 170 64 115

125 196 216 196 70 141

150 226 251 226 76 170

200 290 308 283 95 210

250 352 362 343 108 273

300 417 423 403 143 324

350 474 486 458 184 356

Notes 1. A1 for flange EN1092-2 PN40, A2 for flange ANSI B16.2 Class250, A3 for flange EN1092-2 PN25. 2. A* dimensions should be specified in order. 3. Design & materials are subject to change without notice.

Figure Number 5304 ASTM A351 CF8M / BS970 316S16 Body 5305 ASTM A351 CF8 / BS970 304S15 Body

Working Pressure and Temperature

Nominal Pressure 25bar / 40bar / 300psi / 600psi

Working Temp. -10ºC to 120ºC

Materials list

Part Name Material BS Spec. ASTM Spec.

970 304S15 A351 CF8 Body Stainless Steel

970 316S16 A351 CF8M

970 304S15 A351 CF8 Disc Stainless Steel

970 316S16 A351 CF8M

Seat Viton Commercial Commercial

Hinge Pin Stainless Steel 970 316S16 AISI 316

Stop Pin Stainless Steel 970 316S16 AISI 316

Pin Retainer Stainless Steel 970 304S15 AISI 304

Spring Stainless Steel 970 304S15 AISI 304

Washer PTFE Commercial Commercial

Gasket Viton Commercial Commercial

Double Door Check Valve Wafer Type, PN25 / PN40 / 300PSI

-21-

Page 22: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-7-

Dimensions (mm)

Size A1 A2 A3 B C 50 96 105 109 54 66 65 109 124 129 54 78 80 126 137 144 57 90 100 158 175 164 64 115 125 190 197 194 70 141 150 210 222 220 76 170 200 267 279 275 95 210 250 331 340 330 108 273 300 379 410 380 143 324 350 446 450 440 184 356 400 492.5 514 491 191 406 450 560 549 541 203 457 500 616 602 615 213 508 600 724 718 718 222 600

Notes 1. A1 for flange BS 10 Table D/E, A2 for flange ANSI B16.1 Class125, A3 for flange EN1092-2 PN16. 2. A* dimensions should be specified in order.

Figure Number 5306E Stainless Steel Disc, EPDM Seat 5306N Stainless Steel Disc, NBR Seat 5307E Bronze Disc, EPDM Seat 5307N Bronze Disc, NBR Seat

Working Pressure and Temperature

Nominal Pressure PN16: DN50 to DN600, 16bar Class125: DN50 to DN300, 200psi

DN350 and above, 150psi

Working Temp. EPDM: -10ºC to 120ºC

NBR: -10ºC to 82ºC

Materials list

Part Name Material EN Spec. ASTM Spec.

Body Cast Iron EN-JL1040 A126 Class B

Stainless Steel BS970 304S15 A351 CF8 Disc

Cast Bronze EN1982 CC491K B62 C83600 Seat EPDM/NBR Commercial Commercial

Hinge Pin Stainless Steel 17440x20Cr13 AISI 420

Stop Pin Stainless Steel 17440x20Cr13 AISI 420

Pin Retainer Stainless Steel BS970 304S15 AISI 304

Spring Stainless Steel BS970 304S15 AISI 304

Washer PTFE Commercial Commercial

Gasket EPDM/NBR Commercial Commercial

Double Door Check Valve Wafer Type, PN16 / Class125

-22-

Page 23: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-8-

Dimensions (mm/Inch)

Size 50/2” 65/2.5” 80/3” 100/4” 125/5” 150/6” 200/8” 250/10” 300/12” 350/14”

mm 108 127 146 178 213 248 305 359 415 478 A

Inch 4-1/4 5 5-3/4 7 8-3/8 9-3/4 12 14-1/8 16-5/16 18-13/16

mm 67 73 80 102 118 140 165 216 286 350 B

Inch 2-5/8 2-7/8 3-1/8 4 4-5/8 5-1/2 6-1/2 8-1/2 11-1/4 13-3/4

Notes 1. Flanges conform to EN1092-2 PN16 or ANSI B16.1 Class125.

2. Other flange types are available, specify in order.

*3. Body material should be ductile iron ASTM A536 Gr. 65-45-12 for PN25 / Class250 valves.

Figure Number 5312

Working Pressure and Temperature

Nominal Pressure PN16: DN50 to DN350, 16bar Class125: DN50 to DN300, 200psi

DN350 and above, 150psi

Working Temp. EPDM: -10ºC to 120ºC

NBR: -10ºC to 82ºC

Materials list

Part Name Material EN Spec. ASTM Spec.

Body* Cast Iron EN-JL1040 A126 Class B

Stainless Steel BS970 304S15 A351 CF8 Seat

Cast Bronze EN1982 CC491K B62 C83600

Stainless Steel BS970 304S15 A351 CF8 Disc

Cast Bronze EN1982 CC491K B62 C83600

Spring Stainless Steel BS970 304S15 AISI 304

Bushing Bronze EN1982 CC491K B62 C83600

Screw Stainless Steel BS970 304S15 AISI 304

Seat O-Ring EPDM/NBR Commercial Commercial

Silent Check Valve Wafer Type, PN16 / Class125

-23-

Page 24: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-9-

Materials list

No. Part Name Material EN Spec. ASTM Spec.

1 Housing Ductile Iron EN-JS1050 A536 65-45-12

2 Hex Bolt Carbon Steel Carbon Steel A307B

3 Washer Carbon Steel BS970 050A20 AISI 1020

4 O-Ring EPDM/NBR Commercial Commercial

5 Seat EPDM/NBR Commercial Commercial

6 Shaft Stainless Steel 17440x20Cr13 AISI 420

7 End Face Ductile Iron EN-JS1050 A536 65-45-12

8 Spring Stainless Steel BS970 304S15 AISI 304

Stainless Steel BS970 304S15 A351 CF8 9 Disc

Cast Bronze EN1982 CC491K B62 C83600

10 Eye Bolt Carbon Steel BS970 060A35 AISI 1035

Dimensions (mm)

Size 2-1/2 3 4 5 6 8 10 12

Pipe OD 73.0/76.1 88.9 114.3 139.7/141.3 165.1/168.3 219.1 273.0 323.9

L 140 150 197 211 211 232 260 305

D 178 191 235 254 280 372 406 457

Notes 1. Grooves conform to European or AWWA C606 standard.

2. Other standard steel pipes and ductile iron pipes are available.

3. Supplied with Eye Bolt above size DN100.

-24-

Figure Number 5905E Stainless Steel Disc, EPDM Seat

5905N Stainless Steel Disc, NBR Seat

5906E Bronze Disc, EPDM Seat

5906N Bronze Disc, NBR Seat

Working Pressure and Temperature

Nominal Pressure 20bar / 250psi

Working Temp. EPDM Seat: -10℃ to 120℃

NBR Seat: -10℃ to 82℃

Double Door Check Valve Grooved End, PN20 / 250PSI

Page 25: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-10-

Dimensions (mm/Inch)

Size 50/2" 65/2.5" 80/3" 100/4" 125/5" 150/6" 200/8" 250/10" 300/12" 350/14" 400/16"

mm 133 140 152 185 216 248 318 393 362 400 446 L

Inch 5-1/4 5-1/2 6 7-1/4 8-1/2 9-3/4 12-1/2 15-1/2 14-1/4 15-3/4 17-1/2

mm 152 178 191 229 254 279 343 406 483 533 597 D

Inch 6 7 7-1/2 9 10 11 13-1/2 16 19 21 23-1/2

Notes 1. Flanges conform to ANSI Class125 or EN1092-2 PN16.

2. Other flange types are available, specify in order.

3. Also available in sizes: 18", 20", 24" & 30".

*4. Valves can be rated at PN25 / Class250, but the body material should be changed to ductile iron ASTM A536 Gr. 65-45-12.

Figure Number 5104 Bronze Seat

5105 Stainless Steel

Working Pressure and Temperature

Nominal Pressure PN16: DN50 to DN400, 16bar Class125: DN50 to DN300, 200psi

DN350 and above, 150psi

Working Temp. EPDM: -10ºC to 120ºC

NBR: -10ºC to 82ºC

Materials list

Part Name Material EN Spec. ASTM Spec.

Body* Cast Iron EN-JL1040 A126 Class B

Stainless Steel BS970 304S15 A351 CF8 Disc

Cast Bronze EN1982 CC491K

B62 C83600

Stainless Steel BS970 304S15 A351 CF8 Seat

Cast Bronze EN1982 CC491K

B62 C83600

Seat O-Ring EPDM/NBR Commercial Commercial

Spring Stainless Steel BS970 304S15 AISI 304

Bushing Bronze EN1982 CC491K

B62 C83600

Screw Stainless Steel BS970 304S15 AISI 304

Silent Check Valve Flanged End, PN16 / Class125

-25-

Page 26: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-11-

Dimensions (mm)

Size 50 65 80 100 125 150 200 250 300

L 100 120 140 170 200 230 288 354 410

A 97 125 150 187 220 260 340 420 490

D 165 185 200 220 250 285 340 405 460

Notes

1. Designed and tested in accordance to EN12334.

2. Flange to EN1092-2 PN10 / PN16 or ANSI 125. Other flange type drillings available.

*3. Valves can be rated at PN25 / Class250, but the body & disc material should be changed to ductile iron ASTM A536 Gr. 65-45-12.

Figure Number

5106E EPDM Seat

5106N NBR Seat

Working Pressure and Temperature

Nominal Pressure 16bar / 200psi

Working Temp. EPDM: -10ºC to 120ºC

NBR: -10ºC to 82ºC

Materials list

Part Name Material EN Spec. ASTM Spec.

Body* Cast Iron EN-JL1040 A126 Class B

Disc* Cast Iron EN-JL1040 A126 Class B

Disc Ring EPDM/NBR Commercial Commercial

Spring Stainless Steel BS970 304S15 AISI 304

Bushing Bronze EN1982 CC491K B62 C83600

Stainless Steel 17440x20Cr13 AISI 420 Stem

Brass CuZn39Pb3 B16 C36000

Bracket Cast Iron EN-JL1040 A126 Class B

Screw Stainless Steel BS970 304S15 AISI 304

Silent Check Valve EN12334, Flanged End, PN16 / Class125

-26-

Page 27: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-12-

Dimensions (mm/Inch)

Size 2"

(50)

2-1/2"

(65)

3"

(80)

4"

(100)

5"

(125)

6"

(150)

8"

(200)

10"

(250)

12"

(300)

14"

(350)

16"

(400)

18"

(450)

20"

(500)

24"

(600)

A 8

(203)

8-1/2

(216)

9-9/16

(243)

11-1/2

(292)

13-3/4

(349)

15

(381)

19-1/2

(495)

24-1/2

(622)

27-1/2

(699)

31

(787)

32

(813)

36

(914)

40

(1016)

48

(1219)

B 3-3/4

(95)

3-3/4

(95)

4-1/3

(110)

4-3/4

(121)

5-13/16

(147)

5-13/16

(147)

8-3/4

(222)

10-1/4

(260)

11-1/2

(292)

13-1/8

(333)

15-3/8

(391)

17-1/8

(435)

19-1/8

(486)

22-3/4

(578)

Notes

1. Flanges conform to EN1092-2 PN16 or ANSI 125. Other flange types available.

2. External and internal Epoxy Powder coated.

Figure Number

5107N Carbon Steel, NBR Coated

5107E Carbon Steel, EPDM Coated

Working Pressure and Temperature

Nominal Pressure PN16: DN50 to DN600, 16bar Class125: DN50 to DN300, 200psi

DN350 and above, 150psi

Working Temp. EPDM: -10ºC to 120ºC

NBR: -10ºC to 82ºC

Materials list Part

Name Material EN Spec. ASTM Spec.

Cast Iron for DN50 to DN300

EN-JL1040 A126 Class B Body

Ductile Iron for DN350 and Above

EN-JS1050 A536 65-45-12

Cast Iron for DN50 to DN300

EN-JL1040 A126 Class B Cover

Ductile Iron for DN350 and Above

EN-JS1050 A536 65-45-12

Disc Ductile Iron

NBR/EPDM Coated EN-JS1050 A536 65-45-12

Gasket NBR/EPDM Commercial Commercial

Plug Malleable Iron Commercial Commercial

Flex Check Valve Flanged End, PN16 / Class125

-27-

Page 28: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-13-

Dimensions (mm)

Size 40 50 65 80 100 125 150 200 250 300 350

L 180 200 240 260 300 350 400 500 600 700 800

H 100 125 140 170 200 225 265 355 420 480 580

D 50 63 80 96 125 150 180 250 320 370 440

Notes

1. Face to face conforms to EN588-1, basic series 48 & DIN3202 F6. 2. Flanges conform to EN1092-2 PN10 / 16 or ANSI 125.

3. Prevention of return flow by means of ball check principle.

4. Functions even at a low pressure.

5. Free low passage, blockage-free.

6. Low frictional losses.

7. For sewage prone to blockages.

Ball Check Valve Flanged End, PN16 / Class125

Figure Number

5109

Working Pressure and Temperature

Nominal Pressure PN16: DN50 to DN350, 16bar Class125: DN50 to DN300, 200psi

DN350 and above, 150psi

Working Temp. EPDM: -10ºC to 120ºC

NBR: -10ºC to 82ºC

Materials list Part

Name Material EN Spec. ASTM Spec.

Body Ductile Iron EN-JS1050 A536 65-45-12

Cover Ductile Iron EN-JS1050 A536 65-45-12

Ball Aluminium

NBR/EPDM Coated

Gasket NBR/EPDM Commercial Commercial

-28-

Page 29: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

Balancing Valve NRS Type, PN16 / Class125

Figure Number 1209

Working Pressure and Temperature

Nominal Pressure 16bar / 200psi

Working Temperature -10℃ to 120℃

Materials List

Part Name Material EN Spec. ASTM Spec.

Body Ductile Iron EN-JS1050 A536 65-45-12

Disc DI+EPDM Coated EN-JS1050 A536 65-45-12

Disc Nut Brass CuZn39Pb3 B16 C36000

Stem Stainless Steel 17440x20Cr13 ANSI 420

O-Ring EPDM Commercial Commercial

Bonnet Ductile Iron EN-JS1050 A536 65-45-12

Gasket Graphite Commercial Commercial

Handwheel (DN50-DN100) Carbon Steel with FBE coated

Handwheel (DN125-DN200) Ductile Iron EN-JS1050 A536 65-45-12

Dimensions (mm)

Size 50 65 80 100 125 150 200

L 230 290 310 350 400 480 600

H 260 293 305 323 353 388 453

D 180 180 180 180 260 260 260

Notes 1. Flanged conform to EN1092-2 PN16 or ANSI 125. Other flange type drillings are available.

2. Face to face dimensions according to EN558-1 (basic series 1).

3. Design & material are subject to change without notice.

4. Attached the flow diagram DN50 to DN200.

-1- -29-

Page 30: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

Balancing Valve Flow Diagram

-2- -30-

Page 31: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

Balancing Valve Flow Diagram

-3- -31-

Page 32: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-1-

Standard Screens

Dimensions (mm)

Size 50 65 80 100 125 150 200 250 300 350 400 450 500 600

L 230 273 295 352 416 470 543 660 770 960 1079 1168 1275 1450

H 146 174 198 232 285 305 401 473 554 740 840 910 968 1160

Plug 1/2" 1" 1" 1" 1-1/4" 1-1/2" 1-1/2" 2" 2" 2" 2" 2" 2" 2" Notes 1. Flanges conform to EN1092-2 PN16 / ANSI 125 or EN1092-2 PN25 / ANSI 250.

2. Other flange types are available.

3. Design, dimensions and materials are subject to change without notice.

Size Hole Dia. Free Flow Area

DN50 to 80 1.5mm 33%

DN100 to 600 3.0mm 40%

Y-Strainer PN16 / PN25 / Class125 / Class250

Figure Number 7101 Working Pressure at 16 bar or Class 125

7102 Working Pressure at 25 bar or Class 250

Working Pressure and Temperature

PN16 / Class 125 PN25 / Class 250

DN50 to DN300:

16 bar / 200psi

DN350 to DN600:

16 bar / 150 psi

DN50 to DN300:

25 bar / 500 psi

DN350 to DN600:

21 bar / 300 psi

Working Temperature: -10℃ to 120℃

Materials List

Part Name Material EN Spec. ASTM Spec.

7101 Cast Iron EN-JL1040 A126 Class B Body

7102 Ductile Iron EN-JS1050 A536 65-45-12

7101 Cast Iron EN-JL1040 A126 Class B Cover

7102 Ductile Iron EN-JS1050 A536 65-45-12

Screen Stainless Steel SS304 SS304

Gasket Teflon / Graphite Commercial Commercial

7101 Cast Iron EN-JL1040 A126 Class B Plug

7102 Ductile Iron EN-JS1050 A536 65-45-12

-32-

Page 33: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-2-

Standard Screens

Dimensions (mm)

Size 50 65 80 100 125 150 200 250 300 350 400 450 500 600

L 230 290 310 350 400 480 600 730 850 980 1100 1200 1250 1450

H 135 165 186 226 267 305 358 495 530 740 840 910 968 1160

Plug 1/2" 1" 1" 1" 1-1/4" 1-1/2" 1-1/2" 2" 2" 2" 2" 2" 2" 2" Notes 1. Flange to EN1092-2 PN16 / PN25. Other flange types are available.

2. Face to face dimensions are conform to DIN3202 F1 series.

3. Design, dimensions and materials are subject to change without notice.

Size Hole Dia. Free Flow Area

DN50 to 80 1.5mm 33%

DN100 to 600 3.0mm 40%

Figure Number: 7103 Working Pressure at 16 bar

7107 Working Pressure at 25 bar

Working Pressure and Temperature

PN16 PN25

DN50 to DN600: 16 bar DN50 to DN300: 25 bar

DN350 to DN600: 21 bar

Working Temperature: -10℃ to 120℃

Materials List

Part Name Material EN Spec. ASTM Spec.

7103 Cast Iron EN-JL1040 A126 Class B Body

7107 Ductile Iron EN-JS1050 A536 65-45-12

7103 Cast Iron EN-JL1040 A126 Class B Cover

7107 Ductile Iron EN-JS1050 A536 65-45-12

Screen Stainless Steel SS304 SS304

Gasket Teflon / Graphite Commercial Commercial

7103 Cast Iron EN-JL1040 A126 Class B Plug

7107 Ductile Iron EN-JS1050 A536 65-45-12

Y-Strainer DIN PN16 / PN25

-33-

Page 34: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-3-

Standard Screens

Dimensions (mm)

Size 50 65 80 100 125 150 200 250 300

OD 60.3 73.0/76.1 88.9 114.3 139.7/141.3 165.1/168.3 219.1 273.0 323.9

L 225 285 318 375 448 502 640 710 780

H 152 215 219 254 322 365 462 540 610

Plug 1/2” 1” 1” 1-1/2” 2” 2” 2” 2” 2”

Notes 1. Grooved end dimensions conform to European or AWWA C606 standard, other grooved dimensions are available

2. Design, dimensions and materials are subject to change without notice.

Size Hole Dia. Free Flow Area

DN50 to 80 1.5mm 33%

DN100 to DN300 3.0mm 40%

Figure Number: 7901

Working Pressure and Temperature

Nominal Pressure 20bar / 300psi

Working Temperature -10℃ to 120℃

Materials List

Part Name Material EN Spec. ASTM Spec.

Body Ductile Iron EN-JS1050 A536 65-45-12

Cover Ductile Iron EN-JS1050 A536 65-45-12

Screen Stainless Steel SS304 SS304

Gasket Teflon / Graphite Commercial Commercial

Plug Ductile Iron EN-JS1050 A536 65-45-12

Y-Strainer Grooved End Type, PN20 / Class150

-34-

Page 35: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-4-

Dimensions (mm)

Size 15 20 25 32 40 50 65 80

A 85 98 116 135 154 190.5 223 254

B 62 72 87 100 115 145 184 189

Hole Dia. 0.8 0.8 0.8 0.8 0.8 0.8 1.1 1.1

Plug 3/8” 1/2” 1/2” 3/4” 3/4” 1” 1” 1-1/4”

Notes 1. NPT Thread and Metric thread are all available.

2. Shell test pressure is 37.5bar / 750psi.

3. Design, dimensions and materials are subject to change without notice.

Figure Number: 7701

Working Pressure and Temperature

Nominal Pressure 25bar / 500psi

Working Temperature -10℃ to 120℃

Materials List

Part Name Material EN Spec. ASTM Spec.

Body Cast Iron EN-JL1040 A126 class B

Cover Cast Iron EN-JL1040 A126 class B

Screen Stainless Steel SS304 SS304

Gasket Teflon / Graphite Commercial Commercial

Plug Cast Iron EN-JL1040 A126 class B

Y-Strainer Thread End Type, PN25 / Class250

-35-

Page 36: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-5-

Standard Screens

Dimensions (mm)

Size 50 65 80 100 125 150 200 250 300 350 400 450 500 600

L 230 273 293 349 417 467 545 664 770 960 1079 1168 1275 1450

H 116 181 195 230 285 337 382 473 554 740 840 902 990 1134

Plug 1/2" 1" 1" 1" 1-1/4" 1-1/2" 1-1/2" 2" 2" 2" 2" 2" 2" 2"

Notes 1. Flanges conform to EN1092-2 PN16 or ANSI 125. Other flange types are available.

2. Design, dimensions and materials are subject to change without notice.

Size Hole Dia. Free Flow Area

DN50 to 80 1.5mm 33%

DN100 to DN300 3.0mm 40%

-36-

Figure Number:

7104

Working Pressure and Temperature

Nominal Pressure 16bar / 225psi

Working Temperature -10℃ to 65℃

Materials List

Part Name Material EN Spec. ASTM Spec.

Body Cast Bronze 1982 CC491K B62 C83600

Cover Cast Bronze 1982 CC491K B62 C83600

Screen Stainless Steel SS304 SS304

Gasket Teflon / Graphite Commercial Commercial

Plug Cast Bronze 1982 CC491K B62 C83600

Y-Strainer Cast Bronze, PN16 / Class150

Page 37: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-6-

Standard Screens

Dimensions (mm) Size 50 65 80 100 125 150 200 250 300 350 400 450 500 600

L 207 210 251 292 334 378 475 511 680 769 842 842 842 1054

A 225 250 295 330 370 400 510 665 760 930 980 1010 1110 1690

B 135 155 190 205 215 235 295 340 405 585 590 590 600 1175

Plug 1/2” 3/4” 3/4” 1” 1” 1” 1-1/2” 1-1/2” 2” 2” 2” 2” 2” 2”

Notes 1. Flanges conform to EN1092-2 PN16 / ANSI 125 or EN1092-2 PN25 / ANSI 250.

2. Other flange types are available.

3. Design, dimensions and materials are subject to change without notice.

Size Hole Dia. Free Flow Area

DN50 to 80 1.5mm 33%

DN100 to DN600 3.0mm 40%

Figure Number 7105 Working Pressure at 16 bar or Class 125

7108 Working Pressure at 25 bar or Class 250

Working Pressure and Temperature

PN16 / Class 125 PN25 / Class 250

DN50 to DN300:

16 bar / 200psi

DN350 to DN600:

16 bar / 150psi

DN50 to DN300:

25 bar / 500psi

DN350 to DN600:

21 bar / 300psi

Working Temperature: -10℃ to 120℃

Materials List

Part Name Material EN Spec. ASTM Spec.

7105 Cast Iron EN-JL1040 A126 Class B Body

7108 Ductile Iron EN-JS1050 A536 65-45-12

7105 Cast Iron EN-JL1040 A126 Class B Cover

7108 Ductile Iron EN-JS1050 A536 65-45-12

Screen Stainless Steel SS304 SS304

Gasket Teflon / Graphite Commercial Commercial

7105 Cast Iron EN-JL1040 A126 Class B Plug

7108 Ductile Iron EN-JS1050 A536 65-45-12

Basket Strainer Flanged End Type

-37-

Page 38: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-7-

Standard Screens

Dimensions (mm)

Size 50 65 80 100 125 150 200 250 300 350 400 450 500 600

L 207 222 251 292 334 378 475 511 680 769 842 842 842 1054

A 220 250 285 340 370 390 510 665 760 930 980 1010 1110 1690

B 122 140 155 195 215 215 295 340 405 585 590 590 600 1175

Plug 1/2” 3/4” 3/4” 1” 1” 1” 1-1/2” 1-1/2” 2” 2” 2” 2” 2” 2”

Notes

1. Flanges conform to EN1092-2 PN16 or ANSI 125. Other flange types are available.

2. Design, dimensions and materials are subject to change without notice.

Size Hole Dia. Free Flow Area

DN50 to 80 1.5mm 33%

DN100 to DN600 3.0mm 40%

Figure Number

7106

Working Pressure and Temperature

Nominal Pressure 16bar / 225psi

Working Temperature -10℃ to 65℃

Materials List

Part Name Material EN Spec. ASTM Spec.

Body Cast Bronze 1982 CC491K B62 C83600

Cover Cast Bronze 1982 CC491K B62 C83600

Screen Stainless Steel SS304 SS304

Gasket Teflon / Graphite Commercial Commercial

Plug Cast Bronze 1982 CC491K B62 C83600

Basket Strainer Cast Bronze, PN16 / Class150

-38-

Page 39: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-1-

Dimensions (mm)

Size 15 20 25 32 40 50 65 80 100 125 150 200

DIN 115 120 125 130 140 150 170 180 190 200 210 400

NF 142 154 160 172 186 200 L

MSS 108 117 127 140 165 178 191 203 229 254 268 292

H 70 75 85 105 110 115 130 140 155 195 240 325

Notes

1. Face to face dimensions:

Fig. 4102: conforms to DIN 3202.

Fig. 4103: conforms to ANSI B16.10.

Fig. 4104: conforms to NF29323.

2. Top flange ends according to ISO5211.

3. Flanges conform to EN1092-2 PN16 or ANSI 125. Other flange types are available.

Ball Valve DIN / NF / MSS SP-72, PN16 / Class125

Figure Number: 4102 Conform to DIN standard.

4103 Conform to MSS standard.

4104 Conform to NF standard.

Working Pressure and Temperature

Nominal Pressure 16bar / 200psi

Working Temperature -10℃ to 120℃

Materials List:

Component Material EN Spec. ASTM Spec.

Body Ductile Iron EN-JS1050 A536 65-45-12

End Cap Ductile Iron EN-JS1050 A536 65-45-12

Ball Stainless Steel BS970 304S15 AISI 304

Stem Stainless Steel BS970 304S15 AISI 304

Body Seat Teflon + Graphite Commercial Commercial

Packing Teflon + Graphite Commercial Commercial

O-Ring Viton Commercial Commercial

Stopper Stainless Steel BS970 304S15 AISI 304

Handle Carbon Steel Mill Steel Mill Steel

-39-

Page 40: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-1-

Dimensions (mm) Size L±5 Axial Compression Axial Elongation Lateral Movement Angular Movement 32 95 9 6 9 15° 40 95 10 6 9 15° 50 105 10 7 10 15° 65 115 13 7 11 15° 80 130 15 8 12 15° 100 135 19 10 13 15° 125 165 19 12 13 15° 150 180 20 12 14 15° 200 205 25 16 22 15° 250 240 25 16 22 15° 300 260 25 16 22 15° 350 265 25 16 22 15° 400 265 25 16 22 15° 450 265 25 16 22 15° 500 265 25 16 22 15° 600 265 25 16 22 15°

Note: Flanges conform to EN1092-2 PN10 / 16 or ANSI B16.1 Class125. Other flange types are available.

Rubber Expansion Joint Single Sphere Type

Figure Number 8101E EPDM Cover

8101N NBR Cover

8101P Neoprene Cover

Materials List No. Part Name Material

1 Body EPDM, NBR or Neoprene

2 Reinforcing wire Spring Steel wire

3 Flange Carbon Steel

Operating Conditions Operating Pressure: 16 Bar

Explosive Pressure: 45 Bar

Vacuum Rating: 750mmHg

Medium Air, Water, Oil, Acid, Alkali etc.

L

-40-

Page 41: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-2-

Dimensions (mm)

Size L±5 Axial Compression Axial Elongation Lateral Movement Angular Movement α1+α2

32 175 20 10 20 30° 40 175 20 10 20 30° 50 175 20 10 20 30° 65 175 20 10 20 30° 80 175 20 10 20 30° 100 225 30 15 25 30° 125 225 30 15 25 30° 150 225 30 15 25 30° 200 325 40 20 30 30° 250 325 40 20 30 30° 300 325 40 20 30 30° 350 350 40 20 30 30° 400 350 40 20 30 30° 450 350 45 25 30 30° 500 350 45 25 30 30° 600 350 45 25 30 30°

Note: Flanges conform to EN1092-2 PN10 / 16 or ANSI B16.1 Class125. Other flange types are available.

Figure Number 8102E EPDM Cover

8102N NBR Cover

8102P Neoprene Cover

Materials List No. Part Name Material

1 Body EPDM, NBR or Neoprene

2 Carcass Nylon Cord Fabric

3 Reinforcing wire Spring Steel wire

4 Flange Carbon Steel

Operating Conditions Operating Pressure: 16 Bar

Explosive Pressure: 45 Bar

Vacuum Rating: 650mmHg

Medium Air, Water, Oil, Acid, Alkali etc.

Rubber Expansion Joint Double Sphere Type

Working Pressure and Temperature Working Pressure 16bar

Working Temperature

EPDM: -10℃ to 120℃

NBR: -10℃ to 82℃

Neoprene: -10℃ to 110℃

-41-

Page 42: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-3-

Dimensions (mm)

Size L Axial Compression Axial Elongation Lateral Movement Angular Movement α1+α2

20(3/4”) 200 22 5~6 22 45°

25(1”) 200 22 5~6 22 45°

32(1-1/4”) 200 22 5~6 22 45°

40(1-1/2”) 200 22 5~6 22 45°

50(2”) 200 22 5~6 22 45°

65(2-1/2”) 240 22 5~6 22 45°

Note: Union Coupling dimensions are in accordance with ANSI standard, BS standard, DIN standard, JIS standard.

Figure Number 8701E EPDM Cover

8701N NBR Cover

8701P Neoprene Cover

Working Pressure and Temperature Working Pressure 16bar

Working

Temperature

EPDM: -10℃ to 120℃

NBR: -10℃ to 82℃

Neoprene: -10℃ to 110℃

Materials List No. Part Name Material

1 Body EPDM, NBR or Neoprene

2 Carcass Nylon Cord Fabric

3 Reinforcing wire Spring Steel wire

4 Flange Carbon Steel

Operating Conditions Operating Pressure: 16 Bar

Explosive Pressure: 45 Bar

Vacuum Rating: 400mmHg

Medium Air, Water, Oil, Acid, Alkali etc.

Rubber Expansion Joint Double Sphere Union Type

-42-

Page 43: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange

Fivalco○R

-1-

Materials List

Installing Dimensions Size Inlet Size Outlet Orifice Size

1/2" 1/2" BSP or NPT 1/2" BSP or NPT 1/16"

3/4" 3/4" BSP or NPT 1/2" BSP or NPT 1/16"

1" 1" BSP or NPT 1/2" BSP or NPT 1/16"

No. Part Name Material EN Spec. ASTM Spec.

1 Body Cast Iron EN-JL1040 A126 Class B

2 Cover Cast Iron EN-JL1040 A126 Class B

3 Lever Frame Stainless Steel BS970 304S15 AISI 304

4 Seat Stainless Steel BS970 304S15 AISI 304

5 Float ball Stainless Steel BS970 304S15 AISI 304

6 Gasket EPDM Commercial Commercial

7 Cover Bolt Carbon Steel Carbon Steel A307 B

8 Float Arm Stainless Steel BS970 304S15 AISI 304

9 Orifice Button Viton Commercial Commercial

10 Pivot Pin Stainless Steel BS970 304S15 AISI 304

11 Pin Retainer Stainless Steel BS970 304S15 AISI 304

12 Pipe Plug Brass CuZn39Pb3 B16 C36000

13 Locator Stainless Steel BS970 304S15 AISI 304

Automatic Air Vent Valve PN16 / 225PSI

Figure Number 9701

-43-

Page 44: EN 593 / MSS SP-67, Wafer Type, PN16 / Class125file.seekpart.com/keywordpdf/2011/3/22/201132274823457.pdf · Designed and tested in accordance with EN 593 or MSS SP-67. 2. Flange