Datasheet - Accueil Lenzing-Plastics-France techniques.pdf · Datasheet Polypropylene film foamed...
Transcript of Datasheet - Accueil Lenzing-Plastics-France techniques.pdf · Datasheet Polypropylene film foamed...
Datasheet Polypropylene film foamed foamed monoaxial stretched film of closed-cell structure PP-S
Width: 4-1.400 mm, in increments of 5 mm Standard:1.200 mm
Material: Polypropylene
Types: Each type is determined by thickness and width as follows: “PP-S / (thickness in μm) x (width in mm)“, e.g. PP-S / 130 x 20 Description of types: PP-S / 80 stretched film, natural, 80 μm PP-S / 100 stretched film, natural, 100 μm PP-S / 130 stretched film, natural, 130 μm PP-S / 150 stretched film, natural, 150 μm PP-S / 170 stretched film, natural, 170 μm PP-S / 200 stretched film, natural, 200 μm PP-S / 300 stretched film, natural, 300 μm
Values Thickness 80 Density (calculated) g/cm³ 0,52
Weight per unit area EN 22 286 g/m2 42
Tensile strenght, long. ISO 527 N/mm² 100
Melting range DSC °C 160-170
Hot air shrinkage, long. (100°C/10 min)
BS 4611 A2 % ≤ 6
Elongation at break,
long., max ISO 527 % 25
Max. processing temperature °C ca. 225
Relative permittivity DIN 53 1,9
Dielectric strength DIN 53 481 kV/mm ≥ 10
Thermal resistance DIN 52 612 W/mK 0,08
100 0,52
52
100
25
≤ 6
160-170
ca. 225
1,9
≥ 10
0,08
130 0,52
68
110
25
≤ 6
160-170
ca. 225
1,9
≥ 15
0,08
150 170 200 0,51 0,51 0,51
77 85 100
110 120 100
25 25 25
≤ 6 ≤ 6 ≤ 6
160-170 160-170 160-170
ca. 225 ca. 225 ca. 225
1,9 1,9 1,9
≥ 15 ≥ 20 ≥ 20
0,08 0,08 0,08
300 0,51
165
70
35
≤ 6
160-170
ca. 225
1,9
≥ 25
0,08
Properties:
Lenzing Plastics GmbH & Co KG · Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
Colour: natural (transparent)
Roll Dimension: Mother rolls Core : 153 mm cardboard Width: 500 - 1.400 mm Runnig length: max. 6.000 m, depending on outer diameter
Roll Dimension: Pads Cores Inner—ø mm Thickness mm Material Type 76,6 11 cardboard 76 (3“) 153 14 cardboard 150 Roller outer-ø, mm: Outer diameter between 230 and 700 mm Tolerances: -20 mm / + 0 mm Front side of rolls: tolerance of layers max. ± 2 mm Planarity: tolerance of diameter max. ± 2 mm End marking: according to customers desire Joints: on both sides, brown PET adhesive tape, layer on layer thickness: 50 μm, width: 50mm max. number of joints: 2 per roll
Roll Dimension: Traverse-wound spools Cores: 76 mm cardboard Core length: 300 mm Core thickness: 7 mm Winding length: 280 mm Roll-outer-ø: max. 380 mm Film width: 5-30 mm
Datasheet Polypropylene film foamed
Subject to alterations! © 2014 by Lenzing Plastics
Lenzing Plastics GmbH & Co KG · Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
Datasheet Polypropylene film foamed, soft non-stretched film of closed-cell structure
Width: 10 -1.000 mm, in increments of 5 mm
Material: Polypropylene
Types: Each type is determined by thickness and width as follows: “PP-SS / (thickness in μm) x (width in mm)“, e.g. PP-SS / 350 x 20 Description of types: PP-SS / 300 unstretched film, natural, 300 μm PP-SS / 350 unstretched film, natural, 350 μm
Values Thickness 300 350 Density (calculated) g/cm³ 0,6 0,6
Weight per unit area EN 22 286 g/m2 170 210
Tensile strenght, long. ISO 527 N/mm² 20 20
Elongation at break, long., max ISO 527 % 230 230
Hot air shrinkage, long. (100°C/10 min) BS 4611 A2 % ≤ 6 ≤ 6
Melting range DSC °C 160-170 160-170
Max. processing temperature °C ca. 225 ca. 225
Relative permittivity DIN 53 483/2 1,9 1,9
Dielectric strength DIN 53 481 kV/mm ≥ 25 ≥ 25
Thermal resistance DIN 52 612 W/mK 0,08 0,08
Properties:
Lenzing Plastics GmbH & Co KG · Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
Colour: natural (transparent)
Roll Dimension: Mother rolls Core : 153 mm cardboard, wall thickness 14 mm Width: 500 mm Runnig length: max. 1000 m
Roll Dimension: Pads Cores Inner—ø mm Thickness mm Material Type 76,6 11 cardboard 76 (3“) 153 14 cardboard 150 Roller outer-ø, mm: Outer diameter between 230 and 700 mm Tolerances: -20 mm / + 0 mm Front side of rolls: tolerance of layers max. ± 2 mm Planarity: tolerance of diameter max. ± 2 mm End marking: according to customers desire Joints: on both sides, brown PET adhesive tape, layer on layer thickness: 50 μm, width: 50mm max. number of joints: 2 per roll
Datasheet Polypropylene film foamed, soft
Subject to alterations! © 2014 by Lenzing Plastics
Lenzing Plastics GmbH & Co KG · Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
Datasheet Polypropylene film solid monoaxial stretched film of PP-copolymers PP-K
Width: 10—1.500 mm, in increments of 5 mm Standard: 1.200 mm
Material: Polypropylene
Types: Each type is determined by thickness and width as follows: “PP-K / (thickness in μm) x (width in mm)“, e.g. PP-K / 50 x 20 Description of types: PP-K / 35 stretched film, natural, 35 μm PP-K / 50 stretched film, natural, 50 μm PP-K / 75 stretched film, natural, 75 μm
Values Thickness 35 Density (calculated) g/cm³ 0,91
Weight per unit area EN 22 286 g/m2 32
Tensile strenght, long. ISO 527 N/mm² 300
Melting range DSC °C 160-170
Hot air shrinkage, long. (100°C/10 min) BS 4611 A2 % ≤ 6
Elongation at break, long., max ISO 527 % 50
Max. processing temperature °C ca. 225
Relative permittivity DIN 53 483/2 2,4
Dielectric strength DIN 53 481 kV/mm ≥ 250
Thermal resistance DIN 52 612 W/mK 0,19
50 0,91
46
280
50
≤ 6
160-170
ca. 225
2,4
≥ 250
0,19
75 0,91
68
260
55
≤ 6
160-170
ca. 225
2,4
≥ 250
0,19
Properties:
Lenzing Plastics GmbH & Co KG · Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
Colour: natural (transparent)
Roll Dimension: Mother rolls Core : 76, 153 mm cardboard Width: 300, 500 mm Runnig length: max. 600 m
Roll Dimension: Pads Cores Inner—ø mm Thickness mm Material Type 76,6 11 cardboard 76 (3“) 153 14 cardboard 150 Roller outer-ø, mm: Outer diameter between 180 and 500 mm Tolerances: -20 mm / + 0 mm Front side of rolls: tolerance of layers max. ± 2 mm Planarity: tolerance of diameter max. ± 2 mm End marking: according to customers desire Joints: on both sides, brown PET adhesive tape, layer on layer thickness: 50 μm, width: 50mm max. number of joints: 2 per roll
Roll Dimension: Traverse-wound spools Cores: 76 mm cardboard Core length: 300 mm Core thickness: 7 mm, 10 mm Winding length: 280 mm Roll-outer-ø: max. 380 mm Film width: 5-30 mm
Datasheet Polypropylene film solid
Subject to alterations! © 2014 by Lenzing Plastics
Lenzing Plastics GmbH & Co KG · Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
Datasheet Polyester film, biaxially oriented PET film
Width: 5-1.200 mm, in increments of 5mm
Material: Polyester (PET)
Types: Each type is determined by thickness and width as follows: “PET / (thickness in μm ) x (width in mm)“, e.g.: PET / 23 x 20 Description of types: PET / 23 natural, 23 μm PET / 36 natural, 36 μm PET / 50 natural, 50 μm
Values Thickness 23 36 50
Weight per unit area g/m³ 32,2 50,4 70
Tensile strenght, long. MD N/mm² ≥180 ≥180 ≥180
Elongation at break MD % ≥80 ≥80 ≥80
Melting range °C 255-260 255-260 255-260
Heat shrinkage,
(150°Cx30 min) MD % ≤2 ≤2 ≤2
Properties:
Colour: natural (transparent)
Printing: optional possible
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-3626 · E-mail: [email protected] · www.lenzing-plastics.com
Roll Dimension: Mother rolls Cores : 76, 153 mm cardboard Width: 1200 mm Outer ø: max. 800 mm
Roll Dimension: Pads Cores Inner—ø mm Thickness mm Material Type 76,6 11 cardboard/plastics 76 (3“) 153 8 cardboard/plastics 150 Roller-outer-ø, mm Outer diameter between 180 an 700 mm: Tolerances: -20 mm / +0 mm Front side of rolls: tolerance of layers max. ± 2 mm Planarity: tolerance of diameters max. ± 2 mm
Roll Dimension: Traverse-wound spools Core-inner-ø: 76 mm cardboard Core length: 300 mm Wall thickness: 7 mm, 10 mm Winding length: 280 mm Roller-outer-ø: max. 380 mm Film width: 5-30 mm
Datasheet
Polyester film, biaxially oriented PET film
Subject to alterations! © 2014 by Lenzing Plastics
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-3626 · E-mail: [email protected] · www.lenzing-plastics.com
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-3626 · E-mail: [email protected] · www.lenzing-plastics.com
Datasheet Cable Identification Tape monoaxial streched polypropylene tape, coloured
Width: 3,0 mm ± 0,2 mm (standard) 4,0 mm ± 0,2 mm 5,0 mm ± 0,2 mm
Polymer: Polypropylene
Thickness: Values Tolerances 50 μm 45-55 μm 80 μm 75-85 μm
Values
Thickness DIN 53 370 μm 50 50
Width mm 3 4
Titer DIN 53 830/3 dtex 1370 1820
Breaking force ISO 527 N ≥51 ≥64
Elongation at break ISO 527 % ≥20 ≥19
Shrinkage BS 4611 A2 % ≤5 ≤5
50 80
5 3
2280 2190
≥77 ≥81
≥18 ≥20
≤5 ≤5
80 80
4 5
2920 3650
≥90 ≥100
≥20 ≥20
≤5 ≤5
Properties:
Colours: Colour Colour-code
natural - - - red F 0102 orange F 1105 yellow F 2072 green F 3128 blue F 4033 violet F 5014 brown F 7048 white F 8022 grey F 9011 black F 9012
Optional: High tenacity, e.g. 50 μm x 3 mm, min. 69 N
Core-dimensions
Datasheet Cable Identification Tape monoaxial streched polypropylene tape, coloured
Material P P P
L mm 170 220 110
D i mm 92 92 92
d mm 8 8 8
slit
unslit
s
D a** mm 200 200 200
B mm 160 200 100
as narrow as possible
P P K+P
128 170 105
82 129 65
8 8 K5 / P7
200 200 150
118 160 98
P
170
52
7
150
160
P
175
92
8
200
165
P
170
107
8
200
160
** standard, other outer diameters on request
L lenght of core P cardboard D i inner diameter of core K plastic d wall thickness D a outer diameter of roll B winding width Other diameters on request Subject to alteration!
© by Lenzing Plastics 2014
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-3626 · E-mail: [email protected] · www.lenzing-plastics.com
Cable Identification Tape Standard Colours
Colour No.
F 8022
F 2072
F 1105
F 0102
F 3128
F 4033
F 5014
F 9011
F 9012
F 7048
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-3626 · E-mail: [email protected] · www.lenzing-plastics.com
Colour
White
Yellow
Orange
Red
Green
Blue
Violet
Grey
Black
Brown
Above color-swatches should provide a fair impression of the shade of the product – as usual in trade, certain deviations, due to variations in pigmentation, do however occur.
Cable Identification Tape Standard Colours
Colour No.
F 8022
F 2072
F 1105
F 0102
F 3128
F 4033
F 5014
F 9011
F 9012
F 7048
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-3626 · E-mail: [email protected] · www.lenzing-plastics.com
Colour
White
Yellow
Orange
Red
Green
Blue
Violet
Grey
Black
Brown
Above color-swatches should provide a fair impression of the shade of the product – as usual in trade, certain deviations, due to variations in pigmentation, do however occur.
Datasheet Cable Identification Tapes Printed monoaxial streched tapes made of polypropylene coloured
Width: 3,0 mm ± 0,2 mm 5,0 mm ± 0,2 mm
Polymer: Polypropylene On request: PET (23 μm x 5mm) Laminated PET Tapes (PET 23 μm / PET 23 μm) Polyamid
Thickness: Values Tolerances 50 μm 45-55 μm 80 μm 75-85 μm
Values Thickness DIN 53 370 μm 50 50
Width mm 5 3
Titer DIN 53 830/3 dtex 2280 1370 Breaking force ISO 527 N ≥77 ≥51
Elongation at break ISO 527 % ≥18 ≥20
Shrinkage
HL 100 / 10 BS 4611 A2 % ≤5 ≤5
80
5
3650 ≥100
≥20
≤5
80
3
2190 ≥81
≥20
≤5
Properties:
Printing: Ink—jet for subsequential meter marking, numbers and texts Flexoprinting for numbers, texts, logos & colours
Colours: Colour Colour-code
natural - - - yellow F 2072 orange F 1105 red F 0102 green F 3128 blue F 4033 violet F 5014 grey F 9011 black F 9012 brown F 7048
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-3626 · E-mail: [email protected] · www.lenzing-plastics.com
Core-dimensions
Datasheet Cable Identification Tapes Printed monoaxial streched tapes made of polypropylene coloured
Material P P K+P
L mm 170 110 105
D i mm 92 92 65
d mm 8 8 K5 / P7
slit
unslit
s
D a** mm 200 180 150
B mm 160 100 98
as narrow as possible
** standard, other outer diameters on request
L lenght of core P cardboard D i inner diameter of core K plastic d wall thickness D a outer diameter of roll B winding width Other diameters on request Subject to alteration!
© by Lenzing Plastics 2014
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-3626 · E-mail: [email protected] · www.lenzing-plastics.com
Lenzing Plastics GmbH & Co KG · Werkstraße 2, A-4860 Lenzing, AustriaPhone: +43 (0) 7672 701-3794 · E-mail: [email protected] · www.lenzing-plastics.com
Cable Identification TapePrinted
No real film samples, just graphics
Flexoprinting
Texts
Logos
Numbers
Colours
Ink-jet
Subsequential / incrementing meter marking, numbers
LENzING PLASTICS www.LENzING-PLASTICS.COM
5. 5. 5. 5. 5.
Datasheet S - PTFE Films & Tapes, sintered
Width: 6 - 190 mm
Material: PTFE (Polytetrafluorethylene) Natural colour
Types: Each type is determined by thickness and width as follows: “S-PTFE / (thickness in μm ) x (width in mm)“, eg.: S-PTFE / 50 x 20 Description of types: S-PTFE / 50 sintered film, 50 μm S-PTFE / 100 sintered film, 100 μm
Standard Values
• Density (calculated) g/cm³ 2,15
• Tensile Strength (long.) ISO 527 N/mm² 40
• Elongation (long.) ISO 527 % 330
Typical Properties:
Thickness: Thickness range: 25 μm - 100 μm Standard Values Tolerances 25 μm 22 - 28 μm 35 μm 32 - 38 μm 50 μm 47 - 53 μm 100 μm 97 - 103 μm
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-3951 · E-mail: [email protected] · www.lenzing-plastics.com
Typical Packaging: 76 mm ID cores (plastic) flat pads or parallel winding on spools
Roll Outer ø , mm Depending on thickness & width between 150 and 300 mm Tolerances: -50 mm / +0 mm
Storage & Handling: Like many other materials, PTFE has a “memory“ which will cause the tape to try and recover its original shape. This is particularly an issue with expanded tapes, which try to retract back to their original density. It is very important therefore to store the material in a cool, clean & dry environment where the temperature should ideally stay under +19°C at all times.
Datasheet S - PTFE Films & Tapes, sintered
Subject to alterations! © 2014 by Lenzing Plastics
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-3951 · E-mail: [email protected] · www.lenzing-plastics.com
Datasheet ST - PTFE Films & Tapes sintered, stretched
Width: 6 -100 mm
Material: PTFE (Polytetrafluorethylene) Natural colour
Types: Each type is determined by thickness and width as follows: “PTFE / (thickness in μm ) x (width in mm)“, eg.: ST-PTFE / 35 x 30 Description of types: ST-PTFE / 25 sintered, stretched film, 25 μm ST-PTFE / 35 sintered, stretched film, 35 μm ST-PTFE / 50 sintered, stretched film, 50 μm
Values
• Density (calculated) g/cm³ 2,0
• Tensile strenght, long. ISO 527 N/mm² 120
• Elongation at break, long. ISO 527 % 100
Properties: variable • fixed
Thickness: Thickness range: 25 μm - 50 μm Values Tolerances 25 μm 20 - 30 μm 35 μm 30 - 40 μm 50 μm 45 - 55 μm
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-3951 · E-mail: [email protected] · www.lenzing-plastics.com
Typical Packaging: 76 mm ID cores (plastic) flat pads or parallel winding on spools
Roll Outer ø , mm Depending on thickness & width between 150 and 300 mm Tolerances: -50 mm / +0 mm
Storage & Handling: Like many other materials, PTFE has a “memory“ which will cause the tape to try and recover its original shape. This is particulary an issue with ex-panded tapes, which try to retract back to their original density. It is very important therefore to store the material in a cool, clean & dry environment where the temperature should really ideally stay under 19°C at all times.
Datasheet ST- PTFE Film, Tapes skived / sintered, stretched
Subject to alterations! © 2014 by Lenzing Plastics
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-3951 · E-mail: [email protected] · www.lenzing-plastics.com
Datasheet PTFE-PEX Films & Tapes, unsintered
Width: 1,5 - 200 mm
Material: PTFE (Polytetrafluorethylene), natural / clear standard and custom colors laser printable
Types: Each type is determined by thickness and width as follows: “PEX / (thickness in μm ) x (width in mm)“, eg.: PEX / 50 x 20 Description of tyes: PEX / 50 unsintered film, 50 μm PEX / 100 unsintered film, 100 μm
Standard Values
• Density (calculated) g/cm³ 1.6
• Tensile Strength (long.) ISO 527 N/mm² 15
• Elongation (long.) ISO 527 % 150
Typical Properties:
Thickness: Thickness range: 50 μm—254 μm Standard Values Tolerances 50 μm 45 - 55 μm 76 μm 71 - 81 μm 100 μm 95 - 105 μm 254 μm 244 - 264 μm
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-3951 · E-mail: [email protected] · www.lenzing-plastics.com
Typical Packaging: 76 mm ID cores (plastic) flat pads or traverse ‚step pack‘ winding on spools traverse packages allow the user to get more length and narrower widths when needed
Roll Outer ø , mm Depending on thickness & width between 150 and 300 mm Tolerances: -50 mm / +0 mm
Storage & Handling: Like many other materials, PTFE has a “memory“ which will cause the tape to try and recover its original shape. This is particularly an issue with expanded tapes, which try to retract back to their original density. It is very important therefore to store the material in a cool, clean & dry environment where the temperature should ideally stay under +19°C at all times.
Datasheet PTFE - PEX Films & Tapes, unsintered
Subject to alterations! © 2014 by Lenzing Plastics
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-3951 · E-mail: [email protected] · www.lenzing-plastics.com
PTFE-PEX Films & Tapes unsintered
Standard Colours
(Shade after sintering) Colour Colour No. Shade acc. to
RAL No.
black 090411 9017
blue dark 122213 5005
blue light 121511 5012
brown 111110 8007
green dark 110510 6016
green light 110511 6024
grey 101310 7040
orange 130412 2009
red 122810 3020
white 121610 9016
yellow 112812 1018
All our colour pigments are heavy-metal-free, RoHS and REACH compliant and have a very good thermal stability.
Lenzing Plastics GmbH & Co KG · Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701– 3951 · E-mail: [email protected] · www.lenzing-plastics.com
Above color-swatches should provide a fair impression of the shade of the sintered product – as usual in trade, certain deviations, due to variations in pigmentation, do however occur.
Datasheet
LD-PTFE Films & Tapes, low density
Width: 1,5 -150 mm
Material: PTFE (Polytetrafluorethylene) expanded, natural colour standard density: 0,7 g /cm³
Types: each type is determined by thickness and width as follows: “LD-PTFE / (thickness in μm ) x (width in mm)“, eg.: LD-PTFE / 76 x 20 Description of types: LD-PTFE / 76 low density film 76 μm LD-PTFE / 254 low density film 254 μm
Typical Properties:
Thickness: Thickness range: 50 - 254 μm Standard Values Tolerances Standard Values Tolerances 50 μm 45 - 55 μm 152 μm 142 - 162 μm 76 μm 71 - 81 μm 203 μm 193 - 213 μm 102 μm 97 - 107 μm 254 μm 244 - 264 μm 127 μm 122 - 132 μm special types on request
Density: Standard Values Tolerances 0,7 g/cm³ 0,65 - 0,75 g/cm³ special types on request
Standard Values
• Density (calculated) g/cm³ 0.7
• Tensile Strength (long.) ISO 527 N/mm² 12 min
• Elongation (long.) ISO 527 % 70 min
• Shrinkage (long.) 200°C/15 min. % 15 - 45
Guideline for electrical properties:
• Dielectric constant (guideline) εr 1.4
• Dissipation factor (guideline) tan δ 10-4
1MHZ
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-3951 · E-mail: [email protected] · www.lenzing-plastics.com
Typical Packaging: 76 mm ID cores (plastic) flat pads or traverse “step pack“ winding on spools traverse packages allow the user to get more lengths and narrower widths when needed
Roll Outer ø , mm Depending on thickness & width between 150 and 250 mm Tolerances: -50 mm / +0 mm
Storage & Handling: Like many other materials, PTFE has a “memory“ which will cause the unsintered tape to try and recover its original shape. This is particularly an issue with expanded tapes, which try to retract back to their original density. It is very important therefore to store the material in a cool, clean & dry environment where the temperature should iideally stay under +19°C at all times.
Datasheet
LD-PTFE Films & Tapes, low density
Subject to alterations! © 2014 by Lenzing Plastics
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-3951 · E-mail: [email protected] · www.lenzing-plastics.com
Datasheet
LS-LD-PTFE Film, Tapes, low shinkage,low density
Width: 1,5 -150 mm
Material: PTFE (Polytetrafluorethylene) expanded, natural colour standard density 0.7g /cm³
Types: Each type is determined by thickness and width as follows: “LS-LD-PTFE / (thickness in μm ) x (width in mm)“, eg.: LS-LD-PTFE / 127 x 12,7 Description of types: LS-LD-PTFE / 76 low shrinkage, low density film, 76 μm
Typical Properties:
Thickness: Thickness range: 76 μm - 254 μm Standard Values Tolerances 76 μm 71 - 81 μm 102 μm 97 - 107 μm 127 μm 122 - 132 μm 203 μm 193 - 213 μm 254 μm 244 - 264 μm
Density: Standard Values Tolerances 0,7 g/cm³ 0,65 - 0,75 g/cm³ special types on request
Standard Values
• Density (calculated) g/cm³ 0.7
• Tensile Strength (long.) ISO 527 N/mm² 35
• Elongation (long.) ISO 527 % 55
• Shrinkage (long.) 200°C/15 min. % 5 - 10
Guideline for electrical properties:
• Dielectric constant (guideline) εr 1.4
• Dissipation factor (guideline) tan δ 10-4
1MHZ
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-3951 · E-mail: [email protected] · www.lenzing-plastics.com
Typical Packaging: 76 mm ID cores (plastic) pads or “step pack“ winding on spools traverse packages allow the user to get more lengths and narrower widths when needed
Roll Outer ø , mm Depending on thickness & width between 150 and 250 mm Tolerances: -50 mm / +0 mm
Storage & Handling: Like many other materials, PTFE has a “memory“ which will cause the material to try and recover ist original shape. This is particularly an issue with expanded tapes, which try to retract back to their original density. It is very important therefore to store the material in a cool, clean & dry environ-ment where the temperature should ideally stay under +19°C at all times.
Datasheet
LS-LD-PTFE Film, Tapes low shinkage,low density
Subject to alterations! © 2014 by Lenzing Plastics
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-3951 · E-mail: [email protected] · www.lenzing-plastics.com
Datasheet
LD-HRC-PTFE Films & Tapes, low density - „crush resistant“
Width: 1,5 - 60 mm
Material: PTFE (Polytetrafluorethylene) dimensionally stable expanded, natural colour fast elastic recovery superior crush resistant
Types: each type is determined by thickness and width as follows: “LD-HRC-PTFE / (thickness in μm ) x (width in mm)“, eg.: LD-HRC-PTFE / 76 x 20 Description of types: LD-HRC-PTFE / 50 low density - HRC film 50 μm LD-HRC-PTFE / 76 low density - HRC film 76 μm
Typical Properties:
Thickness: Thickness range: 50 - 125 μm Standard Values Tolerances 50 μm 45 - 55 μm 76 μm 71 - 81 μm special types on request
Density: Standard Values Tolerances 0,4 g/cm³ 0,35 - 0,45 g/cm³ 0,5 g/cm³ 0,45 - 0,55 g/cm³
Standard Values
• Density (calculated) g/cm³ 0.4
• Tensile Strength (long.) ISO 527 N/mm² >40
• Elongation (long.) ISO 527 % 20
• Shrinkage (long.) 200°C/15 min. % 15-35
Guideline for electrical properties:
• Dielectric constant (guideline) εr 1.4
• Dissipation factor (guideline) tan δ 10-4
1MHZ
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-3951 · E-mail: [email protected] · www.lenzing-plastics.com
Typical Packaging: 76 mm ID cores (plastic) flat pads or traverse “step pack“ winding on spools / without flanges traverse packages allow the user to get more lengths and narrower widths when needed
Roll Outer ø , mm Depending on thickness & width between 150 and 250 mm Tolerances: -50 mm / +0 mm
Storage & Handling: Like many other materials, PTFE has a “memory“ which will cause the unsintered tape to try and recover its original shape. This is particularly an issue with expanded tapes, which try to retract back to their original density. It is very important therefore to store the material in a cool, clean & dry environment where the temperature should iideally stay under +19°C at all times.
Datasheet LD-HRC-PTFE Films & Tapes, low density - „crush resistant“
Subject to alterations! © 2014 by Lenzing Plastics
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-3951 · E-mail: [email protected] · www.lenzing-plastics.com
Datasheet ed-CU-PET Laminate
Width: 5—20 mm, in increments of 1mm ± 0,5mm 20—1.000 mm, in increments of 5mm ± 0,5mm
Types: Each type is determined by thickness and width as follows: Description of types: ed-CU / PET 18/23 ed-CU 18 μm / PET 23 μm
Values Thickness 18/23
Weight per unit area (calculated) g/m2 187
Tensile strenght, long. ISO 527 N/mm² 80
Elongation at break, long. ISO 527 % 4
Thickness DIN 53 370 μm 44
Properties:
Material: Copper foil electrolytic (e-CU) Glue Polyester foil (PET)
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
Roll Dimension: Pads Core Inner-ø mm max.outer-ø mm max. width mm Material 76,6 400 30 cardboard or plastic 76,6 800 > 30 cardboard or plastic Tolerances: O/D: -20 mm / + 0 mm End marking: at customers option
Roll Dimension: Traverse-wound spools Core-inner-ø: 76,6 mm / cardboard Core length: 300 mm Wall thickness: 10 mm Winding length: max. 300 mm Spool-outer-ø: max. 380 mm Film width: 5—30 mm Package: plastic deposit plates Spool weight approx. 100 kg (76/300/380) Joints: standard: cross (30°) layer on layer PET adhesive tape on both sides
Datasheet ed-CU-PET Laminate
Subject to alterations! © 2014 by Lenzing Plastics
Roll Dimension: Mother rolls Core : 153 mm, wall thickness 14 mm Width: 1100 mm Outer ø: max. 800 mm, but max. 1400 kg per roll Joints: every 2000 rm
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
Datasheet CU-PET Laminate
Width: 5—20 mm, in increments of 1mm ± 0,5mm 20—650 mm, in increments of 5mm ± 0,5mm
Types: Each type is determined by thickness and width as follows: Description of types: CU / PET 20/23 CU 20μm / PET 23 μm
Values Thickness 20/23
Weight per unit area (calculated) g/m2 211
Tensile strenght, long. ISO 527 N/mm² 80
Elongation at break, long. ISO 527 % 15
Thickness DIN 53 370 μm 46
Properties:
Material: Copper foil rolled (CU) Glue Polyester foil (PET)
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
Roll Dimension: Pads Core Inner-ø mm max.outer-ø mm max. width mm Material 76,6 400 30 cardboard or plastic 76,6 800 > 30 cardboard or plastic Tolerances: O/D: -20 mm / + 0 mm End marking: at customers option
Roll Dimension: Traverse-wound spools Core-inner-ø: 76,6 mm / cardboard Core length: 300 mm Wall thickness: 10 mm Winding length: max. 300 mm Spool-outer-ø: max. 380 mm Film width: 5—30 mm Package: plastic deposit plates Spool weight approx. 100 kg (76/300/380) Joints: standard: cross (30°) layer on layer PET adhesive tape on both sides
Datasheet CU-PET Laminate
Subject to alterations! © 2014 by Lenzing Plastics
Roll Dimension: Mother rolls Core : 153 mm, wall thickness 14 mm Width: 650 mm Outer ø: max. 800 mm, but max. 1400 kg per roll
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
Datasheet
AL-PET-EMA Laminate
Width: 5-20 mm, in increments of 1mm ± 0,5mm 20-1.000 mm, in increments of 5mm ± 0,5mm
Material: Aluminium (AL) Glue Polyester (PET) Ethylene Methyl Acrylat (EMA-white)
Types: Each type is determined by thickness and width as follows: Description of types: AL 25 / PET 12 / EMA 25 (AL 25 μm / PET 12 μm / EMA 25 g/m²)
Values Thickness 25/12/25
Weight per unit area (calculated) g/m2 112
Tensile strenght, long. ISO 527 N/mm² 65
Elongation at break, long. ISO 527 % 18
Thickness DIN 53 370 μm 65
Max. temperature °C 300
Melting point DSC °C 80
Properties:
Lenzing Plastics GmbH & Co KG · Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
Roll Dimension: Mother rolls Core : 153 mm, wall thickness 14 mm Width: 1.045 mm Outer ø: max. 800 mm, but max. 1400 kg per roll
Roll Dimension: Pads Core Inner—ø mm max.outer—ø mm max. width mm Material 76,6 400 30 cardboard or plastic 76,6 800 > 30 cardboard or plastic Tolerances: O/D: -20 mm / + 0 mm End marking: at customers option
Roll Dimension: Traverse-wound spools Core-inner-ø: 76,6 mm / cardboard Core length: 300 mm Wall thickness: 10 mm Winding length: max. 300 mm Spool-outer-ø: max. 380 mm Film width: 5-30 mm Package: plastic deposit plates Joints: standard: cross (30°) layer on layer PET adhesive tape on both sides
Datasheet AL-PET-EMA Laminate
Subject to alterations! © 2014 by Lenzing Plastics
Lenzing Plastics GmbH & Co KG · Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
Lenzing Plastics GmbH & Co KG · Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
Datasheet AL-PAPER Laminate
Width: 5-20 mm, in increments of 1mm ± 0,5mm 20-1.000 mm, in increments of 5mm ± 0,5mm
Material: AL-film Glue Paper
Types: Each type is determined by thickness and width as follows: Description of types: AL-Paper 12-100 (AL 12 μm / Paper100 g/m²) AL-Paper 25-100 (AL 25 μm / Paper100 g/m²)
Values Thickness 12-100
Weight per unit area (calculated) g/m2 136
Tensile strenght, long. ISO 527 N/mm² 120
Elongation at break, long. ISO 527 % 2
Thickness DIN 53 370 μm 115
25-100
172
120
2
145
Properties:
Roll Dimension: Mother rolls Core : 153 mm, wall thickness 14 mm Width: 1.420 mm Outer ø: max. 1.100 mm, but max. 1500 kg per roll
Roll Dimension: Pads Core Inner—ø mm max.outer—ø mm max. width mm Material 76,6 400 30 cardboard or plastic 76,6 800 > 30 cardboard or plastic Tolerances: O/D: -20 mm / + 0 mm End marking: at customers option
Roll Dimension: Traverse-wound spools Core-inner-ø: 76,6 mm / cardboard Core length: 300 mm Wall thickness: 10 mm Winding length: max. 300 mm Spool-outer-ø: max. 380 mm Film width: 5-30 mm Package: plastic deposit plates Joints: standard: cross (30°) layer on layer PET adhesive tape on both sides
Datasheet AL-PAPER Laminate
Subject to alterations! © 2014 by Lenzing Plastics
Lenzing Plastics GmbH & Co KG · Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
Datasheet PET/PET– Vlies Laminate
Colour: natural Width: 5-20 mm, in increments of 1mm ± 0,5mm 20-1.000 mm, in increments of 5mm ± 0,5mm
Material:
PET film (Polyester) 12 μm Glue PET vlies 40 g
Description of the type:
PET 12 μm / PET-Vlies 40 g
Values
Weight per unit area +/- 5% (calculated) g/m2 61
Tensile strenght, long. ISO 527 N/mm² 7
Elongation at break, long. ISO 527 % 50
Properties:
Lenzing Plastics GmbH & Co KG · Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
Roll Dimension: Mother rolls Core : 153 mm, wall thickness 14 mm Width: 1.090 mm Outer ø: max. 1100mm, but max. 1500 kg per roll
Roll Dimension: Pads Inner—ø mm max. width mm Material 76,6 30 cardboard Outer-ø mm < 20 mm 400 mm ≥ 20 mm max.800 mm Tolerances: O/D: + 0 mm/-20 mm End marking: at customers option
Roll Dimension: Traverse—wound spools Core-inner-ø: 76,6 mm / cardboard Core length: 300 mm Wall thickness: 10 mm Winding length: max. 300 mm Spool-outer-ø: max. 380 mm Film width: 5—30 mm Package: plastic deposit plates Spool weight approx. 45 kg (76/300/380) Joints: standard: cross (30°) layer on layer
Datasheet PET/PET– Vlies Laminate
Subject to alterations! © 2014 by Lenzing Plastics
Lenzing Plastics GmbH & Co KG · Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
Datasheet PP- L / Laminate
Width: 5-20 mm, in increments of 1mm ± 0,5mm 20-1.000 mm, in increments of 5mm ± 0,5mm
Material: Polypropylene foamed (PP-S) Glue, red Polyester (PET)
Types: Each type is determined by thickness and width as follows: Description of types: PP-L 100/12 (PP-S 100 μm - PET 12 μm)
Values Thickness 100/12
Weight per unit area (calculated) g/m2 77
Tensile strenght, long. ISO 527 N/mm² 170
Elongation at break, long. ISO 527 % 20
Thickness DIN 53 370 μm 115
Properties:
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
Roll Dimension: Mother rolls Core : 153 mm, wall thickness 14 mm Width: 1.020 mm Outer ø: max. 800mm, but max. 1400 kg per roll
Roll Dimension: Pads Core Inner—ø mm max.outer—ø mm max. width mm Material 76,6 400 30 cardboard or plastic 76,6 800 > 30 cardboard or plastic Tolerances: O/D: -20 mm / + 0 mm End marking: at customers option
Roll Dimension: Traverse—wound spools Core-inner-ø: 76,6 mm / cardboard Core length: 300 mm Wall thickness: 10 mm Winding length: max. 300 mm Spool-outer-ø: max. 380 mm Film width: 5-30 mm Package: plastic deposit plates Joints: standard: cross (30°) layer on layer PET adhesive tape on both sides
Datasheet PP- L / Laminate
Subject to alterations! © 2014 by Lenzing Plastics
Lenzing Plastics GmbH & Co KG· Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
Datasheet AL-PET Laminate
Colours: red, blue, green, gold Width: 5-20 mm, in increments of 1mm ± 0,5mm
Material: AL film Glue PET film (Polyester)
Types: Each type is determined by thickness and width as follows: Description of types: AL– PET 9-12 (AL 9 μm / PET 12 μm) AL—PET 12-12 (AL 12μm / PET 12 μm) AL—PET 25-23 (AL 25 μm / PET 23 μm) AL—PET 37-12 (AL 37 μm / PET 12 μm) AL—PET 40-12 (AL 40 μm / PET 12 μm) AL—PET 50-12 (AL 50 μm / PET 12 μm) AL—PET 9-12-9 (AL 9 μm / PET 12 μm / AL 9 μm) AL—PET 9-15-9 (AL 9 μm / PET 15 μm/ AL 9 μm)
Values 9-12 12-23 37-12 40-12 50-12
Weight per unit area 43 67 120 128 152
Tensile strenght, long. 70 70 80 80 80
Elongation at break, long. 15 15 15 15 15
Thickness 24 38 52 55 65
Thickness
g/m2
N/mm²
%
μm
(calculated)
ISO 527
ISO 527
DIN 53 370
12-12
52
70
15
27
Properties:
Lenzing Plastics GmbH & Co KG · Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
12 12
Roll Dimension: Mother rolls Core : 153 mm, wall thickness 14 mm Width: 1.090 mm Outer ø: max. 1100mm, but max. 1500 kg per roll
Roll Dimension: Pads Core Inner—ø mm max.outer—ø mm max. width mm Material 76,6 400 30 cardboard or plastic 76,6 800 > 30 cardboard or plastic Tolerances: O/D: -20 mm / + 0 mm End marking: at customers option
Roll Dimension: Traverse—wound spools Core-inner-ø: 76,6 mm / cardboard Core length: 300 mm Wall thickness: 10 mm Winding length: max. 300 mm Spool-outer-ø: max. 380 mm Film width: 5—30 mm Package: plastic deposit plates Spool weight approx. 45 kg (76/300/380) Joints: standard: cross (30°) layer on layer PET adhesive tape on both sides
Datasheet
AL-PET Laminate
Subject to alterations! © 2014 by Lenzing Plastics
Lenzing Plastics GmbH & Co KG · Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
Datasheet AL-PVC Laminate
Width: 5-20 mm, in increments of 1mm ± 0,5mm 20-1.000 mm, in increments of 5mm ± 0,5mm
Material: AL-film Glue PVC (Polyvinylchlorid)
Types: Each type is determined by thickness and width as follows: Description of types: AL-PVC 25-25 (AL 25 μm - PVC 25 μm)
Values Thickness 25-25
Weight per unit area (calculated) g/m2 107
Tensile strenght, long. ISO 527 N/mm² 50
Elongation at break, long. ISO 527 % 11
Thickness DIN 53 370 μm 53
Properties:
Colour: green
Lenzing Plastics GmbH & Co KG · Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com
Roll Dimension: Mother rolls Core : 153 mm, wall thickness 14 mm Width: 1.090 mm Outer ø: max. 1.100 mm, but max. 1500 kg per roll
Roll Dimension: Pads Core Inner—ø mm max.outer—ø mm max. width mm Material 76,6 400 30 cardboard or plastic 76,6 800 > 30 cardboard or plastic Tolerances: O/D: -20 mm / + 0 mm End marking: at customers option
Roll Dimension: Traverse-wound spools Core-inner-ø: 76,6 mm / cardboard Core length: 300 mm Wall thickness: 10 mm Winding length: max. 300 mm Spool-outer-ø: max. 380 mm Film width: 5-30 mm Package: plastic deposit plates Joints: standard: cross (30°) layer on layer PET adhesive tape on both sides
Datasheet AL-PVC Laminate
Subject to alterations! © 2014 by Lenzing Plastics
Lenzing Plastics GmbH & Co KG · Werkstraße 2, 4860 Lenzing, Austria
Phone: +43 (0)76 72 701-2632 · E-mail: [email protected] · www.lenzing-plastics.com