AnnalsoftheConstantinBrancusiUniversityofTarguJiu,EngineeringSeries,No.2/2015

176

RADIAL BEARINGS CYLINDRICAL ROLLER EROSION PROCESSING ELECTRICAL

Drd. Ing. IOAN BADIU, Technical University of Cluj-Napoca Prof.univ.dr.ing. MARCEL S.POPA, Technical University of Cluj-Napoca

ABSTRACT: Cylindrical roller bearings take heavy radial loads that can operate at high speeds. They are manufactured in a wide variety of variants and sizes, especially with a row of rolls, and two or more rows, the next roll or roll cages. In cylindrical roller bearings, rollers are guided by fixed collar of one of the rings. In models with cage, collar ring with cage retained rollers can be extracted from the other ring. Therefore, mounting and dismounting of bearings in the hub become much easier, especially in those places where, due to the loading conditions are imperative need tight fits for both rings. Cylindrical roller bearings are assemblies consisting of a row outer rings, inner rings and roller cages. Outer rings can be trimmed on both sides and the interior have one or two edges. The cage prevents the roller contact during operation. Cylindrical roller bearings are very rigid, have a high radial load capacity and because the cage, are suitable for high speeds.

KEY WORDS : radial bearings, cylindrical roller, electrical erosion ,materials. 1.INTRODUCTION Bearings with the suffix E have a special set of rollers and are sized for bearing capacity maxim.Lagrele are dismantled, thereby facilitating assembly and disassembly. Both bearing rings can be fitted with interference fit. Cylindrical roller bearings with cage row can be used as free bearings, bearings and the bearing support conductoare.Multe types is provided in version X-life.Lagrele X-life quality driveways with a lower roughness and

accuracy are larger than comparable versions with X-life. The dimensioning identical capacity and lifetime of these bearings is superior. In certain embodiments, X-life bearings suspension can be dimensioned at a lower overall.

2. THE PROCESSING TECHNOLOGY OF BEARINGS

Fig .1. Electrical erosion machine processed ONA -AF-25

AnnalsoftheConstantinBrancusiUniversityofTarguJiu,EngineeringSeries,No.2/2015

176

Fig .2. Processing the circular orbit.

Fig .3. Radial bearings cylindrical roller

Fig .4. Cylindrical roller radial bearings Timken single row.

Fig .5. Timken The cylindrical roller Ball Bearings NN / NNU.

Fig .6. Cylindrical roller Ball Bearings Timken four rows.

Fig .7. The cylindrical roller radial bearings NSK single row

AnnalsoftheConstantinBrancusiUniversityofTarguJiu,EngineeringSeries,No.2/2015

177

Fig .8. NSK cylindrical roller bearings type NN/NNU.

Fig .9. Cylindrical roller bearings NSK four rows.

3.THE EXPERIMENTAL RESULTS PROCESSING ELECTRICAL EROSION

Fig .10. Table containing the values parameters of electrical erosion.

Fig .11. The reporting of parameters electrical

erosion wear.

Fig .12. The connection between electrical

erosion parameters.

Fig .13. The reporting of electric erosion

productivity parameters.

Fig .14. The reporting of electric erosion

productivity parameters.

AnnalsoftheConstantinBrancusiUniversityofTarguJiu,EngineeringSeries,No.2/2015

178

Fig .15. Table containing the values parameters

of electrical erosion.

Fig .16. The connection between electrical

erosion parameters.

Fig .17. The reporting of electric erosion

productivity parameters.

Fig .18. The reporting of electric erosion

productivity parameters.

Fig .19. The form 3D graphics parameters

electrical erosion.

Fig .20. The form 3D graphics parameters

electrical erosion.

Fig .21. Table containing the values parameters

of electrical erosion.

Fig .22. Table containing the values parameters

of electrical erosion.

AnnalsoftheConstantinBrancusiUniversityofTarguJiu,EngineeringSeries,No.2/2015

179

Fig .23. The form 3D graphics parameters

electrical erosion.

Fig .24. The form 3D graphics parameters

electrical erosion.

Fig .25.Table containing the values parameters

of electrical erosion.

Fig .26. Table containing the values parameters

of electrical erosion.

Fig .27. The form 3D graphics parameters

electrical erosion.

Fig .28. The form 3D graphics parameters

electrical erosion.

Fig .29. The form 3D graphics parameters

electrical erosion.

Fig .30. Graphical form of balls and their

values.

AnnalsoftheConstantinBrancusiUniversityofTarguJiu,EngineeringSeries,No.2/2015

180

Fig .31. Form 2D and electrical erosion

equation parameters.

Fig .32. Form 2D and electrical erosion

equation parameters.

Fig .33. Graphical form of electrical erosion

parameters.

Fig .34. Graphical form of electrical erosion

parameters.

Fig .35. Graphical form of electrical erosion

parameters.

Fig .36. Points that determine the erosion

parameters electrical lines.

Fig .37. The straight lines a electrical erosion

parameters.

Fig .38. The equations of the straight lines and

form 2D graphics.

AnnalsoftheConstantinBrancusiUniversityofTarguJiu,EngineeringSeries,No.2/2015

181

Fig .39. The equations of the straight lines and

form 2D graphics.

Fig .40. The equations of the straight lines and

form 2D graphics.

Fig .41. The equations of the straight lines and

form 2D graphics.

Fig .42. The intensity parameter values

expressed in percentage.

Fig .43. The intensity parameter values

expressed in percentage .

4.CONCLUSIONS Cylindrical roller bearings are manufactured in a variety of types and sizes, especially a row of rolls, and on two or more occasions, with cages or roll next roll. In cylindrical roller bearings, rollers are guided by lateral collar of one of inele.La fixed bearings with cages, collar ring with rollers retained by the cage can be extracted from the other ring, which means that the bearings are removed. Through this, mounting and dismounting of bearings in node becomes much easier, especially in those places where due to the loading conditions are necessary adjusted close to both inele.Rulmentii are provided at the ends downloaded roller generatrix, for which linear contact between rolls and rings great change in the sense voltages edge.

REFERENCES [1]Ailincai, G.: Studiul metalelor ,Institutul Politehnic Iasi, 1978. [2]Balc, N.: Tehnologii neconventionale, Editura Dacia Publishing House, Cluj-Npoca, 2001. [3]Bolundut, L.I.: Materiale si tehnologii neconventionale, Editura Tehnica-Info, Chisinau, 2012. [4]Buzdugan, Gh., .a. Vibraii mecanice, Editura Didactic i Pedagogic, Bucureti, 17. [5]Constantinescu, V., .a. Lagre cu alunecare, Editura Tehnic, Bucureti 1980. [6]Colan, H.: Studiul metalelor, Editura Didactica si Pedagogica , Bucuresti, 1983.

AnnalsoftheConstantinBrancusiUniversityofTarguJiu,EngineeringSeries,No.2/2015

182

[7]Domsa, A.: Materiale metalice in constructia de masini si instalatii, Editura Dacia, 1981. [8]Dai, P. 100.000 Technical and ICT Abbreviations and Acronyms. Vrnjaka Banja: SaTCIP Ltd., 2013. pp. 1200. ISBN 978-86-6075-001-5. []Dai, P. Analysis of the journal impact factor in field of mechanical engineering. Plenary and Invitation paper. In: Proceedings of the 11th International

in Mechanical Industry Volume 1, Sokobanja, Serbia, 15-18. September 2011. Edited by Predrag Dai. Vrnjaka Banja SaTCIP Ltd., 2011, pp. 62-70. ISBN 978-86-6075-027-5. [10] Dai, P.; Natsis, A. and Petropoulos, G.: Models of reliability for cutting tools: Examples in manufacturing and agricultural engineering. Strojniki vestnik Journal of Mechanical Engineering, Vol. 54, No. 2 (2008), pp. 122-130. ISSN 00392480. [11] Dai, P.; Franek, F.; Assenova, E. and Radovanovi, M. International standardization and organization in the field of tribology. Industrial Lubrication and Tribology (ILT) Journal, Vol. 55, No. 6 (2003), pp. 287-291. ISSN 0036-8792. Available on Web site: http://www.emeraldinsight.com/Insight/ ViewContentServlet?Filename=Published/EmeraldFullTextArticle/Articles/0180550605.html. [12] Gafianu, M. .a. Organe de maini, vol. 2. Editura Tehnic, Bucureti, 2002. [13]Nichici, A.: Prelucrarea prin eroziune electrica in constructia de masini, Editura Facla, Timisoara, 1983. [14]Olaru, D.N. Tribologie. Elemente de baz asupra frecrii, uzrii i ungerii, Litografia Institutului Politehnic Gheorghe Asachi, Iai, 15. [15] Popa,M.S.:Masini, tehnologii neconventionale si de mecanica fina-Editie Bilingva, Romana-Germana, Editura U.T.PRESS, Cluj-Napoca, 2003.

[16]Popa, M.S.: Tehnologii si masini neconventionale, pentru mecanica fina si microtehnica, Editura U.T.PRESS, Cluj-Napoca, 2005. [17]Popa, M.S.:Tehnologii inovative si procese de productie, Editura U.T.PRESS, Cluj-Napoca,2009. [18]Popescu, Luminia Georgeta Cristinel Popescu, Influena dispozitivelor de anclanare automat a rezervei asupra funcionrii ntreruptoarelor de cupl longitudinal, Analele Universitii Constantin Brncui din Trgu Jiu, seria Inginerie, nr.2/2010, pp 35-44, ISSN 1842-4856, Revist categoria B+, [1]Popescu, Luminia Georgeta -Aplicaii ale liniarizrii exacte prin reacii la acionrile de curent continuu, Analele Universitii Constantin Brncui din Trgu Jiu, seria Inginerie, nr.1/2009, pp 7-14, ISSN 1842-4856, Revist categoria B+, [20]Rdulescu, Gh., Ilea, M. Fizico-chimia i tehnologia uleiurilor lubrifiante, Editura Tehnic, Bucureti, 182, [21]Sofroni, L.: Fonta cu grafit nodular,Editura Tehnica, Bucuresti, 1978. [22]Trusculescu, M.: Studiul metalelor, Editura Didactica si Pedagogica ,Bucuresti ,,1978. [23]Stancioiu,Alin.,-RESEARCH ON THE INFLUENCE OF HEAT TREATMENT ON THE OF THE STEEL CUTTING TOOLS (PART I) .Annal s of t he Cons t antin Brncui Uni ve r s i t y of Tr g u -Jiu,Engineering Series, Issue 4/2013. [24]Stancioiu,Alin.,- RESEARCH ON THE INFLUENCE OF HEAT TREATMENT ON THE OF THE STEEL CUTTING TOOLS (PART II). Annal s of t he Constantin Brncui Uni ve r s i t y of Trgu -Jiu,Engineering Series, Issue 4/2013. [25]Stancioiu,Alin.,-Concerning economicity of the techological process for manufacturing a piece. Methods to reduce costs.Fiabilitate si Durabilitate - Fiability & Durability Supplement No 1/ 2014 Editura Academica Brncui ,2014, Trgu Jiu, ISSN 1844 640X 320 .